RS700-E10 系列 RS700-E10-RS12U 1U 機架式伺服器 使用手冊
T18110 1.00 版 2021 年 6 月發行 版權說明 ©ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項...................................................................................................................................vii 用電安全.......................................................................................................................................... viii 電磁安全.............................................................................................................................. viii 靜電元件................................................................................
目錄 2.6 擴充插槽................................................................................................................................2-20 2.6.1 安裝擴充卡至轉接卡支撐架...........................................................................2-21 2.6.2 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至 PCIe 轉接卡支撐架........2-26 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架............................................................2-29 2.6.4 安裝乙太網路擴充卡至蝴蝶型轉接卡支撐架.........................................2-32 2.6.5 安裝華碩 PIKE II 卡...................................
目錄 5.2.4 子選單........................................................................................................................ 5-8 5.2.5 操作功能鍵說明..................................................................................................... 5-8 5.2.6 一般說明................................................................................................................... 5-8 5.2.7 設定值.....................................................................................................................
5.11 5.12 5.13 5.14 5.10.2 BMC 自我檢測記錄(BMC self test log).............................................5-60 5.10.3 網路設定..............................................................................................................5-61 5.10.4 檢視系統事件記錄(View System Event Log)..................................5-63 安全性選單(Security menu)...................................................................................5-64 開機選單(Boot menu)...............................................................................
使用注意事項 操作伺服器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照使用手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 伺服器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用伺服器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項周邊設備是否都已經連接妥當再開機。 ‧ 避免邊吃東西邊使用伺服器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近伺服器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入伺服器機件內,以避免引起機件短路,或是電路損毀。 ‧ 伺服器開機一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除周邊產品時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移伺服器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的訊號線之前,請先拔掉連接的電源線,或是先安裝訊號線 之後再安裝電源線。 ‧ 使用一隻手拆裝訊號線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊產生。 ‧ 伺服器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、記憶體、主機板、介面卡、磁碟機、硬碟機等設備,是由許多精密的積體 電路與其它元件所構成,這些積體電路很容易因為遭受靜電的影響而損壞。因此,在 拆裝任何元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝伺服器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與伺服器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸伺服器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜
關於本使用手冊 本使用手冊主要是針對有經驗且具有個人電腦硬體組裝知識的使用者所撰寫的。本 手冊可以幫助您建立起最新、功能強大的 RS700-E10-RS12U 華碩伺服器。手冊內容 介紹本產品各部份元件的拆裝、設定,因此,部份元件可能是選購配備,並未包含在 您的產品當中,假如您有需要選購該配備,請向本公司授權經銷商洽詢。 章節說明 本使用手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖示帶您認識華碩伺服器的功能及特色,包括系統的前、後面板以及 內部功能的介紹。 第二章:硬體安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本伺服器裡 頭。 第三章:進階安裝 本章提供您本伺服器的機架安裝及使用方法。 第四章:主機板資訊 本章提供您有關本伺服器內建主機板的相關資訊,包括主機板的構造圖、J u m p e r 設定以及連接埠位置等。 第五章:BIOS 程式設定 本章提供您本伺服器之 BIOS 的升級與管理及 BIOS 設定的相關訊息。 第六章:安裝驅動程式 本章節將提供您相關驅動程式的安裝與說明。 華碩 RS700-E10-RS12U 使用手冊 ix
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主機板元件。不當的 動作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照使用手冊所描述之方式 完成一項或多項軟硬體的安裝或設定。 說明:小祕訣,名詞解釋,或是進一步的資訊說明。提供有助於完成某 項工作的訣竅和其他額外的資訊。 哪裡可以找到更多的產品資訊 您可以經由下面所提供的兩個管道來獲得您所使用的華碩產品資訊以及軟硬體的升 級資訊等。 1. 華碩網站 您可以到 http://tw.asus.com 華碩電腦全球資訊網,來取得所有關於華碩軟硬體產品 的各項資訊。 2. ASUS Control Center(ACC)使用手冊 本使用手冊介紹如何設定並使用華碩伺服器管理工具,請至 asuscontrolcenter.asus.
產品之限用物質含有情況 「產品之限用物質含有情況」之相關資訊,請參考下表。 單元 鉛 (Pb) 汞 (Hg) 限用物質及其化學符號 六價鉻 鎘 (Cd) (Cr+6) 印刷電路板及其 o o o 電子組件 外殼 o o o o 散熱設備 o o o 電源供應器 o o o 其他及其配件 o o o 備考 1 "o" 係指該項限用物質之百分比含量未超出百分比含量基準值。 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o o o o o o o o 備考 2 "-" 係指該項限用物質為排除項目。 產品回收與處理 華碩與資源回收業者以最高標準相互配合,以保護我們的環境,確保工作者的安 全,以及遵從全球有關環境保護的法律規定。我們保證以資源回收的方式回收以往生 產的舊設備,透過多樣的方式保護環境。 如欲了解更多關於華碩產品資源回收資訊與聯絡方式,請連線上網至 CSR(Corporate Social Responsibility)網頁:http://csr.asus.com/english/Takeback.
xii
第一章: 系統導覽 本章將介紹本伺服器的各項組成元件,其中包括系統的 前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下為本伺服器包裝內的組件。 標準元件 機種型號 RS700-E10-RS12U 機殼 華碩 R12F 1U 機架式機殼 主機板 華碩 Z12PP-D32 伺服器主機板 硬體元件 1 x 80PLUS 電源供應器 1 x 2.5 吋儲存裝置背板 12 x 2.5 吋儲存裝置抽取架 2 x 風扇面板 1 x 前側 I/O 面板 2 x 轉接卡 9 x 系統風扇 配件 1 x 驅動與公用程式光碟片 螺絲一包 2 x 處理器散熱片 2 x AC 電源線 1 x 外接風扇模組(選配) 1 x OCP3.
1.
1.3 產品規格表 華碩 RS700-E10-RS12U 是一款精心打造的 1U 伺服器,內裝 Z12PP-D32 伺服器主 機板,支援第三代 Intel® Xeon® Scalable 處理器,並包含最新單晶片系統所提供的相 關技術。 機種型號 RS700-E10-RS12U 中央處理器 / 系統匯流排 2 x Socket P+(LGA 4189) 第三代 Intel® Xeon® Scalable 處理器 核心邏輯 Intel® C621A 晶片 總插槽數 32(每個 CPU 8 通道;每個 CPU 16 個記憶體模組) 擴充容量 最高可擴充達 6TB 記憶體類型 * 請參考華碩官方網站 tw.asus.
機種型號 主機板內建插 槽 預設排線 儲存裝置插槽 N V M e 升級選 項 RS700-E10-RS12U 2 x M.2 插槽 3 x Mini SAS HD 插槽 3 x Mini SAS HD to mini SAS HD 排線 2 x Slimline SAS 排線 支援 4 x NVMe:經由 2 x Slimline SAS 排線 支援 8 x NVMe:經由 4 x Slimline SAS 排線 支援 12 x NVMe:經由 6 x Slimline SAS 排線 * 網路功能 網路 VGA 顯示功能 前面板 I/O 裝置連接埠 後面板 I/O 裝置連接埠 最新更新資訊請參考 Asus server Upgrade Part List 4 x 1Gbe (Intel® I350-AM4)RJ45 網路埠或 2 x 10Gbe (Intel® X710-AT2)RJ45 網路埠 1 x 網路管理埠 選配 OCP 3.
機種型號 管理解決方案 RS700-E10-RS12U 外部遠端遙控 硬體 軟體 支援作業系統 內建 ASMB10-iKVM ,支援 KVM-over-IP 的方式 ASUS Control Center Windows® Server RedHat® Enterprise Linux SuSE® Linux Enterprise Server CentOS Ubuntu VMware * 請參考華碩官方網站 http://tw.asus.com 以查詢最新的作業系 統支援版本 安裝認證標準 BSMI、CE、CB、FCC(ClassB) 尺寸(深 x 寬 x 高) 淨重(不包含處理器、記憶體與儲 存裝置) 毛重(不包含處理器、記憶體、儲 存裝置;包含外包裝) 842.5 mm x 439.5 mm x 44 mm(1U) 電源供應器與電氣額定值 13.7 公斤 22.
1.4 前端面板 本伺服器的前端面板提供了簡單的存取功能,包括電源按鈕、重置按鈕、相關的 LED 指示燈,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7 顯示燈號說明。 機架螺絲 插槽 1 插槽 3 插槽 2 插槽 4 插槽 5 插槽 6 Asset tag (財產標籤) 插槽 7 插槽 10 插槽 12 插槽 9 插槽 11 機架螺絲 電源按鈕 電源指示燈 網路埠 1 與 3 指示燈 網路埠 2 與 4 指示燈 Location 指示燈 插槽 8 重置(Reset)按鈕 訊息指示燈 Location 開關 ‧ 插槽 1 至 8 預設支援 NVMe / SATA 硬碟裝置,SAS 硬碟則需搭配選 配的華碩 PIKE II 卡使用。 ‧ 插槽 9 至 12 預設支援 NVMe / SATA 硬碟裝置(支援 tri-mode 卡)。 ‧ 所有插槽皆支援 2.5 吋儲存裝置。 1.
1.6 內部組件 下圖即為本伺服器的標準內部組件: 1. 備援式電源供應器 2. 華碩 Z12PP-D32 伺服器主機板 3. 系統風扇 4. 風扇面板 5. 12 x 2.5 吋儲存裝置插槽 6. NVMe/SATA/SAS 背板(隱藏) 7. PCIe 轉接卡(隱藏) 8. 蝴蝶型轉接卡(Gen4 x16 link) 9. Asset Tag(財產標籤) 10. 外接風扇 (GPU 機種選配) 11.
1.7 LED 顯示燈號說明 1.7.
1.7.
1.7.
1.7.
1.7.
Action Quick VGA Normal boot PHASE POST CODE 0x70 0x7E 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD MRC Memory initialization 0xBE 0xBF 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF 0x32 0x33 0x34 0x35 0x36 0x37 0x3B 0x4F 0x60 DXE(Driver 0x61 Execution Environment)phase 0x62 0x63 0x68 0x69 0x6A 0x70 0x71 0x72 0x78 0x79 0x90 0x91 0x92 0x93 0x94 BDS(Boot Device 0x95 Selection) phase 0x96 0x97 0x98 0x99 0x9A TYPE Progress Progress Progress DESCRIPTION H
Action PHASE Normal boot BDS(Boot Device Selection) phase POST CODE 0x9B 0x9C 0x9D 0xA0 0xA1 0xA2 0xA3 0xA8 0xA9 0xAB 0xAD 0xAE 0xAF 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 TYPE Progress DESCRIPTION AMI USB Driver Initialization AMI USB Driver Initialization AMI USB Driver Initialization AHCI Initialization AHCI Initialization AHCI Initialization AHCI Initialization BIOS Setup password verify BIOS Setup start BIOS Setup input wait Ready to Boot event Legacy Boot event Exit Boot Services Legacy Option ROM Initi
1-16 第一章:系統導覽
第二章: 硬體安裝 本章節要告訴您如何安裝及移除本伺服器各個部分的組 件,以及在安裝過程中必需注意的事項。 2
2.1 機殼上蓋 2.1.1 打開機殼後半部上蓋 2-2 1. 使用螺絲起子鬆開機殼兩側的 2 顆螺絲。 2. 鬆開後側面板上的指旋螺絲。 3. 握住機殼上蓋向後推,使之鬆開脫離機殼。 4.
2.2 導風罩 2.2.1 移除導風罩 將導風罩由機殼內垂直取出。 2.2.
2.3 中央處理器(CPU) 本主機板具備 Socket P+ 處理器插槽,本插槽是專為第三代 Intel® Xeon® Scalable 處理器所設計。 • 在您購買本主機板之後,請確認在處理器插座上附有一個 PnP 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保護 蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在 安 裝 完 主 機 板 之 後 , 請 將 隨 插 即 用 的 保 護 蓋 保 留 下 來 。 只 有 在 S o c k e t P+ 插槽上附有隨插即用保護蓋的主機板符合 R e t u r n Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理 產品的維修與保固。 • 本保固不包括處理器插座因遺失、錯誤的安裝或不正確的移除隨插即 用保護蓋所造成的毀損。 2.3.1 移除中央處理器與散熱器(Type-A 散熱器) 請依照以下步驟移除中央處理器與散熱器(Type-A 散熱器): 1. 依照 2.1 機殼上蓋 的說明移除後半部上蓋。 2. 依照 2.2 導風罩 的說明移除導風罩。 3.
4. 鬆開所有固定散熱器的螺絲,並將散熱器由主機板上移除。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 5. 將散熱器翻面找到 CPU 托架,鬆開托架握把以將 CPU 取下。 托架握把 6.
2.3.2 移除中央處理器與散熱器(Type-B 散熱器) 請依照以下步驟移除中央處理器與散熱器(Type-B 散熱器): 1. 依照 2.1 機殼上蓋 的說明移除後半部上蓋。 2. 依照 2.2 導風罩 的說明移除導風罩。 3.
4. 鬆開所有固定散熱器的螺絲,並將散熱器由主機板上移除。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 5.
6.
2.3.3 安裝中央處理器與散熱器(Type-A 散熱器) 1. 依照 2.2 導風罩 的說明移除導風罩。 2. 找到主機板上 CPU 插槽的位置。 3.
4. 移除主機板 CPU 插槽上的 PnP 保護蓋。 5. 將散熱器與 CPU 安裝至 CPU 插槽,並將散熱器擺放於最上方(A)。向外側下 壓散熱器四角的固定鎖,以將散熱器與 CPU 固定於 CPU 插槽(B)。 • 請確認 CPU 的三角形標誌對齊 CPU 插槽的三角形標誌。 • 散熱器呈對稱。 6. 依下圖順序,以順時針方向轉動固定散熱器的螺絲 2 次,以將散熱器固定於主機 板。 Intel® 建議使用扭力值為 8 lbf-in 的 T-30 螺絲起子。 7. 依照 2.
2.3.4 安裝中央處理器與散熱器(Type-B 散熱器) 1. 依照 2.2 導風罩 的說明移除導風罩。 2. 找到主機板上 CPU 插槽的位置。 3.
4. 移除主機板 CPU 插槽上的 PnP 保護蓋。 5. 將散熱器與 CPU 安裝至 CPU 插槽,並將散熱器擺放於最上方(A)。向外側下 壓散熱器四角的固定鎖,以將散熱器與 CPU 固定於 CPU 插槽(B)。 • 請確認 CPU 的三角形標誌對齊 CPU 插槽的三角形標誌。 • 散熱器呈對稱。 6.
7. 將剩餘的螺絲鎖緊以將散熱器固定於主機板。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 8. 依照 2.
2.4 系統記憶體 2.4.
2.4.
若您也想安裝 PMem,請參考下表進行設定。 Channel DDR4+BPS 4+4 F E H G DIMM_F1 DIMM_F2 DIMM_E1 DIMM_E2 DIMM_H1 DIMM_H2 DIMM_G1 DIMM_G2 BPS DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 8+4 DDR4 DDR4 8+8 DDR4 6+1 8+1 12+2 DDR4 Channel DDR4+BPS BPS BPS DDR4 DDR4 DDR4 BPS BPS DDR4 DDR4 BPS DDR4 BPS DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4
2.3.3 安裝記憶體模組 安裝 / 移除記憶體模組或其他的系統元件之前,請先暫時拔出電腦的電 源線。以避免一些會對主機板或元件造成嚴重損壞的情況發生。 請依照下面步驟安裝記憶體模組: 1. 先將記憶體模組插槽的固定卡榫扳 開。 2. 將記憶體模組的金手指對齊記憶體模 組插槽的溝槽,並且在方向上要注意 金手指的缺口要對準插槽的凸起點。 記憶體模組缺口 插槽凸起點 往外扳開記憶體模 組插槽的卡榫 記憶體插槽上的凹槽為設計僅一個方向供記憶體模組插入,請在裝入 前,確定記憶體模組與記憶體插槽上的安裝方向是契合的。 3. 最後緩緩將記憶體模組插入插槽中, 若無錯誤,插槽的卡榫會因記憶體模 組置入而自動扣到記憶體模組的凹孔 中。 卡榫會在記憶體模組 正確置入後自動扣上 請將記憶體模組缺口對準插槽的凸起點並垂直插入,以免造成記憶體模 組缺口損壞。 2.3.4 取出記憶體模組 請依照以下步驟取出記憶體模組: 1. 依照 2.1 機殼上蓋 的說明移除後端上 蓋板。 2. 壓下記憶體模組插槽的固定卡榫以鬆開 記憶體模組。 3.
2.5 安裝硬碟機 本系統支援 12 個 2.5 吋熱抽換 SATA/SAS/NVMe 儲存裝置(最多 8 x NVMe/SAS/ SATA + 4 x NVMe/SATA)。儲存裝置的安裝方式,是經由裝入連接在主機板 SATA/ SAS/NVMe 背板上的模組式硬碟擴充槽來使用。 插槽 1 插槽 3 插槽 5 插槽 7 插槽 9 插槽 11 插槽 2 插槽 4 插槽 6 插槽 8 插槽 10 插槽 12 ‧ 插槽 1 至 8 預設支援 NVMe / SATA 硬碟裝置,SAS 硬碟則需搭配選 配的華碩 PIKE II 卡使用。 ‧ 插槽 9 至 12 預設支援 NVMe / SATA 硬碟裝置。 ‧ 所有插槽皆支援 2.5 吋儲存裝置。 2.5.1 安裝 2.5 吋熱抽換 SATA/SAS/NVMe 儲存裝置 1.
2. 將握把朝左扳開時,硬碟槽便會向外滑出,請順勢將硬碟擴充槽往主機的前方抽 離。 3. 取出準備安裝的儲存裝置與螺絲配件。 4. 置入儲存裝置,再使用 4 顆螺絲,將儲存裝置鎖緊固定在硬碟槽內。 5. 當儲存裝置安裝完畢後,請以手緊握住硬碟槽握把置入系統的插槽中,將其輕推 至機殼底部。將板手輕輕地推回原位並輕扣固定,使硬碟槽能夠緊密地固定在機 殼中。 ‧ 當置入後,硬碟槽上的 SATA/SAS/NVMe 接頭會完全與背板上的插座 契合。 ‧ 如果硬碟槽有正確地安裝,您將會看到硬碟槽外緣與機殼呈現切齊的 狀態。 6.
2.6 擴充插槽 本伺服器具備二個 PCIE 插槽 - PCIE1 與 PCIE2。在這些插槽上已預先安裝一組轉 接卡支撐架與一組蝴蝶形轉接卡支撐架,讓您可以安裝 PCI Express 介面卡。當您需 要進行安裝擴充卡時,請先將轉接卡支撐架從機殼內取出。 轉接卡支撐架 2 轉接卡支撐架 1 轉接卡支撐架 1 轉接卡支撐架 1 支援 PCIe Gen4 插槽 1-2 上至下。 PCIe 插槽 插槽 1 插槽 2 插槽 3(內建) 運作模式 模式 1 模式 2 x16 x16 x8 x16 OCP 3.0 x8 轉接卡支撐架 2 轉接卡支撐架 2 支援 PCIe Gen4 插槽。 PCIe 插槽 插槽 4 2-20 第二章:硬體安裝 運作模式 x16 x8(當 M.
2.6.1 安裝擴充卡至轉接卡支撐架 在 PCIE1 插槽的轉接卡支撐架上已預先安裝兩組 PCIe x16 與一組 PCIe x8 插槽。 兩組 PCIe x16 插槽支援 x16 Gen4 links,最上方的 PCIe 插槽訊號來自 CPU1,最下 方的 PCIe 插槽訊號來自 CPU2。 PCIe x8 插槽則保留給 PIKE II 卡。 請依照以下步驟,安裝一張 PCIe x16(Gen4 x16 link)專屬卡如顯示卡至轉接卡 上: 1. 參考 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 的說明,移除 PCIE2 插槽上的蝴蝶 型轉接卡支撐架。 2.
3. 參考 2.6.5 安裝華碩 PIKE II 卡 的說明,移除預先安裝的華碩 PIKE II 卡。 4. 移除 PCIe 轉接卡支撐架上 slim PCIe 插槽連接的 2 條 Slimline PCIe 排線。 5. 準備好要安裝的擴充卡,並將 PCIe 轉接卡支撐架翻至另一面。 6.
7. (選配)使用 2 顆螺絲安裝 GPU 後托架,如下圖所示。 僅安裝顯示卡時才需依此步驟安裝。 8. 安裝擴充卡至 PCIe 轉接卡支撐架上的 PCIe x16 插槽,下圖以安裝顯示卡為例。 9.
10. 將步驟 4 移除的 2 條 Slimline PCIe 排線連接至 PCIe 轉接卡支撐架上的 slim PCIe 插槽。請確認將標示 7 的排線連接至標示 7 的 slim PCIe 插槽、標示 8 的 排線連接至標示 8 的 slim PCIe 插槽。 11. 參考 2.6.
12. 將 PCIe 轉接卡支撐架對齊機殼與主機板 PCIE1 插槽的凹槽垂直插入。 將 PCIe 轉接卡支撐架安裝至機殼時,請確認 PCIe 轉接卡支撐架下方或 裡頭沒有任何排線。 13. 鎖上指旋螺絲固定 PCIe 轉接卡支撐架。 14. 參考 2.6.
2.6.2 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至 PCIe 轉接卡支撐架 建議您將 OCP 3.0 插槽基板安裝至 PCIe 轉接卡支撐架上的 PCIE2 插槽。 請依照以下步驟 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至 PCIe 轉接卡支撐架: 1. 依照 2.6.1 安裝擴充卡至轉接卡支撐架 的步驟 1-6 移除 PCIe 轉接卡支撐架與金 屬支撐架。 2. 移除 PCIe 轉接卡支撐架上的螺絲。 3. 移除 PCIe 支撐架。 PCIe 支撐架 4. 將 OCP 3.0 支撐架安裝至 OCP 3.
5. 安裝 OCP 3.0 插槽基板至 PCIe 轉接卡支撐架上的 PCIE2 插槽。 6. 安裝 OCP 3.0 插槽基板後,將金屬支撐架鎖扣上,以將 OCP 3.0 插槽基板固定於 PCIe 轉接卡支撐架上。 7. 將 OCP 3.0 插槽基板上的 OCP_SIDE1 與 OCP_NCSI1 排線分別連接至 PCIe 轉接 卡支撐架上的 OCP_SIDE1 與 OCP_BUS1 插座。 8. 將來自主機板 SLMPCIE7 與 SLMPCIE8 插座的 Slimline PCIe 排線連接至 OCP 3.
9. 依照 2.6.1 安裝擴充卡至轉接卡支撐架 的步驟 10-13 將 PCIe 轉接卡支撐架安裝 至機殼上。 10. 將 OCP 3.0 卡安裝至系統後側的 OCP 3.0 插槽(A),確認 OCP 3.
2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 預先安裝於 PCIE2 插槽上的蝴蝶型轉接卡支撐架支援 Low Profile(LP)、半長 (Half-Length (HL))類型的 PCIE x16 擴充卡。 請依照以下步驟安裝 PCIE x16(Gen4 x16 link)擴充卡至蝴蝶型轉接卡支撐架: 1.
2. 將蝴蝶型轉接卡支撐架翻至另一面並移除金屬支撐架。 3.
4. 將蝴蝶型轉接卡支撐架對齊主機板 PCIEX2 插槽並垂直插入。 5.
2.6.4 安裝乙太網路擴充卡至蝴蝶型轉接卡支撐架 預先安裝的蝴蝶型轉接卡支撐架可支援四埠 Intel® I350-AM4 1G LAN 網路控制器 擴充卡或雙埠 Intel® X710-AT2 Gigabit 10G LAN 網路控制器擴充卡。 若您想要安裝後側外接風扇時,請勿安裝四埠 Intel® I350-AM4 1G LAN 網路控制器擴充卡。 請依照以下步驟安裝四埠 Intel® I350-AM4 1G LAN 網路控制器擴充卡或雙埠 Intel® X710-AT2 Gigabit 10G LAN 網路控制器擴充卡: 1. 依照 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 的步驟 1,由機殼上移除蝴蝶型轉 接卡支撐架。 2. 將蝴蝶型轉接卡支撐架翻面,安裝四埠 Intel® I350-AM4 1G LAN 網路控制器擴充 卡或雙埠 Intel® X710-AT2 Gigabit 10G LAN 網路控制器擴充卡至 PCIE_LAN1 插 槽(A),並鎖上 2 顆螺絲固定(B)。 雙埠 Intel® X710-AT2 Gigabit 10G LAN 網路控制器擴充卡 3.
2.6.5 安裝華碩 PIKE II 卡 您可以安裝華碩 PIKE II 卡以支援使用 SAS 儲存裝置。 請依照以下步驟安裝華碩 PIKE II 卡: 1. 取出準備安裝的華碩 PIKE II 卡。 2. 移除華碩 PIKE II 卡上 2 顆支撐架的 螺絲(A),然後將此支撐架取出後 (B)並保存好。 支撐架 3. 依照 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 的步驟 1,由機殼上移除蝴蝶型轉 接卡支撐架。 4.
5. 將金屬擋板(專屬插槽)安裝至華碩 PIKE II 卡上,並鎖上步驟 2 移除的螺 絲固定。 金屬擋板 6. 將華碩 PIKE II 卡安裝至 PCIe 轉接卡支撐架上的 PCIe 插槽,並鎖上指旋螺絲固 定。 7.
8. 依照 2.6.1 安裝擴充卡至轉接卡支撐架 的步驟 12-13 將 PCIe 轉接卡支撐架安裝 至機殼上。 請依照以下步驟移除華碩 PIKE II 卡: 1. 依照 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 的步驟 1,由機殼上移除蝴蝶型轉 接卡支撐架。 2. 移除華碩 PIKE II 卡上連接的 mini SAS HD 排線。 3.
2.6.6 安裝 M.2(NGFF)擴充卡 您可以安裝 M.2 擴充卡(最高支援 22110)至主機板上的 M.2(NGFF)插槽。 1. 參考 2.6.3 安裝擴充卡至蝴蝶型轉接卡支撐架 的說明移除蝴蝶型轉接卡支撐架。 2. 鬆開鎖定 PSU 導風罩的螺絲,並移除導風罩。 3. 找到主機板上的 M.
4. 在主機板上選擇欲安裝的 M.2 卡的螺絲孔位置,並鎖上螺絲座。 5. 將 M.2 擴充卡對準主機板上的 M.2(NGFF)插槽裝入 ,並鎖上螺絲固定。 6.
7.
2.6.7 設定擴充卡 1. 安裝好擴充卡之後,接著須藉由軟體設定來調整擴充卡的相關設定。 啟動電腦,然後更改必要的 BIOS 程式設定。若需要的話,您也可以參閱第五章 BIOS 程式設定以獲得更多資訊。 2. 為加入的擴充卡指派一組尚未被系統使用到的 IRQ。請參閱下表中所列出的中斷 要求使用一覽表。 3.
2.7 連接排線 ‧ 系統內的排線在出廠前都已經預先連接妥當。您不需再另外安裝,除 非您需要更換或安裝增加的硬體,才需要重新連接/移除。 ‧ 請參考第四章以了解更多關於排線與插座連接的相關資訊。 預先連接的系統排線 1. 4-pin BPPWR2 電源接頭(連接至背板) 2. 8-pin VGAPWR2 電源接頭(連接至背板) 3. 8-pin VGA 電源接頭(連接至顯示卡,選配) 4. 面板連接插座(連接至前置 I/O 面板) 5. 系統風扇連接插座(主機板 FAN1-4 至系統風扇) 6. Mini SAS 連接插座(主機板至背板) 7. SLMPCIE2、SLMPCIE3、SLMPCIE4、SLMPCIE6、SLMPCIE9、SLMPCIE10 Slim PCIe 連接插座(連接至背板) 8.
2.
2.9 儲存裝置設定與連接排線 本章節說明伺服器建議的儲存裝置設定方式,當您開始安裝或移除儲存裝置排線前 ,請先確認各硬碟插槽是否安裝正確的硬碟規格。 請參考 2.5 安裝硬碟機 的詳細說明。 插槽 1 插槽 3 插槽 5 插槽 7 插槽 9 插槽 11 插槽 2 插槽 4 插槽 6 插槽 8 插槽 10 插槽 12 ‧ 插槽 1 至 8 預設支援 NVMe / SATA / SAS 硬碟裝置,SAS 硬碟則需 搭配選配的華碩 PIKE II 卡使用。 ‧ 插槽 9 至 12 預設支援 NVMe / SATA 硬碟裝置。 ‧ 所有插槽皆支援 2.
2.9.1 12 x SATA 儲存裝置設定與連接排線 • 本章節圖示可能因機型而異,僅供參考。 • 在此設定下仍可支援 4、6 或 12 NVMe 儲存裝置,請參考以下章節 的說明。 - 4 NVMe 支援:2.9.2 4 x NVMe 儲存裝置設定與連接排線 - 8 NVMe 支援:2.9.3 8 x NVMe 儲存裝置設定與連接排線 - 12 NVMe 支援:2.9.4 12 x NVMe 儲存裝置設定與連接排線 背板連接埠 排線 連接至 MSAS_HD1 Mini-SAS HD(垂直)至 Mini-SAS HD(垂直) 主機板上的 ISSATA1 MSAS_HD2 Mini-SAS HD(垂直)至 Mini-SAS HD(垂直) 主機板上的 ISATA1 MSAS_HD3 Mini-SAS HD(垂直)至 Slimline PCIe 主機板上的 ISATA2 1. 請將硬碟機安裝至支援的硬碟插槽。 請參考 2.5 安裝硬碟機 的詳細說明。 SATA SATA 2.
3. 使用螺絲起子鬆開前側上蓋機殼兩側的 6 顆螺絲(A),並將上蓋往前推直到上 蓋與機殼脫離(B)。 4.
5. 連接 mini-SAS HD 排線至主機板和背板。 MSAS_HD3:連接主 機板 ISATA2 插座的 mini-SAS HD 排線 6.
7. 將前側上蓋往後端面板方向推直到固定在機殼上(A),接著鎖上先前移除的固 定螺絲(B)。 8.
2.9.2 4 x NVMe 儲存裝置設定與連接排線 • 本章節圖示可能因機型而異,僅供參考。 • 在此設定下仍可支援插槽 1 至 12 SATA 儲存裝置或插槽 1 至 8 SAS 儲存裝置,請參考以下章節的說明。 -插 槽 1 至 12 支援 SATA:2.9.1 12 x SATA 儲存裝置設定與連接 排線 -插 槽 1 至 8 支援 SAS 與插槽 9 至 12 支援 SATA: 2.9.5 8 x SAS 與 4 x SATA 儲存裝置設定與連接排線 背板連接埠 排線 連接至 SLMPCIE1 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE3 SLMPCIE2 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE4 1. 請將硬碟機安裝至支援的硬碟插槽。 請參考 2.5 安裝硬碟機 的詳細說明。 2.
3. 使用螺絲起子鬆開前側上蓋機殼兩側的 6 顆螺絲(A),並將上蓋往前推直到上 蓋與機殼脫離(B)。 4.
5. 連接 slimline PCIe 排線至主機板和背板。 SLMPCIE2:連接主機 板 SLMPCIE4 插座的 slimline PCIe 排線 6.
7. 將前側上蓋往後端面板方向推直到固定在機殼上(A),接著鎖上先前移除的固 定螺絲(B)。 8.
2.9.3 8 x NVMe 儲存裝置設定與連接排線 • 本章節圖示可能因機型而異,僅供參考。 • 在此設定下仍可支援插槽 1 至 12 SATA 儲存裝置或插槽 1 至 8 SAS 儲存裝置,請參考以下章節的說明。 -插 槽 1 至 12 支援 SATA:2.9.1 12 x SATA 儲存裝置設定與連接 排線 -插 槽 1 至 8 支援 SAS 與插槽 9 至 12 支援 SATA: 2.9.5 8 x SAS 與 4 x SATA 儲存裝置設定與連接排線 背板連接埠 排線 連接至 SLMPCIE1 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE3 SLMPCIE2 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE4 SLMPCIE3 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE2 SLMPCIE4 Slimline PCIe 至 Slimline PCIe 主機板上的 SLMPCIE9 1. 請將硬碟機安裝至支援的硬碟插槽。 請參考 2.
3. 使用螺絲起子鬆開前側上蓋機殼兩側的 6 顆螺絲(A),並將上蓋往前推直到上 蓋與機殼脫離(B)。 4.
5. 連接 slimline PCIe 排線至主機板和背板。 SLMPCIE2:連接主機 板 SLMPCIE4 插座的 slimline PCIe 排線 SLMPCIE4:連接主機 板 SLMPCIE9 插座的 slimline PCIe 排線 SLMPCIE3:連接主機 板 SLMPCIE2 插座的 slimline PCIe 排線 6.
7. 將前側上蓋往後端面板方向推直到固定在機殼上(A),接著鎖上先前移除的固 定螺絲(B)。 8.
2.9.4 12 x NVMe NVMe 儲存裝置設定與連接排線 • 本章節圖示可能因機型而異,僅供參考。 • 在此設定下仍可支援以下設定,請參考以下章節的說明。 -插 槽 1 至 12 支援 SATA:2.9.1 12 x SATA 儲存裝置設定與連接 排線 -插 槽 1 至 8 支援 SAS 與插槽 9 至 12 支援 SATA: 2.9.
3. 使用螺絲起子鬆開前側上蓋機殼兩側的 6 顆螺絲(A),並將上蓋往前推直到上 蓋與機殼脫離(B)。 4.
5. 連接 slimline PCIe 排線至主機板和背板。 SLMPCIE6:連接主機 板 SLMPCIE6 插座的 slimline PCIe 排線 SLMPCIE4:連接主機 板 SLMPCIE9 插座的 slimline PCIe 排線 SLMPCIE5:連接主機 板 SLMPCIE10 插座的 slimline PCIe 排線 6.
7. 將前側上蓋往後端面板方向推直到固定在機殼上(A),接著鎖上先前移除的固 定螺絲(B)。 8.
2.9.5 8 x SAS 與 4 x SATA 儲存裝置設定與連接排線 • 本章節圖示可能因機型而異,僅供參考。 • 在此設定下仍可支援 4、6 或 12 NVMe 儲存裝置,請參考以下章節 的說明。 - 4 NVMe 支援:2.9.2 4 x NVMe 儲存裝置設定與連接排線 - 8 NVMe 支援:2.9.3 8 x NVMe 儲存裝置設定與連接排線 - 12 NVMe 支援:2.9.4 12 x NVMe 儲存裝置設定與連接排線 背板連接埠 排線 連接至 MSAS_HD1 Mini-SAS HD(垂直)至 Mini-SAS HD(垂直) 華碩 PIKE II 卡 MSAS_HD2 Mini-SAS HD(垂直)至 Mini-SAS HD(垂直) 華碩 PIKE II 卡 MSAS_HD3 Mini-SAS HD(垂直)至 Slimline PCIe 主機板上的 ISSATA1 1. 請將硬碟機安裝至支援的硬碟插槽。 請參考 2.5 安裝硬碟機 的詳細說明。 2.
3. 使用螺絲起子鬆開機殼兩側的 6 顆機架螺絲(A),並將 6 顆機架螺絲取下 (B)。 4.
5. 取下前側上蓋即可看到背板(A),接著剪斷排線束帶(B)。 背板 6.
7. 用束帶將排線整理好(A),並將前側上蓋裝回機殼上(B)。 背板 8.
9.
2.10 移除系統組件 當您在安裝或移除系統裝置或是替換損壞的零組件時,或許需要移除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何移除與重新安裝下列各項系統組件。 1. 系統風扇 2. 備援式電源供應器模組 安裝/移除系統組件之前,請先關閉系統電源。 您可能需要在安裝組件前,先移除先前安裝的組件或出廠組件。 2.10.1 系統風扇 請依照以下的步驟,移除系統風扇: 1. 移除系統風扇連接主機板的排線。 2. 裝風扇取下並放置一旁。 3.
請依照以下的步驟安裝系統風扇: 1. 將系統風扇置入風扇擴充槽中。請注意在置入時的風扇氣流箭頭方向是朝系統後 側面板。 安裝時請確認風扇模組的凹槽對齊機殼上的凹槽。 2.
請依照以下的步驟安裝後側外接風扇(選配): ‧ 安裝 GPU 卡時建議安裝後側外接風扇。 ‧ 後側外接風扇為選配。 1. 請使用螺絲起子撬開插槽。 若您想要安裝後側外接風扇時,請勿安裝四埠 Intel® I350-AM4 1G LAN 網路控制器擴充卡。 2. 準備好要安裝的後側外接風扇。 3.
4. 將後側外接風扇的排線連接至主機板上的 REAR_FAN1 與 REAR_FAN2 插座。 5. 將後側外接風扇對齊機殼上的螺絲孔。 6.
2.10.2 備援式電源供應器模組 您可依照以下的步驟,更換損壞的備援式電源供應器模組: 1. 握住電源供應器模組上的拉把。 握把 2. 握住電源供應器上的握把,然後使用 拇指將右側的固定閂朝左推讓電源供 應器鬆脫。接著可以將此電源供應器 模組,從機殼中拉出。 握把 3.
第三章: 進階安裝 本章節要告訴您,如何使用滑軌套件將本伺服器安裝至 機架中,以及在安裝過程中必須注意的事項。 3
3.1 免工具標準式滑軌套件 免工具的滑軌套件設計,提供您輕鬆將滑軌裝上機架並安裝伺服器至機架中,而無 須使用任何工具。這個套件並提供金屬止擋,可以讓您在安裝伺服器時提供額外的支 撐和穩定性。 免工具滑軌套件包含了以下組件: 固定閂 螺絲組 固定閂螺絲 滑軌墊圈 滑軌螺絲 Tool-less rack rails 3.1.1 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1.
2. 選擇所需的空間和適當的機架滑軌(左和右)放在機架的相對位置上。 在這 1U 的空間裡面要有三個方形安裝孔與在上方與底部包含二個薄型的 間隔,如下圖圈選處。 1U 3. 上推彈簧鎖,然後將螺栓插入已選定在機架上的方形安裝孔。 4. 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 5.
6. 抬起伺服器,並裝入機架滑軌。 ‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈建議至少需要兩位身強體壯的人來執行這部份的安裝作業。 ‧ 如有必要,建議使用適當的起重工具以輔助吊裝。 請確認伺服器兩側的結點(knots)裝入機架滑軌的安裝孔裡。 圖示僅供參考。 3.1.2 滑軌尺寸 43.6mm 900mm 43.
3.2 滾珠軸承機架安裝套件 滑軌套件包含了以下組件: 2 x 1200 mm 機架滑軌(或 2 x 1000 mm 機架滑軌) 滑軌前端 機架滑軌 4 x #6-32X4L 螺絲 8 x ø17.
3.2.1 安裝機架滑軌 ‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈建議至少需要兩位身強體壯的人來執行這部份的安裝作業。 ‧ 如有必要,建議使用適當的起重工具以輔助吊裝。 ‧ 本節步驟以 1200 mm 機架滑軌為例,1000 mm 機架滑軌的安裝步驟 幾乎相同。 ‧ 本節圖示僅供參考。 請依照以下步驟,將機架滑軌安裝至機架上: 1. 選擇所需的空間和適當的機架滑軌 (左和右)放在機架的相對位置上。 1U 在這 1U 的空間裡面要有三 個方形安裝孔與在上方與底 部包含二個薄型的間隔,如 下圖圈選處。 2.
3. 按壓彈簧鎖,然後將滑軌後端螺栓插 入已選定在機架上的方形安裝孔。 後端機架 彈簧鎖 滑軌後端 4. 將中間滑軌向外滑動直到停止。 中間滑軌 5. 外滑軌 將內滑軌向外滑動直到停止。將白色膠片向外拉以移除內滑軌。 中間滑軌 內滑軌 藍色膠片 白色膠片 僅 1200mm 機架滑軌才有藍色膠片,可用於延長或收回中間滑軌。 6.
7. 移除機殼左右兩側的 3 顆螺絲,接著移除金屬板。 下圖僅顯示機殼的一側,另一側機殼的螺絲會在相同位置。 金屬板 8. 將內滑軌對準伺服器兩側的結點進行安裝,並朝伺服器後端滑動以固定。 2 1 9.
10. 抬起伺服器並裝入機架滑軌。 2 1 11. (選配)使用 M5X20L 螺絲將滑軌 固定於機架上。 前端機架 滑軌前端 12.
RS700-E10 前視圖 3-10 第三章:進階安裝
3.3 理線架(僅供 1200 mm 機架滑軌選配) 您可以額外安裝理線架(CMA)來幫助收納及配置伺服器的纜線。理線架設計為可 移動式元件,方便您依機架滑軌移動伺服器而不必移動理線架。 外側連接器 內側連接器 勾環綁帶 樞軸連接器 訊號線綁帶 3.3.1 安裝理線架 請依照以下步驟安裝理線架: 1. 安裝機架滑軌。 請參考 3.1 滑軌套件 的說明安裝機架滑軌。 2.
3. 將理線器上的 3 個連接器對齊機架滑軌上的連接器。 中間滑軌連接器 樞軸連接器 內滑軌連接器(隱藏) 內側連接器 中間滑軌連接器 外側連接器 本章節的安裝步驟以左樞軸為例,右樞軸的安裝步驟極為相似。 4. 將內滑軌連接器連接至理線架 上的內側連接器。 5.
6. 將另一端的中間滑軌連接器連接至理線架上的樞軸連接器。 7.
3-14 第三章:進階安裝
第四章: 主機板資訊 在本章中要告訴您在安裝系統元件時所必須完成的主機 板安裝程序。詳細內容有:頻率開關設定、跳線選擇區設 定以及主機板的各種裝置接頭。 4
4.
主機板的各項元件 跳線選擇區 頁碼 1. Clear RTC RAM (3-pin CLRTC1) 4-5 2. VGA controller setting (3-pin VGA_SW1) 4-6 3. Baseboard Management Controller setting (3-pin BMC_EN1) 4-6 4. DMLAN setting (3-pin DM_IP_SEL1) 4-7 5. IPMI SW setting (3-pin IPMI_SW1) 4-7 6. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-8 7. DDR4 Thermal Event jumper (3-pin DIMMTRIP1-2) 4-8 8. ME firmware force recovery setting (3-pin ME_RCVR1) 4-9 9. PCH_MFG1 setting (3-pin PCH_MFG1) 4-9 內部指示燈 頁碼 1.
4-4 內部連接插槽 頁碼 14. System panel connector (10-1 pin SYS_PANEL1; 14-1 pin SYS_ PANEL2) 4-20 15. Hard disk activity LED connector (4-pin HDLED1) 4-21 16. VPP_I2C connector (10-1 pin VPP_I2C1) 4-22 17. BMC Debug UART connector (3-pin BMC_DEBUGUART1) 4-22 18. CPLD JTAG1 connector (6-pin CPLD_JTAG1) 4-23 19. Liquid connector (12-1 pin LIQUID_CONN1) 4-23 20. System Management Bus (SMBUS) connector (5-1 pin SMBUS1) 4-24 21.
4.2 跳線選擇區 1.
2. VGA 控制器設定(3-pin VGA_SW1) 您可以透過本功能的設定來開啟或關閉主機板內建之 VGA 圖形顯示控制器功 能。預設值為 [1-2](開啟 VGA 功能)。 3.
4. DMLAN 設定(3-pin DM_IP_SEL1) 本跳線帽提供您選擇 DMLAN 設定。設定為 [2-3] 以強制 DMLAN IP 使用固定 模式(IP=10.10.10.10, submask=255.255.255.0)。 5.
7. Smart Ride Through(SmaRT)設定(3-pin SMART_PSU1) 本跳線帽提供您啟用或關閉 Smart Ride Through(SmaRT)功能。本功能預設 為啟用。設定為 [2-3] 以關閉本功能。當本功能開啟時,SmaRT 允許電源不足時 系統不間斷運作。 7.
8. ME 韌體強制回復設定(3-pin ME_RCVR1) 這組跳線帽提供您當 Intel Management Engine(ME,管理引擎)韌體發生損壞 時,可以快速回復。 9.
4.3 內部指示燈 1. 電力指示燈(SBPWR1) 當主機板上內建的電力指示燈(SBPWR1)亮著時,表示目前系統是處於正常 運作、省電模式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您 在置入或移除任何的硬體裝置之前,都必須先移除電源,等待警示燈熄滅才可進 行。請參考下圖所示。 2.
3. 訊息指示燈(MESLED1) 當這個內建的指示燈亮紅燈時,為發生一個 BMC 事件記錄。 4.
5.
4.4 元件與周邊裝置的連接 1. Mini-SAS HD 連接埠(ISATA1-2; ISSATA1) 本主機板內建 mini Serial Attached SCSI(SAS)HD 連接埠,支援 Serial ATA。每個連接埠最多支援 4 個裝置。 2.
3. USB 2.0(10-1 pin USB78) 這些插槽可用來連接 U S B 2.0 連接埠。將 U S B 擴充套件連排線連接到 USB34,然後將擴充套件安裝到機殼背部的一個空置插槽位置。這些 USB 擴充套 件排線插槽支援 USB 2.0 規格,傳輸速率高達 480 Mbps。 USB 模組為選購配備,請另行選購。 4. USB 3.2 Gen 1 連接插槽(U31G1_34; Type-A USB3_1) 這個插槽用來連接 USB 3.2 Gen 1 模組,可在前面板或後側連接埠擴充 USB 3.2 Gen 1 模組。當您安裝 USB 3.2 Gen 1 模組,您可以享受 USB 3.2 Gen 1 的益 處,包括有更快的資料傳輸率最高達 10 Gb/s、對可充電的 USB 裝置更快的充電 速度、最佳化能源效率,以及與 USB 2.
5. 機殼開啟警示連接排針(2-pin INTRUSION1) 這組排針提供給設計有機殼開啟檢測功能的電腦主機機殼之用。此外,尚須搭 配一個外接式檢測裝置,譬如機殼開啟偵測感應器或者微型開關。在本功能啟用 時,若您有任何移動機殼元件的動作,感應器會隨即偵測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機殼開啟事件。預設設定為 CASEOPEN 與 GND 接腳短路,此功能關閉。 6.
7. 系統風扇插座(8-pin FRNT_FAN1-4; 6-pin REAR_FAN1-2) 這些插座支援連接 0.8A–1.0A(最大 12 W)或總合 6.4 A–8.0 A(最大 96 W)的 +12V 冷卻風扇使用。將風扇電源線連接到主機板上的風扇插座,請確認 黑線需接到風扇電源插座上的接地端(GND)。連接風扇電源插座時,一定要注 意到極性問題。 千萬要記得連接風扇的電源,若系統中缺乏足夠的風量來散熱,那麼很 容易因為主機內部溫度逐漸昇高而導致當機,甚至更嚴重者會燒毀主機 板上的電子元件。 8.
9. M.2(NGFF)插槽(NGFF1-2) 本插槽提供安裝一個 M.2 裝置。 此插槽支援 2260/2280 類型的 PCI-E 儲存裝置。 M.2(NGFF)裝置為選購配備,請另行選購。 10.
11. VGA 電源插座(8-pin VGAPWR1, VGAPWR3, VGAPWR4, BPPWR1) 這些插座供連接顯示卡的電源供應器使用。電源供應器只能以單一方向安裝至 VGA 電源插座。安裝時請確認電源供應器確實安裝且方向正確。 請勿將後側面板連接至此插座,否則會使系統發生錯誤,並對主機板或 裝置造成永久損壞。 12.
13. Micro SD 記憶卡插槽(MSD1) 主機板支援 SD 記憶卡 v2.00(SDHC) / v3.
14.
• Locator 按鈕/開關(BMCLOCBTN#) 這組排針為連接前面板 Locator 按鈕。這個按鈕按下後 Locator 指示燈將會亮 燈。 • 硬碟動作指示燈號接針(HDLED) 這組排針可連接到電腦主機面板上的硬碟動作指示燈,一旦硬碟有存取動作 時,指示燈隨即亮起。 15.
16. VPP_I2C1 連接插槽(10-1 pin VPP_I2C1) 這個插槽供 Intel VMD 功能與感應器讀取使用。 17.
18. CPLD JTAG 插槽(6-pin CPLD_JTAG1) 本插槽可用以燒錄 CPLD JTAG。 19.
20. 系統管理匯流排連接埠(5-1 pin SMBUS1) 此連接埠控制系統與電源管理相關任務。此匯流排透過兩條訊號線處理與裝置 間的訊號傳送與接收。 21.
第五章: BIOS 程式設定 BIOS 程式調校的優劣與否,和整個系統的運作效能有極 大的關係。針對自己的配備來作最佳化 BIOS 設定,可讓 您的系統性統再提升。本章節將逐一說明 BIOS 程式中的 每一項組態設定。 5
5.1 管理、更新您的 BIOS 程式 下列軟體讓您可以管理與更新主機板上的 BIOS 設定。 1. ASUS CrashFree BIOS 3 當 BIOS 程式毀損時,使用可開機的 USB 隨身碟來更新 BIOS 程式。 2. ASUS EzFlash 使用 USB 隨身碟更新 BIOS。 3. BUPDATER 使用可開機的 USB 隨身碟在 DOS 環境下更新 BIOS 程式。 上述軟體請參考相關章節的詳細使用說明。 建議您先將主機板原始的 BIOS 程式備份到可開機的 USB 隨身碟中, 以備您往後需要再度安裝原始的 BIOS 程式。使用華碩線上更新(ASUS Update)程式來拷貝主機板原始的 BIOS 程式。 5.1.
5.1.2 使用華碩 EzFlash 更新程式 華碩 EzFlash 程式讓您能輕鬆的更新 BIOS 程式,可以不必再透過開機片的冗長程 序或是到 DOS 模式下執行。 請至華碩網站 http://tw.asus.com 下載最新的 BIOS 程式檔案。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式。來到 Tools 選單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUSTek.
5.1.3 BUPDATER 工具程式 以下的 BIOS 畫面僅供參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程式可以提供您在 DOS 環境下,使用儲存有更新的 BIOS 檔案的 USB 隨身碟來更新 BIOS 檔案。 更新 BIOS 檔案 請依照以下的步驟,使用BUPDATER 工具程式來更新 BIOS 檔案: 1. 請先造訪華碩網站(tw.asus.com)下載最新主機板的 BIOS 檔案。並將檔案儲存 至可開機的 USB 隨身碟內。 2. 然後將華碩支援網站(support.asus.com)上的 BUPDATER 工具程式(BUPDATER. exe),下載並儲存至同一個可開機的 USB 隨身碟內。 3. 將系統開機至 DOS 環境下,然後使用鍵盤輸入指令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 USB 隨身碟裡頭的最新或原本 BIOS 檔案名 稱,然後按 鍵。 A:\>BUPDATER /i[file name].
4. 程式會進行檢查檔案,然後開始更新 BIOS 檔案。 ASUSTek. EzFlash Utility Current Platform Platform : Z12PP-D32 Version : 0215 Build date: 12/13/2020 Start Programming Flash. New Platform Platform : Z12PP-D32 Version : 0401 Build date: 02/09/2021 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程式檔案時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程式會回到 DOS 畫面,請重新啟動系統,透過硬碟開機。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS700-E10-RS12U 使用手冊 5-5
5.2 BIOS 程式設定 主機板擁有一片可編輯的韌體晶片,您可以依照 5.
5.2.1 BIOS 程式選單介紹 選單項目 功能表列 設定值 一般說明 操作功能鍵 5.2.
5.2.3 選單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 選單的項目。 點選選單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子選單 在選單畫面中,若功能選項的前面有一個小三角形標記,代表此為子選單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子選單。 5.2.5 操作功能鍵說明 在選單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動變更。 5.2.7 設定值 這些存在於選單中的設定值是提供給使用者選擇與設定之用。這些項目中,有的 功能選項僅為告知使用者目前運作狀態,並無法更改,那麼此類項目就會以淡灰色顯 示。而可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表 這是可更改的項目。 5.2.
5.3 主選單(Main) 當您進入 BIOS 設定程式時,首先出現的第一個畫面即為主選單,內容如下圖。 5.3.1 System Language [English] 設定系統使用語言。 5.3.2 System Date [Day xx/xx/xxxx] 設定您的系統日期。 5.3.
5.
Engine Boost [Disabled] 啟用本項目以增進處理器頻率。設定值有:[Disabled] [Normal] [Aggressive] 建議使用環境溫度低於 25℃ 以維持最佳效能。 Overclocking [Disabled] 啟用本項目以增進處理器時鐘。設定值有:[D i s a b l e d] [L e v e l1] [L e v e l2] [Level3(Max)] 請留意超頻設定可能會造成元件或系統損毀,並減少系統與處理器的使 用年限,進行設定前請謹慎評估風險。 Power Balancer 項目只有在 Core Optimizer 設定為 [Disabled] 時才會出 現。 Power Balancer [Disabled] 根據目前使用率動態調整所有處理器核心頻率,可提升每瓦特的效能以增進系統節 能。設定值有:[Disabled] [Enable Auto] [Enable Manual] 5.
5.6 進階選單(Advanced menu) 在進階選單(Advanced menu)裡的項目,為提供您變更 CPU 與其他系統裝置的設 定。 請注意當變更進階選單(Advanced menu)裡的項目時,在欄位中輸入不 正確的數值將會導致系統運作不正常。 5.6.
5.6.2 Trusted Computing Security Device Support [Enabled] 可讓您啟動或關閉 BIOS 安全裝置支援功能。設定值有:[Disabled] [Enabled] 5.6.3 ACPI 設定 Enable ACPI Auto Configuration [Disabled] 本項目為啟用或關閉 BIOS ACPI 自動設定。設定值有:[Disabled] [Enabled] 5.6.
IP Mask address 本項目可以設定 IP 網路遮罩位址。 IP Port 本項目可以設定 IP 埠。 5.6.
以下項目只有在 LAN Enable 設定為 [JumperState] 時才會出現。 ROM Type [PXE] 提供您選擇 L A N R O M(I n t e l 網路隨選唯讀記憶體)類型。設定值有: [Disabled] [PXE] [iSCSI] Intel I350 LAN2 LAN Enable [JumperState] 提供您啟用或關閉 Intel 網路。設定值有:[Disabled] [JumperState] 以下項目只有在 LAN Enable 設定為 [JumperState] 時才會出現。 ROM Type [Disabled] 提供您選擇 L A N R O M(I n t e l 網路隨選唯讀記憶體)類型。設定值有: [Disabled] [PXE] [iSCSI] Intel I350 LAN3 LAN Enable [JumperState] 提供您啟用或關閉 Intel 網路。設定值有:[Disabled] [JumperState] 以下項目只有在 LAN Enable 設定為 [JumperState] 時才會出現。 ROM Type [Disabled
5.6.
Parity [None] 一個 p a r i t y(同位)位元能發送資料位元來檢測一些傳輸錯誤,[M a r k] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為偶數。 [Odd] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為奇數。 [Mark] 同位位元總是 1。 [Space] 同位位元總是 0。 Stop Bits [1] Stop bits 為序列資料封包的終點(開始位元表示起始)。標準設定是 1 Stop bit。使用較慢的裝置通訊可能會需要超過 1 stop bit。設定值有:[1] [2] Flow Control [None] Flow control(流量控制)能預防在緩衝區溢滿時的資料流失。當傳送資料時, 若接收的緩衝區已經滿了,此時會送出“stop”(停止)訊號來停止傳送資料流 (data flow)。當緩衝區空出時,會再送出“start”(開始)訊號以重新開始傳 送資料流。硬體流量控制使用兩條金屬線來傳送 start/stop(開始/停止)訊號。
Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS) Settings Console Redirection EMS [Enabled] 啟用或關閉控制台轉向功能。設定值有: [Disabled] [Enabled] 當 Console Redirection 設定為 [Enabled] 時,以下的項目才會顯示。 Console Redirection Settings Out-of-Band Mgmt Port [COM1] 經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[COM1] [COM2] Terminal Type [VT-UTF8] 此為微軟 Windows Emergency Management Services (EMS) 提供 Windows Server 作業系統可以透過序列埠來採用遠端遙控管理。設定值有:V T100] [V T100+] [VT-UTF8] [ANSI] Bits per second [115200] 此為微軟 Wind
5.6.7 SIO Common 設定 Lock Legacy Resources [Disabled] 本項目可以啟用或關閉 Legacy 資源鎖定。設定值有:[Disabled] [Enabled] 5.6.
5.6.
5.6.
5.6.
5.6.
5.6.
5.6.
5.6.
5.7 平台設定選單(Platform Configuration menu) IntelRCSetup 選單提供更改平台設定。 請注意在欄位中輸入不正確的數值將會導致系統運作不正常。 5.7.
以下的項目僅當 SATA Controller 設定為 [Enabled] 時才會出現。 Configure SATA as [AHCI] 提供您識別 SATA 埠為連接 Solid State Drive(SSD)硬碟或硬碟機裝置。設 定值有:[AHCI] [RAID] SATA Mode options SATA HDD Unlock [Enable] 本項目設定為 [E n a b l e d] 時,將會開啟硬盤密碼。設定值有:[D i s a b l e] [Enable] SATA Led locate [Enabled] 本項目設定為 [E n a b l e d] 時,會附加 L E D/S G P I O 硬體。設定值有: [Disabled] [Enabled] Support Aggressive Link Power Management [Enabled] 啟用或關閉 Suport Aggressive Link Power (SALP) 管理功能。設定值有: [Disabled] [Enabled] SATA Port 0-7 Hot Plug [Disabled] 可讓您啟
5.7.
5.7.
5.7.
以下的項目僅當 Memory Error 設定為 [Enabled] 時才會出現。 Memory Corrected Error [Enable] 本項目可以啟用或關閉 Memory Corrected Error。設定值有:[Disable] [Enable] 以下的項目僅當 Memory Corrected Error 設定為 [Enabled] 時才會出現。 Spare Interrupt [SMI] 本項目可以選擇 Spare Interrupt。設定值有:[Disable] [SMI] [Error Pin] [CMCI] PMem CTLR Errors [Enable] 本項目可以啟用或關閉 PMem CTLR Error Reporting & Logging。設定值有: [Disable] [Enable] PMem CTLR Low Priority Error Signaling [SMI] 本項目可以設定低優先級錯誤訊號。設定值有:[Disable] [SMI] [ERR0# Pin] PMem CTLR High Priority Error Signaling [SMI]
IIO Error Enabling IIO/PCH Global Error Support [Enable] 本項目可以啟用或關閉 I I O/P C H G l o b a l E r r o r 支援。設定值有:[D i s a b l e] [Enable] 以下的項目僅當 IIO/PCH Global Error Support 設定為 [Enabled] 時才會 出現。 Os Native AER Support [Disable] 為 AER 錯誤處理選擇 FFM 或 OS 原生。設定值有:[Disable] [Enable] IIO Error Registers Clear [Enable] 本項目可以啟用或關閉 Clear IIO Error Registers。設定值有:[Disable] [Enable] PCIe Error Enabling Corrected Error [Enable] 本項目可以啟用 & 升級錯誤 PIN 的可更正錯誤。設定值有:[Disable] [Enable] Uncorrected Error [Enable] 本項目可以啟用 & 升級錯誤
5.
5.8.
L2 RFO Prefetch Disable [Disabled] 本項目提供您開啟或關閉 L2 RFO prefetcher。設定值有:[Disabled] [Enabled] Adjacent Cache Line Prefetch [Enabled] 本項目提供您啟用或關閉 Adjacent Cache Line Prefetch 功能。設定值有:[Disabled] [Enabled] DCU Streamer Prefetcher [Enabled] 本項目為啟用或關閉 L1 資料 prefetcher。設定值有:[Disabled] [Enabled] DCU IP Prefetcher [Enabled] 本項目提供您啟用或關閉下一個基於隨著在載入記錄之上的 L1 線。設定值有: [Disabled] [Enabled] LLC Prefetch [Disabled] 本項目提供您啟用或關閉 LLC Prefetch。設定值有:[Disabled] [Enabled] DCU Mode [Normal] [Normal] 整個 DCU 使用於快取。 [Mirror-Mode]
PSMI Configuration Global PSMI Enable [Enable] 設定值有:[Disable] [Enable] [Force setup] 以下的項目僅當 Global PSMI Enable 設定為 [Enabled] 或 [Force setup] 時才會出現。 Socket 0 Configuration PSMI Enable [Disable] 設定值有:[Disable] [Enable] 以下的項目僅當 PSMI Enable 設定為 [Enabled] 時才會出現。 PSMI Handler Size [256K] 設定值有:[256K] [512K] [1M] PSMI Trace Region 0-4 [Disable] 設定值有:[Disable] [Enable] 5.8.
5.8.
以下的項目僅當 Volatile Memory Mode 設定為 [2LM] 時才會出現。 AppDirect cache [Disabled] 本項目用來開啟或關閉記憶體區域的快取。設定值有:[Disabled] [Enabled] eADR Support [Disable] 本項目用來開啟或關閉 eADR 支援。設定值有:[Disable] [Enable] [Auto] 以下的項目僅當 eADR Support 設定為 [Enable] 或 [Auto] 時才會出現。 CPU Cache Flush Mode [Parallel] 本項目可以設定 CPU Cache Flush Mode。設定值有:[Serial] [Parallel] Memory RAS Configuration 顯示並提供選項以變更記憶體 RAS 設定。 Correctable Error Threshold [7FFF] 本項目可以設定 Correctable Error Threshold(0x01 - 0x7fff)。 5.8.
IOU3 (IIO PCie Port 4) [x16] 本項目可以為選擇的插槽選擇 P C I e 埠拆分。設定值有:[A u t o] [x4x4x4x4] [x4x4x8] [x8x4x4] [x8x8] [x16] IOU4 (IIO PCie Port 5) [x16] 本項目可以為選擇的插槽選擇 P C I e 埠拆分。設定值有:[A u t o] [x4x4x4x4] [x4x4x8] [x8x4x4] [x8x8] [x16] Enable PCI-E Completion Timeout (Per-Port) [No] 本項目用來開啟或關閉 Device Control2 暫存器的 PCIe Completion Timeout。 設定值有:[Yes] [No] Sck0 RP Correctable Err [No] 僅適用於根埠。本項目用來開啟或關閉可更正錯誤時中斷。設定值有:[Y e s] [No] Sck0 RP NonFatal Uncorrectable Err [No] 僅適用於根埠。本項目用來開啟或關閉非致命錯誤時中斷。設定值有:[Y e s] [No] Sck0
Sierra Peak Memory Region Buffer Size [None] 為每個 S i e r r a P e a k 設定記憶體緩衝的大小。設定值有:[N o n e] [1M B] [8MB] [64MB] [128MB] [256MB] [512MB] [1GB] Port 0/DMI 設定相關 PCI Express 埠(0/1A/1B/1C/1D/2A/2B/2C/2D/3A/3B/3C/3D/4A4B/4C/4 D/5A/5B/5C/5D)。 Link Speed [Auto] 選擇此 PCIe 埠的速度。設定值有:[Auto] [Gen 1 (2.5 GT/s)] [Gen 2 (5 GT/ s)] [Gen 3 (8 GT/s)] 以下的項目僅當 Link Speed 設定為 [Auto]、[Gen 2 (5 GT/s)] 或 [Gen 3 (8 GT/s)] 時才會出現。 PCI-E Port DeEmphasis [-6.0 dB] 將此 PCIe 埠解加強控制(LNKCON2 [6])。設定值有:[-6.0 dB] [-3.
MSI [Disable] 設定值有:[Disable] [Enable] PCI-E Extended Sync [No] 本項目用來開啟或關閉當 x 為 0-9 時的 Extended Sync Mode(D:x F:0 0:7Ch B:7)。設定值有:[No] [Yes] Compliance Mode [No] 本項目用來為此 PCIe 埠開啟或關閉 Compliance Mode。設定值有:[No] [Yes] EOI [Enable] 設定值有:[Disable] [Enable] Fatal Err Over [No] 本項目用來為此 PCIe 埠開啟或關閉致命錯誤傳播至 IIO 核心錯誤邏輯。設 定值有:[No] [Yes] Non-Fatal Err Over [No] 本項目用來為此 PCIe 埠開啟或關閉非致命錯誤傳播至 IIO 核心錯誤邏輯。 設定值有:[No] [Yes] Corr Err Over [No] 本項目用來為此 PCIe 埠開啟或關閉可更正致命錯誤傳播至 IIO 核心錯誤邏 輯。設定值有:[No] [Yes] ACPI PME Interrupt [No] 本項目用來開
ECRC Check [Disable] 本項目用來開啟或關閉 E C R C 檢查(E r r o r C a p a b i l i t i e s a n d C o n t r o l Register)。設定值有:[Disable] [Enable] SERRE [Disable] 本項目用來開啟或關閉 SERRE(SERR Reporting Enable)。設定值有: [Disable] [Enable] IODC Configuration [KTI Option] 本項目用來開啟或關閉 IODC(IO Direct Cache)。設定值有:[KTI Option] [Auto] [Enable for Remote InvItoM Hybrid Push] [InvItoM AllocFlow] [Enable for Remote InvItoM Hybrid AllocNonAlloc] [Enable for Remote InvItoM and Remove WViLF] MCTP [Yes] 本項目用來開啟或關閉 MCTP。設定值有:[No] [Yes] Extra Bus Res
以下的項目僅當 PCI-E Port 設定為 [Auto] 或 [Enable] 時才會出現。 Hot Plug Capable [Auto] 本項目用來指定鏈接是否可熱抽換。設定值有:[Auto] [Disable] [Enable] Surprise Hot Plug Capable [Disable] 本項目用來指定鏈接是否可意外熱抽換。設定值有:[Disable] [Enable] PCI-E Port Link Disable [No] 本項目用來關閉鏈接。設定值有:[No] [Yes] Link Speed [Auto] 選擇此 PCIe 埠的速度。設定值有:[Auto] [Gen 1 (2.
以下的項目僅當 PCI-E ASPM Support 設定為 [Auto] 或 [L1 Only] 時才會 出現。 PCI-E Port L1 Exit Latency [8uS - 16uS] 此 P C I e 埠要完成 L1 至 L0 傳輸的時間長度。設定值有:[<1u S] [1u S - 2uS] [2uS - 4uS] [4uS - 8uS] [8uS - 16uS] [16uS - 32uS] [32uS - 64uS] [>64uS] MSI [Disable] 設定值有:[Disable] [Enable] PCI-E Extended Sync [No] 本項目用來開啟或關閉當 x 為 0-9 時的 Extended Sync Mode(D:x F:0 0:7Ch B:7)。設定值有:[No] [Yes] PCI-E Detect Wait Time [Auto] 設定 PCIe 埠 TxRx 偵測輪詢。設定值有:[Disable] [500ms] [Auto] Compliance Mode [No] 本項目用來為此 PCIe 埠開啟或關閉 Compliance Mode。設定值有:[N
Unsupported Request [Disable] 本項目可以控制當 IIO 自我偵測來自 PCI Express/DMI 埠的要求不支援時進 行回報。設定值有:[Disable] [Enable] Alternate TxEq [Disable] 本項目用來開啟或關閉 TxEq。設定值有:[Disable] [Enable] SRIS [Disable] 本項目用來開啟或關閉 SRIS。設定值有:[Disable] [Enable] ECRC Generation [Disable] 本項目用來開啟或關閉 E C R C 產生(E r r o r C a p a b i l i t i e s a n d C o n t r o l Register)。設定值有:[Disable] [Enable] ECRC Check [Disable] 本項目用來開啟或關閉 E C R C 檢查(E r r o r C a p a b i l i t i e s a n d C o n t r o l Register)。設定值有:[Disable] [Enable] SERRE [Disable] 本項目用來
Reserved Memory [0] 根橋接器的預留記憶體範圍。設定值有:[0] - [1200] Reserved Memory Alignment [1] 設定值有:[1] - [31] Reserved Prefetchable Memory [0] 根橋接器的預留可預取記憶體範圍。設定值有:[0] - [1200] Reserved Prefetchable Memory Alignment [1] 設定值有:[1] - [31] 64 bit Reserved Prefetchable Memory [0] 根橋接器的 64 bit 預留可預取記憶體範圍。設定值有:[0] - [1200] 64 bit Reserved Prefetchable Memory Alignment [1] 設定值有:[1] - [31] Reserved I/O [0] 根橋接器的 I/O(4K/8K/12K/16K/20K)範圍。設定值有:[0] [4] [8] [12] [16] [20] Intel® VT for Directed I/O (VT-d) Intel(R) VT for Directed I
MemBar1 size [25] 本項目可以設定 V M D M e m o r y B A R1 尺寸(i n b i t s M i n=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設定值有:[20] - [39] MemBar1 attribute [32-bit non-prefetchable] 本項目可以設定 V M D M e m o r y B A R1 屬性。設定值有:[32-b i t n o nprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] MemBar2 size [20] 本項目可以設定 V M D M e m o r y B A R2 尺寸(i n b i t s M i n=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設定值有:[20] - [39] MemBar2 attribute [64-bit non-prefetchable] 本項目可以設定 V M D M e m o r y B A R2 屬性。設定值有:[32-b
MemBar2 size [20] 本項目可以設定 V M D M e m o r y B A R2 尺寸(i n b i t s M i n=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設定值有:[20] - [39] MemBar2 attribute [64-bit non-prefetchable] 本項目可以設定 V M D M e m o r y B A R2 屬性。設定值有:[32-b i t n o nprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] VMD for Direct Assign [Disable] 本項目用來開啟或關閉 VMD for Direct Assign。設定值有:[Disable] [Enable] Intel® AIC Retimer/AIC SSD Technology (non-VMD) Intel® AIC Retimer/AIC SSD on Socket 0 Intel® AIC Retimer/AIC SSD HW at Stack1 [Di
以下的項目僅當 Intel® AIC Retimer/AIC SSD HW at Stack3 設定為 [Enable] 時才會出現。 Port 3A - 3D [Disable] 本項目用來開啟或關閉 NVMe Legacy 模式。設定值有:[Disable] [Enable] Hot Plug Capable [Disable] 本項目用來開啟或關閉 P C I e根埠的熱抽換功能。設定值有:[D i s a b l e] [Enable] Intel® AIC Retimer/AIC SSD HW at Stack4 [Disable] 宣布 Stack4(Port4A-4D)的 Intel® AIC Retimer/AIC SSD HW。必須覆蓋 IOU0 拆分。設定值有:[Enable] [Disable] 以下的項目僅當 Intel® AIC Retimer/AIC SSD HW at Stack4 設定為 [Enable] 時才會出現。 Port 4A - 4D [Disable] 本項目用來開啟或關閉 NVMe Legacy 模式。設定值有:[Disable] [Enable] Hot Plu
5.8.
AVX P1 [Normal] 本項目用來選擇 AVX P1 等級。設定值有:[Normal] [Level 1] [Level 2] Activate SST-BF [Disable] 本項目用來開啟或關閉 SST-BF。設定值有:[Disable] [Enable] 以下的項目僅當 Activate SST-BF 設定為 [Enable] 時才會出現。 Configure SST-BF [Enable] 本項目可以允許 BIOS 設定 SST-BF 優先核心,使 SW 不必進行設定。設定值 有:[Disable] [Enable] EIST PSD Function [HW_ALL] 設定值有:[HW_ALL] [SW_ALL] Boot performance mode [Max Performance] 在作業系統切換前允許您選擇 B I O S 的效能狀態。設定值有:[M a x Performance] [Max Efficient] [Set by Intel Node Manager] Energy Efficient Turbo [Enable] 本項目用來開啟或關閉 Energy
Perf P-Limit Clip [1F] 可以為 Perf P-Limit 設定的最大值。 Perf P-Limit Threshold [F] 非核心頻率臨界值以上,將會觸發插槽功能並開始嘗試提升其他插槽的頻 率。 Perf P-Limit [Enable] 本項目用來開啟或關閉以 P-Limit 效能。設定值有:[Disable] [Enable] Hardware PM State Control Hardware P-States [Native Mode] 本項目可以讓您在硬體 P-States 模式間切換。 [Disable] 硬 體 依 作 業 系 統 要 求 選 擇 P-state。(Legacy P-States) [Native Mode] 硬 體 依 作 業 系 統 指 示 選 擇 P-state。 [Out of Band Mode] 硬體自主選擇 P-state。(無作業 系統指示) [Native Mode with no Legacy Support] 硬 體 依 作 業 系 統 指 示 選 擇 P-state。(無 Legacy sup
Scalability [Disable] 本項目用來開啟或關閉核心效能至基於處理器最佳化的頻率縮放。設定值有: [Disable] [Enable] Native ASPM [Disabled] [Auto] BIOS 控制 ASPM。 [Enabled] OS 控制 ASPM。 [Disabled] ASPM 關閉。 CPU C State Control Enable Monitor MWAIT [Enable] 本項目用來開啟或關閉 Monitor 與 MWAIT 指示。設定值有:[Disable] [Enable] CPU C1 auto demotion [Enable] 本項目用來開啟或關閉 CPU 自動降級至 C1。請重新開機使設定生效。設定值 有:[Disable] [Enable] CPU C1 auto undemotion [Enable] 本項目用來開啟或關閉 CPU 自動降級至 C1。請重新開機使設定生效。設定值 有:[Disable] [Enable] CPU C6 Report [Auto] 本項目用來開啟或關閉 C P U C6 (A C P I C3)
CPU Thermal Management CPU T State Control Software Controlled T-States [Disabled] 本項目用來開啟或關閉 Software Controlled T-States。設定值有:[Disabled] [Enabled] 以下的項目僅當 Software Controlled T-States 設定為 [Enabled] 時才會 出現。 T-State Throttle Level [Disable] 晶片內建智能溫控調頻系統。設定值有:[D i s a b l e d] [6.25%] [12.5%] [18.75%][25.0%][31.25%][37.5%][43.75%][50.0%][56.25%][62.5%][68.75%] [75.0%] [81.25%][87.5%][93.
Workload Configuration [Balanced] 本項目用以設定最佳化工作負載特性。設定值有:[B a l a n c e d] [I/O Sensitive] Averaging Time Window [1A] 本項目用來控制 C0 和 P0 平均時間的有效視窗。 P0 TotalTimeThreshold Low [28] 本項目用來控制 C0 和 P0 平均時間的有效視窗。 P0 TotalTimeThreshold High [3F] 本項目用來控制 C0 和 P0 平均時間的有效視窗。 SAPM Control [Enable] 設定值有:[Enable] [Disable] EET Mode [Coarse Grained Mode] [Coarse Grained Mode] 決定是否允許使用者要求的 P1 Turbo。 [Fine Grained Mode] 決定允許多少的 Turbo。 5.
5.9.
以下的項目僅當 Log EFI Status Code 設定為 [Enabled] 時才會出現。 Convert EFI Status Codes to Standard Smbios Type [Disabled] 允許您開啟或關閉 EFI 狀態編碼轉變為標準 Smbios 編碼(不是所有都可以轉換) 。設定值有:[Disabled] [Enabled]。 5.9.
5.
5.10.1 系統事件記錄(System Event Log) 提供您變更 SEL 事件記錄設定。 變更選項後需重新開機才會生效。 SEL Components [Enabled] 本項目用來開啟或關閉開機自我檢測時錯誤或進度代碼的事件記錄。設定值有: [Disabled] [Enabled] 僅當 SEL Component 項目設為 [Enabled] 時,以下項目才會出現。 Erase SEL [No] 本項目用來選擇如何清除 SEL。設定值有:[No] [Yes, On next reset] [Yes, On every reset] 5.10.
5.10.
Router IP Address 本項目可以設定路由器 IP 位址。 Router MAC Address 本項目可以設定路由器 MAC 位址。 Configure IPV6 support DM_LAN1 / Shared LAN IPV6 support [Enabled] 本項目用來開啟或關閉 IPV6 支援。設定值有:[Enabled] [Disabled] 僅當 IPV6 support 項目設為 [Enabled] 時,以下項目才會出現。 Configuration Address source [Previous State] 選擇設定的網路通道的參數為靜態或動態。設定值有:[Previous State] [Static] [DynamicBmcDhcp] 僅當 Configuration Address Source 項目設為 [Static] 時,以下項目才會 出現。 Station IPV6 address 本項目用來設定 IPV6 位址。 Prefix Length 本項目可以設定前置位元長度(最多為 128)。 Configuration Router LAN1/2 Ad
5.10.
5.11 安全性選單(Security menu) 本選單可以讓您變更系統安全設定,並且提供您啟用或關閉安全開機(S e c u r e Boot)狀態與讓使用者設定系統模式(System Mode)狀態。 Administrator Password(設定系統管理員密碼) 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4.
User Password(設定使用者密碼) 請依照以下步驟設定使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟刪除使用者密碼(User Password): 1. 請選擇 Clear User Password 項目並按下 。 2. 在警告視窗輸入 並按下 。 5.11.
以下的項目僅當 Secure Boot Mode 設定為 [Custom] 時才會出現。 Install Default Secure Boot Keys 本項目可以載入預設的安全開機金鑰,包括 PK(Platform key)、(KEK(keyexchange key))、db(signature database)與 dbx(revoked signature database)。 所有安全開機金鑰的狀態會由未載入變更為載入。請儲存並重啟系統使變更生效。 Clear Secure Boot Keys 本項目將會刪除先前應用的的安全開機金鑰,包括 PK(Platform key)、(KEK (key-exchange key))、db(signature database)與 dbx(revoked signature database)。所有安全開機金鑰的狀態會由未載入變更為載入。請儲存並重啟系 統使變更生效。 Key Management 本項目僅當 Secure Boot Mode 設定為 [Custom] 時才會出現,提供您修改 Secure Boot(安全開機)變量與設定 Key Manag
Clear Secure Boot Keys 本項目將會刪除先前應用的的安全開機金鑰,包括 PK(Platform key)、(KEK (key-exchange key))、db(signature database)與 dbx(revoked signature database)。所有安全開機金鑰的狀態會由未載入變更為載入。請儲存並重啟系 統使變更生效。 Save all Secure Boot Variables 本項目可以儲存安全開機政策變量的 NVRAM 內容至目標檔案系統裝置的根目 錄檔案(EFI_SIGNATURE_LIST 資料格式)。 Enroll Efi Image 本項目可以允許 Secure Boot 模式時執行 Efi Image。註冊 PE image 的 SHA256 Hash 憑證至 Authorized Signature Database(db)。 Device Guard Ready Remove ‘UEFI CA’ from DB 由 Secure Boot DB 移除 Microsoft UEFI CA。 Restore DB defaults 將 DB 變
5.
POST Report [5 sec] 提供您設定想要的 POST(開機自我測試)回報等待時間,可選擇從 1 至 10 秒。設定值有:[1 sec] ~ [10 sec] [Until Press ESC] 5.12.
5.
5.14 離開 BIOS 程式(Exit) 本選單可以讓您讀取 BIOS 程式出廠預設值與離開 BIOS 程式。 按下 鍵並不會立即離開 BIOS 程式,要從此選單上選擇適當的項 目,或按下 鍵才會離開 BIOS 程式。 Discard Changes and Exit 本項目可讓您放棄所做的變更,並離開 BIOS 程式。 Save Changes and Reset 本項目可以在儲存變更後重啟系統。 Discard Changes and Reset 本項目可以放棄所做的變更,並重啟系統。 Save Changes 本項目可以儲存變更。 Discard Changes Discard changes done so far to any of the setup options.
Boot Override 這些項目會顯示可用的裝置。顯示在畫面中的裝置則是根據安裝在系統裡的裝置而 定,點選任一個項目可以設定該項目裡所列裝置的開機順序。 5-72 第五章:BIOS 程式設定
安裝驅動程式 在本章節中將介紹伺服器內的相關驅動程式的安裝與設 定說明。 6
6.1 安裝應用程式與工具程式 本驅動及公用程式光碟裡提供您主機板相關的驅動程式、管理應用程式與工具程 式,可以讓您將主機板功能最佳化。 ‧ 驅動及公用程式 DVD 光碟裡的內容如有變更,恕不另行通知。請造 訪華碩網站(tw.asus.com)以更新最新的軟體與工具程式。 ‧ 驅動及公用程式 DVD 光碟支援 Windows® Server 2016 與 Windows® Server 2019。 在驅動及公用程式 DVD 光碟的主選單裡有以下幾個標籤頁: 1. Drivers - 驅動程式主選單提供了您目前需要安裝的一些硬體驅動程式。 2. Utilities - 工具軟體選單顯示了可安裝於此系統的應用軟體與工具。 3. Manual - 使用手冊選單提供您使用手冊的開啟連結。 您需要在作業系統中使用網路瀏覽器軟體才能開啟使用手冊。 4.
附錄 本附錄為提供您參考的相關聯絡資訊。
Z12PP-D32 架構圖
服務與支援 請造訪 https://www.asus.