Podręcznik użytkownika RT-AC88U Dwupasmowy gigabitowy router bezprzewodowy AC 3100
PL10302 Wydanie pierwsze Maj 2015 Copyright © 2015 ASUSTeK COMPUTER INC. Wszelkie prawa zastrzeżone. Żadnej z części tego podręcznika, włącznie z opisem produktów i oprogramowania, nie można powielać, przenosić, przetwarzać, przechowywać w systemie odzyskiwania danych lub tłumaczyć na inne języki, w jakiejkolwiek formie lub w jakikolwiek sposób, za wyjątkiem wykonywania kopii zapasowej dokumentacji otrzymanej od dostawcy, bez wyraźnego, pisemnego pozwolenia ASUSTeK COMPUTER INC. (“ASUS”).
Spis treści 1 1.1 1.2 1.3 1.4 1.5 1.6 Poznanie routera bezprzewodowego Witamy!.............................................................................................7 Zawartość opakowania...............................................................7 Router bezprzewodow................................................................8 Usytuowanie routera................................................................ 10 Wymagania dotyczące instalacji..........................................
Spis treści 3.4.2 QoS..............................................................................................38 3.4.3 Historia stron sieci Web........................................................39 3.4.4 Monitor ruchu.........................................................................40 3.5 Używanie aplikacji USB............................................................ 41 3.5.1 Korzystanie z funkcji AiDisk................................................41 3.5.
Spis treści 4.3.5 DMZ (Strefa DMZ)..................................................................78 4.3.6 DDNS (Usługa DDNS)............................................................79 4.3.7 NAT Passthrough (Przekazywanie NAT).........................80 4.4 4.5 4.6 IPv6 (Protokół IPv6)................................................................... 81 Serwer sieci VPN......................................................................... 82 Zapora.................................................
6.1 6.2 Rozwiązywanie problemów Rozwiązywanie podstawowych problemów.................106 Często zadawane pytania (FAQ) ........................................108 Załączniki Ogłoszenie.................................................................................................116 Informacje kontaktowe producenta................................................
1 Poznanie routera bezprzewodowego 1.1 Witamy! Dziękujemy za zakup routera bezprzewodowego RT-AC88U firmy ASUS! RT-AC88U charakteryzuje się podwójnym pasmem 2.4GHz oraz 5GHz zapewniając jednoczesne bezprzewodowe przesyłanie strumieni HD; serwer SMB; serwer UPnP AV i serwer FTP do wymiany plików 24 godz/7 dni w tygodniu; możliwość obsługi 300.000 sesji. Technologia ASUS Green Network Technology zapewnia do 70% oszczędności energii. 1.
1.3 Router bezprzewodow WPS WiFi Gniazda USB 3.0 Gniazda te służą do podłączania urządzeń USB 3.0 takich jak dyski twarde USB lub pamięci flash USB. Dioda zasilania Wyłączona: Brak zasilania Włączona: Urządzenie jest gotowe. Powolne miganie: Tryb ratunkowy 2.4GHz LED / 5GHz LED Wyłączona: Brak sygnału 2.4 GHz / 5 GHz. Włączona: System bezprzewodowy jest gotowy. M iganie: Przesyłanie lub odbieranie danych przez połączenie bezprzewodowe.
Przycisk włączenia/wyłączenia wskaźnika LED funkcji WPS Naciśnij ten przycisk, aby włączyć/wyłączyć wskaźnik LED funkcji WPS na panelu. Przycisk Wł./Wył. WI-FI Naciśnij ten przycisk, aby włączyć/wyłączyć połączenie Wi-Fi. Przycisk RESET Przycisk służy do przywracania domyślnych ustawień systemu. Przycisk WPS Przycisk służy do uruchamiania kreatora WPS. Gniazda USB 2.0 Gniazda te służą do podłączania urządzeń USB 2.0 takich jak dyski twarde USB lub pamięci flash USB.
1.4 Usytuowanie routera Dla zapewnienia najlepszej transmisji sygnału bezprzewodowego pomiędzy routerem bezprzewodowym a podłączonymi urządzeniami sieciowymi należy upewnić się, że: • Router bezprzewodowy należy umieścić centralnie, aby zapewnić maksymalny zasięg transmisji bezprzewodowej do urządzeń sieciowych w pomieszczeniu bądź w budynku. • Urządzenie trzymać z dala od metalowych przeszkód oraz bezpośredniego działania promieniowania słonecznego.
1.5 Wymagania dotyczące instalacji Do wykonania ustawień sieci potrzeba jednego lub dwóch komputerów, które spełniają następujące wymagania systemowe: • Port Ethernet RJ-45 (LAN) (10Base-T/100BaseTX/1000BaseTX) • Obsługa sieci bezprzewodowej IEEE 802.
1.6 Instalacja routera WAŻNE! • Router bezprzewodowy należy zainstalować za pomocą połączenia przewodowego, aby uniknąć możliwych problemów z instalacją. • Przed skonfigurowaniem routera bezprzewodowego ASUS wykonać następujące czynności: • W przypadku zastępowania istniejącego routera odłączyć router od sieci. • Odłączyć kable/przewody od istniejącego modemu. Jeżeli modem ma baterię zasilania awaryjnego należy ją również wyciągnąć. • Ponownie uruchomić komputer (zalecane). 1.6.
2. Używając dołączonego kabla sieciowego, podłączyć komputer do gniazda sieci lokalnej routera bezprzewodowego. WAŻNE! Upewnij się, czy dioda sieci lokalnej miga. 3 Używając drugiego kabla sieciowego, podłączyć modem do gniazda sieci WAN routera bezprzewodowego. 4. Włożyć wtyczkę zasilacza prądu przemiennego modemu do gniazda wejścia prądu stałego i włożyć zasilacz do gniazda sieciowego. 1.6.
3. Włożyć wtyczkę zasilacza prądu przemiennego modemu do gniazda wejścia prądu stałego i włożyć zasilacz do gniazda sieciowego. 4. Zainstalować w komputerze bezprzewodową kartę sieciową IEEE 802.11a/b/g/n/ac. Uwagi: • Szczegółowe informacje dotyczące połączenia z siecią bezprzewodową znajdują się w podręczniku użytkownika adaptera WLAN.
2 Ustawienia sprzętu 2.1 Logowanie do GUI web Router bezprzewodowy ASUS jest dostarczany z intuicyjnym GUI (graphics user interface (graficzny interfejs użytkownika)), który umożliwia łatwą konfigurację jego różnych funkcji poprzez przeglądarkę sieci web, taką jak Internet Explorer, Firefox, Safari lub Google Chrome. UWAGA: Funkcje mogą się różnić w zależności od wersji oprogramowania sprzętowego. Aby zalogować się do GUI web: 1.
2.2 QIS z autodetekcją Quick Internet Setup (Szybkie ustawienia połączenia z Internetem) Funkcja QIS (Quick Internet Setup (Szybkie ustawienia połączenia z Internetem)) pomaga w szybkim wykonaniu połączenia z Internetem. Uwagi: Podczas ustawiania połączenia z Internetem pierwszy raz, naciśnij i przytrzymaj przycisk Reset na routerze bezprzewodowym w celu przywrócenia jego ustawień fabrycznych. Aby użyć QIS z autodetekcją: 1. Zaloguj się do sieciowego interfejsu graficznego.
2. Router bezprzewodowy automatycznie wykryje, czy typ połączenia ISP to Dynamic IP (Dynamiczny adres IP), PPPoE, PPTP, L2TP oraz Static IP (Statyczny adres IP). Wprowadź niezbędne informacje dla typu połączenia ISP. WAŻNE! Uzyskaj niezbędne informacje dotyczące połączenia z Internetem od ISP.
Uwagi: • Automatyczne wykrywanie typu połączenia ISP jest wykonywane przy pierwszej konfiguracji routera bezprzewodowego lub po zresetowaniu routera bezprzewodowego do ustawień domyślnych. • Jeżeli funkcja QIS nie może wykryć typu połączenia z Internetem, kliknij polecenie Skip to manual setting (Przejdź do ustawień ręcznych) (patrz zrzut ekranu w etapie 1) i ręcznie skonfiguruj ustawienia połączenia. 3. Przydziel nazwę sieci (SSID) i klucz zabezpieczenia dla połączenia bezprzewodowego 2,4GHz i 5 GHz.
2.3 Łączenie z siecią bezprzewodową Po skonfigurowaniu routera bezprzewodowego za pomocą funkcji QIS można połączyć komputer lub inne urządzenia inteligentne z siecią bezprzewodową. W celu połączenia z siecią: 1. Kliknij ikonę sieci w obszarze powiadomień komputera, aby wyświetlić dostępne sieci bezprzewodowe. 2. Wybierz sieć bezprzewodową do połączenia, a następnie kliknij przycisk Connect (Połącz). 3.
3 Konfiguracja ustawień ogólnych 3.1 Korzystanie z pozycji Network Map (Mapa sieci) Pozycja Network Map (Mapa sieci) umożliwia konfigurowanie ustawień zabezpieczeń sieci, zarządzanie klientami sieciowymi oraz monitorowanie urządzenia USB.
3.1.1 Wykonanie ustawień zabezpieczenia sieci bezprzewodowej Aby zabezpieczyć sieć bezprzewodową przed nieautoryzownym dostępem należy skonfigurować ustawienia zabezpieczenia. W celu wykonania ustawień zabezpieczenia sieci bezprzewodowej: 1. W panelu nawigacji przejdź do pozycji General (Ogólne) > Network Map (Mapa sieci). 2.
Ustawienia zabezpieczenia 5GHz-2 3. W polu Wireless name (SSID) (Nazwa sieci bezprzewodowej (SSID)), wprowadź unikalną nazwę dla własnej sieci bezprzewodowej. 4. Na liście rozwijanej Authentication Method (Metoda uwierzytelniania) wybierz metodę uwierzytelniania dla sieci bezprzewodowej. W przypadku wybrania metody uwierzytelniania WPA-Personal lub WPA-2 Personal wprowadź klucz WPA-PSK lub hasło zabezpieczeń. WAŻNE! Standard IEEE 802.
3.1.2 Zarządzanie klientami sieci W celu zarządzania klientami sieci: 1. W panelu nawigacji przejdź do pozycji General (Ogólne) > wybierz zakładkę Network Map (Mapa sieci). 2. Na ekranie Network Map (Mapa sieci), wybierz ikonę Client Status (Stan klienta), aby wyświetlić informacje o klientach sieciowych. 3. Aby zablokować dostęp klienta do sieci, wybierz klienta i kliknij pozycję block (zablokuj).
3.1.3 Monitorowanie urządzenia USB Router bezprzewodowy firmy ASUS jest wyposażony w dwa porty USB, do których można podłączyć urządzenia USB lub drukarkę USB w celu udostępnienia plików i drukarki klientom w sieci. Uwaga: 24 • Do używania tej funkcji wymagane jest podłączenie do portu USB 3.0/2.0 na panelu tylnym posiadanego routera bezprzewodowego urządzenia pamięci masowej USB takiego jak dysk twardy USB lub napęd flash USB.
WAŻNE! Aby inni klienci sieciowi mogli uzyskiwać dostęp do urządzenia USB za pomocą witryny FTP/narzędzia klienta FTP innej firmy, funkcji Servers Center (Centrum serwerów), usługi Samba lub aplikacji AiCloud, należy najpierw utworzyć konto udostępniania i skonfigurować uprawnienia/prawa dostępu. Dalsze szczegółowe informacje znajdują się w części 3.5. Używanie aplikacji USB i 3.6 Korzystanie z aplikacji AiCloud w niniejszym podręczniku użytkownika. Aby monitorować urządzenie USB: 1.
Bezpieczne usuwanie dysku USB WAŻNE: Nieprawidłowe usunięcie dysku USB może spowodować uszkodzenie danych. Aby bezpiecznie usunąć dysk USB: 1. W panelu nawigacji przejdź do pozycji General (Ogólne) > Network Map (Mapa sieci). 2. W prawym górnym rogu ekranu kliknij pozycję > Eject USB disk (Wysuń dysk USB). Po pomyślnym wysunięciu dysku USB jego stan zostanie zmieniony na Unmounted (Odłączony).
3.2 Tworzenie Guest Network (Sieć gości) Pozycja Guest Network (Sieć gości) udostępnia tymczasowym użytkownikom możliwość połączenia z Internetem za pomocą oddzielnych identyfikatorów SSID lub sieci, bez zapewniania dostępu do sieci prywatnej. UWAGA: Router RT-AC88U obsługuje maksymalnie sześć identyfikatorów SSID (trzy identyfikatory SSID 2,4 GHz i trzy 5 GHz). W celu utworzenia sieci gości: 1. W panelu nawigacji przejdź do pozycji General (Ogólne) > Guest Network (Sieć gości). 2.
4. Aby zmienić ustawienia gości, kliknij ustawienia gości, które chcesz zmodyfikować. Kliknij przycisk Remove (Usuń), aby usunąć ustawienia gości. 5. Przypisz do sieci tymczasowej nazwę sieci bezprzewodowej w polu Network Name (SSID) [Nazwa sieci (SSID)]. 6. Wybierz ustawienie dla pozycji Authentication Method (Metoda uwierzytelniania). 7. W przypadku wybrania metody uwierzytelniania WPA wybierz szyfrowanie WPA. 8.
3.3 AiProtection Funkcja AiProtection zapewnia monitorowanie w czasie rzeczywistym, które umożliwia wykrywanie złośliwego oprogramowania, programów szpiegujących oraz niechcianego dostępu. Filtruje ona także niechciane witryny i aplikacje, a także umożliwia ustalenie harmonogramu dostępu do Internetu przez połączone urządzenie.
3.3.1 Network Protection Funkcja Network Protection (Ochrona sieci) zapobiega wykorzystywaniu luk w sieci oraz zabezpiecza przed niechcianym dostępem do sieci. Konfiguracja funkcji Network Protection (Ochrona sieci) Aby skonfigurować funkcję Network Protection (Ochrona sieci): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection. 2. Na stronie głównej AiProtection kliknij kartę Network Protection (Ochrona sieci). 3.
WAŻNE! Stan pozycji z oznaczeniem Yes (Tak) na stronie Router Security Assessment (Ocena zabezpieczeń routera) uważa się za bezpieczny. W przypadku pozycji z oznaczeniem No (Nie), Weak (Słabe) lub Very Weak (Bardzo słabe) zalecana jest odpowiednia konfiguracja. 4. (Opcjonalnie) Na stronie Router Security Assessment (Ocena zabezpieczeń routera) skonfiguruj ręcznie pozycje z oznaczeniem No (Nie), Weak (Słabe) lub Very Weak (Bardzo słabe). Aby to zrobić: a. Kliknij pozycję.
Blokowanie niebezpiecznych witryn Funkcja ta ogranicza dostęp do niebezpiecznych witryn określonych w bazie danych w chmurze w celu zapewnienia zawsze aktualnej ochrony. UWAGA: Funkcja ta jest uaktywniana automatycznie w przypadku uruchomienia skanowania Router Weakness Scan (Skanowanie słabych punktów routera). Aby włączyć funkcję Malicious Sites Blocking (Blokowanie niebezpiecznych witryn): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection. 2.
Wykrywanie i blokowanie zainfekowanych urządzeń Funkcja ta zapobiega przesyłaniu informacji osobistych lub zainfekowanego stanu przez zainfekowane urządzenia do urządzeń zewnętrznych. UWAGA: Funkcja ta jest uaktywniana automatycznie w przypadku uruchomienia skanowania Router Weakness Scan (Skanowanie słabych punktów routera). Aby włączyć funkcję Vulnerability protection (Ochrona przed wykorzystywaniem luk): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection. 2.
3.3.2 Konfiguracja funkcji Parental Controls (Kontrola rodzicielska) Kontrola rodzicielska zapewnia kontrolę nad czasem dostępu do Internetu oraz umożliwia ustawienie ograniczenia czasu używania sieci klienta. Aby przejść na stronę główną funkcji Parental Controls (Kontrola rodzicielska): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection. 2. Na stronie głównej AiProtection kliknij kartę Parental Controls (Kontrola rodzicielska).
Filtry sieci Web i aplikacji Web & Apps Filters (Filtry sieci Web i aplikacji) to funkcja pozycji Parental Controls (Kontrola rodzicielska), która umożliwia blokowanie dostępu do niechcianych witryn lub aplikacji. Aby skonfigurować funkcję Web & Apps Filters (Filtry sieci Web i aplikacji): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection. 2.
Ustalanie harmonogramu Funkcja Time Scheduling (Ustalanie harmonogramu) umożliwia ustawienie ograniczenia czasu używania sieci klienta. UWAGA: Należy upewnić się, że czas systemowy jest zsynchronizowany z serwerem NTP. Aby skonfigurować funkcję Time Scheduling (Ustalanie harmonogramu): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > AiProtection > Parental Controls (Kontrola rodzicielska) > Time Scheduling (Ustalanie harmonogramu). 2.
3. W kolumnie Clients Name (Nazwa klienta) wprowadź lub wybierz z listy rozwijanej nazwę klienta. UWAGA: Można także wprowadzić adres MAC klienta w kolumnie Client MAC Address (Adres MAC klienta). Nazwa klienta nie może zawierać znaków specjalnych ani spacji, ponieważ mogłyby one spowodować nieprawidłowe działanie routera. 4. Kliknij ikonę w celu dodania profilu klienta. 5. Kliknij przycisk Apply (Zastosuj), aby zapisać ustawienia.
3.4 Adaptacyjna funkcja QoS 3.4.1 Monitor przepustowości Funkcja ta umożliwia monitorowanie przepustowości sieci WAN/LAN oraz zapewnia informacje o szybkości przesyłania i pobierania. Analiza aplikacji Aby włączyć funkcję Apps analysis (Analiza aplikacji): Na karcie Bandwidth Monitor (Monitor przepustowości) przejdź do panelu Apps Analysis (Analiza aplikacji) i kliknij pozycję ON (WŁ.).
3.4.2 QoS Funkcja ta zapewnia przepustowość dla priorytetowych zadań i aplikacji. Aby włączyć funkcję QoS: 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > Adaptive QoS (Adaptacyjna funkcja QoS) > karta QoS. 2. W panelu Enable Smart QoS (Włącz inteligentną funkcję QoS) kliknij pozycję ON (WŁ.). 3. Wypełnij pola przepustowości przesyłania i pobierania. UWAGA: Uzyskaj informacje dotyczące pasma od ISP. Można także przejść do witryny http://speedtest.
3.4.3 Historia stron sieci Web Funkcja ta umożliwia wyświetlenie historii i szczegółowych informacji o odwiedzanych przez klienta stronach internetowych lub adresach URL. Aby wyświetlić pozycję Web History (Historia stron sieci Web): 1. W panelu nawigacji przejdź kolejno do pozycji General (Ogólne) > Adaptive QoS (Adaptacyjna funkcja QoS) > karta Web History (Historia stron sieci Web). 2. (Opcjonalnie) Kliknij przycisk Refresh (Odśwież), aby wyczyścić listę.
3.4.4 Monitor ruchu Funkcja monitorowania ruchu zapewnia informacje dotyczące przepustowości i szybkości połączenia z Internetem, siecią przewodową lub bezprzewodową. Umożliwia ona monitorowanie ruchu sieciowego w czasie rzeczywistym lub na poziomie każdego dnia. Zapewnia ponadto opcję wyświetlania informacji o ruchu sieciowym z ostatnich 24 godzin. Aby skonfigurować funkcję Traffic Monitor (Monitor ruchu): 1.
3.5 Używanie aplikacji USB Funkcja USB Extension (Rozszerzenie USB) udostępnia podmenu AiDisk, Servers Center (Centrum serwerów), Network Printer Server (Serwer wydruków sieciowych) i Download Master (Zarządzanie pobieraniem). WAŻNE! Aby móc korzystać z funkcji serwera, należy podłączyć urządzenie pamięci USB, takie jak dysk twardy USB lub pamięć flash USB, do portu USB 2.0 na panelu tylnym routera bezprzewodowego. Urządzenie pamięci USB powinno zostać odpowiednio sformatowane i podzielone na partycje.
3. Wybierz prawa dostępu, które chcesz przydzielić użytkownikom mającym dostęp do współdzielonych danych. 4. Utwórz nazwę domeny przez usługi DDNS ASUS, wybierz I will use the service and accept the Terms of service (Będę korzystał z tej usługi i akceptuję warunki korzystania z usługi) i wprowadź nazwę domeny. Po zakończeniu kliknij Next (Dalej).
3.5.2 Korzystanie z funkcji Servers Center (Centrum serwerów) Funkcja Servers Center (Centrum serwerów) umożliwia udostępnianie plików multimedialnych z dysku USB poprzez katalog Media Server (Serwer multimediów), usługę udostępniania Samba lub FTP. Za pomocą funkcji Servers Center (Centrum serwerów) można także skonfigurować inne ustawienia dysku USB.
W celu wyświetlenia, przejdź kolejno do pozycji General (Ogólne) > USB application (Aplikacja USB) > Media Services and Servers (Usługi i serwery multimedialne) > karta Media Servers (Serwery multimediów). Należy zapoznać się z poniższymi opisami pól: • Włączyć serwer iTunes?: Wybierz pozycję ON/OFF (WŁ./ WYŁ.) w celu włączenia/wyłączenia serwera iTunes. • Włącz serwer multimediów DLNA: Wybierz pozycję ON/ OFF (WŁ./WYŁ.) w celu włączenia/wyłączenia serwera multimediów DLNA.
2. Wykonaj poniższe czynności, aby dodać, usunąć lub zmodyfikować konto. W celu utworzenia nowego konta: a) Kliknij ikonę , aby dodać nowe konto. b) W polach Account (Konto) i Password (Hasło) wpisz nazwę i hasło klienta sieciowego. Wprowadź ponownie hasło w celu potwierdzenia. Kliknij przycisk Add (Dodaj) w celu dodania konta do listy. W celu usunięcia istniejącego konta: a) Wybierz konto, które chcesz usunąć. b) Kliknij ikonę .
3. Z listy plików/folderów wybierz typ praw dostępu, który ma zostać przydzielony określonym plików/folderów: • R/W: Wybierz tę opcję, aby przypisać dostęp do zapisu/ odczytu. • R: Wybierz tę opcję, aby przypisać dostęp tylko do odczytu. • Nie: Wybierz tę opcję, aby nie udostępniać określonego foldera. 4. Kliknij Apply (Zastosuj), aby zastosować zmiany.
W celu korzystania z usługi udostępniania FTP: UWAGI: Upewnij się, że serwer FTP został skonfigurowany za pomocą funkcji AiDisk. Szczegółowe informacje znajdują się w rozdziale 3.5.1 Korzystanie z funkcji AiDisk. 1. W panelu nawigacji kliknij pozycję General (Ogólne) > USB application (Aplikacja USB) > Media Services and Servers (Usługi i serwery multimedialne) > wybierz zakładkę FTP Share (Udostępnianie FTP). 2.
3.5.3 Sieć 3G/4G Do routera RT-AC88U można podłączyć modemy USB 3G/4G w celu zapewnienia dostępu do Internetu. UWAGA: Listę zweryfikowanych modemów USB można znaleźć na stronie: http://event.asus.com/2009/networks/3gsupport/ W celu skonfigurowania dostępu do Internetu 3G/4G: 1. W panelu nawigacji kliknij pozycję General (Ogólne) > USB application (Aplikacja USB) > 3G/4G. 2. W polu Enable USB Modem (Włącz modem USB) zaznacz pozycję Yes (Tak). 3.
3.6 Korzystanie z aplikacji AiCloud 2.0 AiCloud 2.0 to aplikacja usługi w chmurze umożliwiająca zapisywanie, synchronizowanie, udostępnianie i uzyskiwanie dostępu do plików. W celu korzystania z aplikacji AiCloud: 1. Pobierz aplikację ASUS AiCloud ze sklepu Google Play lub Apple Store i zainstaluj ją na urządzeniu inteligentnym. 2. Połącz urządzenie inteligentne z siecią. Wykonaj instrukcje, aby ukończyć proces konfiguracji aplikacji AiCloud.
3.6.1 Funkcja Cloud Disk (Dysk w chmurze) W celu utworzenia dysku w chmurze: 1. Podłącz urządzenie pamięci USB do routera bezprzewodowego. 2. Włącz funkcję Cloud Disk (Dysk w chmurze). 3. P rzejdź do witryny https://router.asus.com i wprowadź konto logowania i hasło routera. W celu zapewnienia lepszego działania zalecane jest używanie przeglądarki Google Chrome lub Firefox.
4. M ożna już uzyskiwać dostęp do plików dostępnych w ramach funkcji Cloud Disk (Dysk w chmurze) za pomocą urządzeń połączonych z siecią. UWAGA: Uzyskanie dostępu do urządzeń połączonych z siecią wymaga ręcznego wprowadzenia nazwy użytkownika i hasła danego urządzenia, które ze względów bezpieczeństwa nie zostaną zapisane przez aplikację AiCloud.
3.6.2 Funkcja Smart Access (Dostęp inteligentny) Funkcja Smart Access (Dostęp inteligentny) ułatwia uzyskiwanie dostępu do sieci domowej za pomocą nazwy domeny routera. UWAGI: • Nazwę domeny routera można utworzyć za pomocą usługi ASUS DDNS. Szczegółowe informacje zawiera rozdział 4.3.5 DDNS (Usługa DDNS). • Aplikacja AiCloud zapewnia domyślnie zabezpieczone połączenie HTTPS.
3.6.3 Funkcja Smart Sync (Synchronizacja inteligentna) W celu korzystania z funkcji Smart Sync (Synchronizacja inteligentna): 1. Uruchom aplikację AiCloud, kliknij pozycję Smart Sync (Synchronizacja inteligentna) > Go (Idź). 2. Wybierz pozycję ON (WŁ.) w celu włączenia funkcji Smart Sync (Synchronizacja inteligentna). 3. Kliknij przycisk Add new account (Dodaj nowe konto). 4. Wprowadź hasło konta w usłudze ASUS WebStorage i wybierz katalog, który chcesz zsynchronizować z usługą WebStorage. 5.
4 Konfiguracja ustawień zaawansowanych 4.1 Wireless (Sieć bezprzewodowa) 4.1.1 General (Ogólne) Zakładka General (Ogólne) umożliwia konfigurację podstawowych ustawień sieci bezprzewodowej. W celu skonfigurowania podstawowych ustawień sieci bezprzewodowej: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Wireless (Sieć bezprzewodowa) > wybierz zakładkę General (Ogólne). 2. Wybierz pasmo częstotliwości sieci bezprzewodowej 2,4 GHz lub 5 GHz. 3.
4. Przypisz unikatową nazwę identyfikatora SSID (Service Set Identifier) lub sieci zawierającą maksymalnie 32 znaki w celu identyfikacji sieci bezprzewodowej. Urządzenia Wi-Fi będą identyfikować sieć bezprzewodową i łączyć się z nią za pomocą przypisanego identyfikatora SSID. Identyfikatory SSID widoczne na pasku informacyjnym są aktualizowane po zapisaniu nowych identyfikatorów SSID w ustawieniach. UWAGA: Unikatowe identyfikatory SSID można przypisać dla pasma częstotliwości 2,4 GHz lub 5 GHz. 5.
4.1.2 WPS WPS (Wi-Fi Protected Setup) to standard zabezpieczeń sieci bezprzewodowej, który ułatwia łączenie urządzeń z siecią bezprzewodową. Funkcję WPS można skonfigurować za pomocą kodu PIN lub przycisku WPS. UWAGA: Należy upewnić się, że urządzenia obsługują funkcję WPS. W celu włączenia funkcji WPS w sieci bezprzewodowej: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Wireless (Sieć bezprzewodowa) > wybierz zakładkę WPS. 2.
Uwaga: Funkcja WPS obsługuje uwierzytelnianie za pomocą metody Open System (Otwarty system), WPA-Personal i WPA2-Personal. Funkcja WPS nie obsługuje sieci bezprzewodowych korzystających z metody szyfrowania Shared Key (Klucz wspólny), WPA-Enterprise, WPA2Enterprise ani RADIUS. 3. W polu WPS Method (Metoda WPS) wybierz opcję Push Button (Przycisk polecenia) lub Client PIN Code (Kod PIN klienta). Po wybraniu opcji Push Button (Przycisk polecenia) przejdź do kroku 4.
4.1.3 Bridge (Mostek) Dzięki funkcji Bridge (Mostek) lub WDS (Wireless Distribution System) router bezprzewodowy firmy ASUS może łączyć się z innym bezprzewodowym punktem dostępowym w trybie wyłączności, przy jednoczesnym braku dostępu innych urządzeń lub stacji bezprzewodowych do routera bezprzewodowego firmy ASUS. Można to także traktować jako repeater bezprzewodowy, za pomocą którego router bezprzewodowy firmy ASUS komunikuje się z innym punktem dostępowym lub urządzeniem bezprzewodowym.
• HYBRID (HYBRYDOWY): Włączenie funkcji mostka bezprzewodowego z możliwością łączenia się innych urządzeń/stacji bezprzewodowych z routerem. UWAGA: W trybie Hybrid (Hybrydowy) urządzenia bezprzewodowe połączone z routerem bezprzewodowym firmy ASUS będą miały zapewnioną tylko połowę szybkości połączenia punktu dostępowego. 4.
4.1.4 Wireless MAC Filter (Filtr adresów MAC urządzeń bezprzewodowych) Pozycja Wireless MAC Filter (Filtr adresów MAC urządzeń bezprzewodowych) zapewnia kontrolę nad pakietami przesyłanymi na określony adres MAC (Media Access Control) w danej sieci bezprzewodowej. W celu skonfigurowania filtra adresów MAC urządzeń bezprzewodowych: 1.
4.1.5 RADIUS Setting (Ustawienia serwera RADIUS) Pozycja RADIUS (Remote Authentication Dial In User Service) Setting (Ustawienia serwera RADIUS) zapewnia dodatkową warstwę zabezpieczeń w przypadku wybrania metody uwierzytelniania WPA-Enterprise, WPA2-Enterprise lub Radius with 802.1x (Radius z 802.1x). W celu skonfigurowania ustawień serwera RADIUS w sieci bezprzewodowej: 1. Upewnij się, że wybrana metoda uwierzytelniania routera bezprzewodowego to WPA-Enterprise, WPA2-Enterprise lub Radius with 802.
4.1.6 Professional (Profesjonalne) Na ekranie Professional (Profesjonalne) dostępne są opcje konfiguracji zaawansowanej. UWAGA: Zalecane jest zachowanie wartości domyślnych tego ekranu. Na ekranie Professional Settings (Ustawienia profesjonalne) można skonfigurować następujące pozycje: • Częstotliwość: Wybierz pasmo częstotliwości dla pozycji, dla których zastosowanie mają ustawienia profesjonalne. • Włącz łączność radiową: Wybierz opcję Yes (Tak), aby włączyć sieć bezprzewodową.
• Data włączania łączności radiowej (weekend): Można określić, w które dni weekendu sieć bezprzewodowa ma być włączona. • Pora dnia, w której łączność radiowa ma być włączona: Można określić przedział czasu, w którym sieć bezprzewodowa ma być włączona podczas weekendu. • Ustawiaj izolowany punkt dostępowy: Pozycja Set AP isolated (Ustawiaj izolowany punkt dostępowy) uniemożliwia wzajemną komunikację urządzeń bezprzewodowych połączonych z daną siecią.
• Włącz tryb WMM APSD: Pozycja Enable WMM APSD (WiFi Multimedia Automatic Power Save Delivery) (Włącz tryb WMM APSD) usprawnia zarządzanie energią urządzeń bezprzewodowych. Wybierz opcję Disable (Wyłącz), aby wyłączyć tryb WMM APSD. • Regulacja mocy TX: Za pomocą pozycji TX Power adjustment (Regulacja mocy TX) określana jest wartość miliwatów (mW) konieczna do zasilania wyjścia sygnału radiowego routera bezprzewodowego. Wprowadź wartość z zakresu od 0 do 100.
4.2.2 DHCP Server (Serwer DHCP) Router bezprzewodowy korzysta z serwera DHCP do automatycznego przypisywania adresów IP w sieci. Można określić zakres adresów IP oraz czas dzierżawy dla klientów w sieci. W celu wykonania ustawień serwera DHCP: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > LAN (Sieć LAN) > wybierz zakładkę DHCP Server (Serwer DHCP). 2. W polu Enable the DHCP Server? (Włączyć serwer DHCP?) zaznacz Yes (Tak). 3.
5. W polu IP Pool Ending Address (Adres końcowy zakresu IP) wprowadź adres końcowy IP. 6. W polu Lease Time (Czas dzierżawy) wprowadź czas zakończenia ważności adresów IP, po czym router bezprzewodowy automatycznie przydzieli nowe adresy IP klientom sieci. UWAGI: • Podczas określania zakresu adresów IP zalecane jest stosowanie formatu adresów IP: 192.168.1.xxx (xxx może być dowolną liczbą pomiędzy 2 a 254).
4.2.3 Route (Trasa) Jeśli dana sieć korzysta z więcej niż jednego routera bezprzewodowego, można skonfigurować tabelę routingu w celu współdzielenia tej samej usługi internetowej. UWAGA: Jeśli użytkownik nie posiada specjalistycznej wiedzy na temat tabel routingu, zalecane jest pozostawienie domyślnych ustawień trasy. W celu skonfigurowania tabeli routingu sieci LAN: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > LAN (Sieć LAN) > wybierz zakładkę Route (Trasa). 2.
4.2.4 IPTV Router bezprzewodowy obsługuje połączenia z usługami IPTV udostępniane przez usługodawcę internetowego lub sieć LAN. Zakładka IPTV zawiera ustawienia konieczne do konfiguracji pozycji IPTV, VoIP, multiemisji i UDP dla danej usługi. W celu uzyskania konkretnych informacji dotyczących usługi należy skontaktować się z usługodawcą internetowym.
4.3 WAN (Sieć WAN) 4.3.1 Internet Connection (Połączenie internetowe) Na ekranie Internet Connection (Połączenie internetowe) można skonfigurować ustawienia różnego typu połączeń WAN. W celu skonfigurowania ustawień połączenia WAN: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > WAN (Sieć WAN) > wybierz zakładkę Internet Connection (Połączenie internetowe). 2. Skonfiguruj poniższe ustawienia. Po zakończeniu kliknij przycisk Apply (Zastosuj).
• Włącz NAT: Translator adresów sieciowych NAT (Network Address Translation) to system, w którym jeden publiczny adres IP (adres IP sieci WAN) jest używany do zapewniania dostępu do Internetu klientom sieciowym o prywatnym adresie IP w sieci LAN. Prywatny adres IP każdego klienta sieciowego jest zapisywany w tabeli NAT i używany do rozsyłania przychodzących pakietów danych.
• Adres MAC: Pozycja MAC (Media Access Control) address (Adres MAC) to unikatowy identyfikator urządzenia sieciowego. Niektórzy usługodawcy internetowi monitorują adresy MAC urządzeń sieciowych, które łączą się z ich usługą i odrzucają wszelkie próby połączeń urządzeń nierozpoznanych. Aby uniknąć problemów z połączeniami spowodowanych niezarejestrowanym adresem MAC, można: • Skontaktować się z usługodawcą internetowym i zaktualizować adres MAC skojarzony z jego usługą.
4.3.2 Dwie sieci WAN Router bezprzewodowy firmy ASUS zapewnia obsługę dwóch sieci WAN. Dla funkcji dwóch sieci WAN można ustawić dowolny z poniższych dwóch trybów: • Failover Mode (Tryb pracy awaryjnej): Wybierz ten tryb w celu używania dodatkowej sieci WAN jako awaryjnego dostępu do sieci.
4.3.3 Port Trigger (Wyzwalanie portów) Wyzwalanie zakresu portu otwiera wstępnie określony port przychodzący na ograniczony czas za każdym razem, gdy klient w sieci lokalnej nawiązuje połączenie wychodzące z określonym portem. Wyzwalanie portów jest używane w następujących przypadkach: • Więcej niż jeden klient lokalny wymaga przekierowania portu dla tej samej aplikacji, ale w innym czasie. • Aplikacja wymaga określonych portów przychodzących innych niż porty wychodzące.
4. W tabeli Trigger Port List (Lista portów wyzwalania) wprowadź następujące informacje: • Opis: Wprowadź krótką nazwę lub opis usługi. • Port wyzwalania: Określ port wyzwalający otwarcie portu przychodzącego. • Protokół: Wybierz protokół TCP lub UDP. • Port przychodzący: Określ port przychodzący do odbierania danych przychodzących z Internetu. • Protokół: Wybierz protokół TCP lub UDP. 5. Kliknij przycisk Add (Dodaj) w celu dodania do listy informacji o wyzwalaniu portów.
4.3.4 Virtual Server/Port Forwarding (Serwer wirtualny/ Przekierowanie portów) Przekierowanie portów to metoda kierowania ruchu sieciowego z Internetu przychodzącego na określony port lub zakres portów do urządzenia lub urządzeń w sieci lokalnej. Po skonfigurowaniu funkcji Port Forwarding (Przekierowanie portów) routera komputery spoza sieci będą mogły uzyskiwać dostęp do określonych usług zapewnianych przez komputer w sieci.
3. W polu Famous Server List (Lista znanych serwerów) wybierz typ usługi, do której chcesz uzyskać dostęp. 4. W polu Famous Game List (Lista znanych gier) wybierz popularną grę, do której chcesz uzyskać dostęp. Pozycja ta zawiera informacje o porcie wymaganym do prawidłowego działania wybranej popularnej gry online. 5. W tabeli Port Forwarding List (Lista przekierowania portów) wprowadź następujące informacje: • Nazwa usługi: Wprowadź nazwę usługi.
• Local Port (Port lokalny): Wprowadź określony port do odbierania przekierowanych pakietów. Pozostaw to pole puste, jeśli chcesz, aby pakiety przychodzące były przekierowywane na określony zakres portu. • Protocol (Protokół): Wybierz protokół. W przypadku braku pewności wybierz opcję BOTH (OBA). 5. Kliknij przycisk Add (Dodaj) w celu dodania do listy informacji o wyzwalaniu portów. Kliknij przycisk Delete (Usuń) w celu usunięcia z listy wpisu dotyczącego wyzwalania portów. 6.
4.3.5 DMZ (Strefa DMZ) W wirtualnej strefie DMZ dostęp do Internetu ma jeden klient, który odbiera wszystkie pakiety przychodzące do danej sieci lokalnej. Ruch przychodzący z Internetu jest zwykle odrzucany i kierowany do określonego klienta tylko wtedy, gdy w danej sieci skonfigurowane zostało przekierowanie portów lub wyzwalanie portów. W przypadku konfiguracji strefy DMZ tylko jeden klient sieciowy odbiera wszystkie pakiety przychodzące.
4.3.6 DDNS (Usługa DDNS) Skonfigurowanie usługi DDNS (Dynamic DNS) umożliwia uzyskiwanie dostępu do routera spoza sieci za pomocą usługi ASUS DDNS lub innej usługi DDNS. W celu skonfigurowania usługi DDNS: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > WAN (Sieć WAN) > wybierz zakładkę DDNS (Usługa DDNS). 2. Skonfiguruj poniższe ustawienia. Po zakończeniu kliknij przycisk Apply (Zastosuj).
• Włącz symbole wieloznaczne: Włącz obsługę symboli wieloznacznych, jeśli jest to wymagane przez usługę DDNS. UWAGI: Usługa DDNS nie będzie działać w poniższych przypadkach: • Router bezprzewodowy korzysta z prywatnego adresu IP sieci WAN (192.168.x.x, 10.x.x.x lub 172.16.x.x), na co wskazuje tekst w kolorze żółtym. • Router może być w sieci, która korzysta z wielu tabel NAT. 4.3.
4.4 IPv6 (Protokół IPv6) Niniejszy router bezprzewodowy obsługuje adresowanie IPv6, system obsługujący więcej adresów IP. Standard ten nie jest jeszcze powszechnie dostępny. W celu sprawdzenia, czy dana usługa internetowa obsługuje protokół IPv6 należy skontaktować się z usługodawcą internetowym. W celu skonfigurowania protokołu IPv6: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > IPv6 (Protokół IPv6). 2. Wybierz opcję dla pozycji Connection Type (Typ połączenia).
4.5 Serwer sieci VPN Wirtualna sieć prywatna VPN (Virtual Private Network) zapewnia bezpieczną komunikację z komputerem zdalnym lub siecią zdalną przy użyciu sieci publicznej, np. Internetu. UWAGA: Do skonfigurowania połączenia sieci VPN konieczny jest adres IP lub nazwa domeny serwera sieci VPN, do którego dostęp ma zostać uzyskany. W celu skonfigurowania dostępu do serwera sieci VPN: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > VPN Server (Serwer sieci VPN). 2.
4.6 Zapora Router bezprzewodowy może pełnić funkcję zapory sprzętowej w sieci. UWAGA: Funkcja Firewall (Zapora) jest domyślnie włączona. 4.6.1 Ogólne W celu skonfigurowania podstawowych ustawień pozycji Firewall (Zapora): 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Firewall (Zapora) > wybierz zakładkę General (Ogólne). 2. W polu Enable Firewall (Włącz zaporę) zaznacz pozycję Yes (Tak). 3.
W celu skonfigurowania filtra adresów URL: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Firewall (Zapora) > wybierz zakładkę URL Filter (Filtr adresów URL). 2. W polu Enable URL Filter (Włącz filtr adresów URL) wybierz pozycję Enabled (Włączono). 3. Wprowadź adres URL i kliknij przycisk . 4. Kliknij przycisk Apply (Zastosuj). 4.6.3 Filtr słów kluczowych Filtr słów kluczowych blokuje dostęp do stron sieci Web zawierających określone słowa kluczowe.
3. Wprowadź słowo lub wyrażenie i kliknij przycisk Add (Dodaj). 4. Kliknij przycisk Apply (Zastosuj). UWAGI: • Pozycja Keyword Filter (Filtr słów kluczowych) zależy od zapytania DNS. Jeśli klient sieciowy uzyskał już dostęp do witryny sieci Web, np. http://www.abcxxx.com, witryna ta nie zostanie zablokowana (odwiedzone wcześniej witryny sieci Web są zapisywane w pamięci podręcznej DNS).
W celu skonfigurowania filtra usług sieciowych: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Firewall (Zapora) > wybierz zakładkę Network Service Filter (Filtr usług sieciowych). 2. W polu Enable Network Services Filter (Włącz filtr usług sieciowych) zaznacz pozycję Yes (Tak). 3. Wybierz opcję dla pozycji Filter table type (Typ tabeli filtrów). Pozycja Black List (Czarna lista) umożliwia blokowanie określonych usług sieciowych.
4.7 Administration (Administracja) 4.7.1 Operation Mode (Tryb działania) Na stronie Operation Mode (Tryb działania) można wybrać odpowiedni tryb sieci. W celu skonfigurowania trybu działania: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Administration (Administracja) > wybierz zakładkę Operation Mode (Tryb działania). 2.
3. Kliknij przycisk Apply (Zastosuj). UWAGA: Po zmianie trybu nastąpi ponowne uruchomienie routera. 4.7.2 System Na stronie System można skonfigurować ustawienia routera bezprzewodowego. W celu skonfigurowania ustawień System: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Administration (Administracja) > wybierz zakładkę System. 2.
• Zezwalaj tylko na określone adresy IP: Kliknij pozycję Yes (Tak), jeśli chcesz określić adresy IP urządzeń, które mogą uzyskiwać dostęp do ustawień interfejsu graficznego routera bezprzewodowego z sieci WAN. • Lista klientów: Wprowadź adresy IP sieci WAN urządzeń sieciowych, które mogą uzyskiwać dostęp do ustawień routera bezprzewodowego. Lista ta będzie miała zastosowanie po wybraniu opcji Yes (Tak) w pozycji Only allow specific IP (Zezwalaj tylko na określone adresy IP). 3.
4.7.4 Przywracanie/zapisywanie/przesyłanie ustawień Aby przywrócić/zapisać/przesłać ustawienia: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Administration (Administracja) > wybierz zakładkę Restore/Save/Upload Setting (Przywróć/Zapisz/Załaduj ustawienia). 2. Wybierz zadanie: • Aby przywrócić domyślne ustawienia fabryczne, kliknij Restore (Przywróć) i kliknij OK w komunikacie potwierdzenia.
4.8 System Log (Dziennik systemu) W pozycji System Log (Dziennik systemu) znajduje się lista zarejestrowanych aktywności w sieci. UWAGA: Po ponownym uruchomieniu lub wyłączeniu routera dziennik systemu jest resetowany. W celu wyświetlenia dziennika systemu: 1. W panelu nawigacji przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > System Log (Dziennik systemu). 2.
5 Narzędziowych Uwagi: • Pobierz i zainstaluj programy narzędziowe routera bezprzewodowego z witryny firmy ASUS: • Device Discovery wer. 1.4.7.1 — http://dlcdnet.asus.com/pub/ ASUS/LiveUpdate/Release/Wireless/Discovery.zip • FFirmware Restoration wer. 1.9.0.4 — http://dlcdnet.asus.com/ pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip • Windows Printer Utility wer. 1.0.5.5 — http://dlcdnet.asus.com/ pub/ASUS/LiveUpdate/Release/Wireless/Printer.
5.2 Firmware Restoration Narzędzie Firmware Restoration (Odtwarzanie oprogramowania) wykorzystywane jest w routerze bezprzewodowym ASUS w przypadku niepowodzenia procesu aktualizacji oprogramowania. Umożliwia ono wczytanie określonego oprogramowania. Proces trwa około trzech do czterech minut. WAŻNE! : Przed skorzystaniem z narzędzia Firmware Restoration (Odtwarzanie oprogramowania) uruchomić tryb ratunkowy. UWAGA: Funkcja ta nie jest obsługiwana w systemie MAC OS.
3. Ustaw statyczny adres IP komputera i wprowadź poniższe wartości w celu skonfigurowania ustawień protokołu TCP/IP: Adres IP: 192.168.1.x Maska podsieci: 255.255.255.0 4. Na pulpicie komputera kliknąć Start (Start)> All Programs (Wszystkie programy) > ASUS Utility RT-AC88U Wireless Router (Narzędzie routera bezprzewodowego ASUS RT-AC88U) > Firmware Restoration (Odtwarzanie oprogramowania sprzętowego). 5. Wybrać plik oprogramowania, a następnie kliknąć przycisk Upload (Prześlij).
UWAGA: Funkcja serwera wydruku jest obsługiwana w systemie Windows® XP, Windows® Vista i Windows® 7. W celu skonfigurowania trybu udostępniania drukarki EZ: 1. W panelu nawigacji przejdź do pozycji General (Ogólne) > USB Application (Aplikacja USB) > Network Printer Server (Sieciowy serwer wydruku). 2. Kliknij pozycję Download Now! (Pobierz teraz!), aby pobrać program narzędziowy drukarki sieciowej.
4. Wykonaj instrukcje ekranowe w celu przeprowadzenia ustawień sprzętu, a następnie kliknij Next (Dalej). 5. Zaczekaj kilka minut na zakończenie początkowych ustawień. Kliknij Next (Dalej). 6. Kliknij Finish (Zakończ) w celu dokończenia instalacji.
7. Wykonaj instrukcje systemu operacyjnego Windows® w celu instalacji sterownika drukarki. 8. Po zakończeniu instalacji sterownika drukarki klienci sieciowi będą mogli korzystać z drukarki.
5.3.2 Udostępnianie drukarki za pomocą protokołu LPR Za pomocą protokołu LPR/LPD (Line Printer Remote/Line Printer Daemon) drukarkę można udostępnić komputerom z systemem operacyjnym Windows® i MAC. Udostępnianie drukarki LPR W celu udostępnienia drukarki LPR: 1. Na pulpicie systemu Windows® kliknij kolejno pozycje Start > Devices and Printers (Urządzenia i drukarki) > Add a printer (Dodaj drukarkę) w celu uruchomienia pozycji Add Printer Wizard (Kreator dodawania drukarki). 2.
3. Zaznacz pozycję Create a new port (Utwórz nowy port), a następnie ustaw dla pozycji Type of Port (Typ portu) opcję Standard TCP/IP Port (Standardowy port TCP/IP). Kliknij przycisk New Port (Nowy port). 4. W polu Hostname or IP address (Nazwa hosta drukarki lub adres IP) wprowadź adres IP routera bezprzewodowego, a następnie kliknij przycisk Next (Dalej).
5. Zaznacz pozycję Custom (Niestandardowy), a następnie kliknij przycisk Settings (Ustawienia). 6. Ustaw dla pozycji Protocol (Protokół) opcję LPR. W polu Queue Name (Nazwa kolejki) wprowadź wartość LPRServer (Serwer LPR), a następnie kliknij przycisk OK, aby kontynuować.
7. Kliknij przycisk Next (Dalej), aby zakończyć konfigurację standardowego portu TCP/IP. 8. Zainstaluj sterownik drukarki podany na liście dostawców. Jeśli danej drukarki nie ma na liście, kliknij przycisk Have Disk (Z dysku), aby ręcznie zainstalować sterowniki drukarki z dysku CD-ROM lub pliku.
9. Kliknij przycisk Next (Dalej), aby zaakceptować domyślną nazwę drukarki. 10. Kliknij przycisk Finish (Zakończ), aby zakończyć instalację.
5.4 Program Download Master Download Master to program narzędziowy umożliwiający pobieranie plików nawet wtedy, gdy laptop lub inne urządzenia są wyłączone. UWAGA: Aby móc korzystać z programu Download Master, do routera bezprzewodowego należy podłączyć urządzenie USB. W celu korzystania z programu Download Master: 1. Kliknij kolejno pozycje General (Ogólne) > USB application (Aplikacja USB) > Download Master, aby automatycznie pobrać i zainstalować program narzędziowy.
5. Skonfiguruj ustawienia zaawansowane za pomocą panelu nawigacji. 5.4.1 Konfigurowanie ustawień pobierania BitTorrent W celu skonfigurowania ustawień pobierania BitTorrent: 1. W panelu nawigacji programu Download Master kliknij pozycję Bit Torrent (Pobieranie BitTorrent), aby wyświetlić stronę Bit Torrent Setting (Ustawienia pobierania BitTorrent). 2. Wybierz określony port dla zadania pobierania. 3.
5.4.2 Ustawienia pobierania NZB Można skonfigurować serwer USENET w celu pobierania plików NZB. Po wprowadzeniu ustawień serwera USENET kliknij przycisk Apply (Zastosuj).
6 Rozwiązywanie problemów 6.1 Rozwiązywanie podstawowych problemów W rozdziale tym omówiono rozwiązania problemów, które mogą wystąpić podczas korzystania z routera. W przypadku pojawienia się problemów, których nie opisano w tym rozdziale, należy przejść do witryny pomocy technicznej firmy ASUS dostępnej pod adresem: http://support.asus.com/ w celu uzyskania dalszych informacji o produkcie oraz szczegółowych danych kontaktowych działu pomocy technicznej firmy ASUS.
Sprawdź, czy kable Ethernet są prawidłowo podłączone. • Jeśli kabel Ethernet łączący router z modemem jest podłączony w prawidłowy sposób, świecić się będzie dioda LED sieci WAN. • Jeśli kabel Ethernet łączący uruchomiony komputer z routerem jest podłączony w prawidłowy sposób, świecić się będzie odpowiednia dioda LED sieci LAN. Sprawdź, czy ustawienia sieci bezprzewodowej komputera są zgodne z ustawieniami routera.
6.2 Często zadawane pytania (FAQ) Nie mogę uzyskać dostępu do interfejsu graficznego routera przy użyciu przeglądarki sieci Web • Jeśli komputer jest podłączony w sposób przewodowy, sprawdź połączenie kabla Ethernet i stan diody LED zgodnie z opisem w poprzedniej części. • Upewnij się, że używane dane logowania są prawidłowe. Domyślna fabryczna nazwa logowania i hasło to „admin/ admin”. Upewnij się, że podczas wprowadzania danych logowania klawisz Caps Lock jest wyłączony.
Klient nie może ustanowić połączenia bezprzewodowego z routerem. UWAGA: W przypadku wystąpienia problemów z nawiązaniem połączenia z siecią 5 Ghz należy sprawdzić, czy urządzenie sieciowe obsługuje częstotliwość 5 Ghz i czy jest wyposażone w funkcje podwójnego pasma. • Poza zakresem: • Przesuń router bliżej klienta bezprzewodowego. • Ustaw anteny routera w najlepszym położeniu zgodnie z opisem w części 1.4 Ustawianie pozycji routera. • Wyłączono serwer DHCP: 1. Uruchom sieciowy interfejs graficzny.
• Ukryto identyfikator SSID. Jeśli urządzenie wyszukuje identyfikatory SSID innych routerów, ale nie może znaleźć identyfikatora SSID posiadanego routera, przejdź do pozycji Advanced Settings (Ustawienia zaawansowane) > Wireless (Sieć bezprzewodowa) > General (Ogólne), zaznacz opcję No (Nie) dla pozycji Hide SSID (Ukryj SSID) i zaznacz opcję Auto (Automat.) dla pozycji Control Channel (Kanał kontrolny).
Niedostępny Internet. • Sprawdź, czy router może nawiązać połączenie z adresem IP sieci WAN usługodawcy internetowego. Aby to zrobić, uruchom sieciowy interfejs graficzny, przejdź do pozycji General (Ogólne) > Network Map (Mapa sieci) i sprawdź pozycję Internet Status (Stan połączenia z Internetem).
• Przywróć ustawienia domyślne routera. Uruchom sieciowy interfejs graficzny, przejdź do pozycji Administration (Administracja) > Restore/Save/Upload Setting (Przywróć/ Zapisz/Załaduj ustawienia) i kliknij przycisk Restore (Przywróć). Domyślne konto logowania i hasło to „admin”. Jak przywrócić domyślne ustawienia systemu? • Przejdź do pozycji Administration (Administracja) > Restore/ Save/Upload Setting (Przywróć/Zapisz/Załaduj ustawienia) i kliknij przycisk Restore (Przywróć).
Nie można uzyskać dostępu do sieciowego interfejsu graficznego Przed konfiguracją routera bezprzewodowego wykonać czynności opisane w tej części dla komputera hosta i klientów sieciowych. A. Wyłączyć serwer proxy jeżeli jest włączony Windows® 7 1. Kliknij przycisk Start > Internet Explorer w celu uruchomienia przeglądarki internetowej. 2. Kliknij przycisk Tools (Narzędzia) > Internet options (Opcje internetowe) > zakładkę Connections (Połączenia) > LAN settings (Ustawienia sieci LAN). 3.
MAC OS 1. W przeglądarce Safari kliknąć Safari > Preferences (Preferencje) > Advanced (Zaawansowane) > Change Settings... (Zmień ustawienia...) 2. Na ekranie Network (Sieć) usunąć zaznaczenie FTP Proxy (Proxy FTP) i Web Proxy (HTTP) (Proxy www (HTTP)). 3. Po zakończeniu kliknąć przycisk Apply Now (Zastosuj teraz). Uwaga: Szczegółowe informacje dotyczące wyłączania serwera proxy, patrz funkcja pomocy danej przeglądarki. B. Skonfigurować ustawienia TCP/IP do automatycznego uzyskiwania adresu IP.
3. W celu automatycznego uzyskania ustawień iPv4 IP, zaznacz opcję Obtain an IP address automatically (Automatycznie uzyskaj adres IP). W celu automatycznego uzyskania ustawień iPv6 IP, zaznacz opcję Obtain an IPv6 address automatically (Automatycznie uzyskaj adres IPv6). 4. Po zakończeniu kliknij przycisk OK. MAC OS 1. Kliknij ikonę Apple located on the top left of your screen. umieszczoną w górnej lewej części ekranu. 2.
C. Wyłączyć połączenie dial-up jeżeli jest włączone. Windows® 7 1. Kliknij przycisk Start > Internet Explorer w celu uruchomienia przeglądarki internetowej. 2. Kliknij przycisk Tools (Narzędzia) > Internet options (Opcje internetowe) > zakładkę Connections (Połączenia). 3. Zaznaczyć opcję Never dial a connection (Nigdy nie wybieraj połączenia). 4. Po zakończeniu kliknij przycisk OK. Uwaga: Szczegółowe informacje o wyłączaniu połączenia dial-up, patrz funkcja pomocy przeglądarki sieciowej.
Załączniki Ogłoszenie ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus. com/english/Takeback.htm for the detailed recycling information in different regions.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Prohibition of Co-location This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Safety Information To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 25 cm between the radiator and your body. Use on the supplied antenna.
This equipment may be operated in AT, BE, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IE, IT, LU, MT, NL, PL, PT, SK, SL, ES, SE, GB, IS, LI, NO, CH, BG, RO, RT. Canada, Industry Canada (IC) Notices This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
WARNING! 122 • This radio transmitter (3568A-RTGW00) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
NCC 警語 經型式認證合格之低功率射頻電機,非經許可,公司、商號或 使用者均不得擅自變更頻率、加大功率或變更原設計之特性及 功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通 信;經發現有干擾現象時,應立即停用,並改善至無干擾時方 得繼續使用。前項合法通信,指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電 波輻射性電機設備之干擾。 GNU General Public License Licensing information This product includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please see The GNU General Public License for the exact terms and conditions of this license.
Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price.
the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. Terms & conditions for copying, distribution, & modification 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
does not bring the other work under the scope of this License. 3.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
For Turkey only Authorised distributors in Turkey: BOGAZICI BIL GISAYAR SAN. VE TIC. A.S. Tel. No.: +90 212 3311000 Address: AYAZAGA MAH. KEMERBURGAZ CAD. NO.10 AYAZAGA/ISTANBUL CIZGI Elektronik San. Tic. Ltd. Sti. Tel. No.: +90 212 3567070 Address: CEMAL SURURI CD. HALIM MERIC IS MERKEZI No: 15/C D:5-6 34394 MECIDIYEKOY/ ISTANBUL KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S. Tel. No.: +90 216 5288888 Address: EMEK MAH.ORDU CAD. NO:18, SARIGAZi, SANCAKTEPE ISTANBUL AEEE Yönetmeliğine Uygundur.
Informacje kontaktowe producenta ASUSTeK COMPUTER INC. (Asia Pacific) Adres 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 Strona internetowa www.asus.com.tw Pomoc techniczna Telefon Faks Wsparcie online +886228943447 +886228907698 support.asus.com ASUS COMPUTER INTERNATIONAL (Ameryka) Adres Telefon Faks Strona internetowa Strona internetowa 800 Corporate Way, Fremont, CA 94539, USA +15107393777 +15106084555 usa.asus.com support.asus.
Informacje o globalnych punktach wsparcia technicznego dla sieci Region Country Service Hours 09:00-13:00 ; 14:00-18:00 Mon-Fri 09:00-18:00 Mon-Fri Cyprus 800-92491 France Hungary 0033-170949400 0049-1805010920 0049-1805010923 ( component support ) 0049-2102959911 ( Fax ) 0036-15054561 Italy 199-400089 Greece 00800-44142044 Austria Netherlands/ Luxembourg Belgium Norway Sweden Finland Denmark Poland Spain Portugal Slovak Republic Czech Republic Switzerland-German Switzerland-French Switzerland-I
Informacje o globalnych punktach wsparcia technicznego dla sieci Region Country Australia New Zealand Japan Korea Thailand Asia-Pacific Singapore Malaysia Philippine India India(WL/NW) Indonesia Americas Hotline Numbers 1300-278788 0800-278788 0800-1232787 0081-473905630 ( Non-Toll Free ) 0082-215666868 0066-24011717 1800-8525201 0065-64157917 0065-67203835 ( Repair Status Only ) 0060-320535077 1800-18550163 1800-2090365 0062-2129495000 500128 (Local Only) Vietnam 1900-555581 Hong Kong USA Canada
Informacje o globalnych punktach wsparcia technicznego dla sieci Region Middle East + Africa Country Egypt Saudi Arabia UAE Turkey South Africa Israel Romania Bosnia Herzegovina Bulgaria Balkan Countries Croatia Montenegro Serbia Slovenia Estonia Latvia Lithuania-Kaunas Lithuania-Vilnius Hotline Numbers 800-2787349 800-1212787 00971-42958941 0090-2165243000 0861-278772 *6557/00972-39142800 *9770/00972-35598555 0040-213301786 Service Hours 09:00-18:00 Sun-Thu 09:00-18:00 Sat-Wed 09:00-18:00 Sun-Thu 09:0