RS720A-E11-RS12E 2U 機架式伺服器 使用手冊
T23203 4.00 版 2024 年 1 月發行 版權說明 ©ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項.................................................................................................................................... vi 用電安全............................................................................................................................................vii 電磁安全................................................................................................................................vii 靜電元件...............................................................................
目錄 2.6.8 安裝華碩 PIKE II 卡...........................................................................................2-46 2.6.9 安裝 M.2(NGFF)擴充卡..............................................................................2-50 2.6.10 設定擴充卡.........................................................................................................2-51 2.7 連接排線................................................................................................................................2-52 2.8 SATA/SAS 背板排線的連接......
目錄 5.5.2 PSP 韌體版本.......................................................................................................5-13 5.5.3 APM..........................................................................................................................5-13 5.5.4 Onboard LAN 設定..............................................................................................5-14 5.5.5 序列埠控制面板重新定向(Serial Port Console Redirection)......5-15 5.5.6 CPU 設定...........................................................
使用注意事項 操作伺服器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照使用手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 伺服器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用伺服器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項周邊設備是否都已經連接妥當再開機。 ‧ 避免邊吃東西邊使用伺服器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近伺服器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入伺服器機件內,以避免引起機件短路,或是電路損毀。 ‧ 伺服器開機一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除周邊產品時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移伺服器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的訊號線之前,請先拔掉連接的電源線,或是先安裝訊號線 之後再安裝電源線。 ‧ 使用一隻手拆裝訊號線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊產生。 ‧ 伺服器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、記憶體、主機板、介面卡、磁碟機、硬碟機等設備,是由許多精密的積體 電路與其它元件所構成,這些積體電路很容易因為遭受靜電的影響而損壞。因此,在 拆裝任何元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝伺服器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與伺服器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸伺服器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜
關於本使用手冊 本使用手冊主要是針對有經驗且具有個人電腦硬體組裝知識的使用者所撰寫的。本 手冊可以幫助您建立起最新、功能強大的 RS720A-E11-RS12E 華碩伺服器。手冊內 容介紹本產品各部份元件的拆裝、設定,因此,部份元件可能是選購配備,並未包含 在您的產品當中,假如您有需要選購該配備,請向本公司授權經銷商洽詢。 章節說明 本使用手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖示帶您認識華碩伺服器的功能及特色,包括系統的前、後面板以及 內部功能的介紹。 第二章:硬體安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本伺服器裡 頭。 第三章:進階安裝 本章提供本伺服器的機架安裝及使用方法。 第四章:主機板資訊 本章提供本伺服器內建主機板的相關資訊,包括主機板的構造圖、跳線設定及連接 埠位置等。 第五章:BIOS 程式設定 本章提供伺服器之 BIOS 的升級與管理及 BIOS 設定的相關訊息。 第六章:安裝驅動程式 本章提供主機板相關之驅動程式的安裝說明。 附錄 在本附錄裡將列出相關的聯絡資訊。 viii
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主機板元件。不當的 動作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照使用手冊所描述之方式 完成一項或多項軟硬體的安裝或設定。 說明:小祕訣,名詞解釋,或是進一步的資訊說明。提供有助於完成某 項工作的訣竅和其他額外的資訊。 哪裡可以找到更多的產品資訊 您可以經由下面所提供的兩個管道來獲得您所使用的華碩產品資訊以及軟硬體的升 級資訊等。 1. 華碩網站 您可以到 https://www.asus.com/tw/ 華碩電腦全球資訊網,來取得所有關於華碩軟硬 體產品的各項資訊。 2. ASUS Control Center(ACC)使用手冊 本使用手冊介紹如何設定並使用華碩伺服器管理工具,請至 asuscontrolcenter.asus.
產品之限用物質含有情況 「產品之限用物質含有情況」之相關資訊,請參考下表。 單元 鉛 (Pb) 汞 (Hg) 限用物質及其化學符號 六價鉻 鎘 (Cd) (Cr+6) 印刷電路板及其 o o o 電子組件 外殼 o o o o 散熱設備 o o o 電源供應器 o o o 其他及其配件 o o o 備考 1 "o" 係指該項限用物質之百分比含量未超出百分比含量基準值。 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o o o o o o o o 備考 2 "-" 係指該項限用物質為排除項目。 產品回收與處理 華碩與資源回收業者以最高標準相互配合,以保護我們的環境,確保工作者的安 全,以及遵從全球有關環境保護的法律規定。我們保證以資源回收的方式回收以往生 產的舊設備,透過多樣的方式保護環境。 如欲了解更多關於華碩產品資源回收資訊與聯絡方式,請連線上網至 CSR(Corporate Social Responsibility)網頁:http://csr.asus.com/english/Takeback.
第一章: 系統導覽 本章以清楚的圖示帶您認識華碩伺服器的功能及特色, 包括系統的前、後面板以及內部功能的介紹。 1
1.1 產品包裝內容 以下為本伺服器包裝內的組件。 標準元件 機種型號 RS720A-E11-RS12E 機殼 華碩 R2P-A-R22475 2U 機架式機殼 主機板 華碩 KMPP-D32 伺服器主機板 硬體元件 1 x 1600W 80PLUS Platinum 電源供應器或 1 x 2400W 80PLUS Titanium 電源供應器 12 x 可熱抽換 2.5 / 3.5 吋儲存裝置抽取架 1 x 前側 I/O 面板 4 x 系統風扇 配件 1 x AMD EPYC™ 驅動與公用程式光碟片 螺絲一包 2 x 處理器散熱片 2 x AC 電源線 選配配件 1 x 備援式 1600W 80PLUS Platinum 電源供應器模組或 1 x 備援式 2400W 80PLUS Titanium 電源供應器模組(第二組) 1 x 標準式機架安裝套件 若以上列出的任何一項配件有損壞或是短缺的情形,請儘速與您的經銷 商連絡。 1.
1.3 產品規格表 華碩 RS720A-E11-RS12E 是一款精心打造的 2U 伺服器,內裝 KMPP-D32 伺服器 主機板,支援 AMD EPYC™ 7002 / 7003 系列處理器,並包含最新單晶片系統所提供 的相關技術。 機種型號 RS720A-E11-RS12E 中央處理器 / 系統匯流排 2 x Socket SP3(LGA 4094) AMD EPYC™ 7002 / 7003 系列 xGMI(外置全局記憶體介面連接) 核心邏輯 系統單晶片(SoC) 總插槽數 32(每個 CPU 8 通道;每個 CPU 16 個記憶體模組) 擴充容量 最高可擴充達 4096GB 記憶體類型 * 請參考華碩官方網站 https://www.asus.
機種型號 RS720A-E11-RS12E 12 x 可熱抽換 2.5 / 3.5 吋儲存裝置插槽 (最多 8 x NVMe/SATA*/SAS*+4 x SATA*/SAS* ) I = 內建 A 或 S = 可熱 抽換 * 僅在搭配選配 HBA/RAID 卡時支援 SATA & SAS 功能 * 支援 tri-mode 卡 後側插槽(選配): 2 x 可熱抽換 2.5 吋儲存裝置插槽(NVMe) 儲存裝置插槽 主機板內建插 槽 2 x M.
RS720A-E11-RS12E 機種型號 管理解決方案 外部遠端遙控 硬體 軟體 支援作業系統 內建 ASMB10-iKVM ,支援 KVM-over-IP 的方式 ASUS Control Center(Classic) Windows® Server 2019 RedHat® Enterprise Linux SuSE® Linux Enterprise Server CentOS Ubuntu VMware * 請參考華碩官方網站 https://www.asus.com/tw/ 以查詢最新的 作業系統支援版本 安裝認證標準 BSMI、CE、C-Tick、FCC(ClassA) 尺寸(深 x 寬 x 高) 淨重(不包含處理器、記憶體與儲 存裝置) 毛重(不包含處理器、記憶體、儲 存裝置;包含外包裝) 840 mm x 449 mm x 88.1 mm(2U) 18.195 公斤 23.
1.4 前端面板 本伺服器的前端面板提供了簡單的存取功能,包括相關的 LED 指示燈、USB 連接 埠等,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7 顯示燈號說明。 USB 3.2 Gen 1 連接埠 前面板 LED 指示燈與按鈕 1 2 3 4 RESET 拉柄 12 x 2.5/3.5 吋儲存裝置插槽 拉柄 1.5 後端面板 後端面板包含了所有連接裝置的接頭、輸出/輸入連接埠與系統電源插孔等。下圖 即為伺服器後端面板圖示。 標準機種 / GPU 機種 擴充卡插槽 電源供應器模組 電源線連接孔 電源按鈕 Q-Code 指示燈 Location 按鈕 擴充卡插槽 擴充卡插槽 選配外接風扇 (GPU 機種) 選配網路埠 DM 管理網路埠* USB 3.2 Gen 1 連接埠 顯示器連接埠 ‧ * 本網路埠僅供 ASMB10-iKVM 使用。 ‧ Q-Code 指示燈以錯誤代碼提示可能的情況,以便進行疑難排解。發 生錯誤原因會依實際情況而異。 ‧ 詳細內容請參考 1.7.
標準機種搭載後端面板插槽 2 x 2.5 吋儲存裝置插槽 擴充卡插槽 擴充卡插槽 電源供應器模組 電源線連接孔 電源按鈕 Q-Code 指示燈 選配網路埠 DM 管理網路埠* USB 3.2 Gen 1 連接埠 顯示器連接埠 Location 按鈕 擴充卡插槽 ‧ * 本網路埠僅供 ASMB10-iKVM 使用。 ‧ Q-Code 指示燈以錯誤代碼提示可能的情況,以便進行疑難排解。發 生錯誤原因會依實際情況而異。 ‧ 詳細內容請參考 1.7.
1.6 內部組件 下圖即為本伺服器的標準內部組件: 標準機種 1. 轉接卡托架 2. 電源供應器(隱藏) 3. 華碩 KMPP-D32 伺服器主機板 4. 系統風扇 5. SATA/SAS/NVMe 背板 6. 前端面板(隱藏) 7. 12 x 2.5 / 3.
標準機種搭載後端面板插槽 1. 轉接卡托架 2. 電源供應器(隱藏) 3. 2 x 2.5 吋儲存裝置插槽 4. 華碩 KMPP-D32 伺服器主機板 5. 系統風扇 6. SATA/SAS/NVMe 背板 7. 前端面板(隱藏) 8. 12 x 2.5 / 3.
GPU 機種 1. 轉接卡托架 2. 電源供應器(隱藏) 3. 華碩 KMPP-D32 伺服器主機板 4. 系統風扇 5. SATA/SAS/NVMe 背板 6. 前端面板(隱藏) 7. 12 x 2.5 / 3.5 吋儲存裝置插槽 8.
1.7 LED 顯示燈號說明 1.7.
1.7.
1.7.
1.7.
Action PSP Boot PHASE POST CODE TYPE DESCRIPTION PSP Boot Loader phase (Error Post Codes) 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error HMAC-SHA256 operation fail - internal status Booted from boot
Action PHASE PSP Boot PSP Boot Loader phase (Error Post Codes) POST CODE 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5E 0x5F TYPE Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error DESCRIPTION Function RunPostX86ReleaseUnitTests failed in memcmp() Interface between PS
Action PSP Boot PHASE PSP Boot Loader phase (Error Post Codes) POST CODE 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 TYPE Error Error Error Error Error Error Error Error 0x68 Error 0x69 0x6A 0x6B Error Error Error 0x6C Error DESCRIPTION VMG Storage Init failed Failure in mbedTLS user app An error occured whilst attempting to SMN map a fuse register Fuse burn sequence/operation failed due to internal SOC error Fuse sense operation timed out Fuse burn sequence/operation timed out waiting for burn done
Action PHASE PSP Boot PSP Boot Loader phase (Status Post Codes) POST CODE 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progres
Action PHASE PSP Boot PSP Boot Loader phase (Status Post Codes) POST CODE 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress DESCRIPTION Successfully entered WarmBootResume() Successfully
Action PHASE PEI(Pre-EFI Initialization) phase Quick VGA DXE(Driver Execution Environment) phase Normal boot BDS(Boot Device Selection) phase POST CODE 0x10 0x11 0x15 0x19 0x32 0x33 0x34 0x35 0x36 0x37 0x3B 0x4F 0x60 0x61 0x62 0x63 0x68 0x69 0x6A 0x70 0x71 0x72 0x78 0x79 0xD0 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress P
Action Normal boot PHASE BDS(Boot Device Selection) phase Operating system phase POST CODE 0xb2 0xb3 0xb4 0xb6 0xb7 0xA0 0xA1 0xA2 0xA3 0x00~0xFF 0xA8 0xA9 0xAB 0xAD 0xAE 0xAA 0xAC TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress DESCRIPTION Legacy Option ROM Initialization Reset system USB hotplug NVRAM clean up NVRAM configuration reset IDE, AHCI Initialization IDE, AHCI Initialization IDE,
AMD EPYC™ 7003 系列處理器 Action PHASE SEC Start up Security Phase PSP Boot PSP Boot Loader phase (Error Post Codes) POST CODE 0x01 0x02 0x03 0x04 0x05 0x06 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F TYPE Progress Progress Progress Progress Progress Progress error error error error error error error error error error error error error error error error error error error error error error err
Action PHASE PSP Boot PSP Boot Loader phase (Error Post Codes) POST CODE 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 TYPE error error error error error error error error error error error error error error error error error error error error error error error error error error DESCRIPTION HMAC-SHA256/384 operation fail - internal status Booted from boot source not recognized by PSP PSP directory entry not found PSP f
Action PSP Boot PHASE PSP Boot Loader phase (Error Post Codes) POST CODE 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 TYPE error error error error error error error error error error 0x44 error 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5E 0x5F error error error error error error error error error error error error error error error error error error error error error error error error error error DESCRIPTION Unabl
Action PSP Boot PHASE PSP Boot Loader phase (Error Post Codes) POST CODE 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 TYPE error error error error error error error error 0x68 error 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A error error error error error error error error error error error error error error error error error DESCRIPTION VMG Storage Init failed failure in mbedTLS user app An error occured whilst attempting to SMN map a fuse register Fuse burn se
Action PSP Boot PHASE PSP Boot Loader phase (Status Post Codes) POST CODE TYPE 0x7B error DESCRIPTION 0x7C error Platform Vendor ID and/or Model ID binding violation 0x7D error Bootloader detects BIOS request boot from SPI-ROM, which is unsupported for PSB.
Action PHASE PEI(Pre-EFI Initialization) phase Quick VGA DXE(Driver Execution Environment) phase POST CODE TYPE DESCRIPTION 0x10 0x11 0x15 0x19 0x32 0x33 0x34 0x35 0x36 0x37 0x3B 0x4F 0x60 0x61 0x62 0x63 0x68 0x69 0x6A 0x70 0x71 0x72 0x78 0x79 0xD0 Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress PEI Core Entry PEI cache as ra
Action PHASE BDS(Boot Device Selection) phase Normal boot Operating system phase 1-28 第一章:系統導覽 POST CODE TYPE DESCRIPTION 0x90 Progress BDS started 0x91 Progress Connect device event 0x92 Progress PCI Bus Enumeration 0x93 Progress PCI Bus Enumeration 0x94 Progress PCI Bus Enumeration 0x95 Progress PCI Bus Enumeration 0x96 Progress PCI Bus Enumeration 0x97 Progress Console outout connect event 0x98 Progress Console input connect event 0x99 Progress AMI Super IO start 0x9
第二章: 硬體安裝 本章以逐步說明的方式,教您如何將系統所需的零組件 正確地安裝至本伺服器裡頭。 2
2.1 機殼上蓋 打開機殼後半部上蓋 1. 使用螺絲起子鬆開機殼兩側的 2 顆螺絲。 2. 按下機殼上的按鈕。 3. 將機殼上蓋向後推,使之鬆開脫離機殼。 4.
打開中間機殼上蓋 1. 使用螺絲起子鬆開機殼兩側的 2 顆螺絲。 2. 按下機殼上的按鈕。 3. 將機殼上蓋向後推,使之鬆開脫離機殼。 4.
2.2 導風罩 標準機種 請依照以下步驟移除導風罩: 1. 使用螺絲起子鬆開固定導風罩的 2 顆螺絲。 2. 將導風罩由機殼內垂直取出。 請依照以下步驟安裝導風罩: 1. 將導風罩對齊記憶體插槽邊緣並安裝,使之固定於機殼內。 2.
GPU 機種 請依照以下步驟移除導風罩: 1. 使用螺絲起子鬆開固定導風罩的 4 顆螺絲。 2.
請依照以下步驟安裝導風罩: 1. 將導風罩對齊記憶體插槽邊緣並安裝,使之固定於機殼內。 2.
2.3 中央處理器(CPU) 本主機板具備 Socket SP3 處理器插槽,本插槽是專為 AMD EPYC™ 7002 / 7003 系列處理器所設計。 • 在您購買本主機板之後,請確認在處理器插座上附有一個 PnP 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保護 蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在 安 裝 完 主 機 板 之 後 , 請 將 隨 插 即 用 的 保 護 蓋 保 留 下 來 。 只 有 在 S o c k e t S P3 插槽上附有隨插即用保護蓋的主機板符合 R e t u r n Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理 產品的維修與保固。 • 本保固不包括處理器插座因遺失、錯誤的安裝或不正確的移除隨插即 用保護蓋所造成的毀損。 2.3.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 依照 2.1 機殼上蓋 的說明移除後端上蓋板。 2. 依照 2.2 導風罩 的說明移除導風罩。 3. 鬆開固定安裝盒上蓋的螺絲。 4.
5. 向上滑出外蓋,由邊框內取出。 外蓋 邊框 保護蓋 6. 將裝有 C P U 的托架安裝至邊框 內,並移除保護蓋。 裝有 CPU 的托架只能以 單一方向正確地安裝到邊 框。切記請勿用力地將裝 有 CPU 的托架以錯誤的 方向進行安裝。 7.
8. 將安裝盒上蓋的三個螺絲使用螺絲起子 分別鎖上。 安裝盒上蓋螺絲規格為 T20, 扭矩值建議為 16.1±1.2 kgf-cm (14.0±1.0 lbf-in)。 9. 將散熱器上的四個螺絲,使用十字螺絲 起子分別鎖上,使散熱器固定於主機板 上。將四個螺絲使用螺絲起子依對角的 鎖定方式分別鎖上,使散熱器穩固於主 機板上。 安裝盒上蓋螺絲規格為 T20, 扭矩值建議為 16.1±1.2 kgf-cm (14.0±1.0 lbf-in)。 10. 依照 2.
2.4 系統記憶體 2.4.
2.4.
2.4.3 安裝記憶體模組 安裝記憶體模組前,請確認已安裝中央處理器、散熱器與導風罩。 請依照下面步驟安裝記憶體模組: 1. 先將記憶體模組插槽的固定卡榫扳 開。 2. 將記憶體模組的金手指對齊記憶體模 組插槽的溝槽,並且在方向上要注意 金手指的缺口要對準插槽的凸起點。 記憶體模組缺口 插槽凸起點 往外扳開記憶體模 組插槽的卡榫 記憶體插槽上的凹槽為設計僅一個方向供記憶體模組插入,請在裝入 前,確定記憶體模組與記憶體插槽上的安裝方向是契合的。 3. 最後緩緩將記憶體模組插入插槽中, 若無錯誤,插槽的卡榫會因記憶體模 組置入而自動扣到記憶體模組的凹孔 中。 卡榫會在記憶體模組 正確置入後自動扣上 請將記憶體模組缺口對準插槽的凸起點並垂直插入,以免造成記憶體模 組缺口損壞。 2.4.4 取出記憶體模組 請依照以下步驟取出記憶體模組: 1. 依照 2.1 機殼上蓋 的說明移除後端上 蓋板。 2. 壓下記憶體模組插槽的固定卡榫以鬆開 記憶體模組。 3.
2.
請按照以下的步驟,安裝 3.5 吋熱抽換 SATA/SAS 儲存裝置: 1. 請先將握把上的固定扣朝上方撥開,以便將硬碟槽握把鬆開。 握把 2. 將握把朝外扳開時,硬碟槽便會 向外滑出,請順勢將硬碟擴充槽 往主機的前方抽離。 3. 將硬碟槽放置在平坦桌面上。 4. 取出準備安裝的儲存裝置與螺絲 配件。 5.
6. 當儲存裝置安裝完畢後,請以手 緊握住硬碟槽握把置入系統的 插槽中,將其輕推至機殼底部 (A),最後請將板手輕輕地推 回原位並輕扣固定,使硬碟槽能 夠緊密地固定在機殼中(B)。 7.
請按照以下的步驟,安裝 2.5 吋熱抽換 SATA/SAS 儲存裝置: 1. 請先將握把上的固定扣朝上方撥開,以便將硬碟槽握把鬆開。 握把 2. 將握把朝外扳開時,硬碟槽便會 向外滑出,請順勢將硬碟擴充槽 往主機的前方抽離。 3. 將硬碟槽放置在平坦桌面上。 4. 取出準備安裝的儲存裝置與螺絲 配件。 5.
6. 當儲存裝置安裝完畢後,請以手 緊握住硬碟槽握把置入系統的 插槽中,將其輕推至機殼底部 (A),最後請將板手輕輕地推 回原位並輕扣固定,使硬碟槽能 夠緊密地固定在機殼中(B)。 7.
2.6 擴充插槽 本伺服器已預先安裝四組轉接卡以支援八個 PCIe 插槽與一個 OCP Mezzanine 插 槽。 標準機種 / GPU 機種 轉接卡 4 轉接卡 2 轉接卡 3 轉接卡 1 OCP 3.0 適配器 標準機種搭載後端面板插槽 2 x 2.5 吋儲存裝置插槽 轉接卡 2 轉接卡 3 2-18 第二章:硬體安裝 轉接卡 1 OCP 3.
2.6.1 安裝擴充卡至轉接卡支撐架 1 請按照以下步驟安裝擴充卡至轉接卡支撐架 1: 1. 鬆開固定轉接卡支撐架 1 於機殼上的指旋螺絲。 2. 使用雙手握住轉接卡支撐架 1 的兩端,再將其從主機板的 PCIE 插槽中取出。 3.
4. 將轉接卡支撐架 1 以下圖所示方向擺放在平坦桌面上。 5. 撥開金屬托架鎖。 6. 安裝 PCIE 擴充卡至轉接卡支撐架 1。 7.
8. 重新連接轉接卡支撐架 1 連接的排線。 9. 重新安裝轉接卡支撐架 1 至主機板。 10.
2.6.2 安裝擴充卡至轉接卡支撐架 2 請按照以下步驟安裝擴充卡至轉接卡支撐架 2: 1. 鬆開固定轉接卡支撐架 2 於機殼上的指旋螺絲。 2. 鬆開固定轉接卡支撐架 2 於主機板上的指旋螺絲。 3. 使用雙手握住轉接卡支撐架 2 的兩端,再將其從主機板的 PCIE 插槽中取出。 4.
5. 將轉接卡支撐架 2 以下圖所示方向擺放在平坦桌面上。 6. 撥開金屬托架鎖。 7. 安裝 PCIE 擴充卡至轉接卡支撐架 2。 8.
9. 重新連接轉接卡支撐架 2 連接的排線。 10. 重新安裝轉接卡支撐架 2 至主機板。 11. 鎖上步驟 1 移除的指旋螺絲,固定轉接卡支撐架 2 至機殼。 12.
2.6.3 安裝擴充卡至轉接卡支撐架 3 請按照以下步驟安裝擴充卡至轉接卡支撐架 3: 1. 鬆開固定轉接卡支撐架 3 於機殼上的指旋螺絲。 2. 鬆開固定轉接卡支撐架 3 於主機板上的指旋螺絲。 3. 使用雙手握住轉接卡支撐架 3 的兩端,再將其從主機板的 PCIE 插槽中取出。 4.
5. 將轉接卡支撐架 3 以下圖所示方向擺放在平坦桌面上。 6. 撥開金屬托架鎖。 7. 安裝 PCIE 擴充卡至轉接卡支撐架 3。 8.
9. 重新連接轉接卡支撐架 3 連接的排線。 10. 重新安裝轉接卡支撐架 3 至主機板。 11. 鎖上步驟 1 移除的指旋螺絲,固定轉接卡支撐架 3 至機殼。 12.
2.6.4 安裝擴充卡至轉接卡支撐架 4 請按照以下步驟安裝擴充卡至轉接卡支撐架 4: 1. 鬆開固定轉接卡支撐架 4 於機殼上的指旋螺絲。 2.
3. 將轉接卡支撐架 4 翻面並移除金屬擋板。 4.
5. 重新安裝轉接卡支撐架 4 至主機板。 6.
2.6.5 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至轉接卡支撐架 建議您將 OCP 3.0 插槽基板安裝至轉接卡支撐架 1 上的 PCIE2 插槽。 請依照以下步驟 安裝 OCP 3.0 插槽基板與 OCP 3.0 卡至轉接卡支撐架: 1. 鬆開固定轉接卡支撐架於機殼上的指旋螺絲。 2.
3. 移除轉接卡支撐架連接的排線。 4. 將轉接卡支撐架以下圖所示方向擺放在平坦桌面上。 5. 撥開金屬托架鎖。 6. 安裝OCP 3.0 插槽基板至轉接卡支撐架上的 PCIE2 插槽。 7.
8. 由 PCIe 轉接卡支撐架後方將 OCP 3.0 卡安裝至 OCP 3.0 插槽,確認 OCP 3.0 卡 上的金手指部分已完全沒入插槽內。 9. 安裝 OCP 3.0 卡後,將金屬托架鎖扣上,以將 OCP 3.0 卡固定於 PCIe 轉接卡支 撐架上。 10.
11. 重新安裝轉接卡支撐架至主機板。 12.
2.6.6 安裝乙太網路擴充卡至轉接卡支撐架 預先安裝的轉接卡支撐架可支援四埠或雙埠網路控制器擴充卡。 若您想要安裝後側外接風扇時,請勿安裝四埠網路控制器擴充卡。 請依照以下步驟安裝四埠或雙埠 網路控制器擴充卡: 1. 依照 2.6.4 安裝擴充卡至轉接卡支撐架 4 的步驟 1-2,由機殼上移除轉接卡支撐 架。 2. 將轉接卡支撐架翻面,安裝四埠或雙埠網路控制器擴充卡至 P C I E_L A N1 插槽 (A),並鎖上 2 顆螺絲固定(B)。 雙埠網路控制器擴充卡 3. 四埠網路控制器擴充卡 依照 2.6.
2.6.7 安裝 GPU 卡(選配) 請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 1: 1. 鬆開固定轉接卡支撐架 1 於機殼上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 1 的兩 端,再將其從主機板的 PCIE 插槽中 取出。 3.
4. 將轉接卡支撐架 1 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9.
10. 取出準備安裝的另一張 GPU 卡。 11. 安裝 GPU 卡至轉接卡支撐架 1。 12. 鎖上螺絲固定 GPU 導風罩。 13. 連接電源排線至 GPU 卡。 14.
15. 重新連接轉接卡支撐架 1 的排線。 16. 安裝轉接卡支撐架與 GPU 卡至 主機板的 PCIE 插槽,確認轉接 卡支撐架 1 上的金手指部分已 完全沒入插槽內。 17.
請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 2: 1. 鬆開固定轉接卡支撐架 2 於機殼上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 2 的兩 端,再將其從主機板的 PCIE 插槽中 取出。 3.
4. 將轉接卡支撐架 2 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9. 安裝 GPU 卡至轉接卡支撐架 2。 10.
11. 重新連接轉接卡支撐架 2 的排線。 12. 安裝轉接卡支撐架與 GPU 卡至 主機板的 PCIE 插槽,確認轉接 卡支撐架 2 上的金手指部分已 完全沒入插槽內。 13.
請按照以下步驟安裝 GPU(FH/FL)卡至轉接卡支撐架 3: 1. 鬆開固定轉接卡支撐架 3 於機殼上的 指旋螺絲。 2. 使用雙手握住轉接卡支撐架 3 的兩 端,再將其從主機板的 PCIE 插槽中 取出。 3.
4. 將轉接卡支撐架 3 以下圖所示方向擺放在平坦桌面上。 5. 取出準備安裝的 GPU 卡。 6. 連接電源排線至 GPU 卡,並確認排線穿過 GPU 導風罩。 7. 鎖上螺絲固定 GPU 導風罩。 8. 撥開金屬托架鎖。 9. 安裝 GPU 卡至轉接卡支撐架 3。 10.
11. 重新連接轉接卡支撐架 3 的排線。 12. 安裝轉接卡支撐架與 GPU 卡至 主機板的 PCIE 插槽,確認轉接 卡支撐架 3 上的金手指部分已 完全沒入插槽內。 13.
2.6.8 安裝華碩 PIKE II 卡 您可以更換預先安裝的華碩 PIKE II 卡以支援使用 SAS 儲存裝置。 請按照以下步驟更換預先安裝的華碩 PIKE II 卡: 1. 鬆開固定轉接卡支撐架於機殼上的指旋螺絲。 2.
3. 將轉接卡支撐架以下圖所示方向擺放在平坦桌面上。 4. 撥開金屬托架鎖。 5. 由轉接卡支撐架上移除華碩 PIKE II 卡。 6.
請按照以下步驟安裝華碩 PIKE II 卡: 1. 取出準備安裝的華碩 PIKE II 卡。 2. 安裝華碩 PIKE II 卡至轉接卡支撐架的 PCIe 插槽。 3. 將金屬托架鎖扣上,以將華碩 PIKE II 卡固定於轉接卡支撐架。 4.
5. 安裝轉接卡支撐架至主機板。 6. 鎖上步驟 1 移除的指旋螺絲,固定轉接卡支撐架。 7.
2.6.9 安裝 M.2(NGFF)擴充卡 請依照以下的步驟安裝 M.2(NGFF)擴充卡: 1. 找到主機板上的 M.2(標示 NGFF1 或 NGFF2)插槽。 2. (選配) 將螺絲座與上面的螺絲移除,並放置於一旁。 3. 在主機板上選擇欲安裝的 M.2 卡的螺絲孔位置,並鎖上螺絲座。 4. 將 M.2 擴充卡對準主機板上的 M.
2.6.10 設定擴充卡 1. 安裝好擴充卡之後,接著須藉由軟體設定來調整擴充卡的相關設定。 啟動電腦,然後更改必要的 BIOS 程式設定。若需要的話,您也可以參閱第五章 BIOS 程式設定以獲得更多資訊。 2. 為加入的擴充卡指派一組尚未被系統使用到的 IRQ。請參閱下表中所列出的中斷 要求使用一覽表。 3.
2.7 連接排線 ‧ 系統內的排線在出廠前都已經預先連接妥當。您不需再另外安裝,除 非您需要更換或安裝增加的硬體,才需要重新連接/移除。 ‧ 請參考第四章以了解更多關於排線與插座連接的相關資訊。 預先連接的系統排線 1. 4-pin BPPWR1 電源接頭(電源供應器至背板) 2. 8-pin BPPWR2 電源接頭(電源供應器至背板) 3. 8-pin VGA 電源接頭(連接至顯示卡,選配) 4. 面板連接插座(連接至前置 I/O 面板) 5. 系統風扇連接插座(主機板 FAN1-8 至系統風扇) 6. SLMPCIE3、SLMPCIE4、SLMPCIE9、SLMPCIE10 Slim PCIe 連接插座(連接至背 板) 7.
2.
GPU 機種 連接至主機板的 mini-SAS HD 插座 連接至主機板的 Slim PCIe 插座 連接至主機板的 Slim PCIe 插座 連接至 Tri-mode 擴充卡 連接至 Tri-mode 擴充卡 的 Slim PCIe 插座 的 Slim PCIe 插座 連接至主機板的 Slim PCIe 插座 連接至主機板的 Slim PCIe 插座 連接至後側硬碟槽的 miniSAS HD 插座(選配) 背板連接埠 排線 連接至 SLIMPCIE1 Slimline PCIe 至 Slimline PCIe 主機板的 SLMPCIE3 SLIMPCIE_P3 & Slimline PCIe 至 Slimline PCIe SLIMPCIE_P4 主機板的 SLMPCIE4 SLIMPCIE3 Slimline PCIe 至 Slimline PCIe 主機板的 SLMPCIE9 SLIMPCIE4 Slimline PCIe 至 Slimline PCIe 主機板的 SLMPCIE10 2-54 第二章:硬體安裝
2.9 移除系統組件 當您在安裝或移除系統裝置或是替換損壞的零組件時,或許需要移除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何移除與重新安裝下列各項系統組件。 1. 系統風扇 2. 備援式電源供應器模組 安裝/移除系統組件之前,請先關閉系統電源。 您可能需要在安裝組件前,先移除先前安裝的組件或出廠組件。 2.9.1 系統風扇 請依照以下步驟移除系統風扇: 1. 找到要更換的系統風扇。 2.
請依照以下步驟安裝系統風扇: 1. 準備相同型號與尺寸大小的新系統風扇。 2.
請依照以下的步驟安裝後側外接風扇: 1. 請使用螺絲起子撬開插槽。 若您想要安裝後側外接風扇時,請勿安裝四埠網路控制器擴充卡。 2. 準備好要安裝的後側外接風扇。 3.
4. 將後側外接風扇對齊機殼上的螺絲孔。 5.
2.9.2 備援式電源供應器模組 您可依照以下的步驟,更換損壞的備援式電源供應器模組: 1. 握住電源供應器模組上的拉把。 握把 2. 握住電源供應器上的握把,然後使用 拇指將右側的固定閂朝左推讓電源供 應器鬆脫。接著可以將此電源供應器 模組,從機殼中拉出。 握把 3.
2-60 第二章:硬體安裝
第三章: 進階安裝 本章提供本伺服器的機架安裝及使用方法。 3
3.
3.2 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1. 找到如下圖所示位於伺服器上的位置,並於兩側裝上固定閂(一邊一個,並各鎖 上二顆螺絲固定)。 螺絲孔安裝的位置可能會因您鎖使用的伺服器機型而有所不同,請參考 伺服器使用手冊上的說明。 2.
3. 使用包裝內附的螺絲將滑軌鐵件安裝至滑軌上。 4. 5. 上推彈簧鎖( ),然後將螺栓插入已選定在機架上的方形安裝孔。 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 6. (可選擇)可使用附件裡的滑軌螺絲以及滑軌墊圈( 上兩顆套上此墊圈的螺絲以進行固定。 7. 接著請重複前面的步驟 3 至 5,安裝另一側的滑軌。 ),將滑軌前後端各鎖 請確認安裝的機架滑軌(左、右)有平行一致,且安穩地固定在定位。 8.
3.3 滑軌尺寸 43.6mm 900mm 43.
3.4 理線架(僅供 1200 mm 機架滑軌選配) 您可以額外安裝理線架(CMA)來幫助收納及配置伺服器的纜線。理線架設計為可 移動式元件,方便您依機架滑軌移動伺服器而不必移動理線架。 外側連接器 內側連接器 勾環綁帶 樞軸連接器 訊號線綁帶 3.4.1 安裝理線架 請依照以下步驟安裝理線架: 1. 安裝機架滑軌。 請參考 3.1 滑軌套件 的說明安裝機架滑軌。 2.
3. 將理線器上的 3 個連接器對齊機架滑軌上的連接器。 中間滑軌連接器 樞軸連接器 內滑軌連接器(隱藏) 內側連接器 中間滑軌連接器 外側連接器 本章節的安裝步驟以左樞軸為例,右樞軸的安裝步驟極為相似。 4. 將內滑軌連接器連接至理線架 上的內側連接器。 5.
6. 將另一端的中間滑軌連接器連接至理線架上的樞軸連接器。 7.
第四章: 主機板資訊 本章提供本伺服器內建主機板的相關資訊,包括主機板 的構造圖、跳線設定及連接埠位置等。 4
4.
主機板的各項元件 跳線選擇區 頁碼 1. Clear RTC RAM (3-pin CLRTC1) 4-4 2. VGA controller setting (3-pin VGA_SW1) 4-5 3. LANNCSI setting (3-pin LANNCSI_SEL1) 4-5 4. Baseboard Management Controller setting (3-pin BMC_EN1) 4-6 5. DMLAN setting (3-pin DM_IP_SEL1) 4-6 6. IPMI SW setting (3-pin IPMI_SW1) 4-7 7. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-7 8. System select setting (3-pin SYS_SEL1) 4-8 內部指示燈 頁碼 1. Standby Power LED (SBPWR1) 4-9 2.
4.2 跳線選擇區 1.
2. VGA 控制器設定(3-pin VGA_SW1) 您可以透過本功能的設定來開啟或關閉主機板內建之 VGA 圖形顯示控制器功 能。預設值為 [1-2](開啟 VGA 功能)。 3.
4. BMC(Baseboard Management Controller)設定(3-pin BMC_EN1) 本跳線帽提供您啟用(預設)或關閉主機板內建的 BMC 控制器。 5. DMLAN 設定(3-pin DM_IP_SEL1) 本跳線帽提供您選擇 DMLAN 設定。設定為 [2-3] 以強制 DMLAN IP 使用固定 模式(IP=10.10.10.10, submask=255.255.255.
6. IPMI SW 設定(3-pin IPMI_SW1) 本跳線帽提供您選擇 GPU 感應器的通訊協定。 7.
8.
4.3 內部指示燈 1. 電力指示燈(SBPWR1) 當主機板上內建的電力指示燈(SBPWR1)亮著時,表示目前系統是處於正常 運作、省電模式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您 在置入或移除任何的硬體裝置之前,都必須先移除電源,等待警示燈熄滅才可進 行。請參考下圖所示。 2.
3.
4.4 元件與周邊裝置的連接 1. Mini-SAS HD 連接埠(ISATA1-2) 本主機板內建 mini Serial Attached SCSI(SAS)HD 連接埠,支援 Serial ATA。每個連接埠最多支援 4 個裝置。 2.
3. USB 2.0(10-1 pin U2_67) 這些插槽可用來連接 U S B 2.0 連接埠。將 U S B 擴充套件連排線連接到 USB34,然後將擴充套件安裝到機殼背部的一個空置插槽位置。這些 USB 擴充套 件排線插槽支援 USB 2.0 規格,傳輸速率高達 480 Mbps。 USB 模組為選購配備,請另行選購。 4. USB 3.2 Gen 1 連接插槽(U31G1_34; U31G1_5) 這個插槽用來連接 USB 3.2 Gen 1 模組,可在前面板或後側連接埠擴充 USB 3.2 Gen 1 模組。當您安裝 USB 3.2 Gen 1 模組,您可以享受 USB 3.2 Gen 1 的益 處,包括有更快的資料傳輸率最高達 10 Gb/s、對可充電的 USB 裝置更快的充電 速度、最佳化能源效率,以及與 USB 2.
5. 機殼開啟警示連接排針(2-pin INTRUSION1) 這組排針提供給設計有機殼開啟檢測功能的電腦主機機殼之用。此外,尚須搭 配一個外接式檢測裝置,譬如機殼開啟偵測感應器或者微型開關。在本功能啟用 時,若您有任何移動機殼元件的動作,感應器會隨即偵測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機殼開啟事件。預設設定為 CASEOPEN 與 GND 接腳短路,此功能關閉。 6.
7. 系統風扇插座(6-pin FRNT_FAN1-8; 6-pin REAR_FAN1-2) 這些插座支援連接 0.8A–1.0A(最大 12 W)或總合 6.4 A–8.
8. TPM 排線插槽(14-1 pin TPM1) 本插座支援安全性平台模組(TPM)系統,該系統可進行安全性儲存金鑰、數 位認證、密碼與資料。此外,TPM 系統也可協助增進網路安全,保護數位辨識功 能,並確保平台的整合性。 9. M.2(NGFF)插槽(NGFF1-2) 本插槽提供安裝一個 M.2 裝置。 此插槽支援 2242/2260/2280/22110 類型的 PCI-E 與 SATA 儲存裝置。 M.
10. 後側面板電源插座(4-pin BPPWR1, BPPWR4; 8-pin BPPWR2-3) 這些插座供連接後側面板的電源供應器使用。電源供應器只能以單一方向安裝 至後側面板電源插座。安裝時請確認電源供應器確實安裝且方向正確。 請勿將顯示卡連接至此插座,否則會使系統發生錯誤,並對主機板或裝 置造成永久損壞。 11.
12. VGA 排針(16-pin VGA_HDR1) 這個排針支援 VGA 高動態範圍(High Dynamic-Range)介面。 13. Micro SD 記憶卡插槽(MSD1) 主機板支援 SD 記憶卡 v2.00(SDHC) / v3.
14.
• Locator 按鈕/開關(BMCLOCBTN#) 這組排針為連接前面板 Locator 按鈕。這個按鈕按下後 Locator 指示燈將會亮 燈。 • 硬碟動作指示燈號接針(HDLED) 這組排針可連接到電腦主機面板上的硬碟動作指示燈,一旦硬碟有存取動作 時,指示燈隨即亮起。 15.
16. I2C 插槽 (10-1 pin BP_I2C1) 本插槽提供 AMD NVME 熱抽換功能與 NVME 溫度讀取功能。 17.
18. CPLD JTAG 插槽(6-pin CPLD_JTAG1) 本插槽可用以燒錄 CPLD JTAG。 19.
20.
第五章: BIOS 程式設定 本章提供伺服器之 BIOS 的升級與管理及 BIOS 設定的 相關訊息。 5
5.1 管理、更新您的 BIOS 程式 下列軟體讓您可以管理與更新主機板上的 BIOS 設定。 1. ASUS CrashFree BIOS 3 當 BIOS 程式毀損時,使用可開機的 USB 隨身碟來更新 BIOS 程式。 2. ASUS EzFlash 3. BUPDATER 使用 USB 隨身碟更新 BIOS。 使用可開機的 USB 隨身碟在 DOS 環境下更新 BIOS 程式。 上述軟體請參考相關章節的詳細使用說明。 建議您先將主機板原始的 BIOS 程式備份到可開機的 USB 隨身碟中, 以備您往後需要再度安裝原始的 BIOS 程式。使用華碩線上更新(ASUS Update)程式來拷貝主機板原始的 BIOS 程式。 5.1.
5.1.2 使用華碩 EzFlash 更新程式 華碩 EzFlash 程式讓您能輕鬆的更新 BIOS 程式,可以不必再透過開機片的冗長程 序或是到 DOS 模式下執行。 請至華碩網站 https://www.asus.com/tw/ 下載最新的 BIOS 程式檔案。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式。來到 Tools 選單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUS Tek.
5.1.3 BUPDATER 工具程式 以下的 BIOS 畫面僅供參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程式可以提供您在 DOS 環境下,使用儲存有更新的 BIOS 檔案的 USB 隨身碟來更新 BIOS 檔案。 更新 BIOS 檔案 請依照以下的步驟,使用BUPDATER 工具程式來更新 BIOS 檔案: 1. 請先造訪華碩網站(https://www.asus.com/tw/)下載最新主機板的 BIOS 檔案。並 將檔案儲存至可開機的 USB 隨身碟內。 2. 然後將華碩支援網站(support.asus.com)上的 BUPDATER 工具程式(BUPDATER. exe),下載並儲存至同一個可開機的 USB 隨身碟內。 3. 將系統開機至 DOS 環境下,然後使用鍵盤輸入指令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 USB 隨身碟裡頭的最新或原本 BIOS 檔案名 稱,然後按 鍵。 A:\>BUPDATER /i[file name].
4. 程式會進行檢查檔案,然後開始更新 BIOS 檔案。 ASUS Tek. EzFlash Utility Current Platform Platform : KMPP-D32 Version : 0215 Build date: 12/13/2020 Start Programming Flash. New Platform Platform : KMPP-D32 Version : 0217 Build date: 01/02/2021 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程式檔案時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程式會回到 DOS 畫面,請重新啟動系統,透過硬碟開機。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS720A-E11-RS12E 使用手冊 5-5
5.2 BIOS 程式設定 主機板擁有一片可編輯的韌體晶片,您可以依照 5.
5.2.1 BIOS 程式選單介紹 選單項目 設定值 功能表列 一般說明 操作功能鍵 5.2.
5.2.3 選單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 選單的項目。 點選選單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子選單 在選單畫面中,若功能選項的前面有一個小三角形標記,代表此為子選單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子選單。 5.2.5 操作功能鍵說明 在選單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動變更。 5.2.7 設定值 這些存在於選單中的設定值是提供給使用者選擇與設定之用。這些項目中,有的 功能選項僅為告知使用者目前運作狀態,並無法更改,那麼此類項目就會以淡灰色顯 示。而可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表 這是可更改的項目。 5.2.
5.3 主選單(Main) 當您進入 BIOS 設定程式時,首先出現的第一個畫面即為主選單,內容如下圖。 5.3.1 System Language [English] 設定系統使用語言。 5.3.2 System Date [Day xx/xx/xxxx] 設定您的系統日期。 5.3.
5.
Overclocking [Disabled] 啟用本項目以增進處理器時鐘。啟用本項目時,硬碟請使用外接式 PCIe 儲存裝置 控制器。設定值有:[Disabled] [Enabled] 請留意超頻設定可能會造成元件或系統損毀,並減少系統與處理器的使 用年限,進行設定前請謹慎評估風險。 Power Balancer [Disabled] 根據目前使用率動態調整所有處理器核心頻率,可提升每瓦特的效能以增進系統節 能。設定值有:[Disabled] [Auto] [Manual] 當 Power Balancer 設為 [Auto] 或 [Manual] 時,請確認已安裝最新版本的 ASUS Control Center 以支援 Power Balancer 功能。請參考以下的建議版 本: - ACC:1.4.3.
5.
5.5.1 Trusted Computing Configuration Security Device Support [Enabled] 可讓您啟動或關閉 BIOS 安全裝置支援功能。設定值有:[Disabled] [Enabled] Disable Block Sid [Disabled] 可讓您覆寫以允許 TCG 儲存裝置的 SID 驗證。設定值有:[Disable] [Enable] 5.5.2 PSP 韌體版本 本選單顯示 PSP 韌體版本。 5.5.
Power On By PCI-E/ PCI [Disabled] [Disabled] 關閉 PCIE 裝置引起的喚醒事件。 [Enabled] 啟用 PCIE 裝置引起的喚醒事件。 Power On By RTC [Disabled] [Disabled] 關閉 RTC 引起的喚醒事件。 [Enabled] 當設定為 [Eanbled] 時,RTC Alarm Date (Days) 與 Hour/Minute/ Second 選項則可以讓使用者自行設定想要的數值。 5.5.
5.5.
Parity [None] 一個 p a r i t y(同位)位元能發送資料位元來檢測一些傳輸錯誤,[M a r k] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為偶數。 [Odd] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為奇數。 [Mark] 同位位元總是 1。 [Space] 同位位元總是 0。 Stop Bits [1] Stop bits 為序列資料封包的終點(開始位元表示起始)。標準設定是 1 Stop bit。使用較慢的裝置通訊可能會需要超過 1 stop bit。設定值有:[1] [2] Flow Control [None] Flow control(流量控制)能預防在緩衝區溢滿時的資料流失。當傳送資料時, 若接收的緩衝區已經滿了,此時會送出“stop”(停止)訊號來停止傳送資料流 (data flow)。當緩衝區空出時,會再送出“start”(開始)訊號以重新開始傳 送資料流。硬體流量控制使用兩條金屬線來傳送 start/stop(開始/停止)訊號。
以下選項僅當 Consloe Redirection 項目設定為 [Enabled] 時才會顯示。 Console Redirection Settings 本項目僅當 Console Redirection 設為 [Enabled] 時才能設定。這項設定說明如 何把主電腦與遠端遙控電腦(例如使用者使用的)進行檔案交換。兩部電腦都應 具備同樣或相容的設定。 Terminal Type [ANSI] 提供您設定終端類型。 [VT100] ASCII 字元設定。 [VT100+] 延伸 VT100 支援顏色、功能鍵等等。 [VT-UTF8] 使用 UTF8 加密以映像 Unicode(萬國碼)字元在 1 或更多位元 組以上。 [ANSI] 延伸 ASCII 字元設定。 Bits per second [57600] 提供您選擇序列埠傳輸速度,這速度必須與另一邊符合,過長或過多都可能會 導致速度變慢。設定值有:[9600] [19200] [38400] [57600] [115200] Data Bits [8] 設定值有:[7] [8] Parity [None] 一個 p a r i t
Recorder Mode [Disabled] 若啟用此模式則僅會傳送文字,此為擷取終端資料。設定值有:[D i s a b l e d] [Enabled] Resolution 100x31 [Disabled] [Enabled] 本項目用來開啟或關閉延伸終端的解析度。設定值有:[Disabled] [Enabled] Putty Keypad [VT100] 本項目提供您選擇 FunctionKey 與在 Putty 上面的 Keypad。設定值有:[VT100] [LINUX] [XTERMR6] [SCO] [ESCN] [VT400] Legacy Console Redirection Settings Legacy Console Redirection Port [COM1] 可讓您選擇一個 COM 連接埠以顯示 Legacy 作業系統與 Legacy OPROM 訊息的重 新導向。設定值有:[COM1] [COM2] Resolution [80x24] 設定支援舊有作業系統的行、列數。設定值有:[80x24] [80x25] Redirection After BIOS P
5.5.
5.5.
5.5.
以下項目僅當 Device power-up delay 設定為 [Manual] 時才會顯示。 Device power-up delay in seconds [5] 本項目可以設定 device power-up delay in seconds,請使用 <+> 或 <-> 鍵調整 數值。數值的變更範圍從 1 至 40。 Mass Storage Devices 本項目提供您選擇大量儲存裝置的模擬類型。設定值有:[Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM] 5.5.
5.5.
5.5.
5.5.12 SATA 設定 本選單提供 SATA 控制器及驅動程式資訊。 5.5.
5.5.
5.
5.7 安全性選單(Security menu) 本選單可以讓您變更系統安全設定,並且提供您啟用或關閉安全開機(S e c u r e Boot)狀態與讓使用者設定系統模式(System Mode)狀態。 Administrator Password(設定系統管理員密碼) 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4.
User Password(設定使用者密碼) 請依照以下步驟設定使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟刪除使用者密碼(User Password): 1. 請選擇 Clear User Password 項目並按下 。 2.
Key Management 本項目僅當 Secure Boot Mode 設定為 [Custom] 時才會顯示,提供您修改 Secure Boot(安全開機)變量與設定 Key Management(密鑰管理)頁面。 Factory Key Provision [Disabled] 本項目可以在系統為 S e t u p M o d e 時提供您系統預設安全啟動變量。設定值 有:[Disabled] [Enabled] Restore Factory keys 本項目會安裝所有系統預設安全變量。 Reset to Setup Mode 本項目僅當您設定原廠預設金鑰時才會出現。本項目可以讓您刪除所有金鑰回 復 Setup Mode。 Export Secure Boot Variables 本項目會詢問您是否要儲存所有安全啟動變量。選擇 Y e s 以儲存,或是選擇 No 放棄。 Enroll Efi Image 本項目可以允許 Secure Boot mode 時執行 Efi Image。設定值有:[Set New] [Append] Device Guard Ready Remove‘UEFI
Key Exchange Keys (KEK) / Authorized Signatures (DB) / Forbidden Signatures (DBX) 設定值有:[Erase] [Set New] [Save to File] Authorized TimeStamps (DBT) / OsRecovery Signatures 設定值有:[Update] [Append] 華碩 RS720A-E11-RS12E 使用手冊 5-31
5.
5.
5.
5.
5.11.
以下項目僅當 Custom Pstate1 設定為 [Custom] 或 [Auto] 時才會顯示。 Custom Pstate2 [Auto] 設定值有:[Auto] [Custom] [Disabled] 以下項目僅當 Custom Pstate2 設定為 [Custom] 時才會顯示。 Pstate2 FID [5a] 指定核心頻率倍頻器。COF = 200MHz 2 FID / DID。 Pstate2 DID [c] 指定核心頻率除數。(DID[0] should zero is DID[5:0]>1Ah)。 Pstate2 VID [68] 指定核心電壓。 CCD/Core/THread Enablement 本項目可以啟用 CCD/Core/THread Enablement。 請在閱讀免責聲明後點選 I Accept。 S3 不支援 cores/threads 已被移除或關閉的系統。 以下項目僅當 CCD/Core/THread Enablement 設定為 [Accept] 時才會顯 示。 CCD Control [Auto] 設定要使用的 CCD 數量。設定此項目後,日後進行變更時需
Core Watchdog Core Watchdog Timer Enable [Auto] 本項目可以啟用或關閉 CPU Watchdog Timer。設定值有:[Disable] [Enable] [Auto] 以下項目僅當 Core Watchdog Timer Enable 設定為 [Enabled] 時才會顯 示。 Core Watchdog Timer Interval [Auto] 設定值有:[21.461s] [10.730s] [5.364s] [2.681s] [1.340s] [669.41m s] [334.05ms] [166.37ms] [82.53ms] [40.61ms] [20.970ms] [10.484ms] [5.241ms] [2.620ms] [1.309ms] [654.08us] [326.4us] [162.56us] [80.64us] [39.
5.11.
1TB remap [Auto] 設定值有:[Do not remap] [Attempt to remap] [Auto] DRAM map inversion [Auto] 設定值有:[Disabled] [Enabled] [Auto] Location of private memory regions [Auto] 設定值有:[Distributed] [Consolidated] [Auto] Disable DF to external IP SyncFloodPropagation [Auto] 設定值有:[Sync flood disabled] [Sync flood enabled] [Auto] Disable DF sync flood propagation [Auto] 設定值有:[Sync flood disabled] [Sync flood enabled] [Auto] Freeze DF module queues on error [Auto] 設定值有:[Disabled] [Enabled] [Auto] CC6 memory region encry
5.11.
Trp [Auto] 本項目可以設定列預充電時間。設定值有:[Auto] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] [10h Clk] [11h Clk] [12h Clk] [13h Clk] [14h Clk] [15h Clk] [16h Clk] [17h Clk] [18h Clk] [19h Clk] [1Ah Clk] [1Bh Clk] Tras [Auto] 本項目可以設定的行地址啟用時間。設定值有:[Auto] [15h Clk] [16h Clk] [17h Clk] [18h Clk] [19h Clk] [1Ah Clk] [1Bh Clk] [1Ch Clk] [1Dh Clk] [1Eh Clk] [1Fh Clk] [20h Clk] [21h Clk] [22h Clk] [23h Clk] [24h Clk] [25h Clk] [26h Clk] [27h Clk] [28h Clk] [29h Clk] [2Ah Clk] [2Bh Clk] [2Ch Clk]
Twr Ctrl [Auto] 本項目可以設定 Twr。設定值有:[Auto] [Manual] 以下項目僅當 Twr Ctrl 設定為 [Manual] 時才會顯示。 Twr [12] 本項目可以設定寫入恢復時間。有效數值為 51h-Ah。 Trcpage Ctrl [Auto] 本項目可以設定 Trcpage。設定值有:[Auto] [Manual] 以下項目僅當 Trcpage Ctrl 設定為 [Manual] 時才會顯示。 Trcpage [0] SDRAM 選配功能(tMAW MAC)。有效數值為 3FFh-0h。 TrdrdScL Ctrl [Auto] 本項目可以設定 TrdrdScL。設定值有:[Auto] [Manual] 以下項目僅當 TrdrdScL Ctrl 設定為 [Manual] 時才會顯示。 TrdrdScL [3] 本項目可以設定 CAS 至 CAS 延遲時間。有效數值為 Fh-1h。 TwrwrScL Ctrl [Auto] 本項目可以設定 TwrwrScL。設定值有:[Auto] [Manual] 以下項目僅當 TwrwrScL Ctrl 設定為 [Manual] 時才會
以下項目僅當 Trfc2 Ctrl 設定為 [Manual] 時才會顯示。 Trfc2 [c0] 本項目可以設定行地址重新整理週期(tRFC2)。有效數值為 3DEh-3Ch。 Trfc4 Ctrl [Auto] 本項目可以設定 Trfc4。設定值有:[Auto] [Manual] 以下項目僅當 Trfc4 Ctrl 設定為 [Manual] 時才會顯示。 Trfc4 [84] 本項目可以設定行地址重新整理週期(tRFC4)。有效數值為 3DEh-3Ch。 Tcwl [Auto] 本項目可以設定 CAS 寫入延遲。設定值有:[Auto] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Eh Clk] [10h Clk] [12h Clk] [14h Clk] Trtp [Auto] 設定值有:[Auto] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] Tcke [Auto] 設定值有:[Auto] [1 Clk] [2 Clk] [3 Clk]
TwrwrSd [Auto] 設定值有:[Auto] [1 Clk] [2 Clk] [3 Clk] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] TwrwrDd [Auto] 設定值有:[Auto] [1 Clk] [2 Clk] [3 Clk] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] TrdrdSc [Auto] 設定值有:[Auto] [1 Clk] [2 Clk] [3 Clk] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] TrdrdSd [Auto] 設定值有:[Auto] [1 Clk]
DRAM Refresh Rate [7.8 usec] 設定值有:[7.8 usec] [3.
Data Bus Configuration Data Bus Configuration User Controls [Auto] 本項目可以指定驅動強度的模式。設定值有:[Auto] [Manual] 以下項目僅當 Data Bus Configuration User Controls 設定為 [Manual] 時 才會顯示。 RttNom [Auto] 設定值有:[Rtt_Nom Disable] [RZQ/4] [RZQ/2] [RZQ/6] [RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto] RttWr [Auto] 設定值有:[Dynamic ODT Off] [RZQ/2] [RZQ/1] [Hi-Z] [RZQ/3] [Auto] RttPark [Auto] 設定值有:[Rtt_PARK Disable] [RZQ/4] [RZQ/2] [RZQ/6] [RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto] Common RAS Data Poisoning [Auto] 設定值有:[Enabled] [Disabled] [Auto] D
ECC Configuration DRAM ECC Symbol Size [Auto] 設定值有:[x4] [x8] [x16] [Auto] DRAM ECC Enable [Auto] 本項目可以啟用或關閉 DRAM ECC。設定值有:[Disabled] [Enabled] [Auto] DRAM ECC Enable [Auto] 本項目可以啟用或關閉 DRAM UECC Retry。設定值有:[Disabled] [Enabled] [Auto] Security TSME [Auto] 設定值有:[Disabled] [Enabled] [Auto] Data Scramble [Auto] 設定值有:[Disabled] [Enabled] [Auto] DRAM Memory Mapping Chipselect Interleaving [Auto] 本項目可開啟或關閉經由記憶體晶片選擇交插存取存儲區。設定值有: [Disabled] [Auto] BankGroupSwap [Auto] 設定值有:[Enabled] [Disabled] [Auto] BankGroupSwa
Memory MBIST MBIST Enable [Disabled] 本項目可以啟用或關閉 Memory MBIST。設定值有:[Enabled] [Disabled] 以下項目僅當 MBIST Enable 設定為 [Enabled] 時才會顯示。 MBIST Test Mode [Auto] 本項目可以選擇 MBIST 測試模式,可選擇 Interface Mode 或 Data Eye Mode。 設定值有:[Interface Mode] [Data Eye Mode] [Both] [Auto] MBIST Aggressors [Auto] 本項目可以啟用或關閉 M e m o r y A g g r e s s o r 測試。設定值有:[E n a b l e d] [Disabled] [Auto] MBIST Per Bit Slave Die Reporting [Auto] 設定值有:[Enabled] [Disabled] [Auto] Data Eye Pattern Select [PRBS] 設定值有:[PRBS] [SS0] [Both] Pattern Lengt
Aggressor Static Lane Select ECC [0] 設定值有:[0] – [9] Aggressor Static Lane Value [0] 設定值有:[0] – [9] Target Static Lane Control [Disabled] 設定值有:[Disabled] [Enabled] 以下項目僅當 Target Static Lane Control 設定為 [Enabled] 時才會顯示。 Target Static Lane Select Upper 32 bits [0] 設定值有:[0] – [99999999] Target Static Lane Select Lower 32 bits [0] 設定值有:[0] – [99999999] Target Static Lane Select ECC [0] 設定值有:[0] – [9] Target Static Lane Value [0] 設定值有:[0] – [9] Data Eye Type [Worst Case Margin Only] 設定值有:[1D Voltage Sweep] [1D Ti
5.11.
cTDP Control [Auto] [Auto] 使用融合 TDP。 [Manual] 設定客製化 TDP。 以下項目僅當 cTDP Control 設定為 [Manual] 時才會顯示。 cTDP [240] 本項目可以設定客製化 cTDP。 Power Package Limit Control [Manual] [Auto] 使用融合 PPT。 [Manual] 設定客製化 PPT。 以下項目僅當 Power Package Limit Control 設定為 [Manual] 時才會顯 示。 Power Package Limit [240] 本項目可以設定客製化 PPT。 APBDIS [Auto] [0] 非 APBDIS (mission mode) [1] APBDIS [Auto] 自動 DF Cstates [Auto] 設定值有:[Disabled] [Enabled] [Auto] CPPC [Auto] 設定值有:[Disabled] [Enabled] [Auto] HSMP Support [Auto] 本項目可以啟用或關閉 HSMP
以下項目僅當 Boost FmaxEn 設定為 [Manual] 時才會顯示。 Power Package Limit [0] 本項目可以設定明確加速 Fmax 頻率限制以適用所有核心(MHz)。 NBUI RAS Common Options NBIO RAS Global Control [Auto] 設定值有:[Auto] [Manual] NBIO RAS Control [Auto] 設定值有:[Disabled] [MCA] [Legacy] [Auto] Egress Poison Severity High [30011] 位元 1 表示在關聯的 IOHC Egress 埠上高嚴重程度。位元 0 表示低嚴重程度。 Egress Poison Severity Low [4] 位元 1 表示在關聯的 IOHC Egress 埠上高嚴重程度。位元 0 表示低嚴重程度。 NBIO SyncFlood Generation [Auto] 這個數值是用以遮蔽 NBIO RAS 選項造成的 SyncFlood。設定為是時,NBIO 的 SyncFlood 被遮蔽;設定為否時,NBIO 可產生
Uncorrected Converted to Poison Enable Mask Low [4] 這些設置可以啟動遮蔽內部陣列的錯誤奇偶誤差。位元設定為 1 時,與關聯 Egress 埠的陣列上 UCP 錯誤將啟動系統致命性錯誤。位元設置為 0 時,錯誤就 會遮蔽。 System Hub Watchdog Timer [a28] 此數值可以毫秒為單位設定 SYSHUB Watchdog Timer 的計時器間隔。 SLink Read Response OK [Disabled] 此數值可以設定 SLINK 讀取回應錯誤是否轉變為同意。設定為是時,讀取回應 錯誤將轉變為同意;設定為否時,將不會轉變。 SLink Read Response OK [Disabled] 此數值可以設定 SLINK 讀取回應錯誤是否轉變為同意。設定為是時,讀取回應 錯誤將轉變為同意;設定為否時,將不會轉變。設定值有:[Disabled] [Enabled] SLink Read Response Error Handling [Log Errors in MCA] 此數值可以設定 S L I N K 讀取回應錯誤是否
Enable AER Cap [Auto] 本項目可以啟用或關閉 Advanced Error Reporting Capability。設定值有:[Enable] [Disabled] [Auto Enable Rcv Err and Bad TLP Mask [Auto] 本項目可以啟用或關閉 Masking of Receiver Error and Bad TLP at Gen4 x2。設定值 有:[Enable] [Disabled] [Auto]] Early Link Speed [Auto] 本項目可以設定 Early Link Speed。設定值有:[Auto] [Gen1] [Gen2] Hot Plug Handling mode [Auto] 本項目可以設定 Hot Plug Handling mode。設定值有:[A0 Mode] [OS First (No Error Handling)] [OS First (Error Handling - Not Implemented)] [Firmware First (Not Implemented)] [Auto] Prese
NTB active on PCIeCore [Auto] 設定值有:[Auto] [Core0] [Core1] NTB Mode [Auto] 本項目可以選擇 NTB Mode (Core 0, Port 0)。設定值有:[NTB Disabled] [NTB Primary] [NTB Secondary] [NTB Random] [Auto] Link Speed [Auto] 本項目可以選擇 Link Speed for NTB Mode (Core 0, Port 0)。設定值有:[Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4] 5.12 事件記錄選單(Event Logs menu) 5.12.
Enabling/Disabling Options Smbios Event Log [Enabled] 啟用或關閉所有在開機過程中的 Smbios Event 記錄功能。設定值有:[Disabled] [Enabled] 以下項目僅當 Smbios Event Log 設定為 [Enabled] 時才會顯示。 Erasing Settings Erase Event Log [No] 本項目為提供選擇清除 Smbios Event Log 的選項,在重新啟動時清除在任何載入任 何記錄動作。設定值有:[No] [Yes, Next reset] [Yes, Every reset] Smbios Event Log Standard Settings Log System Boot Event [Disabled] 本項目可開啟或關閉記錄系統啟動事件。設定值有:[Disabled] [Enabled] MECI [1] 允許您調整 MECI 的設定值。使用 <+> 或 <-> 鍵調整數值。設定值有:[1] - [255] METW [60] 允許您調整 METW 的設定值。使用 <+> 或 <->
5.
以下項目僅當 OS Watchdog Timer 設為 [Enabled] 時才會顯示。 O/S Wtd Timer Timeout [10 minutes] 本項目提供您設定 O/S Boot Watchdog Timer(開機關門狗計時器)。設定值 有:[5 minutes] [10 minutes] [15 minutes] [20 minutes] O/S Wtd Timer Policy [Reset] 若 OS Boot Watchdog Timer 到期,則提供您設定系統應該如何回應。設定值 有:[Do Nothing] [Reset] [Power Down] System Event Log 提供您變更 SEL 事件記錄設定。 Erase SEL [No] 提供您選擇清除 SEL 的選項。設定值有:[No] [Yes, On next reset] [Yes, On every reset] 所有變更的數值需電腦重新開機會才會生效。 View FRU Information 按下 鍵以檢視 FRU 資訊。 欄位裡無 FRU 資訊時表示需由 O.E.
Router IP Address 本項目可以設定路由器 IP 位址。 Router MAC Address 本項目可以設定路由器 MAC 位址。 Configure IPV6 support DM_LAN1/Shared LAN IPV6 Support [Enabled] 本項目可以啟用或關閉 LAN1 IPV6 支援。設定值有:[Disabled] [Enabled] 以下項目僅當 IPV6 Support 設為 [Enabled] 時才會顯示。 Configuration Address source [Previous State] 選擇設定的網路通道的參數為靜態或動態(透過 BIOS 或 BMC)。未指定選項 將不會修改在 BIOS 裡的任何 BMC 網路參數。設定值有:[Previous State] [Static] [DynamicBmcDhcp] 以下項目僅當 Configuration Address source 設為 [Static] 時才會顯示。 Station IPV6 address 本項目可以設定站台 IPV6 位址。 Prefix Length 本項目可以設定前置
安裝驅動程式 本章提供主機板相關之驅動程式的安裝說明。 6
6.1 安裝應用程式與工具程式 驅動及公用程式光碟裡提供您主機板相關的驅動程式、管理應用程式與工具程式, 可以讓您將主機板功能最佳化。 驅動及公用程式 DVD 光碟裡的內容如有變更,恕不另行通知。請造訪華 碩網站(https://www.asus.com/tw/)以更新最新的軟體與工具程式。 在驅動及公用程式 DVD 光碟的主選單裡有以下幾個標籤頁: 1. Drivers - 驅動程式主選單提供了您目前需要安裝的一些硬體驅動程式。 2. Utilities - 工具軟體選單顯示了可安裝於此系統的應用軟體與工具。 3. Manual - 使用手冊選單提供您使用手冊的開啟連結。 您需要在作業系統中使用網路瀏覽器軟體才能開啟使用手冊。 4.
附錄 在本附錄裡將列出相關的聯絡資訊。
KMPP-D32 架構圖
服務與支援 請造訪 https://www.asus.