RS720-E10-RS12 2U 機架式服務器 用戶手冊
C22369 2.00 版 2023 年 8 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項............................................................................................................................... vii 用電安全....................................................................................................................................... viii 電磁安全............................................................................................................................ viii 靜電元件........................................................................................
目錄 2.6.5 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至轉接卡支撐架...............2-39 2.6.6 安裝以太網擴展卡至轉接卡支撐架.........................................................2-44 2.6.7 安裝 GPU 卡(選配).................................................................................2-45 2.6.8 安裝華碩 PIKE II 卡.......................................................................................2-55 2.6.9 安裝 M.2(NGFF)擴展卡........................................................................2-59 2.6.10 設置擴展卡.........................................
目錄 5.3.2 System Date [Day xx/xx/xxxx].............................................................. 5-9 5.3.3 System Time [xx:xx:xx]............................................................................... 5-9 5.4 Ai Tweaker 菜單(Ai Tweaker menu)..............................................................5-10 5.5 高級菜單(Advanced menu)................................................................................5-11 5.5.1 OffBoard SATA 控制器設置..............................................................
5.12 工具菜單(Tool menu).........................................................................................5-70 5.13 退出 BIOS 程序(Exit)..........................................................................................5-71 第六章:安裝驅動程序 6.1 安裝應用程序與工具程序............................................................................................ 6-2 附錄 Z12PP-D32 架構圖...............................................................................................................A-2 服務與支持.....................
使用注意事項 操作服務器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照用戶手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 服務器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用服務器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項外圍設備是否都已經連接妥當再啟動。 ‧ 避免邊吃東西邊使用服務器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近服務器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入服務器機件內,以避免引起機件短路,或是電路損毀。 ‧ 服務器啟動一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除外圍設備時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移服務器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的數據線之前,請先拔掉連接的電源線,或是先安裝數據線 之後再安裝電源線。 ‧ 使用一隻手拆裝數據線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊生成。 ‧ 服務器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、內存、主板、擴展卡、磁盤、硬盤等設備,是由許多精密的集成電路與其 它元件所構成,這些集成電路很容易因為遭受靜電的影響而損壞。因此,在拆裝任何 元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝服務器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與服務器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸服務器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜電袋上,
關於本用戶手冊 本用戶手冊主要是針對有經驗且具有個人電腦硬件組裝知識的用戶所撰寫的。本手 冊可以幫助您創建起最新、功能強大的 RS720-E10-RS12 華碩服務器。手冊內容介 紹本產品各部份元件的拆裝、設置,因此,部份元件可能是選購配備,並未包含在您 的產品當中,假如您有需要選購該配備,請向本公司授權經銷商咨詢。 章節說明 本用戶手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖標帶您認識華碩服務器的功能及特色,包括系統的前、後面板以及 內部功能的介紹。 第二章:硬件安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本服務器裡 頭。 第三章:高級安裝 本章提供您本服務器的機架安裝及使用方法。 第四章:主板信息 本章提供您有關本服務器內置主板的相關信息,包括主板的結構圖、Jumper 設置 以及連接端口位置等。 第五章:BIOS 程序設置 本章提供您本服務器之 BIOS 的升級與管理及 BIOS 設置的相關信息。 第六章:安裝驅動程序 本章節將提供您相關驅動程序的安裝與說明。 華碩 RS720-E10-RS12 用戶手冊 ix
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主板元件。不當的動 作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照用戶手冊所描述之方式 完成一項或多項軟硬件的安裝或設置。 說明:小祕訣,名詞解釋,或是進一步的信息說明。提供有助於完成某 項工作的訣竅和其他額外的信息。 哪裡可以找到更多的產品信息 您可以通過下面所提供的兩個渠道來獲得您所使用的華碩產品信息以及軟硬件的升 級信息等。 1. 華碩網站 您可以到 http://w3.asus.com.cn 華碩電腦互聯網,來取得所有關於華碩軟硬件產 品的各項信息。 2. ASUS Control Center(ACC)用戶手冊 本用戶手冊介紹如何設置並使用華碩伺服器管理工具,請至 asuscontrolcenter. asus.
電子電器產品有害物質限制使用標示要求:圖中之數字為產品之環保 使用期限。僅指電子電器產品中含有的有害物質不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 30 產品中有害物質的名稱及含量: 部件名稱 有害物質 六價鉻 鎘 (Cd) (Cr(VI)) 鉛 (Pb) 汞 (Hg) x o o 印刷電路板及其 電子組件 外部信號連接頭 及線材 外殼 軟驅 電池 光驅 散熱設備 電源適配器 硬盤 中央處理器與內 存 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o x o o o o o o x x x x x x o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o x o o o o o 本表格依據 SJ/T 11364 的規定編制。 ○: 表示該有害物質在該部件所有均質材料中的含量均在 GB/T 26572 規定的限量 要求以下。 ×: 表示該有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 規定 的限量要求
xii
第一章: 系統導覽 本章將介紹本服務器的各項組成元件,其中包括系統的 前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下為本服務器包裝內的組件。 標準元件 機種型號 RS720-E10-RS12 機箱 華碩 R2P-B 2U 機架式機箱 主板 華碩 Z12PP-D32 服務器主板 硬件元件 1 x 80PLUS 電源(PSU) 12 x 可熱插拔 2.5 / 3.5 英寸存儲設備抽取架 1 x 3.5 英寸存儲設備背板 1 x 前側 I/O 面板 1 x 前側 USB3 面板 4 x 轉接卡 4 x 系統風扇 配件 1 x 驅動與應用程序光盤 螺絲一包 2 x 處理器散熱片 2 x AC 電源線 1 x 外接風扇模塊(選配) 1 x OCP3.
1.
1.3 產品規格表 華碩 RS720-E10-RS12 是一款精心打造的 2U 服務器,內裝 Z12PP-D32 服務器 主板,支持第三代 Intel® Xeon® Scalable 處理器,並包含最新單芯片系統所提供的相 關技術。 機種型號 RS720-E10-RS12 中央處理器 / 系統總線 2 x Socket P+(LGA 4189) 第三代 Intel® Xeon® Scalable 處理器 核心邏輯 Intel® C621A 芯片 總插槽數 32(每個 CPU 8 通道;每個 CPU 16 個內存條) 擴展容量 最高可擴展達 6TB 內存類型 內存 內存大小 DR4 3200 / 2933 / 2666 RDIMM/LRDIMM/3DS D LRDIMM * 請參考華碩官方網站 w3.asus.com.
機種型號 存儲設備 RS720-E10-RS12 SAS 控制器 碩 PIKE II 3008 8 接口 SAS 12Gb/s HBA 卡 華 華碩 PIKE II 3108 8 接口 SAS HW 12Gb/s RAID 卡 前側插槽 12 x 可熱插拔 2.5 / 3.5 英寸存儲設備插槽: 8 x NVMe/SATA*/SAS* + 4 x SATA*/SAS* I = 內置 A 或 S = 可熱 插拔 * 支持 12 x SATA/SAS 搭載 PIKE II 3008-8i/3108-8i/16PD (插槽 4) * 支持 tri-mode 卡(僅插槽 9-12) ** SAS 僅支持選配 SAS HBA/RAID 卡 存儲設備插槽 後側插槽(選配): 2 x 可熱插拔 2.
RS720-E10-RS12 機種型號 開關與 LED 指示燈 後面板開關 / 指示燈: 1 x Q-Code / Port 80 LED 指示燈 1 x 電源開關含指示燈 1 x Location 開關含指示燈 安全防護 TPM-SPI PFR Windows® Server RedHat® Enterprise Linux SuSE® Linux Enterprise Server CentOS Ubuntu VMware 支持操作系統 * 管理解決方案 部遠端遙控硬 外 件 軟件 請參考華碩官方網站 http://w3.asus.com.cn 以查詢最新的 操作系統支持版本 內置 ASMB10-iKVM ,支持 KVM-over-IP 的方式 ASUS Control Center(Classic) 安裝認證標準 BSMI、CE、CB、FCC(ClassA) 尺寸(深 x 寬 x 高) 淨重(不包含處理器、內存與存儲 設備) 毛重(不包含處理器、內存、存儲 設備;包含外包裝) 840 mm x 449 mm x 88 mm(2U) 25.
1.4 前面板 本服務器的前面板提供了簡單的存取功能,包括相關的 LED 指示燈、USB 接口 等,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7 顯示燈號說明。 USB 3.2 Gen 1 連接端口 插槽 1 插槽 4 插槽 7 插槽 10 前面板 LED 指示燈與按鈕 1 2 3 4 RESET 拉柄 插槽 2 插槽 3 插槽 5 插槽 6 插槽 8 插槽 9 插槽 11 插槽 12 拉柄 ‧ 插槽 1 至 8 默認支持 NVMe / SATA / SAS 硬盤設備,SAS 硬盤則 需搭配選配的華碩 PIKE II 卡使用。 ‧ 插槽 9 至 12 默認支持 SATA / SAS 硬盤設備(支持 tri-mode 卡),SAS 硬盤則需搭配選配的華碩 PIKE II 卡使用。 ‧ 所有插槽皆支持 2.5/3.
1.5 後面板 後面板包含了所有連接設備的接口、輸出/輸入連接端口與系統電源插孔等。下圖 即為服務器後面板圖標。 標準機種 / GPU 機種 擴展卡插槽 電源模塊 電源線連接孔 電源按鈕 Q-Code 指示燈 Location 按鈕 擴展卡插槽 擴展卡插槽 選配外接風扇 (GPU 機種) 選配網絡接口 DM 管理網絡接口* USB 3.2 Gen 1 接口 顯示器接口 ‧ * 本網絡接口僅供 ASMB10-iKVM 使用。 ‧ Q-Code 指示燈以錯誤代碼提示可能的情況,以便進行疑難解決。發 生錯誤原因會依實際情況而異。 ‧ 詳細內容請參考 1.7.
標準機種搭載後端面板插槽 2 x 2.5 英寸存儲設備插槽 擴展卡插槽 電源模塊 擴展卡插槽 選配外接風扇 (GPU 機種) 電源線連接孔 電源按鈕 Q-Code 指示燈 選配網絡接口 DM 管理網絡接口* USB 3.2 Gen 1 接口 顯示器接口 Location 按鈕 擴展卡插槽 ‧ * 本網絡接口僅供 ASMB10-iKVM 使用。 ‧ Q-Code 指示燈以錯誤代碼提示可能的情況,以便進行疑難解決。發 生錯誤原因會依實際情況而異。 ‧ 詳細內容請參考 1.7.
1.6 內部組件 下圖即為本服務器的標準內部組件: 標準機種 1. 轉接卡托架 2. OCP 適配器(選配,隱藏) 3. 電源供應器(隱藏) 4. PCIe 轉接卡(隱藏) 5. 華碩 Z12P P-D32 服務器主 板 6. 系統風扇 7. NVMe/SATA/SAS 背板 8. 前端 USB 面板 9. 財產標籤(隱藏) 10. 前端面板(隱藏) 11. 12 x 2.5/3.
標準機種搭載後端面板插槽 1. 轉接卡托架 2. OCP 適配器(選配,隱藏) 3. 2 x 2.5 英寸存儲設備插槽 4. 電源供應器(隱藏) 5. PCIe 轉接卡(隱藏) 6. 華碩 Z12PP-D32 服務器主板 7. 系統風扇 8. NVMe/SATA/SAS 背板 9. 前端 USB 面板 10. 財產標籤(隱藏) 11. 前端面板(隱藏) 12. 12 x 2.5/3.
GPU 機種 1. 轉接卡托架 2. OCP 適配器(選配,隱藏) 3. 電源供應器(隱藏) 4. PCIe 轉接卡(隱藏) 5. 華碩 Z12PP-D32 服務器主板 6. 系統風扇 7. NVMe/SATA/SAS 背板 8. 前端 USB 面板 9. 財產標籤(隱藏) 10. 前端面板(隱藏) 11. 12 x 2.5/3.5 英寸存儲設備插 槽 12.
1.7 LED 顯示燈號說明 1.7.
1.7.
1.7.
1.7.
1.7.
Action PHASE POST CODE TYPE Initialize KTI input structure 0xA1 Collect info such as SBSP, Boot Mode, Reset type 0xA3 Setup up minimum path between SBSP & other sockets 0xA6 Sync up with PBSPs 0xA7 KTI initialization Quick VGA IIO Early initialization DESCRIPTION 0xA0 0xA8 Topology discovery and route calculation Progress Program final route 0xA9 Program final IO SAD setting 0xAA Protocol layer and other Uncore settings 0xAB Transition links to full speed opeartion 0xAE Coherency S
Action Quick VGA PHASE MRC Memory initialization POST CODE TYPE DESCRIPTION 0x70 High Bandwidth Memory 0x7E Pipe Sync AP Boot Mode 0xB0 Detect DIMM Configuration 0xB1 Initialize clocks for all MemSs 0xB2 Gather SPD Data 0xB3 Early Configuration 0xB4 Check DIMM Ranks 0xB5 Parallel Mode Dispatch 0xB6 DDRIO Initialization 0xB7 DDR Training 0xB8 Initialize Throttling 0xB9 Memory Test 0xBA Memory Init 0xBB Initialize Memory Map 0xBC Set RAS Configuration 0xBD 0xBE Progress
Action Quick VGA PHASE POST CODE TYPE CPU POST-Memory Initialization 0x33 CPU Cache Initialization 0x34 Application Processor(s) (AP) Initialization 0x35 BSP Selection 0x36 CPU Initialization 0x37 Pre-memory NB Initialization 0x3B Pre-memory SB Initialization 0x4F DXE Initial Program Load(IPL) 0x60 DXE Core Started 0x61 DXE(Driver Execution Environment)phase 0x62 Progress BDS(Boot Device Selection) phase DXE NVRAM Initialization SB run-time Initialization 0x63 CPU DXE Initializati
Action PHASE Normal boot BDS(Boot Device Selection) phase POST CODE 0x9B 0x9C 0x9D 0xA0 0xA1 0xA2 0xA3 0xA8 0xA9 0xAB 0xAD 0xAE 0xAF 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 TYPE Progress DESCRIPTION AMI USB Driver Initialization AMI USB Driver Initialization AMI USB Driver Initialization AHCI Initialization AHCI Initialization AHCI Initialization AHCI Initialization BIOS Setup password verify BIOS Setup start BIOS Setup input wait Ready to Boot event Legacy Boot event Exit Boot Services Legacy Option ROM Initi
1-22 第一章:系統導覽
第二章: 硬件安裝 本章節要告訴您如何安裝及卸除本服務器各個部分的組 件,以及在安裝過程中必需注意的事項。 2
2.1 機箱上蓋 打開機箱後半部上蓋 1. 使用螺絲起子鬆開機箱兩側的 2 顆螺絲。 2. 按下機箱上的按鈕。 3. 將機箱上蓋向後推,使之鬆開脫離機箱。 4.
打開中間機箱上蓋 1. 使用螺絲起子鬆開機箱兩側的 2 顆螺絲。 2. 按下機箱上的按鈕。 3. 將機箱上蓋向後推,使之鬆開脫離機箱。 4.
2.2 導風罩 請依照以下步驟移除導風罩: 1. 使用螺絲起子鬆開固定導風罩的 4 顆螺絲。 2. 將導風罩由機箱內垂直取出。 請依照以下步驟安裝導風罩: 1. 將導風罩對齊內存插槽邊緣並安裝,使之固定於機箱內。 2.
2.3 中央處理器(CPU) 本主板具備 Socket P+ 處理器插槽,本插槽是專為第三代 Intel® Xeon® Scalable 處理器所設計。 • 在您購買本主板之後,請確認在處理器插座上附有一個 P n P 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保護 蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在 安 裝 完 主 板 之 後 , 請 將 即 插 即 用 的 保 護 蓋 保 留 下 來 。 只 有 在 S o c k e t P+ 插槽上附有即插即用保護蓋的主板符合 R e t u r n Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理 產品的維修與保修。 • 本保修不包括處理器插座因遺失、錯誤的安裝或不正確的移除即插即 用保護蓋所造成的毀損。 2.3.1 移除中央處理器與散熱器(標準機種) 請依照以下步驟移除中央處理器與散熱器(標準機種): 1. 依照 2.1 機箱上蓋 的說明移除後半部上蓋。 2. 依照 2.2 導風罩 的說明移除導風罩。 3.
4. 鬆開所有固定散熱器的螺絲,並將散熱器由主板上移除。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 5. 將散熱器翻面找到 CPU 托架,鬆開托架握把以將 CPU 取下。 托架握把 6.
2.3.2 移除中央處理器與散熱器(GPU 機種) 請依照以下步驟移除中央處理器與散熱器(GPU 機種): 1. 依照 2.1 機箱上蓋 的說明移除後半部上蓋。 2. 依照 2.2 導風罩 的說明移除導風罩。 3.
4. 鬆開所有固定散熱器的螺絲,並將散熱器由主板上移除。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 5.
6.
2.3.3 安裝中央處理器與散熱器(標準機種) 1. 依照 2.2 導風罩 的說明移除導風罩。 2. 找到主板上 CPU 插槽的位置。 3.
4. 移除主板 CPU 插槽上的 PnP 保護蓋。 5.
6. 向外側下壓散熱器四角的固定鎖,依下圖順序以順時針方向轉動固定散熱器的螺 絲 2 次,以將散熱器固定於主板。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 7. 依照 2.
2.3.4 安裝中央處理器與散熱器(GPU 機種) 1. 依照 2.2 導風罩 的說明移除導風罩。 2. 找到主板上 CPU 插槽的位置。 3.
4. 移除主板 CPU 插槽上的 PnP 保護蓋。 5.
6.
7. 將剩餘的螺絲鎖緊以將散熱器固定於主板。 Intel® 建議使用扭力值為 8 lbf-in 的螺絲起子。 8. 依照 2.
2.4 系統內存 2.4.1 概述 本主板配置有 32 組 DDR4 DIMM(Double Data Rate 4,雙倍數據傳輸率)內存 條插槽。 下圖為 DDR4 DIMM 內存條插槽在主板上之位置。 2.4.
雙顆 CPU 設置 DIMMs 2 4 8 DIMM_F1 12 16 32 • • • • • DIMM_F2 • DIMM_E1 • DIMM_E2 • DIMM_H1 • DIMM_H2 • • DIMM_G1 • • • DIMM_G2 • • DIMM_C2 • DIMM_C1 • • • • DIMM_D2 • • DIMM_D1 • DIMM_A2 DIMM_A1 • • • • • • • • DIMM_B1 • • • DIMM_P1 • • • DIMM_B2 • DIMM_P2 • DIMM_N1 • • • DIMM_N2 • DIMM_T2 • • • DIMM_R2 • • DIMM_L2 • DIMM_L1 • • • • DIMM_M2 • • DIMM_M1 • DIMM_J2 • • • • • • • DIMM_K2 2-18 第二章:硬件安裝 • • DIMM_R1 DIMM_K1 • •
若您也想安裝 PMem,請參考下表進行設置。 Channel DDR4+BPS 4+4 F E H G DIMM_F1 DIMM_F2 DIMM_E1 DIMM_E2 DIMM_H1 DIMM_H2 DIMM_G1 DIMM_G2 BPS DDR4 BPS DDR4 DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 BPS 8+4 DDR4 DDR4 BPS DDR4 DDR4 BPS 8+8 DDR4 DDR4 BPS DDR4 BPS DDR4 BPS DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 DDR4 BPS 6+1 8+1 12+2
2.4.3 安裝內存條 安裝移除內存條前,請確認已安裝中央處理器、散熱器與導風罩。 請依照下面步驟安裝內存條: 內存條缺口 1. 先將內存條插槽的固定卡扣扳開。 2. 將內存條的金手指對齊內存條插槽的 溝槽,並且在方向上要注意金手指的 缺口要對準插槽的凸起點。 插槽凸起點 往外扳開內存條插 槽的卡扣 內存插槽上的凹槽為設計只一個方向供內存條插入,請在裝入前,確定 內存條與內存插槽上的安裝方向是契合的。 3. 最後緩緩將內存條插入插槽中,若無 錯誤,插槽的卡扣會因內存條安裝而 自動扣到內存條的凹孔中。 卡扣會在內存條正確 安裝後自動扣上 請將內存條缺口對準插槽的凸起點並垂直插入,以免造成內存條缺口損 壞。 2.4.4 取出內存條 請依照以下步驟取出內存條: 1. 依照 2.1 機箱上蓋 的說明移除後端上 蓋板。 2. 壓下內存條插槽的固定卡扣以鬆開內存 條。 3.
2.5 安裝硬盤 本系統支持 12 個 2.5 / 3.5 英寸熱插拔 SATA/SAS 存儲設備。硬盤的安裝方 式,是經由裝入連接在主板 SATA/SAS 背板上的模塊式硬盤擴展槽來使用。 請按照以下的步驟,安裝 3.5 英寸熱插拔 SATA/SAS 存儲設備: 1. 請先將握把上的固定扣朝右方撥開,以便將硬盤槽握把鬆開。 握把 固定扣 2. 將握把朝外扳開時,硬盤槽便會 向外滑出,請順勢將硬盤擴展槽 往主機的前方抽離。 3. 將硬盤槽放置在平坦桌面上。 4. 取出準備安裝的存儲設備。 5.
6. 當存儲設備安裝完畢後,請以手 緊握住硬盤槽握把置入系統的 插槽中,將其輕推至機箱底部 (A),最後請將板手輕輕地推 回原位並輕扣固定,使硬盤槽能 夠緊密地固定在機箱中。 7.
請按照以下的步驟,安裝 2.5 英寸熱插拔 SATA/SAS 存儲設備: 1. 請先將握把上的固定扣朝右方撥開,以便將硬盤槽握把鬆開。 握把 固定扣 2. 將握把朝外扳開時,硬盤槽便會 向外滑出,請順勢將硬盤擴展槽 往主機的前方抽離。 3. 將硬盤槽放置在平坦桌面上。 4. 取出準備安裝的存儲設備與螺絲 配件。 5.
6. 當存儲設備安裝完畢後,請以手 緊握住硬盤槽握把置入系統的 插槽中,將其輕推至機箱底部 (A),最後請將板手輕輕地推 回原位並輕扣固定,使硬盤槽能 夠緊密地固定在機箱中。 7.
2.6 擴展插槽 本服務器已預先安裝 4 組轉接卡以支持 9 個 PCIe 插槽。 標準機種 / GPU 機種 轉接卡 4 轉接卡 2 轉接卡 1 OCP 3.0 適配器 華碩 PIKE II 卡 (選配) 轉接卡 3 標準機種搭載後端面板插槽 2 x 2.5 吋存儲設備插槽 轉接卡 2 轉接卡 3 轉接卡 1 OCP 3.
轉接卡支撐架 1 轉接卡支撐架 1 支持 PCIe Gen4 插槽 1-4。 PCIe 插槽 運行模式 插槽 1 x8 x16 插槽 2 x8 N/A 插槽 3 x16 OCP 3.0 插槽 4 x8(華碩 PIKE II 卡) x8(華碩 PIKE II 卡) 轉接卡支撐架 2 轉接卡支撐架 2 支持 PCIe Gen4 插槽 5-6。當使用 x16 卡插槽 6 卻關閉時,插 槽 5 會自動切換為 x16 模式。 PCIe 插槽 運行模式 插槽 5 x8 x16 插槽 6 x8 N/A 轉接卡支撐架 3 轉接卡支撐架 3 支持 PCIe Gen4 插槽 7。當使用 M.
2.6.1 安裝擴展卡至轉接卡支撐架 1 請按照以下步驟安裝擴展卡至轉接卡支撐架 1: 1. 鬆開固定轉接卡支撐架 1 於機箱上的指旋螺絲。 2. 使用雙手握住轉接卡支撐架 1 的兩端,再將其從主板的 PCIE 插槽中取出。 3.
4. 將轉接卡支撐架 1 以下圖所示方向擺放在平坦桌面上。 5. 撥開金屬托架鎖。 6. 安裝 PCIE 擴展卡至轉接卡支撐架 1。 7.
8. 重新連接轉接卡支撐架 1 的排線。 9. 重新安裝轉接卡支撐架 1 至主板。 10.
2.6.2 安裝擴展卡至轉接卡支撐架 2 請按照以下步驟安裝擴展卡至轉接卡支撐架 2: 1. 鬆開固定轉接卡支撐架 2 於機箱上的指旋螺絲。 2. 鬆開固定轉接卡支撐架 2 於主板上的指旋螺絲。 3. 使用雙手握住轉接卡支撐架 2 的兩端,再將其從主板的 PCIE 插槽中取出。 4.
5. 將轉接卡支撐架 2 以下圖所示方向擺放在平坦桌面上。 6. 撥開金屬托架鎖。 7. 安裝 PCIE 擴展卡至轉接卡支撐架 2。 8.
9. 重新連接轉接卡支撐架 2 的排線。 10. 重新安裝轉接卡支撐架 2 至主板。 11. 鎖上步驟 1 移除的指旋螺絲,固定轉接卡支撐架 2 至機箱。 12.
2.6.3 安裝擴展卡至轉接卡支撐架 3 請按照以下步驟安裝擴展卡至轉接卡支撐架 3: 1. 鬆開固定轉接卡支撐架 3 於機箱上的指旋螺絲。 2. 鬆開固定轉接卡支撐架 3 於主板上的指旋螺絲。 3. 使用雙手握住轉接卡支撐架 3 的兩端,再將其從主板的 PCIE 插槽中取出。 4.
5. 將轉接卡支撐架 3 以下圖所示方向擺放在平坦桌面上。 6. 撥開金屬托架鎖。 7. 安裝 PCIE 擴展卡至轉接卡支撐架 3。 8.
9. 重新連接轉接卡支撐架 3 的排線。 10. 重新安裝轉接卡支撐架 3 至主板。 11. 鎖上步驟 1 移除的指旋螺絲,固定轉接卡支撐架 3 至機箱。 12.
2.6.4 安裝擴展卡至轉接卡支撐架 4 請按照以下步驟安裝擴展卡至轉接卡支撐架 4: 1. 鬆開固定轉接卡支撐架 4 於機箱上的指旋螺絲。 2.
3. 將轉接卡支撐架 4 翻面並移除金屬擋板。 4.
5. 重新安裝轉接卡支撐架 4 至主板。 6.
2.6.5 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至轉接卡支撐架 建議您將 OCP 3.0 插槽基板安裝至轉接卡支撐架 1 上的 PCIE2 插槽。 請依照以下步驟安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至轉接卡支撐架: 1. 鬆開固定轉接卡支撐架於機箱上的指旋螺絲。 2.
3. 移除轉接卡支撐架連接的排線。 4. 移除轉接卡 PCIe 支撐架。 PCIe 支撐架 5. 安裝 OCP 3.0 支撐架至 OCP 3.
6. 將轉接卡支撐架以下圖所示方向擺放在平坦桌面上。 7. 撥開金屬托架鎖。 8. 安裝OCP 3.0 插槽基板至轉接卡支撐架上的 PCIE2 插槽。 9. 連接排線。 10. 安裝 OCP 3.0 卡後,將金屬托架鎖扣上,以將 OCP 3.
11. 重新連接轉接卡支撐架的排線。 12. 重新安裝轉接卡支撐架至主板。 13.
14. 由 PCIe 轉接卡支撐架後方將 OCP 3.0 卡安裝至 OCP 3.0 插槽(A),確認 OCP 3.
2.6.6 安裝以太網擴展卡至轉接卡支撐架 預先安裝的轉接卡支撐架可支持四端口或雙端口網絡控制器擴展卡。 若您想要安裝後側外接風扇時,請勿安裝四端口網絡控制器擴展卡。 請依照以下步驟安裝四端口或雙端口網絡控制器擴展卡: 1. 依照 2.6.4 安裝擴展卡至轉接卡支撐架 4 的步驟 1-2,由機箱上移除轉接卡支撐 架。 2. 將轉接卡支撐架翻面,安裝四端口或雙端口網絡控制器擴展卡至 PCIE_LAN1 插 槽(A),並鎖上 2 顆螺絲固定(B)。 雙端口網絡控制器擴展卡 四端口網絡控制器擴展卡 3. 依照 2.6.
2.6.7 安裝 GPU 卡(選配) 請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 1: 1. 鬆開固定轉接卡支撐架 1 於機箱上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 1 的兩 端,再將其從主板的 PCIE 插槽中取 出。 3.
4. 將轉接卡支撐架 1 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9.
10. 取出準備安裝的另一張 GPU 卡。 11. 安裝 GPU 卡至轉接卡支撐架 1。 12. 鎖上螺絲固定 GPU 導風罩。 13. 連接電源排線至 GPU 卡。 14.
15. 重新連接轉接卡支撐架 1 的排線。 16. 安裝轉接卡支撐架與 GPU 卡至 主板的 PCIE 插槽,確認轉接卡 支撐架 1 上的金手指部分已完 全沒入插槽內。 17.
請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 2: 1. 鬆開固定轉接卡支撐架 2 於機箱上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 2 的兩 端,再將其從主板的 PCIE 插槽中取 出。 3.
4. 將轉接卡支撐架 2 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9. 安裝 GPU 卡至轉接卡支撐架 2。 10.
11. 重新連接轉接卡支撐架 2 的排線。 12. 安裝轉接卡支撐架與 GPU 卡至 主板的 PCIE 插槽,確認轉接卡 支撐架 2 上的金手指部分已完 全沒入插槽內。 13.
請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 3: 1. 鬆開固定轉接卡支撐架 3 於機箱上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 3 的兩 端,再將其從主板的 PCIE 插槽中取 出。 3.
4. 將轉接卡支撐架 3 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9. 安裝 GPU 卡至轉接卡支撐架 3。 10.
11. 重新連接轉接卡支撐架 3 的排線。 12. 安裝轉接卡支撐架與 GPU 卡至 主板的 PCIE 插槽,確認轉接卡 支撐架 3 上的金手指部分已完 全沒入插槽內。 13.
2.6.8 安裝華碩 PIKE II 卡 您可以更換預先安裝的華碩 PIKE II 卡以支持使用 SAS 存儲設備。 請按照以下步驟移除預先安裝的華碩 PIKE II 卡: 1. 鬆開固定轉接卡支撐架於機箱上的指旋螺絲。 2. 使用雙手握住轉接卡支撐架的兩端,再將其從主板的 PCIE 插槽中取出。 3.
4. 將轉接卡支撐架以下圖所示方向擺放在平坦桌面上。 5. 撥開金屬托架鎖。 6. 由轉接卡支撐架上移除華碩 PIKE II 卡。 7.
請按照以下步驟安裝華碩 PIKE II 卡: 1. 取出準備安裝的華碩 PIKE II 卡。 2. 安裝華碩 PIKE II 卡至轉接卡支撐架的 PCIe 插槽。 3. 將金屬托架鎖扣上,以將華碩 PIKE II 卡固定於轉接卡支撐架。 4.
5. 重新連接轉接卡支撐架的排線。 6. 安裝轉接卡支撐架至主板。 7.
2.6.9 安裝 M.2(NGFF)擴展卡 請依照以下的步驟安裝 M.2 擴展卡(支持 2260 / 2280)至主板上的 M.2 (NGFF)插槽: 1. 依照 2.6.3 安裝擴展卡至轉接卡支撐架 3 的步驟 1-3,移除轉接卡支撐架 3。 2. 鬆開鎖定 PSU 導風罩的螺絲,並移除導風罩。 3. 找到主板上的 M.
4. 在主板上選擇欲安裝的 M.2 卡的螺絲孔位置,並鎖上螺絲座。 5. 將 M.2 擴展卡對準主板上的 M.2(NGFF)插槽裝入 ,並鎖上螺絲固定。 2260 2260 2280 2280 6.
7.
2.6.10 設置擴展卡 安裝好擴展卡之後,接著須通過軟件設置來調整擴展卡的相關設置。 1. 啟動電腦,然後更改必要的 BIOS 程序設置。若需要的話,您也可以參閱第五章 BIOS 程序設置以獲得更多信息。 2. 為加入的擴展卡指派一組尚未被系統使用到的 IRQ。請參閱下表中所列出的中斷 請求(IRQ)使用一覽表。 3.
2.
預先連接的系統排線 1. 4-pin BPPWR2 電源接口(連接至背板) 2. 8-pin VGAPWR2 電源接口(連接至背板) 3. 8-pin VGA 電源接口(連接至顯卡,選配) 4. 面板連接插座(連接至前置 I/O 面板) 5. 系統風扇連接插座(主板 FAN1-4 至系統風扇) 6. Mini SAS 連接插座 7. SLMPCIE3、SLMPCIE4、SLMPCIE9、SLMPCIE10 Slim PCIe 連接插座(連接 至背板) 8. SLMPCIE1、SLMPCIE2、SLMPCIE5、SLMPCIE6、SLMPCIE7 與 SLMPCIE8 Slim PCIe 連接插座(連接至 PCIe 轉接卡) 9. USB 3.2 Gen 1連接插座(連接至前置 I/O 面板) 10. 4-pin BPPWR4 電源接口(連接至背板) 11.
2.
12 x SATA/SAS 背板連接端口 排線 連接至 MSAS_HD1 Mini-SAS HD 至 Mini-SAS HD 華碩 PIKE II 卡 MSAS_HD2 Mini-SAS HD 至 Mini-SAS HD 華碩 PIKE II 卡 MSAS_HD3* Mini-SAS HD 至 SATA7P*4 後端面板插槽 SAS HDD 與 9098 * 標準機種搭載後端面板插槽 4 x NVMe 背板連接端口 排線 連接至 SLMPCIE1 Slimline PCIe 至 Slimline PCIe 主板的 SLMPCIE3 SLMPCIE_P3/P4 Slimline PCIe 至 Slimline PCIe 主板的 SLMPCIE4 8 x NVMe 背板連接端口 排線 連接至 SLMPCIE1 Slimline PCIe 至 Slimline PCIe 主板的 SLMPCIE3 SLMPCIE_P3/P4 Slimline PCIe 至 Slimline PCIe 主板的 SLMPCIE4 SLMPCIE3 Slimline PCIe
2.9 移除系統組件 當您在安裝或移除系統設備或是替換損壞的零組件時,或許需要移除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何移除與重新安裝下列各項系統組件。 1. 系統風扇 2. 備援式電源(PSU)模塊 安裝/移除系統風扇之前,請先關閉系統電源。 ‧ 備援式電源(PSU)模塊支持熱插拔功能。 ‧ 您可能需要在安裝組件前,先移除先前安裝的組件或出廠組件。 2.9.1 系統風扇 請依照以下步驟移除系統風扇: 1. 找到要更換的系統風扇。 2.
請依照以下步驟安裝系統風扇: 1. 準備相同型號與尺寸大小的新系統風扇。 2.
請依照以下的步驟安裝後側外接風扇: 1. 請使用螺絲起子撬開插槽。 若您想要安裝後側外接風扇時,請勿安裝四端口網絡控制器擴展卡。 2. 準備好要安裝的後側外接風扇。 3.
4. 將後側外接風扇的排線連接至主板上的 REAR_FAN1 插座。 5. 將後側外接風扇對齊機箱上的螺絲孔。 6.
2.9.2 備援式電源(PSU)模塊 您可依照以下的步驟,更換損壞的備援式電源(PSU)模塊: 1. 握住電源(PSU)模塊上的拉把。 握把 2. 握住電源(P S U)上的握把,然後使 用拇指將右側的固定閂朝左推讓電 源(P S U)鬆脫。接著可以將此電源 (PSU)模塊,從機箱中拉出。 握把 固定閂 3.
2-72 第二章:硬件安裝
第三章: 高級安裝 本章節要告訴您,如何使用滑軌套件將本服務器安裝至 機架中,以及在安裝過程中必須注意的事項。 3
3.
3.2 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1. 找到如下圖所示位於服務器上的位置,並於兩側裝上固定閂(一邊一個,並各鎖 上二顆螺絲固定)。 螺絲孔安裝的位置可能會因您鎖使用的服務器機型而有所不同,請參考 服務器用戶手冊上的說明。 2.
3. 使用包裝內附的螺絲將滑軌鐵件安裝至滑軌上。 4. 上推彈簧鎖( ),然後將螺栓插入已選定在機架上的方形安裝孔。 5. 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 6. (可選擇)可使用附件裡的滑軌螺絲以及滑軌墊圈( 上兩顆套上此墊圈的螺絲以進行固定。 ),將滑軌前後端各鎖 7. 接著請重複前面的步驟 3 至 5,安裝另一側的滑軌。 請確認安裝的機架滑軌(左、右)有平行一致,且安穩地固定在定位。 8.
3.3 滑軌尺寸 43.6mm 900mm 43.
3.4 滾珠軸承機架安裝套件 滑軌套件包含了以下組件: 2 x 1200 mm 機架滑軌(或 2 x 1000 mm 機架滑軌) 滑軌前端 機架滑軌 滑軌後端 4 x #6-32X4L 螺絲 4 x M4X4L 螺絲 8 x ø17.1 螺絲 8 x #10-32 螺絲 (或 10 x #10-32 螺絲供 1000 mm 機 架滑軌使用) 2 x M5X20L 螺絲 ‧ 隨附的螺絲會因需求而異,並非所有螺絲均為必備。 ‧ 以上套件規格若有變更,恕不另行通知。 3.4.1 選擇滑軌機櫃 請參考以下說明為服務器系統選擇適當的滑軌機櫃。 Keep-out Zone for Rail A = 700.3 mm(27.6)~965.5 mm (38”) 1200 mm 機架滑軌不含 CMA A = 700.3 m m(27.6”)~965.5 mm (38”) A + B > 1025 mm(40.4”) Rear Mounting Flange Cabinet Depth A + B > 1125 mm(44.
3.4.2 安裝機架滑軌 ‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈推薦至少需要兩位身強體壯的人來運行這部份的安裝操作。 ‧ 如有必要,推薦使用適當的起重工具以輔助吊裝。 ‧ 本節步驟以 1200 mm 機架滑軌為例,1000 mm 機架滑軌的安裝步 驟幾乎相同。 ‧ 本節圖示僅供參考。 請依照以下步驟,將機架滑軌安裝至機架上: 1. 選擇所需的空間和適當的機架滑軌 (左和右)放在機架的相對位置上。 1U 在這 1U 的空間裡面要有三 個方形安裝孔與在上方與底 部包含二個薄型的間隔,如 下圖圈選處。 2.
3. 按壓彈簧鎖,然後將滑軌後端螺栓插 入已選定在機架上的方形安裝孔。 後端機架 彈簧鎖 滑軌後端 4. 將中間滑軌向外滑動直到停止。 中間滑軌 外滑軌 5. 將內滑軌向外滑動直到停止。向外滑動固定扣以移除內滑軌。 中間滑軌 內滑軌 藍色膠片 白色膠片 僅 1200mm 機架滑軌才有藍色膠片,可用於延長或收回中間滑軌。 6.
7. 移除機箱左右兩側的 3 顆螺絲,接著移除金屬板。 下圖僅顯示機箱的一側,另一側機箱的螺絲會在相同位置。 金屬板 8. 將內滑軌對準服務器兩側的結點進行安裝,並朝服務器後端滑動以固定。 2 1 9.
10. 抬起服務器並裝入機架滑軌。 2 1 11. (選配)使用 M5X20L 螺絲將滑軌 固定於機架上。 前端機架 滑軌前端 12.
3.5 理線架(僅供 1200 mm 機架滑軌選配) 您可以額外安裝理線架(C M A)來幫助收納及配置服務器的纜線。理線架設計為 可移動式元件,方便您依機架滑軌移動服務器而不必移動理線架。 外側連接器 內側連接器 勾環綁帶 樞軸連接器 信號線綁帶 3.5.1 安裝理線架 請依照以下步驟安裝理線架: 1. 安裝機架滑軌。 請參考 3.1 滑軌套件 的說明安裝機架滑軌。 2.
3. 將理線器上的 3 個連接器對齊機架滑軌上的連接器。 中間滑軌連接器 樞軸連接器 內滑軌連接器(隱藏) 內側連接器 中間滑軌連接器 外側連接器 本章節的安裝步驟以左樞軸為例,右樞軸的安裝步驟極為相似。 4. 將內滑軌連接器連接至理線架 上的內側連接器。 5.
6. 將另一端的中間滑軌連接器連接至理線架上的樞軸連接器。 7.
3-14 第三章:高級安裝
第四章: 主板信息 在本章中要告訴您在安裝系統元件時所必須完成的主板 安裝程序。詳細內容有:頻率開關設置、跳線選擇區設置 以及主板的各種設備接口。 4
4.
主板的各項元件 跳線選擇區 頁碼 1. Clear RTC RAM (3-pin CLRTC1) 4-5 2. VGA controller setting (3-pin VGA_SW1) 4-6 3. Baseboard Management Controller setting (3-pin BMC_EN1) 4-6 4. DMLAN setting (3-pin DM_IP_SEL1) 4-7 5. IPMI SW setting (3-pin IPMI_SW1) 4-7 6. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-8 7. DDR4 Thermal Event jumper (3-pin DIMMTRIP1-2) 4-8 8. ME firmware force recovery setting (3-pin ME_RCVR1) 4-9 9. PCH_MFG1 setting (3-pin PCH_MFG1) 4-9 內部指示燈 頁碼 1.
4-4 內部連接插槽 頁碼 14. System panel connector (10-1 pin SYS_PANEL1; 14-1 pin SYS_ PANEL2) 4-20 15. Hard disk activity LED connector (4-pin HDLED1) 4-21 16. VPP_I2C connector (10-1 pin VPP_I2C1) 4-22 17. BMC Debug UART connector (3-pin BMC_DEBUGUART1) 4-22 18. CPLD JTAG1 connector (6-pin CPLD_JTAG1) 4-23 19. Liquid connector (12-1 pin LIQUID_CONN1) 4-23 20. System Management Bus (SMBUS) connector (5-1 pin SMBUS1) 4-24 21.
4.2 跳線選擇區 1.
2. VGA 控制器設置(3-pin VGA_SW1) 您可以通過本功能的設置來開啟或關閉主板內置之 V G A 圖形顯示控制器功 能。默認值為 [1-2](開啟 VGA 功能)。 3.
4. DMLAN 設置(3-pin DM_IP_SEL1) 本跳線帽提供您選擇 DMLAN 設置。設置為 [2-3] 以強制 DMLAN IP 使用固 定模式(IP=10.10.10.10, submask=255.255.255.0)。 5.
6. Smart Ride Through(SmaRT)設置(3-pin SMART_PSU1) 本跳線帽提供您啟用或關閉 Smart Ride Through(SmaRT)功能。本功能預 設為啟用。設置為 [2-3] 以關閉本功能。當本功能開啟時,SmaRT 允許電源不足 時系統不間斷運行。 7.
8. ME 固件強制恢復設置(3-pin ME_RCVR1) 這組跳線帽提供您當 Intel Management Engine(ME,管理引擎)固件發生損 壞時,可以快速恢復。 9.
4.3 內部指示燈 1. 電力指示燈(SBPWR1) 當主板上內置的電力指示燈(S B P W R1)亮著時,表示當前系統是處於正常 運行、省電模式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您 在安裝或移除任何的硬件設備之前,都必須先移除電源,等待警示燈熄滅才可進 行。請參考下圖所示。 2.
3. 信息指示燈(MESLED1) 當這個內置的指示燈亮紅燈時,為發生一個 BMC 事件記錄。 4.
5.
4.4 元件與外圍設備的連接 1. Mini-SAS HD 接口(ISATA1-2; ISSATA1) 本主板內置 mini Serial Attached SCSI(SAS)HD 接口,支持 Serial ATA。每 個接口最多支持 4 個設備。 2.
3. USB 2.0(10-1 pin USB78) 這些插槽可用來連接 USB 2.0 接口。將 USB 擴展套件連排線連接到 USB34, 然後將擴展套件安裝到機箱背部的一個空置插槽位置。這些 USB 擴展套件排線 插槽支持 USB 2.0 規格,傳輸速率高達 480 Mbps。 USB 模塊為選購配備,請另行選購。 4. USB 3.2 Gen 1 連接插槽(U31G1_34; Type-A USB3_1) 這個插槽用來連接 USB 3.2 Gen 1 模塊,可在前面板或後側接口擴展 USB 3.2 Gen 1模塊。當您安裝 USB 3.2 Gen 1 模塊,您可以享受 USB 3.2 Gen 1 的益 處,包括有更快的數據傳輸率最高達 10 Gb/s、對可充電的 USB 設備更快的充 電速度、最佳化能源效率,以及與 USB 2.
5. 機箱開啟警示連接排針(2-pin INTRUSION1) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外,尚須搭 配一個外接式檢測設備,譬如機箱開啟檢測感應器或者微型開關。在本功能啟用 時,若您有任何移動機箱元件的動作,感應器會隨即檢測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機箱開啟事件。默認設置為 CASEOPEN 與 GND 接腳短路,此功能關閉。 6.
7. 系統風扇插座(8-pin FRNT_FAN1-4; 6-pin REAR_FAN1-2) 這些插座為支持連接 0.8A–1.0A(最大 12 W)或總合 6.4 A–8.0 A(最大 96 W)的 +12V 冷卻風扇使用。將風扇電源線連接到主板上的風扇插座,請確 認黑線需接到風扇電源插座上的接地端(GND)。連接風扇電源插座時,一定要 注意到極性問題。 千萬要記得連接風扇的電源,若系統中缺乏足夠的風量來散熱,那麼很 容易因為主機內部溫度逐漸昇高而導致死機,甚至更嚴重者會燒毀主板 上的電子元件。 8.
9. M.2(NGFF)插槽(NGFF1-2) 本插槽提供安裝一個 M.2 設備。 此插槽支持 2260/2280 類型的 PCI-E 存儲設備。 M.2(NGFF)設備為選購配備,請另行選購。 10.
11. VGA 電源插座(8-pin VGAPWR1, VGAPWR3, VGAPWR4, BPPWR1) 這些插座供連接顯卡的電源(PSU)使用。電源(PSU)只能以單一方向安裝 至 VGA 電源插座。安裝時請確認電源(PSU)確實安裝且方向正確。 請勿將後側面板連接至此插座,否則會使系統發生錯誤,並對主板或設 備造成永久損壞。 12.
13. Micro SD 存儲卡插槽(MSD1) 主板支持 SD 存儲卡 v2.00(SDHC) / v3.
14.
• Locator 按鈕/開關(BMCLOCBTN#) 這組排針為連接前面板 Locator 按鈕。這個按鈕按下後 Locator 指示燈將會亮 燈。 • 硬盤動作指示燈號接針(HDLED) 這組排針可連接到電腦主機面板上的硬盤動作指示燈,一旦硬盤有存取動作 時,指示燈隨即亮起。 15.
16. VPP_I2C1 連接插槽(10-1 pin VPP_I2C1) 這個插槽供 Intel VMD 功能與感應器讀取使用。 17.
18. CPLD JTAG 插槽(6-pin CPLD_JTAG1) 本插槽可用以刻錄 CPLD JTAG。 19.
20. 系統管理總線連接端口(5-1 pin SMBUS1) 此連接端口控制系統與電源管理相關任務。此總線通過兩條數據線處理與設備 間的信號傳送與接收。 21.
第五章: BIOS 程序設置 B I O S 程序調校的優劣與否,和整個系統的運行性能有 極大的關係。針對自己的配備來作最佳化 BIOS 設置,可 讓您的系統性統再提升。本章節將逐一說明 BIOS 程序中 的每一項配置設置。 5
5.1 管理、更新您的 BIOS 程序 下列軟件讓您可以管理與更新主板上的 BIOS 設置。 1. ASUS CrashFree BIOS 3 當 BIOS 程序毀損時,使用可啟動的 U 盤來更新 BIOS 程序。 2. ASUS EzFlash 使用 U 盤更新 BIOS。 3. BUPDATER 使用可啟動的 U 盤在 DOS 環境下更新 BIOS 程序。 上述軟件請參考相關章節的詳細使用說明。 推薦您先將主板原始的 BIOS 程序備份到可啟動的 U 盤中,以備您往後 需要再次安裝原始的 BIOS 程序。使用華碩在線更新(ASUS Update) 程序來拷貝主板原始的 BIOS 程序。 5.1.
5.1.2 使用華碩 EzFlash 更新程序 華碩 EzFlash 程序讓您能輕鬆的更新 BIOS 程序,可以不必再通過啟動盤的冗長程 序或是到 DOS 模式下運行。 請至華碩網站 http://w3.asus.com.cn 下載最新的 BIOS 程序文件。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 文件的 U 盤插入 USB 接口。 2. 進入 BIOS 設置程序。來到 Tools 菜單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUSTek. EzFlash Utility Current Platform Platform : Z12PP-D32 Version : 0215 Build date: 12/13/2020 New Platform Platform : Z12PP-D32 Version : 0401 Build date: 02/09/2021 FS0 FS1 [Up/Down/Left/Right]:Switch [Enter]:Choose [q]:Exit 3.
5.1.3 BUPDATER 工具程序 以下的 BIOS 畫面只能參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程序可以提供您在 DOS 環境下,使用存儲有更新的 BIOS 文件的 U 盤來更新 BIOS 文件。 更新 BIOS 文件 請依照以下的步驟,使用BUPDATER 工具程序來更新 BIOS 文件: 1. 請先訪問華碩網站(w3.asus.com.cn)下載最新主板的 BIOS 文件。並將文件存 儲至可啟動的 U 盤內。 2. 然後將華碩支持網站(s u p p o r t.a s u s.c o m)上的 B U P D A T E R 工具程序 (BUPDATER.exe),下載並存儲至同一個可啟動的 U 盤內。 3. 將系統啟動至 DOS 環境下,然後使用鍵盤輸入命令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 U 盤裡頭的最新或原本 BIOS 文件名稱,然 後按 鍵。 A:\>BUPDATER /i[file name].
4. 程序會進行檢查文件,然後開始更新 BIOS 文件。 ASUSTek. EzFlash Utility Current Platform Platform : Z12PP-D32 Version : 0215 Build date: 12/13/2020 Start Programming Flash. New Platform Platform : Z12PP-D32 Version : 0401 Build date: 02/09/2021 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程序文件時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程序會回到 DOS 畫面,請重新啟動系統,通過硬盤啟動。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS720-E10-RS12 用戶手冊 5-5
5.2 BIOS 程序設置 主板擁有一片可編輯的固件芯片,您可以依照 5.
5.2.1 BIOS 程序菜單介紹 菜單項目 設置值 功能表列 一般說明 操作功能鍵 5.2.
5.2.3 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 菜單的項目。 點擊菜單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子菜單 在菜單畫面中,若功能選項的前面有一個小三角形標記,代表此為子菜單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子菜單。 5.2.5 操作功能鍵說明 在菜單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。 5.2.7 設置值 這些存在於菜單中的設置值是提供給用戶選擇與設置之用。這些項目中,有的功能 選項只為告知用戶當前運行狀態,並無法更改,那麼此類項目就會以淡灰色顯示。而 可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表這是可 更改的項目。 5.2.
5.3 主菜單(Main) 當您進入 BIOS 設置程序時,首先出現的第一個畫面即為主菜單,內容如下圖。 5.3.1 System Language [English] 設置系統使用語言。 5.3.2 System Date [Day xx/xx/xxxx] 設置您的系統日期。 5.3.
5.4 Ai Tweaker 菜單(Ai Tweaker menu) 本菜單可讓您設置超頻功能的相關選項。 Ai Overclock Tuner [Auto] 設置值有:[Auto] [Manual] [OC Tune] 以下項目只有在 Ai Overclock Tuner 設置為 [Manual] 時才會出現。 BCLK Frequency [100.0] 您可以使用 <+> 與 <-> 鍵調整數值。數值更改範圍由 80.0MHz 至 300.
5.5 高級菜單(Advanced menu) 在高級菜單(Advanced menu)裡的項目,為提供您更改 CPU 與其他系統設備的 設置。 請注意當更改高級菜單(Advanced menu)裡的項目時,在字段中輸入不 正確的數值將會導致系統運行不正常。 Core Optimizer [Disabled] 啟用本項目使處理器運行最高頻率。設置值有:[Disabled] [Enabled] 5.5.
5.5.2 Trusted Computing Security Device Support [Enabled] 可讓您啟動或關閉 BIOS 安全設備支持功能。設置值有:[Disabled] [Enabled] 5.5.3 ACPI 設置 Enable ACPI Auto Configuration [Disabled] 本項目為啟用或關閉 BIOS ACPI 自動設置。設置值有:[Disabled] [Enabled] 5.5.
IP Mask address 本項目可以設置 IP 網絡遮罩地址。 IP Port 本項目可以設置 IP 端口。 5.5.
以下項目只有在 LAN Enable 設置為 [JumperState] 時才會出現。 ROM Type [PXE] 提供您選擇 LAN ROM(Intel 網絡隨選只讀內存)類型。設置值有:[Disabled] [PXE] [iSCSI] Intel I350 LAN2 LAN Enable [JumperState] 提供您啟用或關閉 Intel 網絡。設置值有:[Disabled] [JumperState] 以下項目只有在 LAN Enable 設置為 [JumperState] 時才會出現。 ROM Type [Disabled] 提供您選擇 Intel LAN ROM(Intel 網絡隨選只讀內存)類型。設置值有: [Disabled] [PXE] [iSCSI] Intel I350 LAN3 LAN Enable [JumperState] 提供您啟用或關閉 Intel 網絡。設置值有:[Disabled] [JumperState] 以下項目只有在 LAN Enable 設置為 [JumperState] 時才會出現。 ROM Type [Disabled] 提供您選擇 Intel
5.5.
Parity [None] 一個 parity(同位)位能發送數據位來檢測一些傳輸錯誤,[Mark] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位為 0,表示 N 個位裡,1 出現的總次數為偶數。 [Odd] 同位位為 0,表示 N 個位裡,1 出現的總次數為奇數。 [Mark] 同位位總是 1。 [Space] 同位位總是 0。 Stop Bits [1] Stop bits 為串行數據封包的終點(開始位表示起始)。標準設置是 1 Stop bit。使用較慢的設備通信可能會需要超過 1 stop bit。設置值有:[1] [2] Flow Control [None] F l o w c o n t r o l(流量控制)能預防在緩衝區溢滿時的數據流失。當傳送數據 時,若接收的緩衝區已經滿了,此時會送出“stop”(停止)信號來停止傳送數 據流(data flow)。當緩衝區空出時,會再送出“start”(開始)信號以重新開 始傳送數據流。硬件流量控制使用兩條金屬線來傳送 start/stop(開始/停止)信 號。設置值有:[No
S e r i a l P o r t f o r O u t-o f-B a n d M a n a g e m e n t/W i n d o w s E m e r g e n c y Management Services (EMS) Settings Console Redirection EMS [Enabled] 啟用或關閉控制面板轉向功能。設置值有: [Disabled] [Enabled] 當 Console Redirection 設置為 [Enabled] 時,以下的項目才會顯示。 Console Redirection Settings Out-of-Band Mgmt Port [COM1] 經由串口來遠端遙控管理 Windows Server 系統。設置值有:[COM1] [COM2] Terminal Type [VT-UTF8] 此為微軟 Windows Emergency Management Services (EMS) 提供 Windows S e r v e r 操作系統可以通過串口來採用遠端遙控管理。設置值有:V T100] [VT100+] [VT-UTF8]
5.5.7 SIO Common 設置 Lock Legacy Resources [Disabled] 本項目可以啟用或關閉 Legacy 資源鎖定。設置值有:[Disabled] [Enabled] 5.5.
5.5.
5.5.
5.5.
5.5.
5.5.
5.5.
5.5.
5.6 平台設置菜單(Platform Configuration menu) IntelRCSetup 菜單提供更改平台設置。 請注意在字段中輸入不正確的數值將會導致系統運行不正常。 5.6.
以下的項目僅當 SATA Controller 設置為 [Enabled] 時才會顯示。 Configure SATA as [AHCI] 提供您識別 SATA 接口為連接 Solid State Drive(SSD)硬盤或硬盤設備。設 置值有:[AHCI] [RAID] SATA HDD Unlock [Enable] 本項目設置為 [E n a b l e d] 時,將會開啟硬盤密碼。設置值有:[D i s a b l e] [Enable] SATA Led locate [Enabled] 本項目設置為 [E n a b l e d] 時,會附加 L E D/S G P I O 硬件。設置值有: [Disabled] [Enabled] Support Aggressive Link Power Management [Enabled] 啟用 Suport Aggressive Link Power (SALP) 管理功能。設置值有:[Disabled] [Enabled] SATA Port 0-7 Hot Plug [Disabled] 可讓您啟動或關閉 S A T A 接口 0-7 的熱插
5.6.
5.6.
5.6.
以下的項目僅當 Memory Error 設置為 [Enabled] 時才會出現。 Memory Corrected Error [Enable] 本項目可以啟用或關閉 M e m o r y C o r r e c t e d E r r o r。設置值有:[D i s a b l e] [Enable] 以下的項目僅當 Memory Corrected Error 設置為 [Enabled] 時才會出 現。 Spare Interrupt [SMI] 本項目可以選擇 Spare Interrupt。設置值有:[Disable] [SMI] [Error Pin] [CMCI] PMem CTLR Errors [Enable] 本項目可以啟用或關閉 PMem CTLR Error Reporting & Logging。設置值有: [Disable] [Enable] PMem CTLR Low Priority Error Signaling [SMI] 本項目可以設置低優先級錯誤信號。設置值有:[Disable] [SMI] [ERR0# Pin] PMem CTLR High Priori
IIO Error Enabling IIO/PCH Global Error Support [Enable] 本項目可以啟用或關閉 IIO/PCH Global Error 支持。設置值有:[Disable] [Enable] 以下的項目僅當 IIO/PCH Global Error Support 設置為 [Enabled] 時才會 出現。 Os Native AER Support [Disable] 為 AER 錯誤處理選擇 FFM 或 OS 原生。設置值有:[Disable] [Enable] IIO Error Registers Clear [Enable] 本項目可以啟用或關閉 Clear IIO Error Registers。設置值有:[Disable] [Enable] PCIe Error Enabling Corrected Error [Enable] 本項目可以啟用 & 升級錯誤 PIN 的可更正錯誤。設置值有:[Disable] [Enable] Uncorrected Error [Enable] 本項目可以啟用 & 升級錯誤 P I N 的不可更正/可還原錯誤。設
5.
5.7.
L2 RFO Prefetch Disable [Disabled] 本項目提供您開啟或關閉 L2 RFO prefetcher。設置值有:[Disabled] [Enabled] Adjacent Cache Line Prefetch [Enabled] 本項目提供您啟用或關閉 Adjacent Cache Line Prefetch 功能。設置值有: [Disabled] [Enabled] DCU Streamer Prefetcher [Enabled] 本項目為啟用或關閉 L1 數據 prefetcher。設置值有:[Disabled] [Enabled] DCU IP Prefetcher [Enabled] 本項目提供您啟用或關閉下一個基於隨著在載入記錄之上的 L1 線。設置值有: [Disabled] [Enabled] LLC Prefetch [Disabled] 本項目提供您啟用或關閉 LLC Prefetch。設置值有:[Disabled] [Enabled] DCU Mode [Normal] [Normal] 整個 DCU 使用於快取。 [Mirror-Mode]
PSMI Configuration Global PSMI Enable [Enable] 設置值有:[Disable] [Enable] [Force setup] 以下的項目僅當 Global PSMI Enable 設置為 [Enabled] 或 [Force setup] 時才會顯示。 Socket 0 Configuration PSMI Enable [Disable] 設置值有:[Disable] [Enable] 以下的項目僅當 PSMI Enable 設置為 [Enabled] 時才會顯示。 PSMI Handler Size [256K] 設置值有:[256K] [512K] [1M] PSMI Trace Region 0-4 [Disable] 設置值有:[Disable] [Enable] 5.7.
5.7.
以下的項目僅當 Volatile Memory Mode 設置為 [2LM] 時才會出現。 AppDirect cache [Disabled] 本項目用來開啟或關閉內存區域的快取。設置值有:[Disabled] [Enabled] eADR Support [Disable] 本項目用來開啟或關閉 eADR 支持。設置值有:[Disable] [Enable] [Auto] 以下的項目僅當 eADR Support 設置為 [Enable] 或 [Auto] 時才會出現。 CPU Cache Flush Mode [Parallel] 本項目可以設置 CPU Cache Flush Mode。設置值有:[Serial] [Parallel] Memory RAS Configuration 顯示並提供選項以更改內存 RAS 設置。 Correctable Error Threshold [7FFF] 本項目可以設置 Correctable Error Threshold(0x01 - 0x7fff)。 5.7.
IOU3 (IIO PCie Port 4) [x16] 本項目可以為選擇的插槽選擇 PCIe 端口拆分。設置值有:[Auto] [x4x4x4x4] [x4x4x8] [x8x4x4] [x8x8] [x16] IOU4 (IIO PCie Port 5) [x16] 本項目可以為選擇的插槽選擇 PCIe 端口拆分。設置值有:[Auto] [x4x4x4x4] [x4x4x8] [x8x4x4] [x8x8] [x16] Enable PCI-E Completion Timeout (Per-Port) [No] 本項目用來開啟或關閉 Device Control2 暫存器的 PCIe Completion Timeout。 設置值有:[Yes] [No] Sck0 RP Correctable Err [No] 僅適用於根端口。本項目用來開啟或關閉可更正錯誤時中斷。設置值有:[Yes] [No] Sck0 RP NonFatal Uncorrectable Err [No] 僅適用於根端口。本項目用來開啟或關閉非致命錯誤時中斷。設置值有:[Yes] [No] Sck0 RP Fatal Unc
Sierra Peak Memory Region Buffer Size [None] 為每個 S i e r r a P e a k 設置內存緩衝的大小。設置值有:[N o n e] [1M B] [8MB] [64MB] [128MB] [256MB] [512MB] [1GB] Port 0/DMI 設置相關 PCI Express 端口(0/1A/1B/1C/1D/2A/2B/2C/2D/3A/3B/3C/3 D/4A4B/4C/4D/5A/5B/5C/5D)。 Link Speed [Auto] 選擇此 PCIe 端口的速度。設置值有:[Auto] [Gen 1 (2.5 GT/s)] [Gen 2 (5 GT/s)] [Gen 3 (8 GT/s)] 以下的項目僅當 Link Speed 設置為 [Auto]、[Gen 2 (5 GT/s)] 或 [Gen 3 (8 GT/s)] 時才會出現。 PCI-E Port DeEmphasis [-6.0 dB] 將此 PCIe 端口解加強控制(LNKCON2 [6])。設置值有:[-6.0 dB] [-3.
MSI [Disable] 設置值有:[Disable] [Enable] PCI-E Extended Sync [No] 本項目用來開啟或關閉當 x 為 0-9 時的 Extended Sync Mode(D:x F:0 0:7Ch B:7)。設置值有:[No] [Yes] Compliance Mode [No] 本項目用來為此 PCIe 端口開啟或關閉 Compliance Mode。設置值有: [No] [Yes] EOI [Enable] 設置值有:[Disable] [Enable] Fatal Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉致命錯誤傳播至 IIO 核心錯誤邏輯。 設置值有:[No] [Yes] Non-Fatal Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉非致命錯誤傳播至 IIO 核心錯誤邏 輯。設置值有:[No] [Yes] Corr Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉可更正致命錯誤傳播至 IIO 核心錯誤 邏輯。設置值有:[No] [Yes] ACPI PME Interrupt [No] 本
ECRC Check [Disable] 本項目用來開啟或關閉 ECRC 檢查(Error Capabilities and Control Register)。設置值有:[Disable] [Enable] SERRE [Disable] 本項目用來開啟或關閉 SERRE(SERR Reporting Enable)。設置值有: [Disable] [Enable] IODC Configuration [KTI Option] 本項目用來開啟或關閉 I O D C(I O D i r e c t C a c h e)。設置值有: [KTI Option] [Auto] [Enable for Remote InvItoM Hybrid Push] [InvItoM AllocFlow] [Enable for Remote InvItoM Hybrid AllocNonAlloc] [Enable for Remote InvItoM and Remove WViLF] MCTP [Yes] 本項目用來開啟或關閉 MCTP。設置值有:[No] [Yes] Port 1A/1C/2A/4A/4C/4D/5
以下的項目僅當 Link Speed 設置為 [Auto]、[Gen 2 (5 GT/s)] 或 [Gen 3 (8 GT/s)] 時才會出現。 PCI-E Port DeEmphasis [-3.5 dB] 將此 PCIe 端口解加強控制(LNKCON2 [6])。設置值有:[-6.0 dB] [-3.
Fatal Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉致命錯誤傳播至 IIO 核心錯誤邏輯。 設置值有:[No] [Yes] Non-Fatal Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉非致命錯誤傳播至 IIO 核心錯誤邏 輯。設置值有:[No] [Yes] Corr Err Over [No] 本項目用來為此 PCIe 端口開啟或關閉可更正致命錯誤傳播至 IIO 核心錯誤 邏輯。設置值有:[No] [Yes] ACPI PME Interrupt [No] 本項目用來開啟或關閉此 PCIe 端口產生的 ACPI PME 中斷。設置值有: [No] [Yes] P2P Memory Read [Enable] 本項目可控制 Peer2Peer Memory Read Decoding。設置值有:[Disable] [Enable] PME to ACK [Enable] 為 PME_TURN_OFF 訊息後 PME_TO_ACK 的 IIO 等待設置逾時使用。設 置值有:[Disable] [Enable] PM ACPI Mode [No] 啟用本項目時
IODC Configuration [KTI Option] 本項目用來開啟或關閉 I O D C(I O D i r e c t C a c h e)。設置值有: [KTI Option] [Auto] [Enable for Remote InvItoM Hybrid Push] [InvItoM AllocFlow] [Enable for Remote InvItoM Hybrid AllocNonAlloc] [Enable for Remote InvItoM and Remove WViLF] Non-Transparent Bridge PCIe Port Definition [Transparent Bridge] 本項目用來設置 TB、NB-NTB 或 NTB-RP 端口。設置值有:[Transparent Bridge] [NTB to NTB] Imbar2 Size [22] 本項目用來設置在 NTB 主側可預取 Imbar2 尺寸。數值範圍 <12...51> 表 示 BAR 尺寸 <4KB...
CfgBar size [25] 本項目可以設置 VMD Config BAR 尺寸(in bits Min=20, Max=27),例 如 20bits=1MB、27bits=128MB。設置值有:[20] - [27] CfgBar attribute [64-bit prefetchable] 本項目可以設置 V M D C o n f i g B A R 屬性。設置值有:[32-b i t n o nprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] MemBar1 size [25] 本項目可以設置 VMD Memory BAR1 尺寸(in bits Min=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設置值有:[20] - [39] MemBar1 attribute [32-bit non-prefetchable] 本項目可以設置 VMD Memory BAR1 屬性。設置值有:[32-bit nonprefetchable] [64-bit non-prefetchable] [6
MemBar2 size [20] 本項目可以設置 VMD Memory BAR2 尺寸(in bits Min=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設置值有:[20] - [39] MemBar2 attribute [64-bit non-prefetchable] 本項目可以設置 VMD Memory BAR2 屬性。設置值有:[32-bit nonprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] VMD Config for IOU 3 Enable/Disable VMD [Enable] 本項目用來開啟或關閉 VMD。 以下的項目僅當 Enable/Disable VMD 設置為 [Enable] 時才會出現。 VMD Port A [Disable] 本項目用來開啟或關閉指定根端口的 Intel® Volume Management Device Technology 功能。設置值有:[Disable] [Enable] VMD Port B [Disable] 本項目用來開啟
MemBar1 attribute [32-bit non-prefetchable] 本項目可以設置 VMD Memory BAR1 屬性。設置值有:[32-bit nonprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] MemBar2 size [20] 本項目可以設置 VMD Memory BAR2 尺寸(in bits Min=20),例如 20bits=1MB、22bits=4MB、26bits=64MB。設置值有:[20] - [39] MemBar2 attribute [64-bit non-prefetchable] 本項目可以設置 VMD Memory BAR2 屬性。設置值有:[32-bit nonprefetchable] [64-bit non-prefetchable] [64-bit prefetchable] VMD Config for IOU 4 Enable/Disable VMD [Enable] 本項目用來開啟或關閉 VMD。 以下的項目僅當 Enable/Disable VMD 設置為 [En
VMD Config for IOU 3 Enable/Disable VMD [Enable] 本項目用來開啟或關閉 VMD。 以下的項目僅當 Enable/Disable VMD 設置為 [Enable] 時才會出現。 VMD Port A [Disable] 本項目用來開啟或關閉指定根端口的 Intel® Volume Management Device Technology 功能。設置值有:[Disable] [Enable] VMD Port B [Disable] 本項目用來開啟或關閉指定根端口的 Intel® Volume Management Device Technology 功能。設置值有:[Disable] [Enable] VMD Port C [Enable] 本項目用來開啟或關閉指定根端口的 Intel® Volume Management Device Technology 功能。設置值有:[Disable] [Enable] VMD Port D [Enable] 本項目用來開啟或關閉指定根端口的 Intel® Volume Management Device Technolo
Port 1A - 1D [Disable] 本項目用來開啟或關閉 NVMe Legacy 模式。設置值有:[Disable] [Enable] Hot Plug Capable [Disable] 本項目用來開啟或關閉 PCIe 根端口的熱插拔功能。設置值有:[Disable] [Enable] Intel® AIC Retimer/AIC SSD HW at Stack2 [Disable] 宣布 Stack2(Port2A-2D)的 Intel® AIC Retimer/AIC SSD HW。必須覆 蓋 IOU0 拆分。設置值有:[Enable] [Disable]設置值有:[Enable] [Disable] 以下的項目僅當 Intel® AIC Retimer/AIC SSD HW at Stack2 設置為 [Enable] 時才會出現。 Port 2A - 2D [Disable] 本項目用來開啟或關閉 NVMe Legacy 模式。設置值有:[Disable] [Enable] Hot Plug Capable [Disable] 本項目用來開啟或關閉 PCIe 根端口的熱插拔功能。設置值有:
以下的項目僅當 Intel® AIC Retimer/AIC SSD HW at Stack5 設置為 [Enable] 時才會出現。 Port 5A - 5D [Disable] 本項目用來開啟或關閉 NVMe Legacy 模式。設置值有:[Disable] [Enable] Hot Plug Capable [Disable] 本項目用來開啟或關閉 PCIe 根端口的熱插拔功能。設置值有:[Disable] [Enable] 5.7.
以下的項目僅當 SpeedStep (Pstates) 設置為 [Enable] 時才會出現。 Configure TDP Lock [Enable] 本項目用以設置 TDP CONTROL Lock Bit。設置值有:[Disable] [Enable] AVX P1 [Normal] 本項目用來選擇 AVX P1 等級。設置值有:[Normal] [Level 1] [Level 2] Activate SST-BF [Disable] 本項目用來開啟或關閉 SST-BF。設置值有:[Disable] [Enable] 以下的項目僅當 Activate SST-BF 設置為 [Enable] 時才會出現。 Configure SST-BF [Enable] 本項目可以允許 BIOS 設置 SST-BF 優先核心,使 SW 不必進行設置。設置值 有:[Disable] [Enable] EIST PSD Function [HW_ALL] 設置值有:[HW_ALL] [SW_ALL] Boot performance mode [Max Performance] 在操作系統切換前允許您選擇 B
Perf P-Limit Clip [1F] 可以為 Perf P-Limit 設置的最大值。 Perf P-Limit Threshold [F] 非核心頻率臨界值以上,將會觸發插槽功能並開始嘗試提升其他插槽的頻 率。 Perf P-Limit [Enable] 本項目用來開啟或關閉以 P-Limit 性能。設置值有:[Disable] [Enable] Hardware PM State Control Hardware P-States [Native Mode] 本項目可以讓您在硬件 P-States 模式間切換。 [Disable] 硬 件 依 操 作 系 統 要 求 選 擇 P-state。(Legacy P-States) [Native Mode] 硬 件 依 操 作 系 統 指 示 選 擇 P-state。 [Out of Band Mode] 硬件自主選擇 P-state。(無操作 系統指示) [Native Mode with no Legacy Support] 硬 件 依 操 作 系 統 指 示 選 擇 P-state。(無 Legacy support
Scalability [Disable] 本項目用來開啟或關閉核心性能至基於處理器最佳化的頻率縮放。設置值有: [Disable] [Enable] Native ASPM [Disabled] [Auto] BIOS 控制 ASPM。 [Enabled] OS 控制 ASPM。 [Disabled] ASPM 關閉。 CPU C State Control Enable Monitor MWAIT [Enable] 本項目用來開啟或關閉 M o n i t o r 與 M W A I T 指示。設置值有:[D i s a b l e] [Enable] CPU C1 auto demotion [Enable] 本項目用來開啟或關閉 CPU 自動降級至 C1。請重新啟動使設置生效。設置值 有:[Disable] [Enable] CPU C1 auto undemotion [Enable] 本項目用來開啟或關閉 CPU 自動降級至 C1。請重新啟動使設置生效。設置值 有:[Disable] [Enable] CPU C6 Report [Auto] 本項目用來開啟或關閉 C P U
CPU Thermal Management CPU T State Control Software Controlled T-States [Disabled] 本項目用來開啟或關閉 S o f t w a r e C o n t r o l l e d T-S t a t e s。設置值有: [Disabled] [Enabled] 以下的項目僅當 Software Controlled T-States 設置為 [Enabled] 時才會 出現。 T-State Throttle Level [Disable] 晶片內建智能溫控調頻系統。設置值有:[D i s a b l e d] [6.25%] [12.5%] [18.75%][25.0%][31.25%][37.5%][43.75%][50.0%][56.25%][62.5%] [68.75%][75.0%] [81.25%][87.5%][93.
P0 TotalTimeThreshold Low [28] 本項目用來控制 C0 和 P0 平均時間的有效窗口。 P0 TotalTimeThreshold High [3F] 本項目用來控制 C0 和 P0 平均時間的有效窗口。 SAPM Control [Enable] 設置值有:[Enable] [Disable] EET Mode [Coarse Grained Mode] [Coarse Grained Mode] 決定是否允許用戶要求的 P1 Turbo。 [Fine Grained Mode] 決定允許多少的 Turbo。 5.
5.8.
以下的項目僅當 Log EFI Status Code 項目設置為 [Enabled] 時才會出 現。 Convert EFI Status Codes to Standard Smbios Type [Disabled] 允許您開啟或關閉 EFI 狀態編碼轉變為標準 Smbios 編碼(不是所有都可以轉換) 。設置值有:[Disabled] [Enabled]。 5.8.
5.
5.9.1 系統事件記錄(System Event Log) 提供您更改 SEL 事件記錄設置。 更改選項後需重新啟動才會生效。 SEL Components [Enabled] 本項目用來開啟或關 閉 啟 動 自 檢 時 錯 誤 或 進 度 代 碼 的事 件 記 錄 。 設 置 值 有 : [Disabled] [Enabled] 僅當 SEL Component 項目設為 [Enabled] 時,以下項目才會出現。 Erase SEL [No] 本項目用來選擇如何清除 SEL。設置值有:[No] [Yes, On next reset] [Yes, On every reset] 5.9.
5.9.
Router IP Address 本項目可以設置路由器 IP 地址。 Router MAC Address 本項目可以設置路由器 MAC 地址。 Configure IPV6 support DM_LAN1 / Shared LAN IPV6 support 本項目用來開啟或關閉 IPV6 支持。設置值有:[Enabled] [Disabled] 僅當 IPV6 support 項目設為 [Enabled] 時,以下項目才會出現。 Configuration Address source [Previous State] 選擇設置的網絡通道的參數為靜態或動態。設置值有:[Previous State] [Static] [DynamicBmcDhcp] 僅當 Configuration Address source 項目設為 [Static] 時,以下項目才會 出現。 Station IPV6 address 本項目用來設置 IPV6 地址。 Prefix Length 本項目可以設置前置位長度(最多為 128)。 Configuration Router LAN1/2 Address 選擇設置
5.9.
5.10 安全性菜單(Security menu) 本菜單可以讓您更改系統安全設置,並且提供您啟用或關閉安全啟動(S e c u r e Boot)狀態與讓用戶設置系統模式(System Mode)狀態。 Administrator Password(設置系統管理員密碼) 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
User Password(設置用戶密碼) 請依照以下步驟設置用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟刪除用戶密碼(User Password): 1. 請選擇 Clear User Password 項目並按下 。 2. 在警告窗口輸入 並按下 。 5.10.
以下的項目僅當 Secure Boot Mode 設置為 [Custom] 時才會出現。 Install Default Secure Boot Keys 本項目可以載入默認的安全啟動金鑰,包括 P K(P l a t f o r m k e y)、(K E K (key-exchange key))、db(signature database)與 dbx(revoked signature database)。所有安全啟動金鑰的狀態會由未載入更改為載入。請保存並重啟系統使 更改生效。 Clear Secure Boot Keys 本項目將會刪除先前套用的的安全啟動金鑰,包括 PK(Platform key)、(KEK (key-exchange key))、db(signature database)與 dbx(revoked signature database)。所有安全啟動金鑰的狀態會由未載入更改為載入。請保存並重啟系統使 更改生效。 Key Management 本項目只當 S e c u r e B o o t M o d e 設置為 [C u s t o m] 時才會顯示,提供您修改 Se
Clear Secure Boot Keys 本項目將會刪除先前套用的的安全啟動金鑰,包括 P K(P l a t f o r m k e y)、 (KEK(key-exchange key))、db(signature database)與 dbx(revoked signature database)。所有安全啟動金鑰的狀態會由未載入更改為載入。請保存 並重啟系統使更改生效。 Save all Secure Boot Variables 本項目可以保存安全啟動政策變量的 NVRAM 內容至目標文件系統設備的根目 錄文件(EFI_SIGNATURE_LIST 數據格式)。 Enroll Efi Image 本項目可以允許 Secure Boot 模式時運行 Efi Image。註冊 PE image 的 SHA256 Hash 憑證至 Authorized Signature Database(db)。 Device Guard Ready Remove ‘UEFI CA’ from DB 由 Secure Boot DB 移除 Microsoft UEFI CA。 Restore DB defau
5.
POST Report [5 sec] 提供您設置想要的 POST(啟動自檢)回報等待時間,可選擇從 1 至 10 秒。 設置值有:[1 sec] ~ [10 sec] [Until Press ESC] 5.11.
5.
5.
Boot Override 這些項目會顯示可用的設備。顯示在畫面中的設備則是根據安裝在系統裡的設備而 定,點擊任一個項目可以設置該項目裡所列設備的啟動順序。 5-72 第五章:BIOS 程序設置
安裝驅動程序 在本章節中將介紹服務器內的相關驅動程序的安裝與設 置說明。 6
6.1 安裝應用程序與工具程序 驅動及應用程序光盤裡提供您主板相關的驅動程序、管理應用程序與工具程序,可 以讓您將主板功能最佳化。 ‧ 驅動及應用程序 DVD 光盤裡的內容如有更改,恕不另行通知。請訪 問華碩網站(http://w3.asus.com.cn)以更新最新的軟件與工具程 序。 ‧ 驅動及應用程序 D V D 光盤支持 W i n d o w s ® S e r v e r 2016 與 Windows® Server 2019。 在驅動及應用程序 DVD 光盤的主菜單裡有以下幾個標籤頁: 1. Drivers - 驅動程序主菜單提供了您當前需要安裝的一些硬件驅動程序。 2. Utilities - 工具軟件菜單顯示了可安裝於此系統的應用軟件與工具。 3. Manual - 用戶手冊菜單提供您用戶手冊的開啟鏈接。 您需要在操作系統中使用網絡瀏覽器軟件才能開啟用戶手冊。 4.
附錄 本附錄為提供您參考的相關聯絡信息。
Z12PP-D32 架構圖
服務與支持 請訪問 https://www.asus.com.