RS720-E8-RS24-ECP 伺服器 使用手冊
給使用者的說明 版權說明 ©ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項......................................................................................................viii 用電安全.................................................................................................................. ix 電磁安全........................................................................................................... ix 靜電元件........................................................................................................... ix 警告使用者.......................................
目錄 2.5 安裝硬碟機................................................................................................2-13 2.6 擴充插槽.....................................................................................................2-17 2.6.1 安裝擴充卡......................................................................................2-17 2.6.2 設定擴充卡......................................................................................2-19 2.6.3 安裝 M.2 擴充卡.................................................................
目錄 5.4.2 5.4.3 5.4.4 5.4.5 Smart Setting(智慧設定)......................................................5-11 NCT6779D Super IO 設定.........................................................5-12 內建 LAN I350 IO 設定.............................................................5-13 序列埠控制面板重新定向(Serial Port Console Redirection)..................................................................................5-14 5.4.6 APM 設定.........................................................................................5-17 5.4.
目錄 6.1.4 RAID 設定程式................................................................................ 6-3 6.2 LSI Software RAID 設定程式............................................................... 6-4 6.2.1 建立 RAID 設定............................................................................... 6-5 6.2.2 新增或檢視一個 RAID 設定.....................................................6-11 6.2.3 將虛擬磁碟初始化.......................................................................6-12 6.2.4 重新建立損壞的硬碟..............................
.5 安 裝Intel® I350-AM1/I350-AM2/I210/X540-BT2 Gigabit 網路驅 動程式.........................................................................................................7-19 7.6 安裝顯示驅動程式..................................................................................7-22 7.7 安裝 Intel® Rapid Storage Technology enterprise 4.0 程式...7-24 附錄 華碩的聯絡資訊................................................................................................
使用注意事項 操作伺服器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統 損傷甚至人體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照使用手冊指示連接妥當, 以及電源線是否有任何破損,或是連接不正確的情形發生。如有任何破 損情形,請儘速與您的授權經銷商聯絡,更換良好的線路。 ‧ 伺服器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐 蝕電子線路。 ‧ 使用伺服器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項周邊設備是否都已經連接妥當再開機。 ‧ 避免邊吃東西邊使用伺服器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近伺服器之連接器、插槽、 孔位等處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入伺服器機件內,以避免引起機件短路,或是電路損 毀。 ‧ 伺服器開機一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請 勿用手觸摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除周邊產品時請先關閉電源。 ‧
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移伺服器之前,請先確定與其連接的所有電源都已 經拔掉。 ‧ 拆裝任何元件上連接的訊號線之前,請先拔掉連接的電源線,或是先安 裝訊號線之後再安裝電源線。 ‧ 使用一隻手拆裝訊號線,以避免接觸到兩個不同電位表面造成不當的電 流突波衝擊產生。 ‧ 伺服器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長 線,最好能夠連接一台不斷電系統 UPS。 靜電元件 處理器、記憶體、主機板、介面卡、磁碟機、硬碟機等設備,是由許多 精密的積體電路與其它元件所構成,這些積體電路很容易因為遭受靜電的影 響而損壞。因此,在拆裝任何元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝伺服器之前,請您先將 身體可能帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與伺服器金屬平面部份碰觸,釋 放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸伺服器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是
關於本使用手冊 本使用手冊主要是針對有經驗且具有個人電腦硬體組裝知識的使用者所 撰寫的。本手冊可以幫助您建立起最新、功能強大的華碩伺服器。手冊內容 介紹本產品各部份元件的拆裝、設定,因此,部份元件可能是選購配備,並 未包含在您的產品當中,假如您有需要選購該配備,請向本公司授權經銷商 洽詢。 請勿將本主機板當作一般垃圾丟棄。本產品零組件設計為可回收利用。 這個打叉的垃圾桶標誌表示本產品(電器與電子設備)不應視為一般垃 圾丟棄,請依照您所在地區有關廢棄電子產品的處理方式處理。 請勿將內含汞的電池當作一般垃圾丟棄。這個打叉的垃圾桶標誌表示電 池不應視為一般垃圾丟棄。 章節說明 本使用手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖示帶您認識華碩 RS720-E8-RS24-ECP 伺服器的功能及特 色,包括系統的前、後面板以及內部功能的介紹。 第二章:硬體安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本 伺服器裡頭。 第三章:進階安裝 本章提供您本伺服器的機架安裝及使用方法。 第四章:主機板資訊 本章提供您有關本伺服器內建主機板的相關資訊,包括主機板的構造 圖、Jumper 設定以及連接
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主機板元件。不當的 動作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照使用手冊所描述之方式 完成一項或多項軟硬體的安裝或設定。 說明:小祕訣,名詞解釋,或是進一步的資訊說明。提供有助於完成某 項工作的訣竅和其他額外的資訊。 哪裡可以找到更多的產品資訊 您可以經由下面所提供的兩個管道來獲得您所使用的華碩產品資訊以及 軟硬體的升級資訊等。 1. 華碩網站 您可以到 http://tw.asus.com 華碩電腦全球資訊網,來取得所有關於華碩軟 硬體產品的各項資訊。 2.
限用物質含有情況標示 單元 鉛 (Pb) 汞 (Hg) 限用物質及其化學符號 六價鉻 鎘 (Cd) (Cr+6) 多溴聯苯 (PBB) 印刷電路板及 o o o 其電子組件 外殼 o o o o 散熱設備 o o o 電源供應器 o o o 其他及其配件 o o o 備考 1 "o" 係指該項限用物質之百分比含量未超出百分比含量基準值。 備考 2 "-" 係指該項限用物質為排除項目。 xii 多溴二苯醚 (PBDE) o o o o o o o o o o
第一章: 系統導覽 本章將介紹本伺服器的各項組成元件,其中包括 系統的前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下為本伺服器包裝內的組件。 標準元件 機種型號 RS720-E8-RS24-ECP 機殼 華碩 R20E 2U 機架式機殼 主機板 華碩 Z10PE-D16 伺服器主機板 硬體組件 1 x 800W 備援式電源供應器(80 PLUS Platinum) 1 x SAS/SATA 硬碟背板 1 x 前置面板 1 x 前置 USB 面板 1 x 電源分配面板 4 x Easy-swap 系統風扇 24 x 可熱抽換 2.5 吋硬碟擴充槽(此為隨硬碟一起出貨) 2 x 可熱抽換 2.
1.
1.3 產品規格表 華碩 RS720-E8-RS24-ECP 是一款精心打造的 2U 伺服器,內裝 Z10PE-D16 伺服器主機板,支援 Intel® LGA2011-3 架構之 Xeon® E5-2600 v3 系列中央處理器,並包含最新內建於主機板上的晶片組所提供的相關技 術。 機種型號 RS720-E8-RS24-ECP 支援處理器 / 系統匯流排 2 x Socket R3(LGA 2011-3) Intel® Xeon® E5-2600 V3 家族處理器 QPI 6.4/8.0/9.6 GT/s 核心邏輯 Intel® C612 PCH 晶片組 記憶體 擴充插槽 總插槽數 16(每個 CPU 4 通道,每個 CPU 8 DIMMs) 擴充容量 最高可擴充達 1024GB 記憶體類型 DDR4 2133 / 1866 / 1600 / 1333 RDIMM / LR-DIMM * 請參考華碩官方網站 tw.asus.
機種型號 RS720-E8-RS24-ECP 硬碟插槽 I = 內部 A 或 S = 可熱抽換 24 x 熱抽換 2.5 吋硬碟擴充槽 2 x 熱抽換 2.5 吋 SSD 硬碟擴充槽 顯示功能 顯示晶片 Aspeed AST2400 32MB 後側 I/O 插座與開關 / LED 指示燈 管理解決方案 2 2 1 4 1 1 1 x x x x x x x USB 2.0 埠 USB 3.
1.4 前端面板 本伺服器的前端面板提供了簡單的存取功能,包括 24 個 2.5 吋 Serial ATA 硬碟擴充槽,2 個 USB 2.0 連接埠,以及易於操作的按鈕和辨識的指 示燈,可以方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考“1.7.1“一節的說明。 USB 2.0 連接埠 拉柄 前面板指示燈和按鈕 24 x 2.
1.5 後端面板 後端面板包含了兩個可熱抽換 SSD 硬碟擴充槽、介面卡插槽、輸出/輸入 連接埠、Gigabit / 10G 網路埠與電源連接孔。 後端面板會因主機板的設計而提供 PS/2 鍵盤/滑鼠複合埠、USB、顯示 器與網路等連接埠,請依照主機板實際提供的為主。 管理埠* PS/2 鍵盤/滑鼠複合埠 備援式電源供應器 SSD 硬碟擴充槽 序列埠(選配) 電源線連接孔 USB 2.0 連接埠 顯示器連接埠 擴充卡插槽擋板 USB 3.
1.6 內部組件 下圖即為本伺服器的標準內部組件: 1. 2. 3. 4. 5. 備援式電源供應器 華碩 Z10PE-D16 伺服器主機板 前側系統風扇 SATA/SAS 背板(隱藏) 硬碟擴充槽(24 x 2.5 吋硬碟擴 充槽) 6. 前側面板(隱藏) 7. 2 x SSD 硬碟擴充槽 8.
1.7 LED 顯示燈號說明 1.7.
1.7.
SSD / 硬碟指示燈說明 硬碟狀態指示燈 硬碟動作指示燈 亮綠燈 電源已開啟(偵測到有 SSD / 硬碟存在) 亮紅燈 AID 硬碟失效並且應立即更換(雖有插入 SSD / 硬 R 碟但偵測錯誤) 綠色/紅色閃爍 RAID 重建正在進行 熄滅 未安裝 SSD / 硬碟 綠燈閃爍 讀取/寫入資料至 SSD / 硬碟中 1.7.
1-12 第一章:系統導覽
第二章: 硬體安裝 本章節要告訴您如何安裝及移除本伺服器各個部 分的組件,以及在安裝過程中必需注意的事項。 2
2.1 機殼上蓋 2.1.1 打開機殼後半部上蓋 1. 請將機殼後側面板朝向自己,然後鬆開後側面板上的 2 顆指旋螺絲。此 處螺絲只需鬆開,不用完全取下。 2. 使用十字螺絲起子,移除固定在左右側邊的兩顆螺絲。 3. 然後將機殼後半上蓋向後推,並使後蓋脫離機殼。 4.
2.2 導風罩 本伺服器系統提供主機板風扇導風罩,當系統運轉時,可以讓主機板獲 得良好的散熱環境。 移除導風罩 請依照以下步驟,移除導風罩: 1. 請依照 2.1 機殼上蓋 的說明操作以 移除後半部上蓋。 2. 移除固定在導風罩上的 3 顆螺絲並 放置於一旁。 3. 請小心地將導風罩朝上從機殼內取 出。 安裝導風罩 請依照以下步驟,安裝導風罩: 1.
2.3 中央處理器(CPU) 本主機板具備兩個 LGA 2011-3 處理器插槽,本插槽是專為 LGA 封裝的 Intel® Xeon E5-2600 V3 系列處理器所設計。 • 在您購買本主機板之後,請確認在處理器插座上附有一個 PnP 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保 護蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在安裝完主機板之後,請將隨插即用的保護蓋保留下來。只有 在 LGA2011-3 插槽上附有隨插即用保護蓋的主機板符合 Return Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理 產品的維修與保固。 • 本保固不包括處理器插座因遺失、錯誤的安裝或不正確的移除隨插 即用保護蓋所造成的毀損。 2.3.1 安裝中央處理器 請依照以下步驟安裝處理器: 1.
2. 用姆指按下下左側固定扳手 (A) 並將其稍向右側推(B),直到扳手 脫離固定扣並輕輕抬起固定扳手(C)。 CPU 安裝盒上的隨插即用保護蓋是用以保護插槽上的接腳之用,因此只 有在 CPU 安裝妥當之後,才可將其移除。 固定扳手 3.
4. 將左側固定扳手往箭頭方向推以抬 起安裝盒上蓋(G)。 安裝盒上蓋邊緣 請勿將固定扳手插入固定扣。 5. 握住邊緣,然後輕輕拿起安裝盒上 蓋(H)。 安裝盒 上蓋 6. 拿起 CPU。 7. 將 CPU 對準插槽,確保 CPU 上的 金三角標誌對準插槽上的上三角標 誌。 8. 小心地將 CPU 放入插槽。 CPU 只能以單一方向正確地 安裝到主板上的插槽。切記 請勿用力地將 CPU 以錯誤的 方向安裝到插槽上,這麼做 將可能導致 CPU 與插槽上的 接腳損壞。 9.
10. 推下右側固定扳手(I),確保安裝盒上蓋的邊緣被扳手固定(J)。然 後將右側固定扳手裝入固定扣底下。 當右側固定扳手插入固定扣後從安裝盒上蓋取出隨插即用保護蓋。 請將隨插即用保護蓋保留下來。只有 LGA2011-3 插槽上附有隨插即用 保護蓋的主板符合 Return Merchandise Authorization(RMA)的要求, 華碩電腦才能為您處理產品的維修與保修。 隨插即用 保護蓋 11.
12.
2.3.2 安裝 CPU 散熱器 請將散熱器依照以下的步驟安裝: 1. 將散熱器放置在已安裝好的 CPU 上方,並確認主機板上的四個安裝孔位 與散熱器的四個螺絲孔位位置相吻合。 2.
2.4 系統記憶體 2.4.1 概觀 本主機板配置有十六(16)組 DDR4(Double Data Rate 4)記憶體模組 插槽。下圖所示為 DDR4 DIMM 記憶體模組插槽在主機板上之位置。 2.4.
單顆 CPU 的設定 在單顆 CPU 的設定裡,您可以參考以下的記憶體模組安裝建議。 單顆 CPU 設置(必須在 CPU 1 上) DIMM A2 1 DIMM 1 DIMM 2 DIMM 4 DIMM 8 DIMM A1 B2 B1 C2 C1 D2 D1 P P P P P P P P P P P P P P P P 雙顆 CPU 的設定 在雙顆 CPU 的設定裡,您可以參考以下的記憶體模組安裝建議。 兩顆 CPU 設置 A2 A1 2 DIMM 4 DIMM 8 DIMM 12 DIMM 16 DIMM DIMM (CPU1) B2 B1 C2 C1 D2 D1 E2 P P P P P E1 DIMM (CPU2) F2 F1 G2 G1 H2 H1 P P P P P P P P P P P P P P P P P P P P P P P P P P P 華碩 RS720-E8-RS24-ECP 使用手冊 2-11
2.4.3 安裝記憶體模組 1. 先將記憶體模組插槽固定卡 榫扳開。 2. 將記憶體模組的金手指對齊 記憶體模組插槽的溝槽,並 且在方向上要注意金手指的 缺口要對準插槽的凸起點。 記憶體模組缺口 插槽凸起點 往外扳開記憶體 模組插槽的卡榫 記憶體插槽上的凹槽為設計僅一個方向供記憶體模組插入,請在裝入 前,確定記憶體模組與記憶體插槽上的安裝方向是契合的。 3. 將記憶體模組插入插槽中,若 無錯誤,插槽的卡榫會因記憶 體模組置入而自動扣到記憶體 模組的凹孔中。 卡榫扣入 請將記憶體模組缺口對準插槽的凸起點並垂直插入,以免造成記憶體模 組缺口損壞。 2.4.4 取出記憶體模組 1. 壓下記憶體模組插槽的固定卡榫 以鬆開記憶體模組。 2.
2.5 安裝硬碟機 本系統提供可安裝二十四(24)個 2.5 吋 Serial ATA 硬碟機,以及兩 (2)個 2.5 吋 SSD 硬碟機。 安裝 2.5 吋 Serial ATA 硬碟: 請按照以下的步驟來安裝硬碟機: 1. 請先將握把上的固定扣朝上方撥開,以便將硬碟擴充槽握把鬆開。 2. 將握把朝下扳開時,硬碟擴充槽便會向外滑出,請順勢將硬碟擴充槽抽 離主機,並將硬碟擴充槽放置在平坦的桌面上。 固定扣 硬碟擴充槽 握把 3.
4. 如右圖所示的方向,將 Serial ATA/SAS 硬碟上的螺絲孔對準擴 硬碟螺絲孔 充槽兩側的螺絲孔位置入。 硬碟 請確認硬碟機上的四個螺絲安裝 孔,已經對準擴充槽上的安裝孔 位。 擴充槽螺絲孔位 5. 接著鎖上 4 顆螺絲(一側各 2 顆 )來固定。 6. 將裝好 2.5 吋 Serial ATA/SAS 硬碟的擴充槽,對準主機上的 安裝位置推回原位並扣上固定 扣,使硬碟槽能夠緊密地固定 在機殼中。 7. 若是要安裝其他 2.5 吋 Serial ATA/SAS 硬碟機,請重複步驟 1~6 進行。 已裝妥 2.
安裝 2.5 吋 SSD 硬碟: 請依照以下步驟,安裝 2.5 吋 SSD 硬碟: 1. 按下硬碟擴充槽上的固定扣,以鬆 脫硬碟槽握把。 硬碟擴充槽握把 固定扣 2. 將握把朝外扳開時,硬碟擴充槽 便會向外滑出,請順勢將硬碟擴 充槽抽離主機。 3.
4. 如下圖所示,將 SSD 硬碟上的螺絲孔對準擴充槽兩側的螺絲孔位置入。 請確認 SSD 硬碟機上的 4 個螺絲安裝孔,已經對準擴充槽上的安裝孔 位。然後鎖上 4 顆螺絲(一側各 2 顆 )來固定。 SSD 螺絲孔 SSD 插槽螺絲孔位 5. 將裝好 2.5 吋 SSD 硬碟的擴充槽,對準主機上的安裝位置推回原位並扣 上固定扣,使硬碟槽能夠緊密地固定在機殼中。 6. 若要安裝其他 2.
2.6 擴充插槽 2.6.1 安裝擴充卡 請按照以下的步驟進行: 1. 請依照 2.1 機殼上蓋 的步驟,將機殼蓋板移除。 2. 移除 2 顆固定在金屬擋板蓋板上的螺絲。 請將螺絲放置於一旁,稍後會再使用。 3. 取出金屬擋板蓋板。 金屬擋板蓋板 4. 找到您欲安裝擴充卡插槽的位置,移除固定金屬擋板的螺絲。 5.
6. 將擴充卡對準主機板上的插槽垂直插入,使上面金手指的部份完全沒入 插槽內,並鎖上 1 顆螺絲以固定擴充卡。 7. 置回金屬擋板蓋板。 8.
2.6.2 設定擴充卡 安裝好擴充卡後,接著須藉由軟體設定來調整擴充卡的相關設定。 1. 啟動電腦,然後更改必要的 BIOS 程式設定。若需要的話,您也可以參 閱第五章 BIOS 程式設定以獲得更多資訊。 2. 為加入的擴充卡指派一組尚未被系統使用到的 IRQ。請參閱下頁表中所 列出的中斷要求使用一覽表。 3.
2.6.3 安裝 M.2 擴充卡 您可以在主機板上提供的 M.2 插槽上面安裝一張 M.2 擴充卡。 請依照以下的步驟安裝 M.2 擴充卡: 1. 找到主機板上的 M.2(NGFF1)插槽位置,如下圖所示。 2. 使用螺絲起子將鎖在 M.2 插槽上 的螺絲移除,並放置於一旁。 3. 取出 M.2 擴充卡。 4. 如右圖所示,將 M.2 擴充卡對準 主機板上的 M.2(NGFF1)插槽 裝入。 5. 鎖上步驟 1 移除的螺絲以固定 M.
2.7 連接排線 ‧ 系統內的排線在出廠前都已經預先連接妥當。您不需再另外安裝, 除非您需要更換或安裝增加的硬體,才需要重新連接/移除。 ‧ 請參考第四章以了解更多關於排線與插座連接的相關資訊。 預先連接的系統排線 1. 2. 3. 4. 5. 6. 7. 8. 9.
2.8 系統風扇 本伺服器具備四個容易抽換的前側系統風扇(80 x 80 x 38mm),讓伺 服器擁有最佳的散熱和高效能散熱解決方案。 ‧ 在移除任何元件之前,請先將系統關機。 ‧ 透過觸摸任何金屬表面以將靜電釋放。 ‧ 使用相同型號、尺寸與類型的風扇。 2.8.1 更換前側系統風扇 請依照以下的步驟,更換前側系統風扇: 1. 找到您欲更換的前側系統風扇。 2. 壓下風扇固定扣(A)以從插槽中鬆開風扇,然後將風扇往上拉(B)以 取出風扇。 3.
4.
2.9 備援式電源供應器模組 本伺服器最多提供兩組 800W 80Plus Platinum 備援式電源供應器模組, 若您當初選購的為僅搭配一組時,則您可再選購第二組,並安裝至機殼上面 提供的備援供應器模組插槽當作備援使用。 ‧ 在移除任何元件之前,請先將系統關機。 ‧ 透過觸摸任何金屬表面以將靜電釋放。 ‧ 使用相同型號與類型的備援式電源供應器模組。 安裝第二組備援式電源供應器模組 請依照以下的步驟,安裝第二組備援式電源供應器模組: 1. 朝左壓固定閂(A)。 2. 然後將金屬保護蓋板(B)從機殼 上面抽離。 3. 準備第二個備援式電源供應器模組。 請確認在安裝模組前,先卸下塑膠保護蓋。 4. 小心地將第二組備援式電源供應 器模組,置入機殼的托架內。 5.
第三章: 進階安裝 本章節要告訴您,如何使用滑軌套件將本伺服 器安裝至機架中,以及在安裝過程中必須注意的事 項。 3
3.1 免工具標準式滑軌套件 免工具的滑軌套件設計,提供您輕鬆將滑軌裝上機架並安裝伺服器至機架 中,而無須使用任何工具。這個套件並提供金屬止擋,可以讓您在安裝伺服 器時提供額外的支撐和穩定性。 免工具滑軌套件包含了以下組件: 螺絲組 固定閂 滑軌鐵件(含螺絲) 固定閂螺絲 滑軌墊圈 滑軌螺絲 免工具機架滑軌 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1.
2. 選擇所需的空間和適當的機架滑軌(左和右)放在機架的相對位置上。 在這 1U 的空間裡面要有三個方形安裝孔與在上方與底部包含二個薄型 的間隔,如下圖圈選處。 1U 3. 使用包裝內附的螺絲將滑軌鐵件安裝至滑軌上。 4. 上推彈簧鎖( ),然後將螺栓插入已選定在機架上的方形安裝孔。 5. 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如 有必要,請將機架滑軌拉長以便於安裝。 6. (可選擇)可使用附件裡的滑軌螺絲以及滑軌墊圈( 後端各鎖上兩顆套上此墊圈的螺絲以進行固定。 7. 接著請重複前面的步驟 3 至 5,安裝另一側的滑軌。 ),將滑軌前 請確認安裝的機架滑軌(左、右)有平行一致,且安穩地固定在定位。 8.
‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在 同一水平高度上。 ‧ 強烈建議至少需要兩位身強體壯的人來執行這部份的安裝作業。 ‧ 如有必要,建議使用適當的起重工具以輔助吊裝。 RS720-E8-RS24-ECP 前視圖 上圖左右側所圈選的為安裝螺絲的位置(隱藏於拉柄後方),當伺服器 裝入定位後,請使用十字螺絲將此處的螺絲鎖上以完成固定。 3-4 第三章:進階安裝
第四章: 主機板資訊 在本章中要告訴您在安裝系統元件時所必須完成 的主機板安裝程序。詳細內容有:頻率開關設定、 跳線選擇區設定以及主機板的各種裝置接頭。 4
4.1 主機板構造圖 主機板的各項元件 4-2 跳線選擇區 頁碼 1. Clear RTC RAM (CLRTC1) 4-4 2. VGA controller setting (3-pin VGA_SW1) 4-5 3. LAN controller setting (3-pin LAN_SW1-4) 4-5 4. PMBus 1.2 PSU select jumper (3-pin SMART_PSU1) 4-6 5. ME firmware force recovery setting (3-pin ME_RCVR1) 4-6 6. DDR4 thermal event setting (3-pin DIMMTRIP1) 4-7 7. RAID configuration utility selection (3-pin RAID_SEL1) 4-7 8.
主機板的各項元件 內部連接插槽 頁碼 1. Serial ATA 6.0 Gbps connectors (7-pin SATA1-6 [Light Blue], SSATA1-3 [Gray], SSATA4 [Light Gray]) 4-9 2. M.2 (NGFF) connector (NGFF1) 4-10 3. USB 2.0 connector (10-1 pin USB56) 4-10 4. USB 3.0 connector (20-1 pin USB3_34) 4-11 5. CPU, front, and rear fan connectors (4-pin CPU_FAN1-2, FRNT_FAN1-5, REAR_FAN1-2) 4-11 6. Serial General Purpose Input/Output connector (6-1 pin SGPIO1/SSGPIO1) 4-12 7. 10G LAN LED connector (5-1 pin LAN34_LED1) 4-12 8.
4.2 跳線選擇區 1.
2. VGA 控制器設定(3-pin VGA_SW1) 您可以透過本功能的設定來開啟或關閉主機板內建之 VGA 圖形顯示控制 器功能。預設值為 [1-2](開啟 VGA 功能)。 3.
4. PMBus 1.2 PSU 選擇跳線 (3-pin SMART_PSU1) 這個跳線可以提供您選擇 PSU PMBus 版本,使用 PMBus 則設為 [1-2] 短 路,其他則設為 [2-3] 短路。 5.
6. DDR3 溫度事件設定(3-pin DIMMTRIP1) 提供您啟用或關閉 DDR3 DIMM 溫度感應事件針腳的功能。 7.
8.
4.3 內部連接插座 1. Serial ATA 6.0Gb/s 連接埠(7-pin SATA1-6 [淺藍色], SSATA1-3 [灰色], SSATA4 [淺灰色]) 這些連接埠由 Intel® 612 晶片組支援,可使用 Serial ATA 訊號線連接 Serial ATA 硬碟,資料傳輸率高達 6Gb/s。 若您安裝了 Serial ATA 硬碟,您可以建立 RAID 0、RAID 1、RAID 10 或 RAID 5 磁碟陣列。關於 SATA RAID 磁碟陣列設定的詳細資訊,請參考“磁 碟陣列設定”章節的說明。 • 實際資料傳輸率取決於所安裝的 SATA 硬碟速度而定。 • 若 M.
2. M.2 (NGFF) 插槽(NGFF1) 這個插槽用來安裝 M.2(NGFF)SSD(固態硬碟)模組。 這個插槽支援 PCI-E 和 SATA 連接埠的 2242 型儲存裝置。 M.2(NGFF)固態硬碟模組為選購配件,請另行購買。 3. USB 擴充套件傳輸線插槽(10-1 pin USB56) 這些插槽可用來連接 USB 2.0 連接埠。將 USB 擴充套件連排線連接到 USB34,然後將擴充套件安裝到機殼背部的一個空置插槽位置。這些 USB 擴充套件排線插槽支援 USB 2.
4. USB 3.0 擴展套件數據線插槽(20-1 pin USB3_34) 這個插槽用來連接額外的 USB 3.0 接口模塊,並與 USB 2.0 規格兼容。 若您的機箱提供有 USB 3.0 前面板連接線,將該連線連接至本插槽,就可擁 有前面板 USB 3.0 解決方案,支持傳輸速率最高達 5Gbps,可對 USB 充電 設備進行快速充電並優化能效。 5.
6. 序列通用輸入輸出連接排針(6-1 pin SGPIO1/SSGPIO1) 此連接排針使用於 Intel Rapid Storage Technology Enterprise SGPIO 插 槽,可控制 LED 指示燈動作、裝置資訊與通用資料。SGPIO1 用於控制 SATA1~6,而 SSGPIO1 用來控制 SSATA1~4。 7.
8. 電源供應器 SMBus 連接插座 (5-pin PSUSMB1) 這組插座用來連接 SMBus (System Management Bus) 至 PSU (power supply unit),以讀取電源(PSU)訊息。裝置透過 SMBus 介面與 SMBus 主機與/或 其他使用 SMBus 插座的 SMBus 裝置進行通訊。 只有啟用 ASMB8 後此插座才有作用。 電源供應器必須符合 PMBus 規格,且需要自訂 BMC FW。若需要其他協 助,請與華碩客服人員聯絡。 9.
10. TPM 模組連接排針(20-1 pin TPM1) 這組排針支援安全性平台模組(TPM)系統,該系統可進行安全性儲存金 鑰、數位認證、密碼與資料。此外,TPM 系統也可協助增進網路安全,保 護數位辨識功能,並確保平台的整合性。 11.
12. A TX 電源插座 (24-pin EATXPWR1、8-pin EATX12V1、8-pin EATX12V2、4-pin EATX12V_NVDIMM1) 這個插座為提供給 EATX 電源使用。由電源所提供的連接插頭已經過特 別設計,只能以一個特定方向插入主機板上的電源插座。找到正確的插入方 向後,僅需穩穩地將之套進插座中即可。 • 請務必連接 24+8-pin 電源插座,否則系統將不會啟動。 • 若您想要安裝其他的硬體裝置,請務必使用較高功率的電源供應器 以提供足夠的裝置用電需求。若電源供應器無法提供裝置足夠的用 電需求,則系統將會變得不穩定或無法開機。 ‧ 本主機板支援 ATX2.
13.
14.
15. 硬碟讀寫動作指示燈連接排針 (4-pin HDLED1) 這個排針用來與 SAS 或 SATA 介面卡連接。連接到 SAS 或 SATA 介面 卡的任何裝置的讀/寫動作都會讓前面板 LED 指示燈亮燈顯示。 16.
4.4 內部指示燈 1. 電力警示燈(SBPWR1) 當主機板上內置的電力指示燈亮著時,表示目前系統是處於正常運作、 省電模式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您在 置入或移除任何的硬體裝置之前,都必須先移除電源,等待警示燈熄滅才可 進行。請參考下圖所示。 2.
3. 處理器警告指示燈(ERRCPU1、ERRCPU2) 當 CPU 發生錯誤或故障時,此 CPU 警示燈將會亮燈顯示。 4.
5. Location 指示燈(LOCLED2) 這個指示燈提供您方便地找到發生錯誤的系統所在位置。 6.
7. CATT 指示燈(CATTERRLED1) CATT 指示燈為提供當系統遭遇一個致命或災難性的錯誤,會顯示而提醒 無法繼續運作。 8.
Q-Code 列表 動作 相位 Security Phase Normal boot PEI (Pre-EFI Initialization) phase 代碼 類型 說明 01 02 03 Progress Progress Progress 06 04 10 15 19 78~00 A1 A3 A7 A8 A9 AA AB AC AD AE AF 2F B0 B1 AF B4 B2 B3 B5 B6 B7 B8 B9 BA BB BC BF 5A 31 32 34 36 4F Progress Progress Progress Progress Progress Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress Progress MRC Progress MRC Progress MRC Progress MRC Progress M
動作 相位 代碼 60 61 62 63 68 DXE (Driver 69 Execution Environment) 6A phase 70 71 72 78 79 90 91 92 93 94 95 96 97 98 Normal boot 99 9A 9B 9C BDS (Boot Device 9D Selection) phase b2 b3 b4 b6 b7 A0 A1 A2 A3 A8 A9 AB AD AE Operating system AA phase AC 4-24 第四章:主機板資訊 類型 說明 Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progr
第五章: BIOS 程式設定 BIOS 程式調校的優劣與否,和整個系統的運作效 能有極大的關係。針對自己的配備來作最佳化 BIOS 設定,可讓您的系統性統再提升。本章節將逐一說 明 BIOS 程式中的每一項組態設定。 5
5.1 管理、更新您的 BIOS 程式 下列軟體讓您可以管理與更新主機板上的 BIOS 設定。 1. ASUS CrashFree BIOS 3 當 BIOS 程式毀損時,使用可開機的 USB 隨身碟來更新 BIOS 程式。 2. ASUS EZFlash 使用 USB 隨身碟更新 BIOS。 3. BUPDATER 使用可開機的 USB 隨身碟在 DOS 環境下更新 BIOS 程式。 上述軟體請參考相關章節的詳細使用說明。 建議您先將主機板原始的 BIOS 程式備份到可開機的 USB 隨身碟中, 以備您往後需要再度安裝原始的 BIOS 程式。使用華碩線上更新(ASUS Update)程式來拷貝主機板原始的 BIOS 程式。 5.1.
5.1.2 使用華碩 EZ Flash 更新程式 華碩 EZ Flash 程式讓您能輕鬆的更新 BIOS 程式,可以不必再透過開機 片的冗長程序或是到 DOS 模式下執行。 請至華碩網站 http://tw.asus.com 下載最新的 BIOS 程式檔案。 請依照下列步驟,使用 EZ Flash 來更新 BIOS: 1. 將已存好最新版 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式。來到 Tools 選單,選擇 ASUS EZ Flash Utility 後 並按下 鍵將其開啟。 ASUS Tek.
• 本功能僅支援採用 FAT 32/16 格式的單一磁區 USB 隨身碟。 • 當更新 BIOS 時,請勿關閉或重置系統以避免系統開機失敗。 為確保系統的相容性與穩定性,請按下 鍵並選擇 Yes 以載入預設 的 BIOS 設定。 5.1.3 BUPDATER 工具程式 以下的 BIOS 畫面僅供參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程式可以提供您在 DOS 環境下,使用儲存有更新的 BIOS 檔案的 USB 隨身碟來更新 BIOS 檔案。 更新 BIOS 檔案 請依照以下的步驟,使用BUPDATER 工具程式來更新 BIOS 檔案: 1. 請先造訪華碩網站(tw.asus.com)下載最新主機板的 BIOS 檔案。並將 檔案儲存至可開機的 USB 隨身碟內。 2. 然後將華碩支援網站(support.asus.com)上的 BUPDATER 工具程式 (BUPDATER.exe),下載並儲存至同一個可開機的 USB 隨身碟內。 3. 將系統開機至 DOS 環境下,然後使用鍵盤輸入指令: BUPDATER /i[filename].
4. 程式會進行檢查檔案,然後開始更新 BIOS 檔案。 ASUS Tek. EzFlash Utility Current Platform Platform : Z10PE-D16 Version : 0301 Build date: 05/13/2014 Start Programming Flash. New Platform Platform : Z10PE-D16 Version : 0301 Build date: 05/13/2014 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程式檔案時關閉或重新啟動系統,此舉將會導致系統 損毀! 5. 當 BIOS 更新完畢後該程式會返回 DOS 指令。請從硬碟重新啟動系統。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS720-E8-RS24-ECP 使用手冊 5-5
5.2 BIOS 程式設定 主機板擁有一片可編輯的韌體晶片,您可以依照 5.
5.2.1 BIOS 程式選單介紹 選單項目 功能表列 設定值 一般說明 操作功能鍵 5.2.
5.2.3 選單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功 能,則會顯示 Main 選單的項目。 點選選單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、 Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子選單 在選單畫面中,若功能選項的前面有一個小三角形標記,代表此為子選 單,您可以利用方向鍵來選擇,並且按下 鍵來進入子選單。 5.2.5 操作功能鍵說明 在選單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改 變各項功能。 5.2.6 一般說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依 選項的不同而自動變更。 5.2.7 設定值 這些存在於選單中的設定值是提供給使用者選擇與設定之用。這些項目 中,有的功能選項僅為告知使用者目前運作狀態,並無法更改,那麼此類項 目就會以淡灰色顯示。而可更改的項目,當您使用方向鍵移動項目時,被選 擇的項目以反白顯示,代表這是可更改的項目。 5.2.
5.3 主選單(Main) 當您進入 BIOS 設定程式時,首先出現的第一個畫面即為主選單,內容如 下圖。 5.3.1 System Date [Day xx/xx/xxxx] 設定您的系統日期。 5.3.
5.
5.4.1 ACPI 設定 Enable ACPI Auto Configuration [Disabled] 本項為啟用或關閉 BIOS ACPI 自動設定。設定值有:[Disabled] [Enabled]。 Enable Hibernation [Enabled] 本項啟用或關閉 Hibernation 功能(OS/ 休眠狀態)設定值有:[Disabled] [Enabled]。 本項目可能對部分作業系統無任何作用。 5.4.
5.4.
5.4.
5.4.
Parity [None] 一個 parity(同位)位元能發送資料位元來檢測一些傳輸錯誤,[Mark] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為偶數。 [Odd] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為奇數。 [Mark] 同位位元總是 1。 [Space] 同位位元總是 0。 Stop Bits [1] Stop bits 為序列資料封包的終點(開始位元表示起始)。標準設定是 1 Stop bit。使用較慢的裝置通訊可能會需要超過 1 stop bit。設定值有:[1] [2]。 Flow Control [Hardware RTS/CTS] Flow control(流量控制)能預防在緩衝區溢滿時的資料流失。當傳送資料 時,若接收的緩衝區已經滿了,此時會送出“stop”(停止)訊號來停止傳送資 料流(data flow)。當緩衝區空出時,會再送出“start”(開始)訊號以重新開 始傳送資料流。硬體流量控制使用兩條金屬線來傳送 start/stop(開始/停止)訊 號。設定值有:[
Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] 啟用或關閉控制台轉向功能。設定值有: [Disabled] [Enabled]。 當 Console Redirection 設定為 [Enabled] 時,以下的項目才會顯示。 Console Redirection Settings Out-of-Band Mgmt Port [COM1] 經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[COM1] [COM2]。 Terminal Type [VT-UTF8] 此為微軟 Windows Emergency Management Services (EMS) 提供 Windows Server 作業系統可以透過序列埠來採用遠端遙控管理。設定值有:[VT100] [VT100+] [VT-UTF8] [ANSI]。 Bits per second [115200] 此為微軟 Windows Emergen
5.4.
5.4.
5.4.
5.4.
5.4.
5.4.
USB hardware delays and time-outs USB transfer time-out [20 sec] 選擇 USB 移轉暫停值,以提供控制、bulk 與中斷傳輸。設定值有:[1 sec] [5 sec] [10 sec] [20 sec]。 Device reset time-out [20 sec] USB 大量儲存裝置起始單元指令暫停時間。設定值有:[10 sec] [20 sec] [30 sec] [40 sec]。 Device power-up delay [Auto] 在做適當的自我回報給 Host Controller(主機控制器)之前,提供您在設 定採用最大時間值。設定值有:[Auto] [Manual]。 5.4.
5.
5.5.1 處理器設定(CPU Configuration) Per Socket Configuration 提供您設定啟用的核心數。0 表示所有核心,總共有 14 個核心可用。 Hyper Threading [Enabled] 本項目提供您啟用或關閉 Intel Hyper-Threading(高速執行緒)技術, 當關閉(Disabled)時,僅會啟動單線程核心。設定值有:[Disabled] [Enabled]。 Execute Disable Bit [Enabled] 當搭配結合支援的 OS(Windows Server 2003 SP1、Windows XP SP2、 SuSE Linux 9.
Enable SMX [Disabled] 本項目為啟用 Safer Mode Extensions(SMX,安全模式延展)功能。設定 值有:[Disabled] [Enabled]。 Hardware Prefetcher [Enabled] 本項目提供您開啟或關閉中間層快取(mid level cache,L2)streamer prefetcher 功能。設定值有:[Disabled] [Enabled]。 Adjacent Cache Line Prefetch [Enabled] 本項目提供您啟用或關閉 Adjacent Cache Line Prefetch 功能。設定值有: [Disabled] [Enabled]。 DCU Streamer Prefetcher [Enabled] 本項目為啟用或關閉 L1 資料 prefetcher。設定值有:[Disabled] [Enabled]。 DCU IP Prefetcher [Enabled] 本項目提供您啟用或關閉下一個基於隨著在載入記錄之上的 L1 線。設定 值有:[Disabled] [Enabled]。 DCU Mode [3
5.5.
5.5.4 QPI 設置 QPI General Configuration QPI Status 本項目顯示 QPI 狀態的相關資訊。 Link Speed Mode [Fast] 本項目為提供設定 QPI 連線速度為任一快速模式(fast mode)或慢速模 式(slow mode)。設定值有:[Slow] [Fast]。 Link Frequency Select [Auto] 本項目用來選擇 QPI 連線頻率。設定值有:[Auto] [6.4 GT/s] [8.0 GT/s] [9.
5.5.
Memory Power Savings Advanced Options CK in SR [Auto] 設定值有:[Auto] [Driven] [Tri-State] [Pulled Low] Pulled High]。 MDLL Off [Auto] 若設為開啟,您可以在 SR 時關閉 MDLL。設定值有:[Auto] [Disabled] [Enabled] MEMHOT Throttling Mode [Input-only] 若設為開啟,您可以在 SR 時關閉 MDLL。設定值有:[Disabled] [Input-only] [Output-only]。 Mem Electrical Throttling [Disabled] 本項為設定 Memory Electical throttling(記憶體電動節流)功能。設定值有: [Disabled] [Enabled] [Auto]。 Memory Map Channel Interleaving [Auto] 提供選擇不同的 channel interleaving 設定。設定值有:[Auto] [1-way Interleave] [
5.5.
5.5.
PCH SATA Configuration SATA Controller [Enabled] 本項目用來啟用或關閉 SATA 控制器。設定值有:[Disabled] [Enabled]。 Configure SATA as [AHCI] 本項目用來辨識連接 Solid State Drive(SSD)硬碟或硬碟機裝置的 SATA 連接埠。設定值有:[IDE] [AHCI] [RAID]。 SATA Mode options SATA LED locate [Enabled] 若設為啟用,LED/SGPIO 硬體已連接。設定值有:[Disabled] [Enabled]。 Support Aggressive Link Power Management [Enabled] 啟用或關閉 Suport Aggressive Link Power (SALP) 管理功能。設定值有: [Disabled] [Enabled]。 SATA Port 1~6 Port 1/ Port 2/ Port 3/ Port 4/ Port 5/ Port 6 [Enabled] 本項目用來啟用或關閉 SATA 連接埠。
Platform Thermal Configuration PCH Thermal Device [Auto] 本項目用來啟用或關閉 PCH 散熱裝置 (D31:F6)。設定值有:[Auto] [Disabled] [Enabled]。 Alert Enable Lock [Disabled] 本項目用來鎖定所有警告開啟設定。設定值有:[Disabled] [Enabled]。 5.5.8 Miscellaneous Configuration(平台其他設定) Active Video [Offboard Device] 本項目用來選擇視頻輸出類型。設定值有:[Onboard Device] [Offboard Device]。 5.5.9 Server ME 設定 顯示在您系統上的 Server ME 技術的參數。 5.5.
5.
System Event Log 提供您變更 SEL(系統事件記錄)設定。 SEL Components [Disabled] 提供您啟用或關閉開機時系統 Event Logging 的所有功能。設定值有: [Disabled] [Enabled]。 • 當 SEL Components 項目設為 [Enabled] 時,以下項目才會出現。 • 此部份的所有設定的變更將在系統重新開機後生效。 Erase SEL [No] 提供您選擇刪除 SEL 的選項。設定值有:[No] [Yes, On next reset] [Yes, On every reset]。 When SEL is Full [Do Nothing] 提供您選擇當事件記錄存滿時的反應選項。設定值有:[Do Nothing] [Erase Immediately]。 Log EFI Status Codes [Error code] 關閉 EFI 狀態碼記錄,或僅記錄錯誤碼,或僅記錄進程碼,也可以同時記 錄。設定值有:[Disabled] [Both] [Error code] [Progress code]。 Bmc network
View System Event Log 本項目可檢視系統事件記錄。 IPv6 BMC Network Configuration 本項目用來設定 IPv6 BMC 網路參數。 IPv6 Display Full Field [Enable] 顯示完整或簡要的 IPv6 欄位。設定值有:[Disable] [Enable]。 IPv6 Display Full Formula [Enable] 顯示完整或簡要的 IPv6 Formula。設定值有:[Disable] [Enable]。 IPv6 Display Letter Case [Upper Case] 顯示大寫或小寫字母。設定值有:[Lower Case] [Upper Case]。 IPv6 BMC Lan Option [Enable] 提供啟用或關閉 IPv6 BMC 網路頻道功能。關閉這個項目則將無法在 BIOS 程 式中修改任何 BMC 網路。設定值有:[Disable] [Enable]。 IPv6 BMC LAN IP Address source [Previous State] 選擇設定 LAN 頻道參數為採靜態或動態(經由
IPv6 BMC LAN IP Prefix Length 提供輸入 IPv6 BMC 網路 IP 字首長度。 IPv6 BMC LAN Default Gateway 提供輸入 IPv6 BMC 網路預設閘道。 IPv6 BMC LAN DNS Settings 提供輸入 IPv6 BMC 網路 DNS 設定值。 IPv6 BMC LAN Link IP Address 提供輸入 IPv6 BMC 網路連線 IP 位址。 IPv6 BMC LAN Link IP Prefix Length 提供輸入 IPv6 BMC 網路連線 IP 字首長度。 IPv6 BMC Lan Option [Enable] 本項目提供啟用 IPv6 BMC 網路通道功能。關閉本項目則將無法在 BIOS 裡修改任何 BMC 網路設定。 以下項目僅當 IP BMC Lan Option 設為 [Enabled] 時才會顯示。 IPv6 BMC LAN IP Address Source [Previous State] 選擇設定的網路通道的參數為靜態或動態(透過 BIOS 或 BMC)。未指定 選項將不會修改在 BIOS 裡的任
5.7 事件記錄選單(Event Logs menu) 事件記錄選單(Event Logs)選項提供您變更事件記錄設定以及查看系統 事件記錄。 5.7.
Smbios Event Log Standard Settings Log System Boot Event [Disabled] 選擇啟用或關閉系統開機事件記錄。設定值有:[Enabled] [Disabled]。 MECI [1] 提供您調整 MECI(Multiple Event Count Increment),此為設定 same error 重複出現的次數。使用 <+> 與 <-> 鍵調整數值,數值的範圍為 1 至 255。 METW [60] 提供您調整 METW (Multiple Event Time Window) 數值,此為設定 same error 重複出現的最小時間差距。使用 <+> 與 <-> 鍵輸入調整數值,數值的 範圍為 0 至 99。 Custom Option Log OEM Codes [Enabled] 本項為啟用或關閉 EFI 記錄狀態編碼為 OEM 編碼。設定值有:[Disabled] [Enabled]。 Convert OEM Codes [Disabled] 提供您啟用或關閉轉換 EFI 狀態編碼為標準 Smbios 類型(並非所有可能 編譯)。設定
5.8 監控選單(Monitor menu) 本選單顯示系統監控或電源狀態,並且提供您變更風扇設定。 往下捲動可以看到更多的項目。 CPU 1/2 Temperature [xxx℃/xxx℉] 本系統具備溫度感測器,可自動偵測並顯示目前主機板零組件與處理器 的溫度。 CPU FAN1/2 Speed; FRNT FAN1–5 Speed; REAR FAN1/2 Speed [xxxx RPM] or [N/A] 為了避免系統因為過熱而造成損壞,本系統具備有處理器風扇、前置風 扇與後置風扇的轉速 RPM(Rotations Per Minute)顯示。若該欄位顯示為 [N/A],則表示風扇並未連接至主機板上的該插座。 +VCCIO, VCORE1/2 Voltage, +VDDQ_AB_CPU1 Voltage, +VDDQ_CD_CPU1 Voltage, +VDDQ_EF_CPU2 Voltage, +VDDQ_ GH_CPU2 Voltage, +5VSB Voltage, +5V Voltage, +12V Voltage, +3.3V Voltage, VBAT Voltage, +3.
FRNT FAN2&3/4&5; REAR FAN1&2 mode [Generic Mode] 提供您設定華碩智慧型風扇(ASUS Smart Fan)功能,可以有智慧地調 整風扇速度以提升系統整體運作。設定值有:[Generic Mode] [High Speed Mode] [Full Speed Mode] [Manual Mode]。 5.9 安全性選單(Security menu) 本選單可以讓您變更系統安全設定,並且提供您啟用或關閉安全開機 (Secure Boot)狀態與讓使用者設定系統模式(System Mode)狀態。 Administrator Password(設定系統管理員密碼) 當您設定系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設定程 式中的某些資訊無法檢視或變更設定。 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3.
欲刪除系統管理員密碼時,請依照變更系統管理員密碼之步驟,但請在 輸入/確認密碼視窗出現時,按下 鍵。當您刪除系統管理員密碼後, Administrator Password 項目將顯示為 Not Installed。 User Password(設定使用者密碼) 當您設定使用者密碼後,你必需登入您的帳戶才能使用 BIOS 設定程式。 使用者密碼的預設值為 Not Installed,當您設定密碼後將顯示 Installed。 請依照以下步驟設定使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更使用者密碼(User Password): 1. 2. 3. 4.
Key Management 本項目僅當 Secure Boot Mode 設定為 [Custom] 時才會顯示,提供您修改 Secure Boot(安全開機)變量與設定 Key Management(密鑰管理)頁面。 Default Key Provision [Disabled] 設定值有:[Disabled] [Enabled]。 Enroll All Factory Default Keys 若您想要安裝系統預設安全變量,本項目將會進行詢問。若您想要載入預設 的安全變量,請選擇 Yes;否則請選擇 No。 Save All Secure Boot Variables 若您想要儲存所有安全變量,本項目將會進行詢問。選擇 Yes 進行儲存;或 選擇 No 取消。 Platform Key (PK)/ Key Exchange Key (KEK)/ Authorized Signatures (DB)/ Authorized TimeStamps (DBT)/ Forbidden Signatures (DBX) 設定值有:[Delete] [Set New] [Append]。 5-44 第五章:B
5.
• 若要在開機過程中選擇開機裝置,請於開機看到 ASUS 圖示時按下 鍵 • 您可以在 POST(開機自我測試)時,按下 鍵進入 Windows 作業系統的安全模式(Safe Mode)。 設定網路裝置的開機順序。 Boot Option #1/#2 [SATA P2: ASUS ...] 設定值有:[SATA P2: ASUS ...] [SATA P3: WDC WD80 ...] [AMI Virtual Floppy ...] [IBA GE Slot 0700 v ...]。 CD/DVD ROM Drive BBS Priorities Hard Drive BBS Priorities / Floppy Drive BBS Priorities / Network Device BBS Priorities 只有當您連接了 SATA 光碟機或硬碟至 SATA 連接埠時,這兩個項目才會出 現,用來設定 SATA 裝置的開機順序。 5.
5.
Discard Changes 取消儲存目前所做的任何變更選項。 Restore Defaults 本項目提供您還原或載入所有選項的預設值。在選擇本項目後,將會出 現一個確認對話視窗,請選擇 Yes 以載入有效的預設值。 Save as User Defaults 根據使用者預設(User Defaults)儲存變更。 Restore User Defaults 還原使用者預設(User Defaults)至所有設定選項。 Boot Override 這些項目會顯示可用的裝置。顯示在畫面中的裝置則是根據安裝在系統 裡的裝置而定,點選任一個項目可以設定該項目裡所列裝置的開機順序。 Launch EFI Shell from filesystem device 本項目可以讓您由含有資料系統的裝置中啟動 EFI Shell(shellx64.
第六章: 磁碟陣列設定 在本章節中,我們將介紹關於伺服器的磁碟陣列 的設定與說明。 6
6.1 RAID 功能設定 本系統提供以下的 SATA RAID 解決方案: ‧ LSI MegaRAID Software RAID 工具程式,支援 RAID 0、RAID 1 與 RAID 10 設定(在 Linux 與 Windows 系統環境下使用)。 ‧ Intel® Rapid Storage Technology enterprise SATA Option ROM 工具 程式,可以讓您建立 RAID 0、RAID 1、RAID 10 和 RAID 5 磁碟陣 列設定(適用於 Windows 作業系統)。 6.1.
‧ 若想要從已建立 RAID 的硬碟進行系統開機,請先將驅動及公用程 式光碟內的 RAID 驅動檔案複製至磁碟片中,如此才能於安裝作業 系統時一併選擇驅動磁碟陣列功能。 ‧ 請參考第四章的說明以了解如何選擇 RAID 設定程式。 6.1.2 安裝 Serial ATA(SATA)硬碟機 本主機板支援 Serial ATA 硬碟機。為了最佳的效能表現,當您要建立陣 列模式設定時,請盡可能採用具備相同型號與容量的硬碟機。 請依照以下安裝方式(或參考 2.4 安裝硬碟機 的內容)來安裝 SATA 硬 碟至硬碟槽裡。 1. 將硬碟安裝至硬碟槽中。 2. 安裝硬碟連接排線,將欲建構磁碟陣列的硬碟連接至主機板。 3. 將 SATA 電源線連接到每一部硬碟機。 6.1.3 在 BIOS 程式中設定 RAID 在您開始建立陣列之前,您必須先在 BIOS 程式設定中設定對應的 RAID 選項。請依照下列步驟進行操作︰ 1. 在開機後系統仍在進行開機自我測試(Power-On Self Test,POST)時, 按下 按鍵進入 BIOS 設定程式。 2.
6.2 LSI Software RAID 設定程式 LSI MegaRAID Software RAID 設定程式可以提供您建立 RAID 0、RAID 1 或 RAID 10 設定,此為經由主機板上內建的南橋晶片與連接的 SATA 硬碟 機來建立。 請依照以下的步驟來開啟 LSI MegaRAID software RAID 設定程式: 1. 在安裝好所有的 SATA 硬碟機後,開啟系統。 2. 當在自我測試進行時,LSI MegaRAID software RAID 設定程式會自動 偵測所安裝的 SATA 硬碟機與顯示現存的 RAID 設定。請按下 + 鍵來進入此程式。 LSI MegaRAID Software RAID BIOS Version A.
選單項目 Configure Initialize 說明 您可以透過 Easy Configuration 或 New Configuration 功能來建立 RAID 0、RAID 1 或 RAID 10 設定。這個選單也可以讓您檢視、新增或刪除 RAID 的設定,或是選擇開機的硬碟裝置 允許您初始已建立 RAID 設定的虛擬磁碟機 Objects 允許您初始虛擬磁碟機或變更虛擬磁碟的參數 Rebuild 允許您重建失效的磁碟機 Check Consistency 提供您檢查已建立 RAID 設定的虛擬磁碟機的資料一致性 6.2.
2. 在 ARRAY SELECTION MENU 畫面中,顯示目前連接且可用的 SATA 硬碟機有多少部。選擇您要進行設定 RAID 的硬碟機,然後按下 <空白 > 鍵。當選擇時,硬碟指示會從 READY 變更成 ONLIN A[X] - [Y],而 X 所代表的是任何數字,且 Y 表示硬碟裝置的數字代號。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Easy Configuration - ARRAY SELECTION MENU Management Menu Configure Initialize Objects Rebuild Check Consistency Port # 2 DISK PORT # 0 ONLIN A00-00 1 ONLIN A00-01 2 READY 3 READY 74.74GB HDS728080PLA380 05.
5. 再次按 鍵,這時會在 Virtual Drive 選單中看到虛擬磁碟的資訊, 並且可以讓您進行變更虛擬磁碟機的參數。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R LD Virtual Drive(s) Configured Easy -#Stripes ARRAY SELECTION MENU RAID Configuration Size StripSz Management Menu Configure 0 Initialize Objects Rebuild Check Consistency 1 148.
8. 從 Virtual Drive 子選單裡選擇 Units,然後按下 鍵。 9. 從選單裡選擇 units 的 virtual drive 大小,然後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R LD Virtual Drive(s) Configured Easy -#Stripes ARRAY SELECTION MENU RAID Configuration Size StripSz Management Menu Configure 0 Initialize Objects Rebuild Check Consistency 1 148.
12. 當完成所選擇的虛擬磁碟裝置的設定時,請選擇畫面中的 Accept,然後 按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R LD Virtual Drive(s) Configured Easy -#Stripes ARRAY SELECTION MENU RAID Configuration Size StripSz Management Menu Configure 0 Initialize Objects Rebuild Check Consistency 1 148.
使用 New Configuration 設定 當一個 RAID 設定已經存在,使用 New Configuration 指令來清除存在 的 RAID 設定資料。若您不要刪除已存在的 RAID 設定,使用 View/Add Configuration 選項來檢視或建立其他的 RAID 設定。 請依照以下步驟,使用 New Configuration(新增設定)模式來建立一個 RAID 設定: 1. 進入主選單畫面後,選擇 Configure > New Configuration 項目,然後按 鍵繼續。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
6.2.2 新增或檢視一個 RAID 設定 您可以使用 View/Add Configuration 功能來新增一個新的 RAID 或者是檢 視一個現存的 RAID 設定。 新增一個 RAID 設定 請依照以下步驟新增一個 RAID 設定: 1. 進入主選單畫面後,選擇 Configure > View/Add Configuration 項目,然 後按 鍵繼續。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
6.2.3 將虛擬磁碟初始化 當您完成建立 RAID 設定時,您必須將虛擬磁碟做初始化。您可以透過主 選單畫面中的 Initialize 或 Objects 選項,進行虛擬磁碟初始化的動作。 使用 Initialize 指令設定 請依照以下步驟,使用 Initialize(初始化)功能: 1. 進入主選單畫面後,選擇 Initialize 選項,然後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency Initialize VD(s) Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option 2.
3. 當出現提示時,按下 <空白> 鍵後,從 Initialize? 的對話框中選擇 Yes,然後按下 鍵。您也可以透過按下 鍵來初始化硬碟 裝置,而不需要再做任何確認動作。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency LD 0 Virtual Drive(s) Configured Easy -#Stripes ARRAY SELECTION MENU RAID Configuration Size StripSz 1 148.
使用 Objects 指令設定 請依照以下步驟使用 Objects 功能: 1. 進入主選單畫面,選擇 Objects > Virtual Drive 選項後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Objects Management Menu Adapter Configure Virtual Drive Initialize Physical Drive Objects Rebuild Check Consistency Change VD Parameters Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 2.
3. 從彈出的子選單中選擇 Initialize 選項,然後按下 鍵開始進行硬 碟初始化。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Objects Virtual Drive(1) Virtual Drive 0 Management Menu Adapter Configure Virtual Drive Initialize Physical Drive Objects Virtual Drive(0) Rebuild Initialize Check Consistency Check Consistency View/Update Parameters Initialize VD Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 4.
6.2.4 重新建立損壞的硬碟 您可以採用手動的方式重新建立損壞的硬碟裝置,透過使用主選單畫面 中的 Rebuild 指令來達成。 請依照以下步驟重新建立損壞的硬碟: 1. 進入主選單畫面後,選擇 Rebuild 選項,然後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency Rebuild VD(s) Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option 2.
3. 當選擇欲重新建立的硬碟後並按下 鍵,所選擇的硬碟裝置則會顯 示 RBLD 的指示。當出現對話框時,請按下 來重新建立硬碟裝置。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R REBUILD - PHYSICAL DRIVES SELECTION MENU Management Menu Configure PORT # Initialize 0 ONLIN A00-00 Objects 1 FAIL A00-01 Rebuild Rebuilding of Drive Will Take A Few Minutes.
6.2.5 檢查硬碟資料的一致性 您可以檢查與核對所選擇硬碟裝置中資料一致性的正確性。這個工具程 式自動偵測或發現並修正資料冗位的任何差異,選擇 Objects > Adapter 選 項來進行。 Check Consistency(一致性檢查)指令可用在包含 RAID 1 與 RAID 10 設定下的虛擬磁碟機。 使用 Check Consistency 指令設定 請依照以下步驟,使用 Check Consistency 指令檢查資料的一致性: 1. 進入主選單畫面選擇 Check Consistency 選項後,按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
3. 當出現提示時,按下 <空白> 鍵並從 Consistency Check? 的對話框中選 擇 Yes,然後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
使用 Objects 指令 請依照以下的步驟,使用 Objects 指令檢查資料的一致性: 1. 進入 主選單畫面(Management Menu)後,選擇 Objects 中的 Virtual Drive 選項。 2. 使用方向鍵選擇您所要檢查的虛擬磁碟機後,按下 鍵。 3. 從子選單中選擇 Check Consistency 後,按下 鍵。 4. 當出現對話框時,使用方向鍵選擇 Yes 後,開始進行檢查硬碟。 5.
6.2.6 刪除一個 RAID 設定 您可以依照以下步驟刪除一個 RAID 設定: 1. 進入主選單畫面選擇 Configure > Clear Configuration 後按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.09231523R Configuration Menu Easy Configuration Management MenuNew Configuration Configure View/Add Configuration Initialize Clear Configuration Objects Select Boot Drive Rebuild Check Consistency Clear Existing Configuration Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 2.
6.2.7 從 RAID 設定中選擇開機磁碟 在您要設定選擇開機磁碟前,您必須已經建立好一個新的 RAID 設定。請 參考 6.2.1 使用 New Configuration 設定 的說明。 您可以依照以下的步驟,來刪除一個 RAID 設定: 1. 進入主選單畫面選擇 Configure > Select Boot Drive 後,按下 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
6.2.8 開啟 WriteCache 在您完成建立一個 RAID 設定後,您可以手動啟用 RAID 控制功能的 WriteCache 選項,來新增資料傳輸時的效能。 當您開啟 WriteCache 功能時,在硬碟傳輸或交換資料時若發生電源中 斷,可能會導致檔案遺失。 建議在 RAID 1 與 RAID 10 設定上使用 WriteCache 功能。 您可以依照以下步驟啟用 WriteCache 功能: 1. 當進入主選單畫面後,選擇 Objects > Adapter 後,按下 鍵顯示 介面的屬性。 2. 選擇 Disk WC 後,按下 鍵開啟選項。 LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010 BIOS Version A.10.
6.3 I ntel ® Rapid Storage Technology enterprise SATA/SSATA Option ROM 工 具程式 Intel® Rapid Storage Technology enterprise SATA Option ROM 工具程式 經由南橋晶片的支援,可讓您使用安裝在系統中的 Serial ATA 硬碟機建立 RAID 0、RAID 1、RAID 10(1+0)與 RAID 5 設定。 在您進行前,請確認您已裝妥 Serial ATA 硬碟機,並且調整好正確的主 機板跳線設定,然後在 BIOS 程式中設定正確的 SATA 模式。您可以參 考 6.1.2 ~ 6.1.4 節的內容,以了解更多相關的說明。 請依照下列步驟,進入 Intel® Rapid Storage Technology enterprise SATA Option ROM 程式: 1. 啟動您的電腦。 2.
6.3.1 建立 RAID 設定 請依照下列步驟建立一個 RAID 設定: 1. 從主選單畫面中選擇 1. Create RAID Volume,然後按下 <Enter> 鍵, 會出現如下圖所示的畫面。 2. 為您的 RAID 鍵入一個名稱,然後按下 鍵。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: RAID0(Strips) Disks: Select Disks Strip Size: 128KB Capacity: 0.
6. 使用向上/向下方向鍵來選擇磁碟陣列的 stripe 大小(僅支援 RAID 0、 10 與 5 設定時使用),然後按下 鍵。其數值可由 4KB 遞增至 128KB。本項目建議依照以下的使用需求,以進行正確的設定。 ·RAID 0:128KB ·RAID 10:64KB ·RAID 5:64KB 若您所使用的是伺服器系統,建議選擇較低的陣列區塊大小;若是用於 處理音樂、影像剪輯的多媒體電腦系統,則建議選擇較高的陣列區塊大 小。 7. 選擇 Capacity 項目,輸入您所要的陣列容量,接著按下 鍵。本 項目預設值是採用最高可容許的容量。 8. 在 Create Volume 的提示對話框中,再按下 鍵來建立磁碟陣列, 接著便會出現如下圖的警告訊息畫面。 9. 按下 來建立陣列並回到主選單,或是按下 鍵,回到 CREATE ARRAY(建立陣列)選單。 WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
6.3.2 刪除 RAID 磁區 在操作此功能時請務必非常小心,所有在硬碟中的資料將被刪除。 請依照下列步驟刪除 RAID 磁區︰ 1. 選擇 2. Delete RAID Volume 選項後,按下 鍵進入設定畫面。 2. 使用向上、向下方向鍵選擇您所要刪除的陣列後,按下 鍵刪除 RAID 磁區。在按下確認後,會出現如下圖所示的確認畫面。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Volume0 Level RAID0(Stripe) Drives 2 Capacity 298.
6.3.3 重新設定硬碟為非陣列硬碟 請注意!當您將 RAID 陣列硬碟設定為無 RAID 陣列狀態時,所有磁碟 陣列中的資料與陣列本身的結構資料都將被移除。 請依照下列步驟重新設定 RAID 硬碟。 1. 選擇選項 3. Reset Disks to Non-RAID 後,按下 鍵以顯示以下的 畫面。 2. 使用向上/向下方向鍵選擇您所想要重新設定的所有 RAID 硬碟組,並按 下 <空白> 鍵確認。再按下 鍵重新設定 RAID 硬碟組。接著會顯 示一個確認訊息。 [ RESET RAID DATA ] Resetting RAID disk will remove its RAID structures and revert it to a non-RAID disk. WARNING: Resetting a disk causes all data on the disk to be lost.
6.3.4 退出 Intel Rapid Storage Technology enterprise 程 式 請依照下列步驟退出公用程式︰ 1. 在公用程式主選單中,請選擇 4. Exit 然後按下 鍵,會出現如下 所示的畫面。 [ CONFIRM EXIT ] Are you sure you want to exit? (Y/N): 2. 請按下 鍵以退出程式,或按下 鍵回到功能設定主選單。 6.3.5 重建 RAID 設定 此選項支援 RAID1、RAID 5 和 RAID 10 設定。 使用非 RAID(Non-RAID)硬碟重建 RAID 設定 若有任何在 RAID 1 陣列設定中的 SATA 硬碟發生損壞時,系統會在開機 自我偵測(POST)進行時,顯示該 RAID 狀態為“Degraded”,您可以使 用其他已經安裝的非 RAID 硬碟來重建該 RAID 設定。 請依照以下步驟,使用非 RAID(Non-RAID)硬碟重建 RAID 設定: 1.
3. 選定之後,程式會立即開始進行重建,並且顯示該 RAID 的狀態為 “Rebuild”。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. 1. Create RAID Volume 2. Delete RAID Volume RAID Volumes: ID Name 1 Volume0 [ MAIN MENU ] 3. Reset Disks to Non-RAID 4. Exit [ DISK/VOLUME INFORMATION] Level1 RAID1(Mirror) Physical Devices: Port Drive Model 1 ST3160812AS 2 ST3160812AS Strip N/A Serial # 9LS0F4HL 3LS0JYL8 Size 149.0GB Size 149.0GB 149.
6.3.6 在 BIOS 程式中設定開機陣列 當您使用 Intel® Rapid Storage Technology enterprise SCU/SATA Option ROM 建立多重 RAID(multi-RAID)時,您可以將您所設定的 RAID 陣列於 BIOS 程式中設定開機優先順序。 請依照以下的步驟,於 BIOS 程式中設定開機陣列: 請從硬碟中至少設定一個開機陣列。 1. 請在開機自我偵測(POST) 時,按下 鍵進入 BIOS 程式設定畫 面。 2. 進入 Boot 選單,然後選擇 Boot Device Priority 項目。 3. 使用向上/向下方向鍵,選擇開機順序後按下 鍵,請參考 5.10 開機選單(Boot Menu)的說明。 4. 從 Exit 選單中,選擇 Exit & Save Changes,然後按下 鍵。 5.
6.4 I ntel ® Rapid Storage Technology enterprise 工具程式(Windows) The Intel® Rapid Storage Technology enterprise 工具程式提供您使用安 裝在系統中的 Serial ATA / SAS 硬碟裝置建立 RAID 0、RAID 1、RAID 10 (1+0)與 RAID 5 設定。 在 Windows 作業系統環境中,進入 Intel ® Rapid Storage Technology enterprise 程式: 1. 開機並進入作業系統桌面。 2.
6.4.1 建立 RAID 設定 請依照以下步驟建立 RAID 設定: 1. 在前面的主選單畫面中,點選 Create Volume 並選擇 volume 類型。 2. 點選 Next 繼續。 3. 輸入欲建立 RAID 設定的名稱,然後選擇陣列要用的磁碟。 4. 選擇 Volume Size 欄位,您可以拖曳畫面中的橫桿以決定容量大小。 5.
6. 確認建立,請點選 Create Volume 繼續。 建立的過程會因數量與容量不同而需要等候一段時間,在此期間,您可 以繼續使用其他的應用程式。 7.
6.4.2 變更 Volume 類型 當您完成建立 RAID 設定時,您可以在 Volume Properties 欄位中檢視或 變更裡頭的各個項目。 您可以依據以下步驟變更 Volume Properties 的類型: 1. 在 Volumes 欄位中點選您想要變更的 SAS 或 SATA 陣列。 2 然後在 Volume Properties 欄位選擇 Type:RAID 1 Change type。 3. 如有需要,您也可以在此變更 Name、Select the new volume type 與 Select additional disks to include in the new volume 這幾個項目。 4.
6.4.3 刪除 Volume 在操作此功能時請務必非常小心,所有在硬碟中的資料將被一併刪除, 如有需要請先備份檔案。 請依照以下步驟刪除 Volume: 1. 在主選單裡,點選在 Volume 欄位中欲刪除的 Volume(如以下畫面中顯 示的 Volume_0000)。 2. 然後點選 Volume Properties 欄位中的 Delete volume,則會顯示如下的 畫面。 3.
6.4.
6-38 第六章:磁碟陣列設定
第七章: 安裝驅動程式 在本章節中將介紹伺服器內的相關驅動程式的安 裝與設定說明。 7
7.1 安裝 RAID 驅動程序 當您在系統中創建好 RAID 陣列模式後,現在您就可以開始安裝操作系統 至獨立的硬盤設備或具開機功能的磁盤陣列。這章節將來介紹在安裝操作系 統的過程中如何安裝 RAID 控制器的驅動。 7.1.1 創建一張 RAID 驅動程序軟盤 本系統不含軟碟機。當您建立 RAID 驅動程式磁片時需要使用 USB 外接 式軟碟機。 當您使用 LSI Software RAID Configuration 工具程式建立 RAID 設定, SATA 光碟機的開機次序將需透過手動調整。否則,系統將不會透過 SATA 光碟機開機。 在 Windows® 中建立 RAID 驅動程式磁片: 1. 2. 3. 4. 5.
7.1.2 安裝 RAID 驅動程式 在 Windows® Server 2008 R2 系統安裝過程中安裝 您可在 Windows® Server 2008 R2 系統安裝過程中安裝 RAID 驅動程式: 1. 使用 Windows® Server 2008 R2 作業系統安裝光碟開機,並依照畫面的 指示開始安裝作業系統。 2. 當畫面跳出選擇安裝的類型時,請選擇 Custom (advanced)。 3.
4. 然後顯示訊息,提醒您放入 RAID 控制器驅動程式檔案。若您的系統裡 有僅只有一部光碟機,請先將 Windows 作業系統安裝光碟退出,並放入 驅動與公用程式 DVD 光碟,然後點選 Browse(瀏覽)。 5. 找到存放在驅動與公用程式光碟內的驅動程式,然後點選 OK 繼續。 6. 從清單中選擇您所要安裝的 RAID 控制器驅動程式,然後點選 Next。 7. 當系統載入 RAID 驅動程式後,請取出主機板驅動與公用程式光碟 並再 放入 Windows Server 作業系統安裝光碟,選擇驅動程式安裝至 Windows 並點選 Next。 8.
Red Hat® Enterprise Linux 5.x 作業系統 請依以下步驟在 Red Hat® Enterprise 作業系統安裝過程中安裝 RAID 驅動 程式: 1. 使用 Red Hat® 作業系統安裝光碟片啟動系統。 2. 然後於 boot: 後,輸入 linux dd noprobe=ata1 noprobe=ata2...,再按下 鍵。 注意:上述指令中的 ata 數量取決於用在建立 RAID 磁碟陣列的硬碟數 量。例如,若您想使用六個硬碟來建立 RAID 陣列,請輸入以下指令 列:linux dd noprobe=ata1 noprobe=ata2 noprobe=ata3 noprobe=ata4 noprobe=ata5 noprobe=ata6。 - To install or upgrade in graphical mode, press the key. - To install or upgrade in text mode, type: linux text .
5. 當詢問您是否增加其他額外的 RAID 控制器驅動程式時,選擇 No,然後 按下 鍵。 More Driver Disks? Do you wish to load any more driver disks? Yes No 6. 接著請依照系統的提示繼續完成作業系統的安裝。 7. 在安裝完成後,請先不要點選 Reboot。請先按下 + + 鍵,從圖形介面切換至指令列介面。 8. 若您所使用的是標準軟碟機,請在指令列介面輸入以下的指令: mkdir /mnt/driver mount /dev/fd0 /mnt/driver cd /mnt/driver sh replace_ahci.
Red Hat® Enterprise Linux OS 6.x 作業系統 在 Red Hat® Enterprise 作業系統環境下安裝 LSI MegaRAID 控制器驅動程 式: 1. 將系統透過 Red Hat® 作業系統安裝光碟開機。 2. 按下 鍵編輯選項。 3.
4. 當系統詢問您若要透過磁碟片安裝時,請按下 鍵選擇 Yes ,然後 按下 鍵繼續。 Main Menu Do you have a driver disk? Yes No 5. 當詢問驅動程式磁碟來源時,請按下 鍵切換選擇來源裝置。接著 再使用 鍵移至 OK 處,然後按下 鍵。 Driver Disk Sou8rce You have multiple devices which could serve as source for a driver disk.
6. 當出現此對話框時,請在 USB 介面軟碟機中放入 Red Hat Enterprise 的 RAID 驅動程式磁片,並選擇 OK,然後按下 鍵。 Insert Driver Disk Insert your driver disk into /dev/sdb and press “OK” to continue. OK Back 此時會開始安裝 RAID 驅動程式至系統中。 7. 當詢問您是否增加其他額外的 RAID 控制器驅動程式時,選擇 No,然後 按下 鍵。 More Driver Disks? Do you wish to load any more driver disks? Yes No 8.
準備 Linux 驅動程式 請準備另一部裝有使用 Linux 作業系統的電腦,以建立 RAID 驅動程式。 當建立 RAID 驅動程式時,您可以參考以下的方式使用 64位元 SUSE Linux 系統來建立一張 64位元 RAID 驅動程式,以供 SUSE11 sp1 作業系統使用。 1. 將映像檔複製到 Linux 系統中。 範例:megasr-15.00.0120.2012-1-sles11-ga-x86_64.img 2. 新增一個資料夾。 範例:image 3. 使用以下的指令,將映像檔載入映像檔資料夾中: mount -o loop [image file name] image 範例:mount -o loop megasr-15-15.00.0120.2012-1-sles11-ga-x86__64. img image 4. 將映像檔資料夾標示為 01,並複製至一個 FAT32 格式的 USB 儲存裝置 中。 5.
在 SUSE Linux 11 作業系統下安裝 請依照以下步驟,於 SUSE Linux Enterprise Server 作業系統下安裝 RAID 控制晶片的驅動程式: 1. 使用 SUSE 作業系統安裝光碟開機。 2. 使用方向鍵從 Boot Options 畫面中選擇 Installation 選項。 3.
4. 當出現對話框時,請在軟碟機中放入 RAID 驅動程式磁碟片,並在 Boot Options 欄位中輸入 brokenmodules=ahci,然後按下 鍵。 5. 當出現對話框時,選擇在安裝畫面中的 sda(選擇 USB 介面軟碟機)這 項,接著選擇 OK,然後按下 鍵。 Please choose the Driver Update medium. sda: USB Floppy Other device OK Back 6.
7.2 安裝應用程式與工具程式 本驅動及公用程式光碟裡提供您主機板相關的驅動程式、管理應用程式 與工具程式,可以讓您將主機板功能最佳化。 1. 驅動及公用程式 DVD 光碟裡的內容如有變更,恕不另行通知。請造 訪華碩網站(tw.asus.com)以更新最新的軟體與工具程式。 2. 驅動及公用程式 DVD 光碟為支援使用於 Windows® Server 2008 R2 和 Windows® Server 2012 作業系統。 7.3 使用驅動及公用程式 DVD 光碟 於光碟機中放入主機板/系統的驅動程式光碟。若您已經啟動光碟自動偵 測的功能,透過作業系統自動偵測的功能,接著會自行啟動光碟並顯示預設 的 Drivers(驅動程式)標籤頁。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 DVD 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 在驅動及公用程式 DVD 光碟的主選單裡有以下幾個標籤頁: 1. 2. 3. 4. 5.
7.3.1 驅動程式主選單 驅動程式主選單提供了您目前需要安裝的一些硬體驅動程式,請安裝必 要的驅動程式來啟動您系統上的硬體。 7.3.
7.3.3 製作驅動程式磁片選單 MakeDisk 選單提供您目前所需要的驅動程式項目。點選您所需要的驅動 程式以進行製作。 您可以點選畫面下方的箭頭,以顯示其他的 MakeDisk 項目。 7.3.
7.3.
7.4 安裝 Intel 晶片裝置軟體程式 本章節提供您如何安裝在 Intle 晶片環境中的隨插即用裝置元件。 您需要在 Windows® 作業系統環境中,手動安裝 Intel® 晶片裝置軟體。 請依照以下步驟,在 Windows® Server 2008 R2 作業系統下安裝 Intel® 晶 片裝置軟體程式: 1. 重新啟動電腦,使用 Administrator(主管理者)身分登入作業系統。 2. 將驅動及公用程式 DVD 光碟放入光碟機中。 若您已經啟動光碟自動偵測的功能,透過作業系統自動偵測的功能,會 自行啟動光碟顯示 Drivers (驅動程式)選單畫面。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 DVD 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 3. 選擇 Intel Chipset Device Software 後,開始進行安裝。 4.
5. 當顯示 License Agreement(授權同意)說明時,請點選 Yes 繼續。 6. 在瀏覽並且閱讀 Readme File Information 後,請點選 Next 繼續安裝。 7.
7.5 安裝Intel® I350-AM1/I350-AM2/I210/ X540-BT2 Gigabit 網路驅動程式 本節介紹如何安裝 Intel® I350-AM1/I350-AM2/I210/X540-BT2 Gigabit 驅 動程式至系統中。 請依照以下的步驟,在 Windows® 作業系統中,安裝網路驅動程式: 1. 重新開機。 2. 使用 Administrator(主管理者)身分登入作業系統。 3. 將驅動及公用程式 DVD 光碟放入光碟機中。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 DVD 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 4. 點選 Drivers(驅動程式)選單中的 Intel I350-AM1/I350-AM2/I210/ X540-BT2 Gigabit Drivers 選項,開始進行安裝。 5.
6. 當顯示 Welcome to InstallShield Wizard for Intel(R) Network 安裝精靈 畫面時,請點選 Next 繼續。 7. 然後勾選 I accept the terms in the license agreement,再點選 Next 同 意授權後繼續。 8.
9. 點選 Install 開始安裝。 10.
7.6 安裝顯示驅動程式 這裡將介紹如何安裝 ASPEED® 圖形顯示介面(VGA)驅動程式。 您需要在 Windows® Server 系統中,手動安裝 ASPEED 圖形顯示介面驅動 程式。 請依照以下步驟,在 Windows® 作業系統中安裝 ASPEED 圖形顯示介面驅 動程式: 1. 重新開機,並使用 Administrator(主管理者)登入作業系統。 2. 將驅動及公用程式 DVD 光碟放入光碟機中。 若您已經啟動光碟自動偵測的功能,透過作業系統自動偵測的功能,會 自行啟動光碟顯示 Drivers (驅動程式)選單畫面。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 DVD 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 3. 點選在 Drivers(驅動程式)選單裡的 ASPEED AST2300/AST2400 Display Driver 開始進行。 4.
5. 點選 Install 開始安裝。 6.
7.7 安裝 Intel® Rapid Storage Technology enterprise 4.0 程式 本節將介紹如何安裝 Intel® Rapid Storage Technology enterprise 4.0 程 式。 您需要在 Windows Server 系統中,以手動方式安裝 Intel® Rapid Storage Technology enterprise 4.0 程式。 請依照以下步驟安裝程式: 1. 重新開機,使用 Administrator(主管理者)登入 Windows 系統。 2. 於光碟機中放入主機板/系統所附的驅動與公用程式光碟片,若您的系統 已經啟動了光碟機「自動安插通知」的功能,那麼稍後一會光碟片會自 動顯示 Drivers 選單(驅動程式選單)視窗。 若歡迎視窗並未自動出現,那麼請瀏覽光碟的檔案內容,找到存在 BIN 檔案夾裡的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程式來開啟 選單。 3. 點選 Intel Rapid Storage Technology enterprise 4.0 開始安裝。 4.
5. 讀取警示資訊後,點選 Next 繼續。 6. 選擇 Yes 接受許可同意條款,並且繼續安裝進程。 7.
8. 在完成安裝時,點選 Next 完成安裝作業。 9.
附錄 本附錄為提供您參考的相關聯絡資訊。
華碩的聯絡資訊 華碩電腦公司 ASUSTeK COMPUTER INC.(台灣) 市場訊息 地址 :台灣臺北市北投區立德路 150 號 4 樓 電話 :+886-2-2894-3447 傳真 :+886-2-2890-7798 網址 :http://www.asus.com/tw/ 技術支援 電話 線上支援 :+886-2-2894-3447(0800-093-456) : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-tw ASUS COMPUTER INTERNATIONAL(美國) 市場訊息 地址 :800 Corporate Way, Fremont, CA 94539, USA 傳真 :+1-510-608-4555 網址 :http://www.asus.com/us/ 技術支援 電話 :+1-812-282-2787 傳真 :+1-812-284-0883 線上支援 : h ttps://www.asus.
華碩電腦(上海)有限公司 ASUSTEK COMPUTER(SHANGHAI)CO., LTD. 市場訊息 地址 : 上海市閔行區金都路 5077 號 電話 :+86-21-5442-1616 傳真 :+86-21-5442-0099 網址 :http://www.asus.com.cn 技術支援 電話 線上支援 :+86-20-2804-7506(400-620-6655) : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-cn ASUS Czech Service s.r.o.(歐洲) 市場訊息 地址 :Na Rovince 887, 720 00 Ostrava – Hrabová, Czech Republic 傳真 :+420-596766888 網址 :http://www.asus.com/cz/ 技術支援 電話 :+420-596-766-891 傳真 :+420-596-766-329 電子信箱 :advance.rma.eu@asus.
ASUS Holland BV(荷蘭) 市場訊息 地址 網址 :Marconistraat 2, 7825GD EMMEN, The Netherlands :http://www.asus.com/nl/ 技術支援 電話 :+31-(0)591-5-70292 傳真 :+31-(0)591-666853 電子信箱 :advance.rma.eu@asus.com 線上支援 : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=nl-nl ASUS Polska Sp. z o.o.(波蘭) 市場訊息 地址 網址 技術支援 電話 線上支援 :Ul. Postępu 6, 02-676 Warszawa, Poland :http://www.asus.com/pl/ :+48-225718033 : https://www.asus.