Motherboard SABERTOOTH X99 用戶手冊
ii
C10096 1.00 版 2015 年 3 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License (“GPL”) and under the Lesser General Public License Version (“LGPL”). The GPL and LGPL licensed code in this product is distributed without any warranty. Copies of these licenses are included in this product.
五年質保 全國聯保 華碩產品質量保證卡 請用剪刀沿虛線剪下 尊敬的華碩產品用戶: 首先非常感謝您選用華碩公司產品,讓我們有機會向您提供優質的服務。為了使我們的服務讓 您更滿意,在購買後請您認真閱讀此說明並妥善保存此質量保證卡。 保修說明注意事項: 一、 請將此質量保證卡下方的用戶資料填寫完整,並由最終直接經銷商加蓋印章,如果沒有加蓋 印章,請找原購買處補蓋以保障您的權益。請務必保留購買發票或複印件,否則華碩公司將 以產品的出廠日期為參照進行保修。 二、 華碩公司對在中國大陸地區(不包括港澳台地區)發售的、經合法渠道銷售給消費者的華碩 特種部隊主板產品實行三年的免費保修服務。 三、 華碩公司對在中國大陸地區(不包括港澳台地區)發售的、經合法渠道銷售給消費者的華碩 主板及顯卡產品實行全國聯保服務。注: A. 消費者必須出具正規購買發票或國家認可的有效憑證方可享受全國聯保。 B. 如消費者無法出具正規購買發票或國家認可的有效憑證,則需送修至原購買經銷商 處享受保修服務。 四、 若經本公司判斷屬下列因素,則不屬於免費保修服務的範圍,本公司將有權利收取維修費 用: A.
vi
目錄內容 華碩產品質量保證卡................................................................................................................... v 安全性須知.....................................................................................................................................x 電氣方面的安全性............................................................................................................x 操作方面的安全性............................................................................................................
目錄內容 2.3 主板後側與音頻連接端口..........................................................................................2-12 2.3.1 後側面板連接端口.........................................................................................2-12 2.3.2 音頻輸出/輸入連接圖標說明....................................................................2-14 2.4 第一次啟動電腦.............................................................................................................2-16 2.5 關閉電源................................................................
目錄內容 第四章:軟件支持 4.1 安裝操作系統.................................................................................................................... 4-1 4.2 驅動程序及應用程序 DVD 光盤信息...................................................................... 4-1 4.2.1 運行驅動程序及應用程序 DVD 光盤....................................................... 4-1 4.2.2 取得軟件用戶手冊........................................................................................... 4-3 4.3 軟件信息....................................................................
安全性須知 電氣方面的安全性 • 為避免可能的電擊造成嚴重損害,在搬動電腦主機之前,請先將電腦電源線暫時 從電源插槽中拔掉。 • 當您要加入硬件設備到系統中時,請務必先連接該設備的數據線,然後再連接電 源線。可能的話,在安裝硬件設備之前先拔掉電腦的電源電源線。 • 當您要從主板連接或拔除任何的數據線之前,請確定所有的電源線已事先拔掉。 • 在使用擴展卡或擴展卡之前,我們建議您可以先尋求專業人士的協助。這些設備 有可能會干擾接地的迴路。 • 請確定電源的電壓設置已調整到本國/本區域所使用的電壓標準值。若您不確定您 所屬區域的供應電壓值為何,請就近詢問當地的電力公司人員。 • 如果電源已損壞,請不要嘗試自行修復。請將之交給專業技術服務人員或經銷商 來處理。 操作方面的安全性 • 在您安裝主板以及加入硬件設備之前,請務必詳加閱讀本手冊所提供的相關信 息。 • 在使用產品之前,請確定所有的排線、電源線都已正確地連接好。若您發現有任 何重大的瑕疵,請儘速聯絡您的經銷商。 • 為避免發生電氣短路情形,請務必將所有沒用到的螺絲、回形針及其他零件收 好,不要遺留在主板上或電腦主機中。 • 灰塵、濕氣以及劇烈的溫度變化都會影
關於這本用戶手冊 產品用戶手冊包含了所有當您在安裝華碩 SABERTOOTH X99 主板時所需用到的 信息。 用戶手冊的編排方式 用戶手冊是由下面幾個章節所組成: • 第一章:產品介紹 您可以在本章節中發現諸多華碩所賦予本主板的優異特色。利用簡潔易懂的說 明讓您能很快地掌握本主板的各項特性,當然,在本章節中我們也會提及所有能 夠應用在本主板的新產品技術。 • 第二章:硬件設備信息 本章節描述所有您在安裝系統元件時必須完成的硬件安裝程序。詳細內容有: 處理器與內存安裝、跳線選擇區設置以及主板的各種設備接口。 • 第三章:BIOS 程序設置 本章節描述如何使用 BIOS 設置程序中的每一個菜單項目來更改系統的配置設 置。此外也會詳加介紹 BIOS 各項設置值的使用時機與參數設置。 • 第四章:軟件支持 您可以在本章節中找到所有包含在華碩驅動程序及應用程序光盤中的軟件相關 信息。 • 第五章:RAID 支持 本章節介紹 RAID 的各項設置。 xi
提示符號 為了能夠確保您正確地完成主板設置,請務必注意下面這些會在本手冊中出現的標 示符號所代表的特殊含意。 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到電腦主板元件。 要:此符號表示您必須要遵照手冊所描述之方式完成一項或多項軟硬件 重 的安裝或設置。 注意:提供有助於完成某項工作的訣竅和其他額外的信息。 哪裡可以找到更多的產品信息 您可以通過下面所提供的兩個渠道來獲得您所使用的華碩產品信息以及軟硬件的升 級信息等。 1. 華碩網站 您可以到 http://www.asus.com.cn 華碩電腦互聯網站取得所有關於華碩軟硬件產 品的各項信息。 2.
電子電氣產品有害物質限制使用標識要求:圖中之數字為產品之環保 使用期限。僅指電子電氣產品中含有的有害物質不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 有害物質的名稱及含量說明標示: 有害物質 部件名稱 鉛(Pb) 汞(Hg) 鎘(Cd) 六價鉻 (Cr(VI)) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 印刷電路板及其電 子組件 × ○ ○ ○ ○ ○ 外部信號連接口及 線材 × ○ ○ ○ ○ ○ 本表格依據 SJ/T 11364 的規定編制。 ○: 表示該有害物質在該部件所有均質材料中的含量均在 GB/T 26572 規定的限量 要求以下。 ×: 表示該有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 規定 的限量要求,然該部件仍符合歐盟指令 2011/65/EU 的規范。 備註:此產品所標示的環保使用期限,系指在一般正常使用狀況下。 xiii
SABERTOOTH X99 規格列表 中央處理器 支持採用 LGA2011-v3 規格插槽的 Intel® Core™ i7 處理器 支持 22nm 處理器 支持 Intel® Turbo Boost 2.0 技術* * 對 Intel® Turbo Boost 2.0 技術的支持依照處理器的類型而不同 ** 請訪問 www.asus.com.cn 取得最新的 Intel 處理器支持列表 芯片組 Intel® X99 Express 芯片組 內存 8 x 使用符合 non-ECC unbuffered DDR4 2400/2133 MHz 內存,最高可以擴展至 64GB 內存 支持四通道內存架構 支持 Intel® Extreme Memory Profile(XMP)技術 * 擴展槽 對高速內存的支持會受到特定處理器之物理特性的影響,請訪問 www.asus.com.cn 或參考用戶手冊取得最新的內存合格供應商支 持列表(QVL) 40-LANE CPU 3 x PCI Express 3.0/2.
SABERTOOTH X99 規格列表 存儲設備連接槽 全新 Intel® Core i7 處理器: - 1 x M.2 x4 插槽 3 擁有支持 M k e y、2242/2260 /2280/22110 類型存儲設備(僅支持 PCIe SSD) Intel® X99 Express 芯片組支持 RAID 0、1、5、10 與 Intel® Rapid Storage 技術 13: - 1 x S A T A E x p r e s s 連接端口(灰色,兼容於 2 x SATA 6.0 Gb/s 連接端口) - 8 x SATA 6.
SABERTOOTH X99 規格列表 獨家 TUF 功能 “Ultimate COOL!”散熱設計 - TUF Thermal Armor - TUF Thermal Radar 2 具備熱敏電阻排線 - TUF ICe 獨立 TUF 散熱芯片 “We Got Your Back”Shape Force - TUF Fortifier “TUF ENGINE!” 電源設計 - 8+2 相數字電源設計 - TUF Components(10K Ti-Cap 電容、TUF 電感、電 晶體;通過嚴格軍事標準測試) - 華碩 DIGI+ Power Control 程序 “Safe & Stable!”防護設備 - TUF Detective - TUF ESD Guards 2 靜電放電防護 - Dust Defenders 具備插座保護蓋和後側輸出/輸入防塵 保護 - MemOK! 內存救援 其他特殊功能 USB 3.1 Boost 功能提供 USB 3.
SABERTOOTH X99 規格列表 內置 I/O 設備連接端口 2 x USB 3.0/2.0 連接端口可擴展 4 組 USB 3.0 連接端口 (19-pin,米色) 2 x USB 2.0/1.1 連接端口可擴展 4 組 USB 2.0/1.1 連接端口 8 x SATA 6.
產品包裝 在您拿到本主板包裝盒之後,請馬上檢查下面所列出的各項標準配件是否齊全。 nual User Ma 華碩 SABERTOOTH X99 主板 用戶手冊、認證 驅動程序與 應用程序 DVD 光盤 6 x Serial ATA 6.0 Gb/s 排線 1 x ASUS SLI™ 橋接連接器 (12 厘米) 1 x ASUS Q-Shield 擋板 1 x 二合一 ASUS Q-Connector 套件 1 x 40 mm 輔助風扇 4 x DRAM 插槽防塵蓋 2 x PCIe x16 插槽防塵蓋 1 x PCIe x1 插槽防塵蓋 1 x PCIe x4 插槽防塵蓋 3 x 熱敏電阻排線 TUF 配件用戶手冊 1 x 插座保護蓋組合 (LAN 保護蓋、前側 USB 3.0 保護蓋) 5 x 音頻插座保護蓋 SA ExprTA ess 9 x SATA 插座蓋 1 x SATA Expresss 插座蓋 11 x 後側面板 USB 插座蓋 2 x 內部 USB 2.
安裝工具與配件 顯卡(選購) Philips (十字) 螺絲刀 PC 機箱 電源供應設備 Intel® LGA2011-v3 處理器 Intel® LGA2011-v3 兼容處理器風扇 內存條 SATA 硬盤 SATA 光驅(選購) 上表所列的工具與元件並不包含在主板包裝盒內。 xix
xx
第一章 1.1 特殊功能 1.1.1 產品特寫 支持 LGA2011-v3 規格的 Intel® Core™ i7 處理器 本主板支持最新 LGA2011-v3 封裝的 Intel® Core™ i7 處理器,並通過 GPU、四 通道 DDR4 內存插槽與 PCI Express 2.0/3.0 擴展插槽,能提供最佳的繪圖顯示與系 統運算性能。 採用 Intel® X99 Express 芯片組 I n t e l ® X99 E x p r e s s 芯片組採用最新的單芯片設計,是專為支持最新的 LGA2011-v3 插槽的 Intel® Core™ i7 處理器所設計,通過連續的點對點鏈接增加帶 寬與穩定性,並增強系統性能。原生支持高達 8 組 USB 3.0 連接端口、14 組 SATA 6Gb/s 連接端口與 M.2 規格,提供更快速的數據存取速度。 PCI Express® 3.0 最新的 PCI Express 3.0(PCIe 3.0)總線標準提供比當前 PCIe 2.0 快二倍的性能 與速度,PCIe 3.0 可以與 PCIe 1.0 及 PCIe 2.
支持雙 PCIe 3.0 x4 M.2 規格 通過 4 x PCI Express 3.0/2.0 帶寬,M.2 插槽數據傳輸率最高可達 32 Gb/s,可 以用來增強指定給操作系統使用的 SSD 的性能。M.2 插槽也支持 Intel Rapid Storage 技術,可以更快速的讀取數據與應用程序,以及更快速地喚醒系統。 第一章 完全集成 USB 3.1 本主板內置最新的 USB 3.1 雙 Type-A 連接端口,提供最快速的 USB 數據傳輸, 您將體驗高達 10 Gb/s,或比 USB 3.0 快二倍速度的傳輸率。新一代標準完全向下 兼容您既有的 USB 設備,讓您盡情享受 USB 3.1 驚人的傳輸速度。 1.1.
1.1.3 “TUF ENGINE!” 電源設計 數字電源控制 第一章 華碩 DIGI+ 電源控制包括有多重數字電壓控制器,可以極精準的調控 VRAM、 DRAM 內存與處理器。這項革命性的創新與領先企業的華碩技術提供極度精確的電 壓,帶給您最佳的效率、穩定性與系統性能。 TUF Components(電感、電容 & 電晶體;軍用標準認證) 本主板擁有堅固耐用且符合軍用標準的 T U F 新電感、鈦全固態電容及電晶體 (MOSFET),且通過嚴格的軍事標準測試,即使在嚴峻的情況下依然能有傑出優異 的表現。TUF 電感是由多種金屬混合物取代鐵所製成,可以支持高達 40A 的額定電 流量,高於常規的元件。此外,單一包裝消除震動雜訊的生成,在最嚴峻的狀態下也 能發揮優秀的特性與耐久性。 1.1.
1.1.5 華碩 EZ DIY 華碩 UEFI BIOS(EZ Mode) 第一章 華碩 UEFI BIOS 程序提供可由鼠標控制操作的友善的圖像化界面,在超越常規鍵 盤的 BIOS 控制,為您提供更多的靈活性、方便性與易於瀏覽 UEFI BIOS,相較常規 的 BIOS 版本,可以提供您雙選擇模式和支持原生大於 2.
1.1.
1.1.
1.2 主板概述 1.2.
1.2.2 主板結構圖 第一章 關於面板連接插座與內部連接插座的相關信息,請參考 1.2.9 內部連接 端口 與 2.3.
主板元件說明 頁數 1. DDR4 DIMM slots 1-11 2. CPU, optional, chassis, and assistant fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-4; 4-pin ASST_FAN1-5) 1-32 3. LGA2011-v3 socket 1-10 4. ATX power connectors (24-pin EATXPWR, 12-pin EATX12V) 1-34 5. MemOK! button 1-24 6. USB 3.0 connector (20-1 pin USB3_12, USB3_34) 1-29 ® 7. Intel X99 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1-2 [beige]; SATA6G_3-4 [gray] SATA Express [gray at the top]); SATA6G_7-10 [black] 1-28 8. M.
1.2.
1.2.
內存設置 您可以任意選擇使用 2GB、4GB 與 8GB 的 unbuffered non-ECC DDR3 內存條至 本主板的內存插槽上。 第一章 • 您可以在 Channel A、Channel B、Channel C、Channel D 安裝不同 容量的內存條,在四通道設置中,系統會檢測較低容量通道的內存容 量。任何在較高容量通道的其他內存容量,會被檢測為單通道模式運 行。 • 根據 Intel 處理器規格,建議內存電壓低於 1.65V 以保護處理器。 • 由於 32-bit Windows 操作系統內存地址的限制,當您安裝 4GB 或 更多的內存條時,系統實際可用的總內存只有 3GB 或更少。為充分 利用內存,您可以運行以下任一動作: a) 若您使用 32-b i t W i n d o w s 操作系統,建議系統內存最高安裝 3GB 即可。 b) 當 您的主板安裝 4G B 或更多的內存時,建議您安裝 64-b i t Windows 操作系統。 c) 若需要更詳細的數據,請訪問 Microsoft 網站 http://support. microsoft.
SABERTOOTH X99 主板合格供應商列表(QVL) DDR4 3333MHz 內存插槽支持 (選購) 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 G.SKILL F4-3333C16Q-16GRK 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 16-1616-36 1.35V 2 4 • • 8 第一章 供應商 DDR4 3300MHz 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 G.SKILL F4-3300C16Q-16GRK 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 16-16-16-36 1.35V 內存插槽支持 (選購) 2 4 • • 8 DDR4 3200MHz 內存插槽支持 (選購) 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 2 4 G.
DDR4 3000MHz 內存插槽支持 (選購) 第一章 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 2 4 G.SKILL F4-3000C15Q-32GRR 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 15-15-15-35 1.35V • • G.SKILL F4-3000C15Q-32GRB 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 15-15-15-35 1.35V • • G.SKILL F4-3000C15Q-32GRK 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 15-15-15-35 1.35V • • G.SKILL F4-3000C16Q-32GRR 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 16-16-16-36 1.35V • • G.
DDR4 2800MHz 內存插槽支持 (選購) 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 2 4 A_DATA AX4U2800W8G17-DRZ 8GB DS SK hynix H5AN4G8NMFR 17-18-18-36 1.2V • • A_DATA AX4U2800W4G17 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 17-17-17-36 1.2V • • A_DATA AX4U2800W4G17 32GB(4GB*8) SS SK hynix H5AN4G8NMFR 17-17-17-36 1.2V • • A_DATA AX4U2800W8G17 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 17-17-17-36 1.2V • • AVEXIR AVD4U28001604G-4CI 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 16-16-16-36 1.
DDR4 2666MHz 內存插槽支持 (選購) 第一章 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 2 4 CORSAIR CMD16GX4M4A2666C14 16GB(4GB*4) SS - - 14-16-16-35 1.2V • • CORSAIR CMD32GX4M4A2666C14 32GB(8GB*4) DS - - 14-16-16-35 1.2V • • CORSAIR CMK16GX4M4A2666C15 16GB(4GB*4) SS - - 15-17-17-35 1.2V • • CORSAIR CMK32GX4M4A2666C15 32GB(8GB*4) DS - - 15-17-17-35 1.2V • • CORSAIR CMK16GX4M4A2666C14R 16GB(4GB*4) SS - - 14-16-16-35 1.
DDR4 2400MHz 內存插槽支持 (選購) 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 2 4 A_DATA AX4U2400W8G16-DRZ 8GB SS SK hynix H5AN4G8NMFR 16-16-16-39 1.2V • • AVEXIR AVD4U24001604G-4M 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 16-16-16-39 1.2V • • • AVEXIR AVD4U24001504G-4CI 16GB(4GB*4) SS SK hynix H5AN4G8NMFR 15-15-15-35 1.2V • • • AVEXIR AVD4U24001608G-4M 32GB(8GB*4) DS SK hynix H5AN4G8NMFR 16-16-16-39 1.
DDR4 2133MHz 內存插槽支持 (選購) 第一章 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 1 2 4 Micron MTA8ATF51264AZ-2G1A1 4GB SS Micron D9RGQ 15-15-15-37 1.2V • • • Micron MTA16ATF1G64AZ-2G1A1 8GB DS Micron D9RGQ 15-15-15-37 1.2V • • • Crucial CT4G4DFS8213.8FA1 4GB SS Micron D9RGQ 15-15-15-37 1.2V • • • Crucial CT8G4DFD8213.16FA1 8GB DS Micron D9RGQ 15-15-15-37 1.2V • • • Samsung M378A5143DB0-CPB 4GB SS Samsung K4A4G085WD 15-15-15-36 1.
DDR4 2133MHz(表格接上頁) 內存插槽支持( 選購) 供應商 型號 容量 SS/ DS 芯片廠牌 芯片型號 時鐘 電壓 1 2 CORSAIR CMD32GX4M4A2133C12 32GB(8GB*4) DS - - 12-1414-27 1.2V • • G.SKILL F4-2133C15Q-16GRR 16GB(4GB*4) SS - - 15-1515-35 1.2V • • G.SKILL F4-2133C15Q-16GRB 16GB(4GB*4) SS - - 15-1515-35 1.2V • • G.SKILL F4-2133C15Q-16GRK 16GB(4GB*4) SS - - 15-1515-35 1.2V • • G.SKILL F4-2133C15Q-32GRR 32GB(8GB*4) DS - - 15-1515-35 1.2V • • G.
SS - 單面內存 DS - 雙面內存 內存插槽支持: • 1 - 在單通道內存設置中,支持安裝一組內存條在任一插槽,建議您 安裝在 D1 插槽。 第一章 • 2-支 持安裝二組內存條在米色插槽,作為一對雙通道設置,建議您 安裝在 B1 與 D1 插槽以獲得更佳的兼容性。 • 4-支 持安裝四組內存條在二個米色和二個黑色插槽,作為二對雙通 道設置。建議您安裝在 A1、B1、C1 與 D1 插槽以獲得更佳的兼 容性。 • 6-支 持安裝六組內存條在四個米色和二個黑色插槽,作為三對雙通 道設置。建議您安裝在 A1、B1、B2、C1、D1 與 D2 插槽以獲 得更佳的兼容性。 • 8-支 持安裝八組內存條在所有插槽,作為全負載四雙通道設置。 • 華碩獨家提供支持高速內存功能。 • 對高速內存的支持會受到特定處理器之物理特性的影響。載入 BIOS 程序中的 X.M.P. 或 D.O.C.P. 設置來支持高速內存。 • 請訪問華碩網站(w w w.a s u s.c o m.
1.2.5 擴展插槽 第一章 安裝或卸除任何擴展卡之前,請暫時先將電腦的電源線拔出。如此可免 除因電氣殘留於電腦中而發生的意外狀況。 插槽編號 插槽說明 1 PCIe 3.0/2.0 x16_1 插槽 2 PCIe 2.0 x4_1 插槽 3 PCIe 3.0/2.0 x16_2 插槽 4 PCIe 2.0 x1_1 插槽 5 PCIe 3.0/2.
40-LANE CPU PCI Express 3.0 運行模式 PCIe 3.0/2.0 x16_1 PCIe 3.0/2.0 x16_2 PCIe 3.0/2.0 x16_3 一張 VGA/PCIe 顯卡 x16 (建議使用單張顯 卡) N/A N/A 二張 VGA/PCIe 顯卡 x16 x16 N/A 三張 VGA/PCIe 顯卡 x16 x16 x8 VGA 設置 第一章 PCI Express 3.0 運行模式 28-LANE CPU PCIe 3.0/2.0 x16_1 PCIe 3.0/2.0 x16_2 PCIe 3.0/2.
A B C D E F G H PCIe x16_1 共享 – – – – – – – PCIe x16_2 共享 – – – – – – – PCIe x16_3 共享 – – – – – – – – – – 共享 – – – – PCIe x4_1 – – 共享 – – – – – ASM 1142 共享 – – – – – – – SMBUS 控制器 – – 共享 – – – – – SATA #0 – 共享 – – – – – – GbE 控制器 – – – – 共享 – – – EHCI #0 – – – – – – – 共享 EHCI #1 – – 共享 – – – – – XHCI 控制器 – – – – – – – 共享 Realtek 8111GR – – – 共享 – – – – Intel 網絡 I218 – – 共享 – – –
1.2.6 主板上的內置按鈕與開關 當您想要針對未安裝在機箱的裸板或是開放機箱的系統作性能調校時,主板上內置 的按鈕與開關可以方便您迅速地開關機或是重置系統。這是想要不斷更改設置以提升 系統性能的超頻者和玩家最理想的設置方式。 第一章 1. MemOK! 按鈕 在主板上安裝不兼容的內存條可能會導致啟動失敗,而且在 MemOK 按鈕旁的 DRAM_LED 指示燈也會一直亮著。按住 MemOK! 按鈕直到 DRAM_LED 指示燈 開始閃爍,即開始自動將內存調整為兼容直到成功啟動。 • 請參考 1.2.
1.2.7 跳線選擇區 在主板上的 CMOS 內存中記載著正確的時間與系統硬件配置等數據,這些數據並 不會因電腦電源的關閉而遺失數據與時間的正確性,因為這個 CMOS 的電源是由主 板上的鋰電池所供應。 想要清除這些數據,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 將 CLRTC 跳線帽由 [1-2](默認值)改為 [2-3] 約五∼十秒鐘(此時即清 除 CMOS 數據),然後再將跳線帽改回 [1-2]。 3. 插上電源線,開啟電腦電源。 4. 當啟動步驟正在進行時按著鍵盤上的 鍵進入 BIOS 程序畫面重新設 置 BIOS 數據。 除了清除 CMOS 配置數據之外,請勿將主板上 CLRTC 的跳線帽由默認 值的位置卸除,因為這麼做可能會導致系統啟動失敗。 • 若上述步驟無效,請卸除主板上的內置電池並再次卸除跳線帽以清除 CMOS 配置數據。在 CMOS 配置數據清除後,再重新裝回電池。 • 如果您是因為超頻的緣故導致系統無法正常啟動,您無須使用上述的 配置數據清除方式來排除問題。建議可以採用 C.P.
2.
1.2.8 內置 LED 指示燈 P O S T 狀態指示燈用來在主板啟動過程中依序檢查重要元件,包括處理器、 內存、V G A 顯卡與硬盤,若是出現錯誤,在出現問題設備旁的指示燈會持續亮 著,直到問題解決才會熄滅。 華碩 SABERTOOTH X99 主板用戶手冊 1-27 第一章 1.
1.2.9 內部連接端口 1. Intel ® Z97 Serial ATA 6.0 Gb/s 設備連接插槽(7-pin SATA6G_1-2 [米色], SATA6G_3-4 [灰色], SATA EXPRESS [灰色上端], SATA6G_7-10 [黑色]) 第一章 這些插槽可支持使用 Serial ATA 6.0 Gb/s 排線來連接 Serial ATA 6.0 Gb/s 硬盤。 若您安裝了 Serial ATA 硬盤,您可以通過 Intel® Rapid Storage 技術,與內置 的 Intel® Z97 芯片組來創建 RAID 0、RAID 1、RAID 5、RAID 10 磁盤陣列。 將 SATA 數據線上的直角接口端 (right angle side)連接在 SATA 設備上,或是將直角接口端安裝至 主板內置的 SATA 連接端口,以避 免造成與較大顯卡的衝突。 ‧ 這些插槽的默認值為 [AHCI Mode],若您想要使用這些插槽來建構 Serial ATA RAID 功能,請將 BIOS 程序中的 SATA Mode 項目設置 為 [RAID Mode]。請參考 3.6.
2. USB 3.0 連接插槽(20-1 pin USB3_12, USB3_34) 第一章 這個插槽用來連接 USB 3.0 模塊,可在前面板或後側連接端口擴展 USB 3.0 模塊。當您安裝 USB 3.0 模塊,您可以享受 USB 3.0 的益處,包括有更快的數 據傳輸率最高達 5Gb/s、對可充電的 USB 設備更快的充電速度、最佳化能源效 率,以及與 USB 2.0 向下兼容。 USB 3.0 模塊為選購配備,請另行購買。 • 這個插槽是以 xHCI 規格為基礎,建議您在 Windows 7 操作系統中 安裝相關的驅動程序來充分使用 USB 3.0 插槽。 • 安裝的 USB 3.0 設備視操作系統設置而運行在 xHCI 或 EHCI 狀態。 • 這些 USB 3.0 連接端口在您使用 USB 3.1 Boost 功能時,支持 Windows 8/Windows 8.
3.
4. USB 2.0 連接插槽(10-1 pin USB1112, USB1314) 第一章 這些 USB 擴展套件排線插槽支持 USB 2.0 規格,將 USB 模塊排線連接至任 何一個插槽,然後將模塊安裝到機箱後側面板中開放的插槽。這些 USB 插槽與 USB 2.0 規格兼容,並支持傳輸速率最高達 480 MBps。 請勿將 1394 排線連接到 USB 插槽上,這麼做可能會導致主板的損毀。 若是您的機箱擁有前面板 U S B 連接端口,您可以將前面板 U S B 排線 連接至 ASUS Q-Connector(USB,深咖啡色),然後將 Q-Connector (USB)安裝至主板內置的 USB 插槽上。 USB 2.
5.
6. 前面板音頻連接排針(10-1 pin AAFP) 第一章 這組音頻外接排針供您連接到前面板的音頻排線,除了讓您可以輕鬆地通過主 機前面板來控制音頻輸入/輸出等功能,並且支持 AC’97 或 HD Audio 音頻標 準。將前面板音頻輸出/輸入模塊的連接排線之一端連接到這個插槽上。 • 建議您將支持高保真(high definition)音頻的前面板音頻模塊連接 到這組排針,如此才能獲得高保真音頻的功能。 • 若是要將高保真音頻前面板模塊安裝至本接針,請將 B I O S 程序中 Front Panel Type 項目設置為 [HD];若要將 AC 97 音頻前面版模塊 安裝至本接針,請將 BIOS 程序設置為 [HD] 或 [AC97]。 7.
8. 主板電源插槽(24-pin EATXPWR, 8-pin EATX12V) 這些電源插槽用來連接一個 ATX +12V 電源。電源所提供的連接插頭已經過 特別設計,只能以一個特定方向插入主板上的電源插槽。找到正確的插入方向 後,僅需穩穩地將之套進插槽中即可。 第一章 • 建議您使用與 2.
9.
10. TPM 插座(20-1 pin TPM) 這個插座支持可信任安全平台模塊(T P M)系統,用來安全地保存金鑰、數 字認證、密碼和數據。可信任安全平台模塊(TPM)系統也用來協助加強網絡安 全,保護數字身分,以及確保平台的安全性。 第一章 11.
12. Thunderbolt 接口(5-pin TB_HEADER) 第一章 這個插槽用來連接附加的 Thunderbolt I/O 卡,以支持 Intel Thunderbolt 技 術,您可以在一個串接設置中連接最高達七個支持 Thunderbolt 的設備與一個支 持 DisplayPort 的顯示設備。 附加的 Thunderbolt I/O 卡與 Thunderbolt 排線為選購配備,請另行購 買。 13. M.2 插槽 3 這個插槽用來安裝 M.2 (NGFF) SSD 模塊。 • 這個插槽支持 M Key 與 2242/2260/2280 類型存儲設備。 • M.2 插槽 3 與 PCIe x16_3 插槽共享帶寬。請參考 3.6.3 PCH 存儲 設備設置(PCH Storage Configuration) 一節的詳細說明。 M.
14. 機箱開啟警示排針(4-1 pin CHASSIS) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外,尚須 搭配一個外接式檢測設備譬如機箱開啟檢測感應器或者微型開關。在本功能啟用 時,若您有任何移動機箱元件的動作,感應器會隨即檢測到並且送出一信號到這 組接針,最後會由系統記錄下來這次的機箱開啟事件。 第一章 本項目的默認值是將跳線帽套在 CHASSIS 排針中標示著「Chassis Signal」和 「GND」的二個針腳上,若您想要使用本功能,請將跳線帽從「Chassis Signal」 和「GND」的針腳上卸除。 當您連接至這個排針、第一次切換至這個排針,或是再次連接至這個排 針時,會顯示通知信息,請重新啟動系統以關閉該信息。 15.
第二章 2.1 創建您的電腦系統 2.1.1 安裝主板 本章節的圖標只能參考,主板的結構可能會隨著型號而有所不同,但是 安裝的步驟仍然是相同的。 1. 安裝華碩 Q-Shield 擋板至機箱的後側 I/O 面板。 2.
3.
2.1.
A A B C B 第二章 2-4 第二章:硬體設備信息
2.1.
2.1.
第二章 2.1.
2.1.
2.1.7 安裝前面板輸出/輸入連接端口 PWR Ground Reset Ground HDD LED R SW POWE RESET SW 第二章 HDD LED+ HDD LED- HDD LED 安裝 ASUS Q-Connector 安裝 USB 2.0 連接插槽 安裝前面板音頻連接插槽 AAFP USB 2.0 安裝 USB 3.0 連接插槽 USB 3.
2.1.
2.2 BIOS 更新應用程序 USB BIOS Flashback USB BIOS Flashback 提供最簡單更新 BIOS 的方法。用戶可以輕鬆嘗試使用新的 BIOS 版本來進行超頻,不需要進入 BIOS 或操作系統,只要插入 USB 存儲設備然後 按下 BIOS Flashback 按鈕三秒鐘,BIOS 程序就會自動在待機狀態下更新。 請依照以下步驟使用 USB BIOS Flashback: 1. 將包裝盒內附的驅動程序與應用程序 DVD 光盤放入光驅,然後安裝 USB BIOS Flashback 安裝向導。請依照屏幕指示的步驟來完成程序的安裝。 2. 將 USB 存儲設備插入 USB Flashback 連接端口。 • 建議您使用 USB 2.0 存儲設備來保存最新的 BIOS,可以獲得更好的 兼容性與穩定性。 3. 啟動 USB BIOS Flashback 安裝向導來自動下載最新的 BIOS。 4. 按下 BIOS Flashback 按鈕約三秒鐘直到指示燈開始閃爍,表示 BIOS Flashback 功能已經啟動。 5.
2.3 主板後側與音頻連接端口 2.3.1 後側面板連接端口 第二章 後側面板連接端口 1. USB 2.0 連接端口 7-10 6. USB 3.1 連接端口,支持 ASUS USB 3.1 Boost 2. TUF Detective 7. USB 3.0 連接端口,支持 ASUS USB 3.1 Boost 3. Intel® LAN(RJ-45)網絡連接* 8. USB 3.0 連接端口 5-6,支持 ASUS USB 3.1 Boost 底端連接端口支持 USB BIOS Flashback 4. Realtek® LAN(RJ-45)網絡 連接* 9. S/PDIF 光纖排線輸出連接端口 5. USB BIOS Flashback 按鈕 10.
• USB 3.1/3.0 設備只能用來作為數據磁盤。 • 強烈建議您將 USB 3.1 設備連接至 USB 3.1 連接端口、USB 3.0 設 備連接至 USB 3.0 連接端口,才能讓您的 USB 設備獲得更快更好的 性能表現。 • 由於 Intel® 9 系列芯片組的設計,所有連接至 USB 2.0 與 USB 3.
2.3.2 音頻輸出/輸入連接圖標說明 音頻輸出/輸入連接端口 橘色 淺藍色 黑色 草綠色 粉紅色 連接耳機與麥克風 第二章 連接立體聲喇叭 連接 2.
連接 4.1 聲道喇叭 第二章 連接 5.1 聲道喇叭 連接 7.
2.4 第一次啟動電腦 1. 確認所有排線與接腳都接妥,然後蓋上機箱的外蓋。 2. 確定所有的開關都已關閉 3. 將電源線接上機箱背面的電輸入插座。 4. 情況許可的話,最好將電源線路上加接突波吸收/保護器。 5. 您可以先開啟以下周邊的電源: a. 顯示屏 b. 外接式 SCSI 接口外圍設備(從串連的最後端開始) c. 系統電源(ATX 的電源不會因為送電而馬上動作,而是等待面板上的按鈕 動作後才會工作) 第二章 6.
第三章 3.
3.
3.2.1 EZ Mode 本主板的 BIOS 設置程序的默認值為 EZ Mode。您可以在 EZ Mode 中查看系統 基本數據,並可以選擇顯示語言、喜好設置及啟動設備順序。若要進入 Ad vanced Mode,請點擊畫面右下角 Advanced Mode,或是按下 快捷鍵。 進入 BIOS 設置程序的畫面可個人化設置,請參考 3.
3.2.
功能表列 BIOS 設置程序最上方各菜單功能說明如下: My Favorites 本項目將記錄時常使用的系統設置及設置值。 Main 本項目提供系統基本設置。 Ai Tweaker 本項目提供超頻設置。 Advanced 本項目提供系統高級功能設置。 Monitor 本項目提供溫度、電源及風扇功能設置。 Boot 本項目提供啟動磁盤設置。 Tool 本項目提供特殊功能設置。 Exit 本項目提供退出 BIOS 設置程序與出廠默認值還原功能。 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,即選擇 M a i n 菜單所出現的項 目。 點擊菜單中的其他項目(例如:Ai Tweaker、Advanced、Monitor、Boot 與 Exit)也會出現該項目不同的選項。 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記,代表此為子菜單,您可利用 方向鍵來選擇,並按下 鍵來進入子菜單。 語言 第三章 這個按鈕位在功能表列的上方,用來選擇 BIOS 程序界面顯示的語言。點擊這個按 鈕來選擇您想要的 BIOS 畫面顯示語言。 我的最愛(F3) 這個按鈕位
快速筆記(F9) 按下此按鈕,可讓您針對已在 BIOS 中進行的設置輸入筆記。 • 快速筆記不支持以下鍵盤功能:刪除、剪下、複製與貼上。 • 您只能使用英文字母與數字來輸入筆記。 快捷鍵 這個按鈕位在功能表列的上方,包含有 BIOS 程序設置的導引方向鍵,使用箭頭按 鍵來選擇菜單中的項目並更改設置。 滾動條 在菜單畫面的右方若出現滾動條,即代表此頁選項超過可顯示的畫面,您可利用上 /下方向鍵或是 PageUp/PageDown 鍵來切換畫面。 線上操作說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。使用 按鍵來抓取 BIOS 屏幕畫面,並保存至攜帶式存儲設備。 設置值 此區域顯示菜單項目的設置值。這些項目中,有的功能選項僅為告知用戶當前運行 狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方向鍵 移動項目時,被選擇的項目以反白顯示。 設置值被選擇後以反白顯示。要改變設置值請選擇此項目,並按下 鍵以顯 示設置值列表。 上次修改的設置按鈕 按下此按鈕可查看您在 BIOS 設置中上一次所做的修改項目。 第三章 3
3.2.
手動設置風扇 從設置文件清單中選擇 Manual 來手動設置風扇運行的速度。 速度點 點擊或輕觸以手動設置風扇 第三章 請依照以下步驟設置風扇: 1. 選擇想要設置的風扇並查看該風扇現在的狀況。 2. 點擊並拖曳速度點來調整風扇的運行速度。 3.
3.2.4 EZ Tuning 向導 EZ Tuning 向導用來超頻處理器和內存條、電腦使用與處理器風扇至最佳設置。通 過這個功能您也可以輕鬆設置系統的 RAID 功能。 系統超頻設置 RAID 設置 第三章 調整系統設置 請依照以下步驟調整設置: 1. 在鍵盤按下 鍵或在 B I O S 程序畫面中點擊 Tuning 向導窗口,然後點擊 下一步(Next)。 來啟動 E Z 2. 選擇電腦狀態為 Daily Computing 或 Gaming/Media Editing,然後點擊 下一步 (Next)。 3. 選擇安裝的處理器風扇類型(Box cooler、Tower cooler 或 Water cooler)然後 點擊 下一步(Next)。 若是無法確定處理器風扇類型,點擊 我不確定(I’m not sure),系統 將會自動檢測處理器風扇類型。 4.
創建 RAID 請依照以下步驟創建 RAID: 1. 在鍵盤按下 鍵或在 B I O S 程序畫面中點擊 Tuning 向導窗口,然後點擊 下一步(Next)。 來啟動 E Z 2. 點擊 RAID 然後點擊 下一步(Next)。 • 請確認硬盤中沒有已存在的 RAID 磁盤。 • 請確認硬盤已經連接至 Intel® SATA 連接端口。 3. 選擇 RAID 的保存類型為 Easy Backup 或 Super Speed,然後點擊 下一步 (Next)。 a. 若為 Easy Backup,點 擊 下一步(N e x t) 然 後選擇從 Easy Backup (R A I D1) 或 E a s y Backup (RAID10)。 若您安裝了四個硬 盤,可以只選擇 Easy Backup (RAID 10)。 b. 第三章 若為 Super Speed,點 擊 下一步(N e x t) 然 後選擇從 Super Speed (R A I D0) 或 S u p e r Speed (RAID5)。 4.
3.
新增項目至我的最愛 請依照以下步驟新增項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程序畫面中點擊 圖畫面。 來啟動設置樹狀 2. 在設置樹狀圖畫面中選擇想要保存至我的最愛的 BIOS 項目。 主菜單面板 已選擇的快 捷方式項目 子菜單面板 3. 從主菜單面板選擇項目,然後點擊子菜單中想要保存至我的最愛的選項,再點擊 或輕觸 或是按下 按鍵。 以下項目無法加入至我的最愛: 第三章 • 有子菜單的項目。 • 用戶自訂項目,例如:語言、啟動設備順序。 • 設置項目,例如:內存 SPD 信息、系統時間與日期。 4. 點擊 Exit (ESC) 或按下 鍵來關閉樹狀圖窗口。 5.
3.4 主菜單(Main Menu) 當您進入 BIOS 設置程序的高級模式(Advanced Mode)時,首先出現的第一個 畫面即為主菜單。主菜單顯示系統信息概要,用來設置系統日期、時間、語言與安全 設置。 安全性菜單(Security) 第三章 本菜單可讓您改變系統安全設置。 • 若您忘記設置的 BIOS 密碼,可以採用清除 CMOS 實時鐘(RTC) 內存。請參考 1.2.6 主板上的內置按鈕與開關 一節的說明。 • Administrator 或 User Password 項目默認值為 Not Installed,當您 設置密碼之後將顯示為 Installed.
系統管理員密碼(Administrator Password) 當您設置系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設置程序中的某 些信息無法查看或更改設置。 設置系統管理員密碼 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 窗口輸入欲設置的密碼,輸入完成按下 。 3. 請再一次輸入密碼以確認密碼正確。 更改系統管理員密碼 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
3.
以下項目只有在 CPU Strap 設置為 [100MHz]、[125MHz]、[166MHz] 或 [250MHz] 時才會出現。 Source Clock Tuner [Auto] 本項目用來依照指派的 CPU strap 選擇來源時鐘以獲得更好的超頻能力。 設置值有:[8Ohm dbl] [7Ohm dbl] [6Ohm dbl] [5Ohm dbl] [4Ohm dbl] [3Ohm dbl] [2Ohm dbl]。 PLL Selection [Auto] 本項目設置 LC PLL 為默認值以獲得更好的穩定度。當 BCLK(基本時鐘)已 經超過 100MHz 很多時請選擇 SB PLL。這項設置可能會影響其他需要精確時鐘 頻率的設備。設置值有:[Auto] [LC PLL] [SB PLL]。 Filter PLL [Auto] 當您使用很高的 BCLK(基本時鐘)時將本項目設置為 High BCLK Mode 來增 進超頻性能。設置值有:[Auto] [Low BCLK Mode] [High BCLK Mode]。 BCLK Frequency [Auto] 本項目用來設置 BCLK 頻率
2-Core Ratio Limit [Auto] [Auto] 選擇並應用 CPU 默認的 Turbo 倍頻設置。 [Manual] 選擇手動指定 2-Core Ration Limit 數值高於或等於 3-Core Ratio Limit。 若您要設置 2-Core Ratio Limit 數值,請勿將 1-Core Ratio Limit 設置為 [Auto]。 3-Core Ratio Limit [Auto] [Auto] 選擇並應用 CPU 默認的 Turbo 倍頻設置。 [Manual] 選擇手動指定 3-Core Ration Limit 數值高於或等於 4-Core Ratio Limit。 若您要設置 3-Core Ratio Limit 數值,請勿將 1-Core Ratio Limit 與 2-Core Ratio Limit 設置為 [Auto]。 4-Core Ratio Limit [Auto] [Auto] 選擇並應用 CPU 默認的 Turbo 倍頻設置。 [Manual] 選擇手動指定 4-Core Ration Limit 數值高於或等於 3-Core Rati
Min CPU Cache Ratio [Auto] 本項目用來設置處理器的非核心比值至可能的最小值。使用 <+> 與 <-> 按鍵來調 整數值。更改的範圍會依安裝的處理器而異。 Max CPU Cache Ratio [Auto] 本項目用來設置處理器的非核心比值至可能的最大值。使用 <+> 與 <-> 按鍵來調 整數值。更改的範圍會依安裝的處理器而異。 第三章 3-18 第三章:BIOS 程序設置
Internal PLL Overvoltage [Auto] 本項目用來設置 Internal PLL 電壓,讓 K 型號的處理器能獲得最大的超頻性能。 設置值有:[Auto] [Enabled] [Disabled]。 BCLK Frequency : DRAM Frequency Ratio [Auto] 本項目用來設置 BCLK 頻率到內存頻率比值。 [Auto] 內存速率設為最優化設置。 [100:100] BCLK 頻率到內存頻率比為 100:100。 [100:133] BCLK 頻率到內存頻率比為 100:133。 DRAM Frequency [Auto] 本項目可讓您設置內存的運行頻率。設置選項會隨著 BCLK Frequency 設置值 變動。設置值有:[Auto] [DDR4-800MHz] [DDR4-1000MHz] [DDR4-1067MHz] [D D R4-1200M H z] [D D R4-1333M H z] [D D R4-1400M H z] [D D R4-1600M H z] [D D R4-1800M H z] [D D R4-1866M H z
Primary Timings DRAM CAS# Latency [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# to CAS# Delay [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# PRE Time [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# ACT Time [Auto] 設置值有:[Auto] [1] – [63]。 DRAM Command Rate [Auto] 設置值有:[Auto] [Timing T1] – [Timing T3]。 Secondary Timings DRAM RAS# to RAS# Delay [Auto] 設置值有:[Auto] [1] – [7]。 DRAM RAS# to RAS# Delay L [Auto] 設置值有:[Auto] [1] – [7]。 DRAM REF Cycle Time [Auto] 設置值有:[Auto] [1] – [1023]。 DRAM Refresh Interval [Auto] 設置值有:[Auto
DRAM WRITE to READ Delay [Auto] 設置值有:[Auto] [1] – [15]。 DRAM WRITE to READ Delay(tWTR_L) [Auto] 設置值有:[Auto] [1] – [15]。 DRAM CKE Minimum Pulse Width [Auto] 設置值有:[Auto] [5] – [8]。 DRAM Write Latency [Auto] 設置值有:[Auto] [1] – [31]。 Third Timings tRRDR [Auto] 設置值有:[Auto] [1] - [7]。 tRRDD [Auto] 設置值有:[Auto] [1] - [7]。 tWWDR [Auto] 設置值有:[Auto] [1] - [7]。 tWWDD [Auto] 設置值有:[Auto] [1] - [7]。 tRWDR [Auto] 設置值有:[Auto] [1] - [7]。 第三章 tWRDR [Auto] 設置值有:[Auto] [1] - [7]。 tWRDD [Auto] 設置值有:[Auto] [1] - [7]。 t
tUWRDR [Auto] 設置值有:[Auto] [1] - [3]。 tRWDR2 [Auto] 設置值有:[Auto] [0] - [31]。 tRWDD [Auto] 設置值有:[Auto] [0] - [31]。 tRWSR2 [Auto] 設置值有:[Auto] [0] - [31]。 tWRDD2 [Auto] 設置值有:[Auto] [0] - [31]。 tCCDWR [Auto] 設置值有:[Auto] [0] - [7]。 tCCD_L [Auto] 設置值有:[Auto] [0] - [7]。 RTL IOL control DRAM RTL INIT Value [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHA D0 R0) [Auto] 設置值有:[Auto] [1] - [127]。 第三章 DRAM RTL (CHA D0 R1) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHA D1 R0) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (
華碩 SABERTOOTH X99 主板用戶手冊 3-23 第三章 DRAM RTL (CHC D1 R0) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHC D1 R1) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHD D0 R0) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHD D0 R1) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHD D1 R0) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM RTL (CHD D1 R1) [Auto] 設置值有:[Auto] [1] - [127]。 DRAM IO-L (CHA D0 R0) [Auto] 設置值有:[Auto] [1] - [255]。 DRAM IO-L (CHA D0 R1) [Auto] 設置值有:[Auto] [1] - [255]。 DRAM IO-L (CHA D1 R0) [Auto] 設置值有:[Auto] [1] - [25
第三章 IO control MC Vref(CHA) [Auto] 設置值有:[Auto] [50] - [99.911]。 MC Vref(CHB) [Auto] 設置值有:[Auto] [50] - [99.911]。 MC Vref(CHC) [Auto] 設置值有:[Auto] [50] - [99.911]。 MC Vref(CHD) [Auto] 設置值有:[Auto] [50] - [99.911]。 DRAM Vref (CHA) [Auto] 設置值有:[Auto] [60] - [99]。 DRAM Vref (CHB) [Auto] 設置值有:[Auto] [60] - [99]。 DRAM Vref (CHC) [Auto] 設置值有:[Auto] [60] - [99]。 DRAM Vref (CHD) [Auto] 設置值有:[Auto] [60] - [99]。 CTL Vref (CHAB) Sign [+] 設置值有:[+] [-]。 CTL Vref (CHAB) [Auto] 設置值有:[Auto] [0.00] - [0.
Enhanced Training (CHA/CHB/CHC/CHD) [Auto] 設置值有:[Auto] [Enabled] [Disabled]。 MemTest [Auto] 本項目用來啟動或關閉內存測試。設置值有: [Enabled] [Disabled]。 Attempt Fast Boot [Auto] 本項目用來在啟動速度可能可以加快時,略過內存參考碼的部分。設置值有: [Auto] [Enabled] [Disabled]。 Attempt Fast Cold Boot [Auto] 本項目用來在啟動速度可能可以加快時,略過內存參考碼的部分。設置值有: [Auto] [Enabled] [Disabled]。 華碩 SABERTOOTH X99 主板用戶手冊 3-25 第三章 Receiver CLK Pre-emphasis [Auto] 設置值有:[Auto] [1.00] - [2.00]。 Receiver CLK De-emphasis [Auto] 設置值有:[Auto] [1.00] - [1.
DRAM Training [Auto] 本項目用來讓系統設置 DRAM Training 測試功能。 DRAM SPD Write 本項目只能內存編程高級設置,用來啟動 DRAM SPD Write 功能以進行內存 SMBus 編程。 External DIGI+ Power Control CPU Input Boot Voltage [Auto] 本項目用來設置較高的 CPU 輸入啟動電壓來獲得更好的超頻能力。使用 <+> 與 <-> 按鍵調整數值,設置值以 0.01V 為間隔,更改的範圍由 0.80V 至 2.
VRM Spread Spectrum [Disabled] 本項目可讓您啟動 VRM Spread Spectrum 項目以增加系統穩定性。設置值 有:[Enabled] [Disabled]。 Active Frequency Mode [Disabled] 本項目可讓您啟動 Active Frequency Mode 項目以增強省電性能。設置值有: [Enabled] [Disabled]。 CPU Power Phase Control [Auto] 本項目用來依照 CPU 的需求控制電源相數。設置值有:[Auto] [Standard] [Optimized] [Extreme] [Powe Phase Response]。 當本項目設置為 [Powe Phase Response] 模式時請勿將散熱系統卸除, 散熱環境需受到監控。 以下項目只有在 CPU Power Phase Control 設置為 [Power Phase Response] 時才會出現。 Power Phase Response [Fast] 本項目來為 C P U 設置較快的相式響應以增進系統性能,或是較低的相 式響應
DRAM AB/CD Current Capability (CHA, CHB, CHC, CHD) [100%] 較高的數值提供更大的總電力範圍,同時擴展超頻頻率的範圍。設置值有: [100%] [110%] [120%] [130%]。 DRAM AB/CD Switching Frequency (CHA, CHB, CHC, CHD) [Auto] 本項目用來調整內存切換頻率。指派固定的高內存頻率來增加超頻的範圍,或 低內存頻率以獲得較佳的系統穩定度。設置值有:[Auto] [Manual]。 以下項目只有在 DRAM AB/CD Switching Frequency 設置為 [Manual] 時才會出現。 Fixed DRAM Switching Frequency (KHz) [500] 本項目用來設置固定的內存頻率。使用 <+> 與 <-> 鍵調整數值,設置值以 50kHz 為間隔,更改的範圍從 300kHz 至 550kHz。 DRAM Power Phase Control (CHA, CHB, CHC, CHD) [Auto] [Auto] 設置自動模式。 [Optimized]
Turbo Mode [Enabled] 本項目用來設置核心處理器的速度,使其在運行電力、電流與溫度條件限制 下,可以比基本運行頻率更快的速度運行。設置值有:[Disabled] [Enabled]。 以下項目只有在 Turbo Mode 設置為 [Enabled] 時才會出現。 Turbo Mode 參數 Long Duration Package Power Limit [Auto] 本項目用來設置渦輪倍頻(turbo ratio)的瓦數,默認值為散熱設計功率 (thermal design power)。請使用 <+> 與 <-> 鍵調整數值,數值更改的範 圍為 1W 至 4096W。 Package Power Time Window [Auto] 本項目用來設置渦輪倍頻(turbo ratio)維持的時間長度。請使用 <+> 與 <-> 鍵調整數值,數值更改的範圍為 1 至 127 秒。 Short Duration Package Power Limit [Auto] 本項目用來設置渦輪倍頻(turbo ratio)的更高瓦數來提供系統保護,默 認值為 long duration limit 的
Fully Manual Mode [Disabled] 啟動本項目來設置 CPU 的相關電壓,這個華碩獨家的全手動模式提供最佳的電壓 調整能力,CPU 核心、緩存與系統代理電壓都能各自調整而不受到 CPU 的限制。設 置值有:[Disabled] [Enabled]。 CPU Core Voltage [Auto] 本項目用來設置處理器核心的電壓饋電數量。當核心頻率增加時請提高電壓數量。 設置值有:[Auto] [Manual Mode] [Offset Mode]。 以下項目只有在 CPU Core Voltage 設置為 [Manual Mode] 時才會出現。 CPU Core Voltage Override [Auto] 本項目用來設置處理器核心電壓覆寫。請使用 <+> 與 <-> 鍵調整數值,設置值 以 0.001V 為間隔,更改的範圍從 0.001V 至 1.
以下項目只有在 CPU Cache Voltage 設置為 [Manual Mode] 時才會出 現。 CPU Cache Voltage Override [Auto] 本項目用來設置處理器緩存電壓覆寫。默認值為依照安裝的處理器所得的標準 數值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間隔,更改的範圍從 0.001V 至 1.920V。 以下項目只有在 CPU Core Voltage 設置為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] [+] 設置正數值偏移電壓。 [–] 設置負數值偏移電壓。 CPU Cache Voltage Offset 本項目用來設置 CPU Cache Voltage Offset。默認值為依照安裝的處理 器所得的標準數值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間 隔,更改的範圍從 0.001V 至 0.
CPU SVID Support [Auto] 當系統超頻時將本項目設置為 [Enabled]。關閉 SVID 支持以中斷處理器與外接電 壓調節器的連線。設置值有:[Auto] [Disabled] [Enabled]。 以下項目只有在 CPU SVID Support 設置為 [Enabled] 時才會出現。 SVID Voltage Override [Auto] 本項目用來設置 S V I D 電壓覆寫。默認值為依照安裝的處理器所得的標準數 值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間隔,更改的範圍從 0.001V 至 2.440V。 CPU Input Voltage [Auto] 本項目用來設置處理器的輸入電壓。默認值為依照安裝的處理器所得的標準數值。 請使用 <+> 與 <-> 鍵調整數值,設置值以 0.010V 為間隔,更改的範圍從 0.800V 至 2.700V。 DRAM Voltage [Auto] 本項目用來設置內存電壓。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.005V 為 間隔,更改的範圍從 1.20V 至 1.
PCH I/O Voltage [Auto] 本項目用來設置 PCH(Platform Controller Hub)的 I/O 電壓。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.0125V 為間隔,更改的範圍從 1.2000V 至 2.20000V。 VCCIO CPU 1.05V Voltage [Auto] 本項目用來設置 CPU REF 的主要電源供應。請使用 <+> 與 <-> 鍵調整數值,設 置值以 0.00625V 為間隔,更改的範圍從 0.7000V 至 1.8000V。 VCCIO PCH 1.05V Voltage 本項目用來設置 PCH REF 的主要電源供應。請使用 <+> 與 <-> 鍵調整數值,設 置值以 0.00625V 為間隔,更改的範圍從 0.7000V 至 1.8000V。 VTTDDR Voltage (CHA, CHB, CHC, CHD) [Auto] 本項目用來設置系統內存的終端電壓。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.0125V 為間隔,更改的範圍從 0.6000V 至 1.
3.
3.6.
Intel Virtualization Technology [Disabled] [Enabled] 啟動 Intel 虛擬技術(Virtualization Technology)讓硬件平台可以同 時運行多個操作系統,將一個系統平台虛擬為多個系統。 [Disabled] 關閉此功能。 Hardware Prefetcher [Enabled] [Enabled] 本項目可以讓硬件平台獨立和同步運行多重操作系統。 [Disabled] 關閉此功能。 Adjacent Cache Line Prefetch [Enabled] [Enabled] 本項目可以讓硬件平台運行 Adjacent Cache Line Prefetch 功能。 [Disabled] 關閉此功能。 Boot Performance Mode [Max Performance] 本項目用來讓您在操作系統切換前選擇 BIOS 設置的性能狀態。設置值有:[Max Non-Turbo Performance] [Max Battery] [Turbo Performance]。 Maximum CPU Core T
CPU Power Management Configuration 本項目用來管理與設置處理器電力。 Enhanced Intel SpeedStep Technology [Enabled] 本項目可以讓操作系統動態調整處理器電壓與核心頻率,藉以降低平均能耗以 及減少平均熱能。 [Disabled] 處理器會以默認速度運行。 [Enabled] 處理器的速度則由操作系統控制。 Turbo Mode [Enabled] 本項目用來設置核心處理器的速度,使其在運行電力、電流與溫度條件限制 下,可以比基本運行頻率更快的速度運行。設置值有:[Enabled] [Disabled]。 CPU C-states [Auto] 本項目用來設置 C P U s t a t e s 的電源節能。設置值有:[A u t o] [D i s a b l e d] [Enabled]。 以下項目只有在 CPU C-states 設置為 [Enabled] 時才會出現。 Enhanced C1 state [Enabled] 本項目可以讓處理器在閒置時降低電力消耗。設置值有:[E n a b l e d] [Disab
3.6.2 PCH 設置(PCH Configuration) PCI Express Configuration 本項目用來管理與設置 PCI Express 插槽。 PCIe Speed [Auto] 本項目用來讓系統自動選擇 PCI Express 連接端口速度。設置為 [Gen1] 時, PCI-E 連接端口會以 PCI-E 1.0 速度運行。設置為 [Gen2] 時,PCI-E 連接端口會 以 PCI-E 2.
3.6.3 PCH 存儲設備設置(PCH Storage Configuration) 當您進入 BIOS 設置程序時,BIOS 設置程序將自動檢測已安裝的 SATA 設備。當 未偵側到 SATA 設備時將顯示 Not Present。 SATAExpress_1 SRIS Support [Auto] [Auto] 系統將自動調整 SRIS(Separate Reference Clock Independent Spread Spectrum Clocking Architecture)以支持連接 SATA Express 設備。 [Disabled] 選擇本項目來使用 ASUS RUNWAY SATA Express 橋接連接卡。 S.M.A.R.T. Status Check [On] S.M.A.R.T.
SATA Controller 1 Mode Selection [AHCI] 本項目可設置 SATA 硬件設備的相關設置。 [Disabled] 關閉 SATA 功能。 [IDE] 若要將 Serial ATA 作為 Parallel ATA 物理保存接口,請將本項目設 置為 [IDE]。 [AHCI] 若要 Serial ATA 硬件設備使用 Advanced Host Controller Interface (AHCI) 模式,請將本項目設置為 [AHCI]。AHCI 模式可讓內置的存 儲設備啟動高級的 Serial ATA 功能,通過原生命令排序技術來提升 工作性能。 [RAID] 若要在 Serial ATA 硬盤設置 RAID 磁盤陣列,請將本項目設置為 [RAID]。 以下項目只有在 SATA Controller 1 Mode Selection 設置為 [IDE] 時才會 出現。 SATA6G_1-2 [beige], SATA6G_3-6 [gray] 本項目顯示所有連接至 SATA6G 連接端口的設備,若是有些連接端口沒有使 用,則顯示為 [Not Installed]
3.6.4 系統代理設置(System Agent Configuration) DMI Configuration 本項目用來設置 DMI(直接媒體接口)以 PCI-E 2.
以下項目只有在 Intel VT for Directed I/O (VT-d) 設置為 [Enabled] 時才 會出現。 Interrupt Remmapping [Enabled] 本項目用來啟動或關閉支持 V T-D 中斷重新指派功能。設置值有: [Enabled] [Disabled]。 Coherency Support (Non-Isoch) [Enabled] 本項目用來啟動或關閉支持 N o n-I s o c h V T-D 引擎一致性功能。設置值 有:[Enabled] [Disabled]。 Coherency Support (Isoch) [Enabled] 本項目用來啟動或關閉支持 I s o c h V T-D 引擎一致性功能。設置值有: [Enabled] [Disabled]。 第三章 3-42 第三章:BIOS 程序設置
3.6.5 USB 設備設置(USB Configuration) 本菜單可讓您更改 USB 設備的各項相關設置。 在 USB Devices 項目中會顯示自動檢測到的數值或設備。若無連接任何 設備,則會顯示 None。 [Auto] 當操作系統安裝有 xHCI 驅動程序,xHCI 會自動啟動並以 USB 3.0 模式運行。 [Smart Auto] xHCI 驅動程序在系統自我檢測(POST)過程中與操作系統中都支持 USB 3.0 模式。 [Enabled] 啟動 xHCI 控制器。 [Disabled] 關閉 xHCI 控制器。 xHCI Legacy USB Support [Enabled] [Enabled] 啟動在常規操作系統中支持 USB 3.0 設備功能。 [Disabled] USB 3.0 設備只能在 BIOS 程序設置中使用,無法在啟動設備列表中 被檢測到。 [Auto] 系統可以在啟動時便自動檢測是否有 USB 3.
xHCI Hand-off [Disabled] [Enabled] 啟動支持沒有 xHCI hand-off 功能的操作系統。 [Disabled] 關閉本功能。 EHCI Hand-off [Disabled] [Enabled] 啟動支持沒有 EHCI hand-off 功能的操作系統。 [Disabled] 關閉本功能。 USB Single Port Control 本項目用來啟動或關閉個別 USB 連接端口。 USB 連接端口的位置請參考 1.2.
3.6.
3.6.
PCI-EX4_1 Slot (black) Bandwidth [Auto] [Auto] PCIEX4_1 與 PCIEX1_1 插槽啟動時會以 AUTO 模式運行。 [X1 mode] PCIEX4_1 插槽關閉而 PCIEX1_1 插槽啟動時會以 X1 模式運行。 [X4 mode] PCIEX4_1 與 PCIEX1_1 插槽關閉時會以 X2 模式運行以獲得最佳性 能。 PCI-EX16_3 Slot (black) Bandwidth [X4 Mode] [X4 Mode] 以 X4 模式運行可以獲得系統資源彈性,M.2 插槽會以 X4 模式運 行。 [X8 Mode] 以 X8 模式運行可以獲得更高性能,而 M.2 插槽為關閉。 設置 PCIEX16_3 插槽帶寬為 X8 模式在 3-WAY 設置獲得更高的性能。 ASMedia USB 3.1 Controller [Enabled] 本項目用來啟動或關閉系統的 ASMedia® USB 3.1 控制器。設置值有:[Disabled] [Enabled]。 以下項目只有在 ASMedia USB 3.
Intel LAN Controller [Enabled] 本項目用來啟動或關閉 Intel 網絡控制器。設置值有:[Disabled] [Enabled]。 以下選項只有在 Intel LAN Controller 設置為 [Enabled] 時才會出現。 Intel Lan PXE OPROM [Disabled] 本項目可讓您開啟或關閉 Intel 網絡控制器的 PXE OptionRom。設置值有: [Enabled] [Disabled]。 Realtek LAN Controller [Enabled] 本項目用來啟動或關閉 Realtek 網絡控制器。設置值有:[Disabled] [Enabled]。 以下選項只有在 Realtek LAN Controller 設置為 [Enabled] 時才會出現。 Realtek PXE OPROM [Disabled] 本項目可讓您開啟或關閉 Realtek 網絡控制器的 PXE OptionRom。設置值有: [Enabled] [Disabled]。 Serial Port Configuration 本項目用來設置串口參數。 本項目只有
3.6.
3.6.9 網絡協定堆棧(Network Stack) Network Stack [Disable] 本項目用來啟動或關閉 UEFI 網絡協定堆棧(network stack)功能。設置值有: [Disable] [Enable]。 以下選項只有在 Network Stack 設置為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support [Enabled] 本項目用來啟動或關閉 I p v4/I p v6 P X E 啟動選項。設置值有:[D i s a b l e d] [Enabled]。 3.6.
3.7 監控菜單(Monitor menu) 監控菜單可讓您查看系統溫度/電力狀態,並可用來更改風扇設置。 往下滾動來顯示其他 BIOS 項目。 本系列主板具備溫度探測器,可自動檢測並顯示當前處理器與熱敏雷達的溫度。若 是您不想顯示檢測的溫度,請選擇 [Ignore]。 CPU Core Voltage, 3.
CPU Q-Fan Control [Auto] 本項目用來設置 CPU Q-Fan 運行模式。 [Auto] 檢測安裝的處理器風扇類型並自動切換控制模式。 [PWM Mode] 在 PWM 模式啟動 CPU Q-Fan 控制來使用 4-pin 處理器風扇。 [DC Mode] 當安裝 3-pin 的處理器風扇時,請選擇本項目來使用 Q-Fan 控 制的 DC 模式。 [Disabled] 關閉 CPU Q-Fan 控制功能。 以下的項目只有在 CPU Q-Fan Control 設為 [Auto]、[PWM Mode] 與 [DC Mode] 時才會出現。 CPU Fan Speed Low Limit [300 RPM] 本項目可以讓您設置 CPU Q-Fan Control 的功能及處理器風扇速度。設置值 有:[Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]。 CPU Fan Profile [Standard] 本項目用來設置處理器風扇適當的性能。 [Standard] 設置為 [Standard]
Chassis Fan 1/4 Q-Fan Control [DC Mode] 這些項目用來設置主板機箱風扇的 Q-Fan control 為 DC 模式、PWM 模式或關閉 Q-Fan controls 功能。設置值有:[Disabled] [DC Mode] [PWM Mode]。 以下項目只有在 Chassis Fan 1/4 Q-Fan Control 設置為 [PWM Mode] 或 [DC Mode] 時才會出現。 Chassis Fan 1/4 Q-Fan Source [DC Mode] 本項目用來根據選擇的溫度來源控制指派的風扇。設置值有:[C P U] [M B] [VRM] [PCH Core] [T_SENSOR1] [EXT_SENSOR1] [EXT_SENSOR2] [EXT_ SENSOR3]。 若選擇 T_SENSOR1,請將熱敏電阻排線插在 T_SENSOR1 接口,並將 熱敏電阻排線接口貼在溫度來源的元件上。 Chassis Fan 1/4 Speed Low Limit [300 RPM] 本項目用來關閉或設置機箱風扇警告轉度。設置值有:[I g n o r e]
Chassis Fan 1/4 Min.
ASST Fan 1/5 Lower Temperature [40] 使用 <+> 與 <-> 鍵調整機箱風扇溫度的最小值。數值可能會隨著 Q-Fan 調整而異。 ASST Fan 1/5 Min.
3.
Network Stack Driver Support [Disabled] [Disabled] 在 POST 時略過載入網絡協定堆棧驅動器。 [Enabled] 在 POST 時載入網絡協定堆棧驅動器。 Next Boot after AC Power Loss [Normal Boot] [Normal Boot] 電源中斷後,在下一次啟動時恢復至正常啟動速度。 [Fast Boot] 電源中斷後,在下一次啟動時加快啟動速度。 DirectKey (DRCT) [Enabled] [Disabled] 關閉 DirectKey 按鈕功能,當按下 DirectKey 按鈕時系統僅會啟動或 關機。 [Enabled] 當按下 DirectKey 按鈕時系統會啟動並直接進入 BIOS。 Boot Logo Display [Auto] [Auto] 設置在啟動自我檢測(POST)過程中的啟動畫面。 [Full Screen] 設置在啟動自我檢測(POST)過程中的啟動畫面為全屏。 [Disabled] 關閉全屏個人化啟動畫面功能。 以下項目只有在 Boot Logo Displ
Option ROM Messages [Force BIOS] [Force BIOS] 選購設備固件信息會在啟動自我檢測時顯示。 [Keep Current] 在啟動自我檢測時關閉選購設備固件信息並只顯示華碩啟動圖標。 INT19 Trap Response [Immediate] [Immediate] 立即運行 trap of INT19。 [Postponed] 在常規啟動程序運行 trap of INT19。 Above 4G Decoding [Disabled] 本項目用來讓您在 4G 地址空間上解碼 64 位設備。設置值有:[D i s a b l e d] [Enabled]。 Setup Mode [EZ Mode] [Advanced Mode] 將 Advanced Mode 設置為 BIOS 設置程序的默認值。 [EZ Mode] 將 EZ Mode 設置為 BIOS 設置程序的默認值。 CSM (兼容性支持模塊) 本項目用來設置 CSM(兼容性支持模塊)項目來完全支持各種 VGA、啟動設備和 附加設備,藉以獲得更佳的兼容性。 Launch CSM [Au
Boot from Storage Devices [Legacy OpROM first] 本項目用來選擇想要運行的存儲設備類型。設置值有:[B o t h, L e g a c y OpROM first] [Both, UEFI first] [Legacy OpROM first] [UEFI driver first] [Ignore]。 Boot from PCIe/PCI Expansion Devices [Legacy OpROM first] 本項目用來選擇想要運行的 PCIe/PCI 擴展設備類型。設置值有:[Legacy OpROM first] [UEFI driver first]。 Secure Boot 本項目用來設置 Windows® 安全啟動的相關參數以及管理系統金鑰,以提升系統在 啟動自我檢測(POST)時的安全性,避免受到未授權的用戶與惡意軟件的危害。 OS Type [Windows UEFI mode] [Windows UEFI Mode] 本 項 目 用 來 選 擇 安 裝 的 操 作 系 統 。 運 行 Microsoft ® 安全啟動檢查。只有在 Wi
KEK Management KEK(金鑰交換金鑰 [Key-exchange Key] 或金鑰註冊金鑰 [Key-Enrollment Key])用來管理簽名數據庫(db)與撤銷簽名數據庫(dbx)。 Key-exchange Key(KEK)指的是 Microsoft ® Secure Boot KeyEnrollment Key(KEK)。 Delete the KEK 本項目用來刪除系統中的 KEK。設置值有:[Yes] [No]。 Load KEK from File 本項目用來由 USB 存儲設備載入已下載 KEK。 Append Var to KEK 本項目用來由存儲設備載入附加的 KEK,以管理附加的簽名數據庫(db) 與撤銷簽名數據庫(dbx)。 KEK 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 DB Management db(認證簽名數據庫)列出可以在單一電腦載入之 UEFI 應用程序、操作系統 載入器與 UEFI 驅動程序的簽名者或圖片圖像。 Delete the db 本項目用來刪除系統中的 db 文件。設置值有:[Yes] [No]。 Load db from
DBX Management dbx(撤銷簽名數據庫)列出 db 項目中不再被信任且無法被載入之被禁止的 圖片圖像。 Delete the dbx 本項目用來刪除系統中的 dbx 文件。 Load dbx from File 本項目用來由 USB 存儲設備載入已下載的撤銷簽名數據庫(dbx)。設置 值有:[Yes] [No]。 Append dbx from File 本項目用來由存儲設備載入附加的撤銷簽名數據庫(d b x),以使更多的 db 圖片圖像無法被載入。 dbx 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 Boot Option Priorities 本項目讓您自行選擇啟動磁盤並排列啟動設備順序。依照 1st、2nd、3rd 順序分 別代表其啟動設備順序,而設備的名稱將因使用的硬件設備不同而有所差異。 • 欲進入 Windows 安全模式時,請在啟動自我檢測(POST)時按下 (Windows 8 不支持這項功能)。 • 啟動時您可以在 ASUS Logo 出現時按下 選擇啟動設備。 Boot Override 第三章 本項目將顯示可使用的設備,設備的名
3.9 工具菜單(Tools menu) 本工具菜單可以讓您針對特別功能進行設置。請選擇菜單中的選項並按下 鍵來顯示子菜單。 GPU Post 本項目顯示安裝在本主板的顯卡,並顯示建議安裝的顯卡數量讓您獲得最佳性能。 3.9.1 ASUS EZ Flash 2 第三章 本項目可以讓您啟動華碩 EZ Flash 2 程序,按下 會出現再次確認的窗 口,請使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 3.11.
3.9.2 ASUS O.C.
3.9.
3.10 退出 BIOS 程序(Exit menu) 本菜單可讓您讀取 BIOS 程序出廠默認值與退出 BIOS 程序,並可保存與取消對 BIOS 項目的更改。你也可以由 Exit 菜單進入 EZ Mode。 Load Optimized Defaults 本項目可讓您載入 BIOS 程序設置菜單中每個參數的默認值。當您選擇本項目或按 下 ,便會出現一個確認對話窗口,選擇 Yes 以載入默認值。 Save Changes & Reset Discard Changes & Exit 本項目可讓您放棄所做的更改,並恢復原先保存的設置。在選擇本項目或按下 鍵後,將會出現一個確認對話窗口,請選擇 Yes 以放棄任何設置並載入原先保 存的設置,同時退出 BIOS 設置程序。 Launch UEFI Shell from USB devices 本項目可以讓您由含有數據系統的設備中啟動 UEFI Shell(shellx64.
3.11 更新 BIOS 程序 華碩網站上提供有最新的 B I O S 程序,可以強化系統的穩定度、兼容性或運行性 能,但是運行 BIOS 程序更新是具有潛在性風險的,若是使用現有版本的 BIOS 程序 都沒有發生問題時,請勿手動運行更新 BIOS 程序。不適當的 BIOS 程序更新可能會 導致系統啟動失敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程序。 請訪問華碩網站(http://www.asus.com.cn)來下載本主板最新的 BIOS 程序。 1. EZ Update:在 Windows 操作系統中更新 BIOS 程序。 2. ASUS EZ Flash 2:使用 U 盤來更新 BIOS。 3. ASUS CrashFree BIOS 3:當 BIOS 文件遺失或損毀時,可以使用 U 盤或主板的 驅動程序與應用程序光盤來更新 BIOS。 4. ASUS BIOS Updater:在 DOS 環境下,使用主板驅動程序與應用程序光盤與 U 盤來更新並備份 BIOS。 上述軟件請參考相關章節的詳細使用說明。 3.11.
3.11.2 華碩 EZ Flash 2 華碩 EZ Flash 2 程序讓您能輕鬆的更新 BIOS 程序,可以不必再通過啟動盤的冗 長程序或是到 DOS 模式下運行。 請至華碩網站 http://www.asus.com.cn 下載最新的 BIOS 程序文件。 請依照以下步驟通過 EZ Flash 2 更新 BIOS 程序: 1. 將保存有最新的 BIOS 文件的 U 盤插入 USB 連接端口。 第三章 2. 進入 BIOS 設置程序的 Advanced Mode,選擇 Tool > ASUS EZ Flash Utility, 接著請按下 鍵。 3. 請使用 鍵操控 Drive 區域。 4. 請利用上/下方向鍵找到存放有最新 B I O S 文件的 U 盤,接著請按下 鍵。 5. 請使用 鍵操控 Folder Info 區域。 6.
3.11.3 華碩 CrashFree BIOS 3 華碩最新自行研發的 CrashFree BIOS 3 工具程序,讓您在當 BIOS 程序和數據被 病毒入侵或丟失時,可以輕鬆的從驅動程序及應用程序光盤,或是從含有最新或原始 的 BIOS 文件的 U 盤中恢復 BIOS 程序的數據。 在驅動程序及應用程序光盤中的 BIOS 程序版本可能會比官方網站上的 BIOS 程序版本舊,若是想要使用更新的 BIOS 程序,請至 http://www. asus.com.cn/support/ 網站下載,並保存在便攜存儲設備中。 恢復 BIOS 程序 請依照下列步驟使用應用程序光盤恢復 BIOS 程序: 1. 啟動系統。 2. 將主板的應用程序光盤放入光驅,或是將含有最新或原始的 BIOS 文件的 U 盤插 入 USB 連接端口。 3. 接著工具程序便會自動檢查光盤或存儲設備中是否存有 B I O S 文件。當搜索到 BIOS 文件後,工具程序會開始讀取 BIOS 文件並自動進入 ASUS EZ Flash 2 程 序。 4.
3.11.4 華碩 BIOS Updater 華碩 BIOS Updater 讓您可以在 DOS 環境下更新 BIOS 程序,還可以用來複製現 有的 BIOS 文件,當您的 BIOS 程序在更新過程中失敗或中斷時,可以作為備份使 用。 以下的程序畫面只能參考,您實際操作的畫面可能會與手冊所示的畫面 不盡相同。 更新 BIOS 之前 1. 準備本主板的驅動程序與應用程序光盤,以及 USB 存儲設備。 2. 訪問華碩網站 http://www.asus.com.cn/support/ 下載最新的 BIOS 程序與 BIOS Updater,然後保存在 USB 存儲設備。 F r e e D O S 環境下不支持 N T F S 格式,請確認 U S B 存儲設備為 FAT32/16 格式且單一磁區的格式。 3. 將電腦關機。 4. 請確認電腦配備有光驅。 DOS 環境下啟動系統 1. 將存有最新 BIOS 文件與 BIOS Updater 的 USB 存儲設備插入 USB 連接端口。 2.
4. 當啟動信息出現時,在五秒鐘內按下 鍵來進入 FreeDOS 彈出窗口。 ISOLINUX 3.20 2006-08-26 Copyright (C) 1994-2005 H. Peter Anvin A Bootable DVD/CD is detected. Press ENTER to boot from the DVD/CD. If no key is pressed within 5 seconds, the system will boot next priority device automatically. boot: 5. 當 FreeDOS 出現時,輸入命令 d:,然後按下 ,將磁盤 C(光驅)改為磁 盤 D(USB 存儲設備)。 Welcome to FreeDOS (http://www.freedos.org)! C:/> d: D:/> 更新 BIOS 文件 請依照以下步驟更新 BIOS 文件: 1.
4. BIOS Updater 檢查所選的 BIOS 文件後,選擇 Yes 來確認 BIOS 更新。 Are you sure you want to update the BIOS? Yes No 由於安全規則,不支持 BIOS 備份功能。 5. 選擇 Yes 然後按下 ,當 BIOS 更新完成時,按下 退出 BIOS Updater。 6. 重新啟動電腦。 請勿在 BIOS 進行更新時,運行關機或重新啟動電腦,以防止 BIOS 更新 失敗。 第三章 請載入 BIOS 程序的默認值以確保系統的兼容性與穩定度。在 3.
第三章 3-72 第三章:BIOS 程序設置
第四章 4.1 安裝操作系統 • 本主板支持 Microsoft ® 32-bit/64-bit Windows ® 7、32-bit/64bit Windows ® 8、32-bit/64-bit Windows ® 8.1 操作系統(OS, Operating System)。 • 由於主板和周邊硬件設備的選項設置繁多,本章僅就軟件的安裝程序 供您參考。您也可以參閱您使用的操作系統說明文件以取得更詳盡的 信息。 4.2 驅動程序及應用程序 DVD 光盤信息 隨貨附贈的驅動程序及應用程序 DVD 光盤包括了數個有用的軟件和應用程序,將 它們安裝到系統中可以強化主板的性能。 華碩驅動程序及應用程序 D V D 光盤的內容會不定時地更新,但不另行 通知。如欲得知最新的信息,請訪問華碩的網站 http://www.asus.com. cn。 4.2.1 運行驅動程序及應用程序 DVD 光盤 當您在 Windows 7、Windows 8 或 Windows 8.1 操作系統中運行驅動 程序及應用程序 DVD 光盤之前,請先確認您擁有管理員帳號。 請依照以下步驟運行驅動程序及應用程序 DVD 光盤: 1.
驅動程序及應用程序 DVD 光盤 驅動程序菜單顯示系統檢 測到連接設備可使用的驅 動程序,請安裝適當的驅 動程序來使用該設備 軟件菜單顯示 本主板支持的 應用程序與其 他軟件 取得 RAID/AHCI 驅動程序 手冊菜單顯示本光盤 所附的用戶手冊,點 擊想要的項目來開啟 用戶手冊的文件夾 點擊聯絡信 息標籤頁顯 示與華碩聯 絡的信息 點擊圖標顯 示 DVD/主 板信息 點擊安裝各 項驅動程序 第四章 4-2 第四章:軟件支持
4.2.2 取得軟件用戶手冊 您可在驅動程序 DVD 光盤中找到軟件用戶手冊,請依照以下步驟來取得您需要的 軟件用戶手冊。 軟件用戶手冊文件為 P D F 格式,在您開啟用戶手冊文件前,請先安裝 Adobe® Acrobat® Reader 瀏覽軟件。 1. 點擊 M a n u a l(用戶手冊) 標 籤頁,由列表中選擇 A S U S Motherboard Utility Guide。 2. 進入 Manual(用戶手冊) 文件 夾後,在您需要的用戶手冊文件 夾用鼠標左鍵點二下。 第四章 3.
4.3 軟件信息 驅動程序及應用程序光盤中大部分的應用程序都會有安裝指導向導來協助您一步一 步輕鬆地安裝軟件。您也可以由個別軟件所提供的在線說明文件或讀我文件取得安裝 方式及其他信息的說明。 4.4 華碩 AI Suite 3 程序 通過友善的用戶界面,華碩 AI Suite 3 程序將所有的華碩獨家功能集成在一個軟件 套件中,可以同時操控並運行各項功能及應用程序。 安裝華碩 AI Suite 3 程序 在您將 AI Suite 3 程序安裝至 Windows 7、Windows 8 或 Windows 8.1 操作系統之前,請先確認您擁有管理員帳號。 請依照下列步驟將華碩 AI Suite 3 程序安裝到您的電腦: Windows 7 操作系統 1. 將驅動程序及應用程序 DVD 光盤放入光驅。 2. 在自動播放(AutoPlay)對話框中點擊運行 ASSETUP.exe。 3.
Windows 8 與 Windows 8.1 操作系統 1. 將驅動程序及應用程序 DVD 光盤放入光驅,然後依照屏幕的指示來完成安裝步 驟。 2. 從驅動程序及應用程序 DVD 光盤主菜單中選擇應用程序(Utilites)標籤頁,然 後點擊 AI Suite 3。 3. 請依照屏幕的指示運行。 若是驅動程序及應用程序 DVD 光盤主菜單沒有出現,請參考以下步驟: a. 到 開始 畫面,然後點擊或輕觸桌面的應用程序。 b. 在桌面的左下角點擊或輕觸 File Explorer 觸或雙擊 設置。 ,然後選擇 DVD 磁盤並輕 運行華碩 AI Suite 3 程序 Windows 7 操作系統 從桌面點擊 開始 > 所有應用程序 > ASUS > AI Suite 3> AI Suite 3。 您也可以在 Windows 7 的通知任務欄中點擊 。 Windows 8 與 Windows 8.
AI Suite 3 主畫面 AI Suite 3 主畫面提供您輕鬆進入控制和了解電腦發生了什麼狀況 - 能提供您將性 能做最佳化設置,並同時確保系統的穩定性。 AI Suite 主畫面包含一個快速進入的主菜單工具列,可以讓您快速開啟任何集中在 這裡的華碩應用程序。點擊主畫面右上方 圖標便可以開啟此主菜單工具列。 點擊以啟動 AI Suite 3 菜單工具列 AI Suite 3 主畫面只能參考,請以您實際看到的畫面為準。 AI Suite 3 主菜單工具列 Thermal Radar 2 Ai Charger+ 第四章 USB 3.1 Boost EZ Update 系統信息 USB BIOS Flashback 推播信息 USB Charger+ 版本 • 本章節的畫面只能參考,請以您實際看到的畫面為準。 • 請參考驅動程序 D V D 光盤中軟件手冊的說明,或訪問華碩網站 http://www.asus.com.
Thermal Radar 2(熱敏雷達 2)程序 Thermal Radar 2(熱敏雷達 2)讓您可以實時控制風扇、監控顯卡與其他元件的 溫度,或自動調整溫度設置。 Thermal Tuning(熱敏調校) 這個功能會依照系統現在的溫度設置,自動為系統提供最佳化冷卻解決方案。可以 讓您設置處理器、機箱與獨家 TUF 渦輪風扇來獲得冷卻性能與低噪音之間的平衡。 點擊以自動開始進 行熱敏調校操作 Thermal Status(熱敏狀態) 顯示系統現在的溫度狀況。 第四章 點擊以評估現 在的溫度設置 華碩 SABERTOOTH X99 主板用戶手冊 4-7
Recorder(記錄) 顯示與監控溫度設置的狀況與系統狀態。 點擊以上 下滾動 Fan Control(風扇控制) 本項目用設置安裝在系統中的風扇,您也可以載入或保存風扇設置文件來調整系統 的溫度狀況。 點擊以載入已保存的設置文件 點擊以在項 目間切換 點擊以保存為 新的設置文件 風扇超時設置 第四章 4-8 第四章:軟件支持 Dust de-Fan 設置
DIGI+ Power Control 程序 華碩 DIGI+ Power Control 電源控制擁有革命性與創新的數字 VRM 與 DRAM 內 存電壓控制器。這些控制器提供極度精確的內存與電壓調整,帶給您最佳的效率、穩 定性與系統性能。 點擊以進入處 理器設置畫面 點擊以進入內 存設置畫面 DIGI+ Power Control - CPU 點擊回到上 一個畫面 點擊以在項 目間切換 點擊以取消更改 點擊以應 用更改 點擊以取消更改 點擊以應 用更改 第四章 DIGI+ Power Control - DRAM 點擊回到上 一個畫面 華碩 SABERTOOTH X99 主板用戶手冊 4-9
4.4.1 Ai Charger+ 這個程序可以對連接在 USB 連接端口上的便攜 BC 1.1* 行動設備進行快速充電, 並且充電速度較標準 USB 設備快三倍**。 運行 Ai Charger+ 若要運行 Ai Charger+,請點擊屏幕右上方 單工具列上的 Ai Charger+。 圖標,然後點擊 AI Suite 3 主菜 只有某些型號的主板有 Ai Charger+ 功能。 Ai Charger+ 主畫面 勾選以啟動或關閉 Ai Charger+ 點擊以應用 • *請確認您的 USB 設備製造商是否完整支持或兼容 BC 1.
4.4.
手動更新 BIOS 與選擇啟動圖標 點擊以搜索您想使用的啟動圖標文件 X99 X99 X99 02 點擊以回到 EZ Update 主畫面 5 點擊以運行更新 BIOS 與啟動圖標 在您點擊 BIOS Update 按鈕後,點擊 Flash 開始更新 BIOS 與上傳啟動圖標文 件至您的系統。 X99 02 5 02 5 X99 第四章 4-12 第四章:軟件支持 X99
4.4.3 USB BIOS Flashback 向導 USB BIOS Flashback 向導可以查看並將最新版 BIOS 程序保存至 USB 存儲設備, 配合 ASUS USB BIOS Flashback 的硬件特色,讓您不需重新啟動即可更新 BIOS 程 序。 運行華碩 USB BIOS Flashback 程序 若要運行 USB BIOS Flashback,請點擊 AI Sutie 3 主菜單右上方的 然後選擇 USB BIOS Flashback。 圖標, USB BIOS Flashback 只適用於特定的主板型號。 使用 USB BIOS Flashback 程序 設置下載 BIOS 更新的排程 點擊以取消下 載的排程設置 點擊以應用下 載的排程設置 點擊以確認是否有 BIOS 固件更新可下載 設置下載 BIOS 更新的排程 1. 請於 Download Setting(下載設置) 中勾選 Schedule (days)(排程),並選擇 下次進行下載更新的天數。 第四章 2.
下載最新版 BIOS 下載前請先確認已經將支持 USB BIOS Flashback 的 USB 存儲設備連接 至電腦的 USB 連接端口。請參考 2.3.1 後側面板連接端口 一節的詳細說 明。 請依照以下步驟下載最新版 BIOS: 1. 在 USB BIOS Flashback 主畫面中點 擊 Check for New BIOS Update 查 看是否有 BIOS 固件更新可下載。 請等待系統確認最新版的 BIOS 固件 版本。 2.
4.4.4 推播信息(Push Notice) 這個應用程序讓您可以將系統狀態的詳細信息傳送至智能型設備,您也可以使用這 個程序傳送信息至智能型設備。 使用這個應用程序之前,請先確認您的電腦與智能型設備已經完成配 對。請參考 配對電腦與智能型設備 一節的詳細信息。 啟動電腦的推播信息(Push Notice) 若要啟動推播信息,請點擊 AI Sutie 3 主菜單右上方的 Push Notice。 圖標,然後選擇 推播信息(Push Notice)主畫面 點擊以啟動或關閉推播信息(Push Notice) 勾選智能 型設備 點擊以放棄設置 點擊以應用設置 您也可以通過屏幕右上角的 P u s h N o t i c e 快捷方式來啟動推播信息功 能,請點擊 << 然後點擊 ,再選擇 。 配對電腦與智能型設備 請依照以下步驟配對電腦與智能型設備: 1. 在智能型設備點擊 來啟動推播信息(Push Notice)。 2.
設置要發出警告的模式 本功能用來設置當電腦重新啟動、關機或進入睡眠模式時,傳送警示信息至智能型 設備。 勾選這些項目來選擇 欲啟動警示的模式 勾選智能 型設備 設置日期與時 間來啟動模式 設置在模式啟動前 幾分鐘要傳送警示 輸入要傳送的信息 設置電腦狀態警示 本功能用來將電腦上不正常的狀態,如:電壓、溫度和風扇設置等信息傳送警示至 智能型設備。 勾選智能 型設備 勾選欲傳送至智 能型設備的項目 勾選本項目當元件恢復正常狀 態時傳送警示至智能型設備 第四章 4-16 第四章:軟件支持
傳送信息至智能型設備 本功能用來傳送信息至智能型設備。 您也可以通過屏幕右上角的推播信息(Push Notice)信息快捷方式來傳 送信息,請點擊 << 然後點擊 ,再選擇 。 勾選智能 型設備 點擊來傳 送信息 點擊來輸入信息 點擊來清除信息 欄中的所有文字 點擊來保存信息 在智能型設備查看電腦狀態 在智能型設備點擊 來啟動推播信息(Push Notice)。 Push Notice 點擊以查看 警示模式 點擊以刪 除警示 點擊以查看 警示狀態 點擊以查看傳 送過的信息 第四章 點擊以掃描 更多主機 華碩 SABERTOOTH X99 主板用戶手冊 4-17
4.4.5 華碩 USB 3.1 Boost 程序 華碩 USB 3.1 Boost 程序支持 USB 連接 SCSI 協議(UASP,USB Attached SCSI Protocol)。通過華碩 USB 3.1 Boost 程序,可輕鬆提升您的 USB 設備之傳輸速 度。 運行華碩 USB 3.1 Boost 程序 若要運行 USB 3.1 Boost,請點擊 AI Sutie 3 主菜單右上方的 選擇 USB 3.1 Boost。 圖標,然後 使用華碩 USB 3.1 Boost 程序 點擊以啟動 USB 設備 的正常數據傳輸率 點擊以選擇 USB 設備 點擊以啟動 UASP 或 Turbo 模式來獲得更快 的數據傳輸率 請將您的 USB 3.1/3.0 設備連接到支持 USB 3.1 Boost 的 USB 3.1/3.0 連接端口,請參考 2.3.1 後側面板連接端口 以了解更多說明。 • USB 3.1 Boost 程序會自動檢測支持 UASP 功能的 USB 3.1/3.0 設 備。 • 使用 USB 3.1/3.
4.4.
查看 SPD 信息 從系統信息主畫面,點擊 SPD 標籤頁來查看內存的相關信息。 第四章 4-20 第四章:軟件支持
4.4.7 USB Charger+ USB Charger+ 用來快速充電您的便攜 USB 設備,即使在電腦關機、睡眠狀態或 休眠狀態仍可進行充電。 在使用 USB Charger+ 之前,請先確認關閉在 BIOS 設置中 Advanced 模式的 Advanced > APM > ErP Ready 的 Erp Ready 選項。 運行 USB Charger+ 若要運行 USB Charger+,請點擊 AI Sutie 3 主菜單右上方的 擇 USB Charger+。 圖標,然後選 USB Charger+ 主畫面 點擊來檢測 已連接的 USB 設備 點擊以快速 充電您的 USB 設備 顯示連接的 USB 設備正處 於充電中模式 點擊以停止 充電您的 USB 設備 點擊以應 用設置 點擊您想要在系統關機時進 行充電的 USB 設備類型 點擊以取消 應用設置 請確認將您的 U S B 設備連接至支持本程序之 U S B 連接端口。請參考 2.3.
4.4.
4.
4.6 TUF Detective TUF Detective 可以讓您通過 Android 行動設備遠端管理與控制您的電腦,並提供 相關的系統信息。 請依照以下步驟使用 TUF Detective: 1. 使用傳輸線連接您的行動設備與 主板後側的 TUF Detective 連接 端口。 2. 在 行 動 設 備 下 載 與 安 裝 T U F Detective APP 程序。 您可以從 Play 商店下載 TUF Detective APP, 或是掃描 QR code 來 找到程序。 找到 TUF Detective APP,下載並安裝 至您的行動設備 3. 啟動 APP 來遠端管理與控制您 的電腦。 掃描 QR code 也可以找到程序 4.6.
4.6.
點擊 CLEAR CMOS 並 選擇 Yes 可以清除 CMOS RTC RAM 數據。 點擊 PATCH ERROR 並 選擇 Yes 自動修復您的電腦 。 4.6.
點擊三角形圖標來監控溫 度。 點擊三角形圖標來監控風 扇轉速。 4.6.
4.
選擇音頻輸出 Realtek HD Audio Manager 讓您依照使用的輸出設備來選擇音頻輸出類型。 請依照以下步驟選擇輸出音頻: 1. 將設備接口插入聲音輸出(草綠色)連接端口,若是設備接口已經插入至相對應 的連接端口,點擊 Realtek HD Audio Manager 中的 圖標。 a. 若 選 擇 耳 機 (Headphone),請點擊 安裝的耳機類型然後再點 擊 OK。 b. 若選擇 前置喇叭輸出 (Front Speaker Out), 請點擊安裝的喇叭類型然 後再點擊 OK。 第四章 2.
第四章 4-30 第四章:軟件支持
第五章 5.1 RAID 功能設置 本主板支持 Intel® Rapid Storage Technology,並支持建構 RAID 0、RAID 1、 RAID 10 和 RAID 5。 5.1.
5.1.2 安裝 Serial ATA(SATA)硬盤 本主板支持 Serial ATA 硬盤。為了最佳的性能表現,當您要創建陣列模式設置 時,請盡可能採用具備相同型號與容量的硬盤。 請依照以下安裝方式來建構 SATA RAID 磁盤陣列: 第五章 1. 將硬盤安裝至硬盤槽中。 2. 安裝硬盤連接排線,將欲建構磁盤陣列的硬盤連接至主板。 3. 將 SATA 電源線連接到每一部硬盤。 5.1.3 在 BIOS 程序中設置 RAID 在您開始創建陣列之前,您必須先在 BIOS 程序設置中設置對應的 RAID 選項。請 依照下列步驟進行操作︰ 1. 在啟動之後系統仍在內存的啟動自我測試(Power-On Self Test,POST)時,按 下 按鍵進入 BIOS 設置程序。 2. 進入主菜單(Main)後,選擇 Advanced > SATA Configuration 選項,然後按 。 3. 將 SATA Mode 選項設置為 [RAID Mode]。 4.
5.1.4 進入 Intel® Rapid Storage Technology Option ROM 應用程序 請依照下列步驟來進入 Intel® Rapid Storage Technology Option ROM 應用程序: 2. 當系統運行啟動自我檢測(POST)時,按下 按鍵來進入應用程序主菜 單。 Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID RAID Volumes: None defined. Physical Devices: Port Device Model 0 ST3160812AS 1 ST3160812AS 2 ST3160812AS 3 ST3160812AS [↑↓]-Select MENU ] 4.
創建 RAID 設置 請依照下列步驟創建 RAID 設置: 1. 選擇 1. Create RAID Volume 然後按下 按鍵,會出現如下圖所示的窗口 畫面。 第五章 Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: Disks: Strip Size: Capacity: Sync: Create volume [ HELP ] Enter a unique volume name that has no special characters and is 16 characters or less. [↑↓]-Select [ESC]-Exit [ENTER]-Select Menu 2. 為您的 RAID 磁區鍵入一個名稱,然後按下 按鍵。 3.
6. 使用向上、向下方向鍵來選擇 RAID 磁盤陣列(RAID 0、RAID 10、RAID 5)要 分區的容量,然後按下 按鍵。分區的數值可由 4KB 遞增至 128KB,數 據分區的數值應該以硬盤使用的目的來決定。下列為推荐: RAID 0: 128KB RAID 10: 64KB RAID 5: 64KB 若此系統欲作為服務器使用,建議您選擇較低的磁區大小;若此系統欲 作為多媒體電腦用來運行影音的編輯製作,建議您選擇較高的磁區大小 來獲得最佳的性能。 7. 輸入您所要的陣列容量,接著按下 按鍵。本項目默認值是採用最高可容 許的磁盤容量。 8. 在 Create Volume 的提示對話框中再按下 按鍵來創建磁盤陣列,接著便 會出現如下圖的窗口畫面。 WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 9.
刪除 RAID 陣列 當您要刪除 RAID 設置時請小心,保存在硬盤中的數據會被全部刪除。 第五章 請依照以下步驟刪除 RAID 陣列: 1. 選擇 2. Delete RAID Volume 然後按下 按鍵,會出現如下圖所示的窗口 畫面。 Name Volume0 [ DELETE VOLUME MENU ] Level Drives RAID0(Stripe) 2 Capacity 298.0GB Status Normal Bootable Yes [ HELP ] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED. (This does not apply to Recovery volumes) [↑↓]-Select [ESC]-Previous Menu [DEL]-Delete Volume 2.
5.2 在安裝 Windows® 操作系統時安裝 RAID 驅動程序 請依照下列步驟在 Windows® 操作系統中安裝 RAID 驅動程序: 2. 將搭載有 RAID 驅動程序的光盤/ U 盤安裝光驅/ USB 連接端口,並點擊 Browse (瀏覽)。 3. 請選擇您的設備後,選擇 Drivers > RAID,然後選擇 RAID 驅動程序文件,再按 下 OK。 4. 請依照屏幕指示來完成驅動程序的安裝。 在從 U 盤載入 RAID 驅動程序之前,您必須使用另一台電腦來將應用程 序光盤中的 RAID 驅動程序複製到 U 盤。 要在 RAID 模式下設置 Windows ® UEFI 操作系統,請先為光驅載入 UEFI 驅動程序。 華碩 SABERTOOTH X99 主板用戶手冊 5-7 第五章 1.
第五章 5-8 第五章:RAID 支持
附錄 華碩的聯絡信息 華碩電腦(上海)有限公司 ASUSTEK COMPUTER (SHANGHAI) CO., LTD 市場信息 技術支持 地址: 上海市閔行莘庄工業區春東路508號 電話:+86-21-54421616 傳真:+86-21-54420099 互聯網:http://www.asus.com.cn/ 電話: 400-620-6655 電子郵件: http://vip.asus.com.cn/VIP2/ Services/QuestionForm/ TechQuery 在線支持: http://www.asus.com.cn/support 華碩電腦公司 ASUSTeK COMPUTER INC.(亞太地區) 市場信息 技術支持 地址: 台灣臺北市北投區立德路15號 電話:+886-2-2894-3447 傳真:+886-2-2890-7798 電子郵件:info@asus.com.tw 互聯網:http://www.asus.com.tw 電話:+86-21-38429911 傳真: +86-21-58668722, ext.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Date : Signature : Representative Person' s Name : Feb. 26. 2015 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.