User Guide

ManualsBrandsASUS ManualsOthersw1

DISASSEMBLY PROCEDURE

2 - 1

Chapter

SW1 Disassembly

Procedure

Please follow the information provided in this section to perform

the complete disassembly procedure of the notebook. Be sure

to use proper tools described before.

W1 Series Notebook consists of various modules. This chapter describes the

procedures for the complete notebook disassembly. In addition, in between

procedures, the detailed disassembly procedure of individual modules will be

provided for your service needs.

The disassembly procedure consists of the following steps:

• Battery Module

• Keyboard Module

• LCD Module

• ODD Module

• HDD Module

• CPU Module

• Memory Module

• Top Cover Module

• Main Board Module

PDF created with pdfFactory Pro trial version www.pdffactory.com

Summary of content (11 pages)

PAGE 1
D I S A S S E M B L Y 2 P R O C E D U R E Chapter SW1 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. S W1 Series Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs.
PAGE 2
D I S A S S E M B L Y B A T T E R Y P R O C E D U R E Battery module The illustration below shows how to remove the Battery Module. Turn the notebook over, unlock latches and remove the Battery pack from bottom side of the notebook. K / B M O D U L E . Keyboard Module The illustration below shows how to remove the K/B cover and Keyboard Plate. K / B C O V E R R E M O V A L K / B R E M O V A L Removing K/B Cover 1. Unclench K/B Cover at red loop in the chart and drive up it. Removing K/B 1.
PAGE 3
D I S A S S E M B L Y P R O C E D U R E 2 L C D LCD module The illustrations below show how to remove and disassemble the LCD Module. The module contains LCD Panel, Inverter Board, LCD Hinge Bracket, Hinge Cover, LCD Bezel and LCD Cover. L C D R E M O V A L Removing LCD Module 1 1. 2. 3. 4. 5. 6. Release 4pcs screw on Base Door. Pull out Antenna Conn. Release 2pcs screw on rear Base Cover. Release 2pcs screw on side Base Cover. Release the screw of LCD ground cable.
PAGE 4
D I S A S S E M B L Y P R O C E D U R E 2 3 4 5 6 L C D D I S -A S S E M B L Y Disassembling LCD Module 1. Remove 6pcs rubber pads and release 6pcs screws from the LCD Module 2. Open inside four edges of LCD Bezel with your finger, and then remove LCD Bezel from LCD Module. 3. Remove Hinge Cover L & R. 4. Release 4pcs screws from LCD Panel and LCD Cover. 5. Disconnect left and right cable on the Inverter board. 2-4 PDF created with pdfFactory Pro trial version www.pdffactory.
PAGE 5
D I S A S S E M B L Y P R O C E D U R E 6. Disassemble LCD Panel and release 4pcs screw on the both LCD Bracket. 1,2 3 4 2-5 PDF created with pdfFactory Pro trial version www.pdffactory.
PAGE 6
D I S A S S E M B L Y P R O C E D U R E 5 6 O D D ODD Module M O D U L E The illustrations below show how to remove the ODD Module from the notebook. O D D Removing ODD Module M O D U L E 1. 2. 3. R E M O V A L 2 Release 1pcs screw on the rear Base Cover. Pull out the ODD Module from bottom side of notebook. Release 2pcs screw on the ODD Bracket. 1 3 2-6 PDF created with pdfFactory Pro trial version www.pdffactory.
PAGE 7
D I S A S S E M B L Y H D D M O D U L E P R O C E D U R E HDD Module The illustrations below show how to remove the HDD Module from the notebook. H D D M O D U L E R E M O V A L Removing HDD Module 1. Release 2pcs screws from bottom of notebook. 2. Pull out the HDD module from notebook. 1 2 M E M O R Y R E M O V A L Memory Module The illustrations below show how to remove the Memory module from the notebook. The SW1 Series Notebook comes standard without memory onboard.
PAGE 8
D I S A S S E M B L Y C P U P R O C E D U R E CPU Module The illustrations below show how to remove the CPU module from the notebook. The module contains CPU, CPU Thermal Pad and CPU Thermal Module. C P U R E M O V A L Removing CPU 1. Release 2pcs screw on Fan, pull out Fan Cable and remove Fan Module. 2. Release 4pcs screw with 4,3,2,1 order on the Cooler and pull out Cooler. 1 2 2-8 PDF created with pdfFactory Pro trial version www.pdffactory.
PAGE 9
D I S A S S E M B L Y 3. 4. T O P C O V E R M O D U L E . T O P C O V E R M O D U L E P R O C E D U R E To unlock CPU with minus screw driver and follow the direction of arrow below. Carefully pull out CPU upwards with your hand. TOP Cover module The illustrations below show how to disassemble and remove the Top Cover Module of the notebook. The module contains the Top Cover itself and Touch Pad Module. Removing Top Cover Module 1. Release 7pcs screws on the Base. 2.
PAGE 10
D I S A S S E M B L Y P R O C E D U R E 1 2 M / B M O D U L E R E M O V A L Removing Motherboard module 1. 2. 3. 4. Release 7pcs screws on the Main Board. Remove HDD bracket & Modem cable. Pull out DB/B and pull out Speaker R. Pull out M/B Module carefully from right side in the Base Cover to remove DVI or CRT connector and Modem Connector, and remove 1394 Connector and Audio Jack to separate the M/B from Base Cover. 5. Pull out Speaker L and remove IO/B cable & Power Jack cable.
PAGE 11
D I S A S S E M B L Y P R O C E D U R E 1 Remove IO board and speaker 4 2 - 11 PDF created with pdfFactory Pro trial version www.pdffactory.