® Terminator 2 Barebone System Model T2-R User Guide
E1431 First Edition V1 December 2003 Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Table of contents Notices ........................................................................................... 6 Safety information .......................................................................... 7 About this guide .............................................................................. 8 System package contents ............................................................ 10 Chapter 1: System introduction 1.1 1.2 1.3 1.4 Welcome! ....................................................
Table of contents Chapter 3: Starting up 3.1 3.2 3.3 3.4 Installing an operating system ............................................. Powering up ........................................................................ Support CD information ....................................................... 3.3.1 Running the support CD ........................................ 3.3.2 Drivers menu ......................................................... 3.3.3 Utilities .................................................
Table of contents 5.3 5.4 5.5 5.6 5.7 5.2.7 Pop-up window ...................................................... 5.2.8 Scroll bar ............................................................... 5.2.9 General help .......................................................... Main menu ........................................................................... 5.3.1 System Time ......................................................... 5.3.2 System Date ......................................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
About this guide Safeguards Audience This guide provides general information and installation instructions about the ASUS Terminator 2 barebone system. This guide is intended for experienced users and integrators with hardware knowledge of personal computers. How this guide is organized This guide contains the following parts: 8 1. Chapter 1: System introduction This chapter gives a general description of the ASUS Terminator 2.
Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task. Where to find more information Refer to the following sources for additional information and for product and software updates. 1.
System package contents Check your ASUS Terminator 2 package for the following items: 1. ASUS Terminator 2 barebone system with: • ASUS P4R8T motherboard • Floppy disk drive • Optical drive (optional)* • Modem (optional) 2. Power cable and plug 3. Support CD 4. User guide * CD-ROM/CD-RW/DVD-ROM/DVD-RW If any of the items is damaged or missing, contact your retailer immediately.
This chapter gives a general description of the ASUS Terminator 2. The chapter lists the system features including introduction on the front and rear panel, and internal components.
1.1 Welcome! Thank you for choosing the ASUS Terminator 2! The ASUS Terminator 2 is an all-in-one barebone system with a versatile home entertainment feature. The system comes in a stylish mini-tower casing, and powered by the ASUS P4R8T motherboard that supports Intel® Pentium® 4 Northwood/Prescott processor with an 800MHz FSB, and up to 2GB system memory. With unmatched video and audio capabilities, Fast Ethernet, and extensive connectivity, Terminator 2 is designed for the sophisticated.
3. Eject button. Press this button to eject the loading tray of the optical drive. 4. Second optical drive door. This door covers a second optical drive bay. 5. Power button. Press this button to turn the system on. 6. Power LED. When lit, this LED indicates that the system is ON. 7. HDD LED. This LED lights up when data is being read from or written to the hard disk drive 8. Front panel I/O door. Open this door to show the front panel input/output ports.
1.3 Rear panel The system rear panel includes the power socket and several I/O ports that allow convenient connection of devices. 1 2 16 3 4 5 6 7 8 17 9 10 18 11 19 12 20 13 14 14 15 1. GAME/MIDI port. This port connects a joystick, or game pad for playing games, and MIDI devices for audio editing. 2. Telephone port (optional). This port connects an RJ-11 cable jack. Connect one end of an RJ-11 cable to this port and the other end to the RJ-11 port of the telephone unit. 3.
9. Line Out port. This Line Out (lime) port connects a headphone or a speaker. In 4/6-channel mode, the function of this port becomes Front Speaker Out. 10. Line In port. This Line In (light blue) port connects a tape player or other audio sources. In 6-channel mode, the function of this port becomes Low Frequency Enhanced Output/Center. 11. Microphone port. This Microphone (pink) port connects a microphone. In 4/6-channel mode, the function of this port becomes Surround Speaker. 12. USB 2.0 ports.
1.4 Internal components The illustration below is the internal view of the system when you remove the top cover and the power supply unit. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing other system components. 1 3 6 2 4 9 8 7 5 10 11 1. 2. 3. 4. 5. 6. 16 Optical drive 5.25-inch empty optical drive bay Floppy disk drive Front panel cover Hard disk drive metal tray Chassis fan 7. ASUS P4R8T motherboard 8. DIMM sockets 9.
This chapter provides step-by-step instructions on how to install components in the system.
2.1 Preparation Before you proceed, make sure that you have all the components that you plan to install in the system. Basic components to install 1. 2. 3. 4. 5. Central processing unit (CPU) DDR Dual Inline Memory Module (DIMM) Expansion card(s) Hard disk drive Second optical drive Tool Phillips (cross) screw driver 2.2 Before you proceed Take note of the following precautions before you install components into the system. 1.
2.3 Removing the cover To remove the cover: 1. On the rear panel, locate the three screws that secure the cover to the chassis. 1 1 2. Use a Phillips (cross) screw driver to remove the cover screws. Keep the screws for later use. 1 2 2 2 3. Pull the cover slightly toward the rear panel until the side tabs are disengaged from the chassis. 4. Lift the cover, then set aside.
2.4 Removing the power supply You must remove the power supply unit (PSU) before you can install a central processing unit (CPU) and other system components. See page 33-35 for details on the PSU. To remove the PSU: 1. Lay the system on its side on a flat, stable surface. 2. Disconnect all power plugs from the optical drive and floppy disk drive. 3. Remove the screw that secures the PSU to the chassis. 3 4. Slide the PSU to the left until the side hook is disengaged from the chassis. 5.
2.5 Installing a CPU The P4R8T motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. This socket is specifically designed for Intel® Pentium® 4 Northwood/Prescott processor. 2.5.1 Removing the CPU fan and heatsink assembly The system package includes a pre-installed proprietary CPU fan and heatsink assembly to ensure optimum thermal condition and performance. DO NOT replace the proprietary CPU fan and heatsink with other models.
6. Disconnect the CPU fan cable from the CPU fan connector on the motherboard. 7. Lift the CPU fan and heatsink assembly, then set aside. 7 6 2.5.2 CPU installation To install the CPU: 1. Locate the 478-pin CPU socket on the motherboard. 2. Unlock the socket by pressing the lever sideways then lifting it up to a 90° angle. 3. Position the CPU above the socket such that its marked corner (gold mark) matches the base of the socket lever. 4.
2.5.3 Re-installing the CPU fan and heatsink assembly To re-install the CPU fan and heatsink assembly: 1. Position the CPU fan and heatsink assembly on top of the installed CPU. 1 2. Align the retention bracket with the rails on the side of the CPU fan. 3. Attach the retention bracket hook to the retention module hole. 4. Carefully press down the locking lever on the other side of the retention bracket. 5.
2.6 Installing a DIMM The motherboard comes with two Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 2GB system memory using unbuffered non-ECC PC3200/2700/2100 DIMMs. 2.6.1 Memory configurations You may install 64MB, 128MB, 256MB, 512MB, and 1GB DDR DIMMs into the DIMM sockets. Obtain DDR DIMMs only from ASUS qualified vendors. Refer to the table below. Visit the ASUS website (www.asus.com) for the latest Qualified Vendors List.
2.6.2 DIMM installation To install a DDR DIMM. 1. Locate the two DIMM sockets on the motherboard. 2. Unlock a socket by pressing the retaining clips outward. 3. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 4. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Retaining clips 3 2 2 4 4 1 A DDR DIMM is keyed with a notch so that it fits in only one direction.
2.7 Installing an expansion card In the future, you may need to install expansion cards. The motherboard has one PCI and one Accelerated Graphics Port (AGP) slot. The following sub-sections describe the slots and the expansion cards that they support. 2.7.1 Expansion slots PCI slot The PCI slot supports PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. AGP slot The AGP slot supports AGP 8X/4X cards.
2.7.2 Expansion card installation To install an expansion card. 1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card. 2. Pull the expansion card lock to the direction of the arrow. 2 Expansion card lock 3. Remove the metal bracket opposite the slot that you intend to use. PCI slot AGP slot 3 Metal brackets 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.
2.7.3 Configuring an expansion card After installing the expansion card, configure it by adjusting the software settings. 1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for information on the BIOS setup. 2. Assign an IRQ to the card. Refer to the tables on the next page. 3. Install the software drivers for the expansion card.
2.8 Installing a second optical drive The system comes with a pre-installed optical drive (DVD-RW, DVD-ROM, CD-RW, or CD-ROM) and an empty 5.25-inch drive bay for a second optical drive. Set your second optical drive as Slave device before connecting the IDE cable and power plug. Refer to the optical drive documentation on how to set the drive as a Slave device. To install a second optical drive: 1. Place the chassis upright. 2. Locate the front panel cover hooks. 3.
8. 9. Connect a power plug from the power supply unit to the power connector at the back of the optical drive. 8 Connect one end of the IDE 10 ribbon cable to the IDE interface at the back of the optical drive, matching the red stripe on the cable with Pin 1 on the IDE interface. 9 10. Connect one end of the optical drive audio cable to the 4-pin connector at the back of the optical drive. 11.
2.9 Installing a hard disk drive The system supports one UltraATA133 IDE hard disk drive (HDD). To install a hard disk drive: 1. Locate the HDD metal tray flathead lock screw on the other side of the chassis. 2. Remove the flat head screw using a Philips screw driver. Keep the screw for later use. 1 2 3. Slide the HDD metal tray outward until its slots are released from the tray locks. Tray locks 3 Lock slots Tray locks 4. 5.
6. Re-install the metal tray and the HDD by sliding it to the tray hooks. 7. Secure the HDD metal tray with the flat head screw you earlier removed. 8. Connect one end of the 40-pin IDE cable to the IDE connector on the drive. 9. Connect a 4-pin power plug from the power supply unit to the HDD power connector. 10. Connect the other end of the IDE ribbon cable to the primary IDE connector (blue connector labeled PRI_IDE) on the motherboard. See page 53 for the location of the primary IDE connector.
2.10 Re-installing the power supply unit After installing the system components and reconnecting the cables, re-install the power supply unit (PSU). To reinstall the PSU: 1. Connect the 4-pin and 20-pin power plugs to the ATX12V and ATXPWR connectors on the motherboard. See page 54 for the location of the power connectors. 1 1 2. Position the PSU over the chassis. 3. Align the PSU side hook with the metal slot located in the side of the optical drive bay. 4.
7 8 Power supply unit plugs 1 1 6 6. Connect the 4-pin power plug to the power connector of the floppy disk drive. 7. Connect the 4-pin power plug(s) to the power connector of the optical drive(s). 8. Connect the 4-pin power plug to the power connector of the hard disk drive. 2.10.1 Voltage selector The PSU has a 115V/230V voltage selector switch located at the side of the power socket. Use this switch to select the appropriate voltage according to the voltage supply in your area.
2.10.2 Power supply specifications Input characteristics Input Voltage Range Min Nom Max Range 1 90V 115V 132V Range 2 180V 230V 264V Input Frequency Range 47 Hz to 63 Hz Maximum Input AC Current 5A max. at 115Vac 3A max. at 230Vac, full load Inrush Current No hazards to occur and damage components Efficiency 65% min. at 115Vac and output full load Current Harmonic Meets EN61000-3-2 @ 100Vac/50Hz or 230 Vac/50Hz at full load EPA 50% min.
2.11 Replacing the cover To replace the cover. 1. Turn the chassis upright. 2. Position the front edge of the cover at least two inches from the front panel cover. Fit the cover tabs with the chassis rail and the front panel tabs. 3. Lower the rear edge of the cover as shown. 4. Push the cover slightly toward the front panel until it fits in place. 5. Secure the cover with three screws you earlier removed.
2.
To the rear panel RJ-11 jack Telephone Joystick Serial mouse PS/2 Mouse PS/2 KB Printer VGA monitor Line Out Recorder USB Mouse Power outlet RJ-45 38 Mic Chapter 2: Basic installation
Chapter 3 Starting up This chapter helps you power up the system and install drivers and utilities from the support CD.
3.1 Installing an operating system Terminator 2 supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 3.2 Powering up Press the system power button ( ) to enter the OS. Press to enter the system OS 3.
3.3.1 Running the support CD To begin using the support CD, place the CD in your optical drive. The CD automatically displays the Drivers menu if Autorun is enabled in your computer. Click an item to install Click an icon to display other information If Autorun is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD. 3.3.
3.3.3 Utilities The Utilities tab displays the applications and softwares that the motherboard supports. ASUS PC Probe This utility continuously monitors vital system information such as fan rotations, CPU temperature, and system voltages, and alerts you on any detected problems. This utility helps you keep your computer in a healthy operating condition. Install ASUS Update VX.XX.XX This item installs the ASUS Update that allows you to update the motherboard BIOS and drivers.
3.3.4 ASUS contact information Click the Contact tab to display the ASUS contact information. 3.3.5 Other information The icons on the top right of the screen provide additional information on the motherboard and the contents of the support CD.
3.4 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. 3.4.1 Multi-channel audio feature The AD1888 AC ‘97 audio CODEC provides 6-channel audio capability. Install the AD1888 Driver and Application from the support CD to activate the 6-channel audio feature. You must use 4-channel or 6-channel speakers for this setup.
6. Click the Test button to display the Test Listening Environment window. 7. Select the audio test path from the drop-down menu. 8. After selecting an option, test your setting by clicking the Play Test Noise button. While testing, you will see a black circle moving on the screen indicating the audio path. Audio path indicator The Play Test Noise button becomes Stop Playing button. Click this button at any time to stop playing. 9. Click the Close button when done. 10.
Adjusting the volume settings 1. After rebooting the system, click on the volume control icon on the Windows® taskbar to display the Volume Control window. 2. Click the Volume Control Advanced button. The Advanced Controls for Volume Control window appears. To achieve 6-channel audio capability when playing DVDs, check the boxes opposite AC3 SPDIF and PCM SPDIF. Click Close. Adjusting the microphone settings 1.
3.4.2 ASUS Instant Music The motherboard is equipped with a BIOS-based audio playback feature called Instant Music. This feature is supported by the onboard audio AC’97 CODEC and requires an optical drive (CD-ROM, DVD-ROM, CD-RW, or DVD-RW). 1. Instant Music only supports CDs in audio format. 2. Instant Music does not work if you installed and enabled an add-on sound card. 3. Instant Music only supports PS/2 keyboard. 4. Set the optical drive as secondary master device. See page 53 for details.
To use ASUS Instant Music: 1. 2. Ensure that the power cord is plugged to a grounded power source, so that the system has a standby power. Use either one of the two sets of special function keys on your keyboard to play audio CDs. These keys only function as indicated if you enabled the Instant Music item in BIOS. Instant Music function keys (Set 1) CD ON/OFF PLAY/PAUSE Esc F1 STOP/EJECT PREVIOUS NEXT F3 F4 F2 VOL. DOWN VOL.
This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
4.1 Introduction The ASUS P4R8T motherboard comes already installed in the ASUS Terminator 2 system. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. 4.2 Motherboard layout 23cm (9.06in) Flash BIOS IOC_MB CHA_FAN AUX ATI RS300 ATX12V FP_AUDIO CD AD1888 RTL 8201BL J1 LCD_PANEL MDC AGP1 VIA VT6202 ATI IXP200 BAT CLRTC USB56 PCI Slot 1 SB_PWR PRI_IDE SPDIF OUT USB2.
4.3 Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
4.4 Connectors This section describes and illustrates the connectors on the motherboard. See page 19 for the description of rear panel connectors. 1. Front panel USB connector (10-1 pin USB56) GND USBP3+ USBP3USB Power The USB56 header is connected to the USB_2 connector of the front panel I/O daughterboard. P4R8T ® P4R8T USB Port 2.
3. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) The PRI_IDE connector is for the UltraATA100 IDE hard disk ribbon cable. Connect the cable’s blue connector to the IDE connector, then connect the gray connector to a secondary master device (optical drive) and the black connector to the UltraATA100 primary master device (hard disk drive). Configure the hard disk drive and the optical drive as primary/secondary master device by adjusting their jumper settings.
5. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy disk drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY PIN 1 ® NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P4R8T P4R8T Floppy Disk Drive Connector 6.
7. Front panel audio connector (10-1 pin FP_AUDIO) Line out_L NC Line out_R MICPWR MIC2 This interface is connected to the J1 connector in the front panel I/O daugtherboard to support the front panel audio I/O ports. BLINE_OUT_L ® BLINE_OUT_R +5VA AGND FP_AUDIO P4R8T P4R8T Front Panel Audio Connector 8. Digital audio connector (4-1 pin SPDIF_OUT) The SPDIF_OUT is connected to the SPDIF_OUT2 connector in the front panel I/O daughterboard to support the optical S/PDIF port.
9. I/O extension module (22-pin IOC_MB) This connector is for the CGAEX extension module. GAME COM1 ® CGAEX IOC_DC ® P4R8T P4R8T IOC_MB Connector 10. Optional modem connector (10-1 pin MDC) This interface connects to the JP2 connector in the optional modem module.
11. System panel connector (8-1 pin PANEL) This connector accommodates several system front panel functions. Power LED IDE_LED– IDE_LED+ PLED– PLED+ IDE_LED Ground PWR PANEL ATX Power Switch* ® P4R8T * Requires an ATX power supply. P4R8T System Panel Connector • Power LED Lead This 2-pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
Chapter 4: Motherboard info
Chapter 5 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters.
5.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk.) 2. ASUS EZ Flash (Updates the BIOS using a floppy disk during POST.) 3. CrashFree BIOS 2 (Updates the BIOS using a bootable floppy disk or the support CD when the BIOS gets corrupted.) 4. ASUS Update (Updates the BIOS in Windows® environment.
Windows® XP environment 2. a. Insert a 1.44 MB floppy disk into the floppy disk drive. b. From your Windows desktop, click on Start, then select My Computer. c. Select the 3 1/2 Floppy Drive icon. d. Click File from the menu, then select Format. A Format 3 1/2 Floppy Disk window appears. e. Select Create an MS-DOS startup disk from the format options field, then click Start. Copy the original (or the latest) motherboard BIOS to the bootable floppy disk. 5.1.
2. The utility will copy the current system BIOS by default to the floppy disk. Make sure that the floppy disk is not write-protected and have enough space (at least 600KB) to store the file. A:\>afudos /oBIOSOLD.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done A:\> When the BIOS copy process is complete, the utility returns to the DOS prompt. 5.1.
The screen displays the status of the update process. The BIOS information on the screen is for reference only. What you see on your screen may not be exactly the same as shown. A:\>afudos /ip4r8t.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file ..... done Erasing flash .... done Writing flash ....
5.1.4 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash is built-in the BIOS LPC chip so it is accessible by simply pressing + during the Power-On Self Tests (POST). To update the BIOS using ASUS EZ Flash: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for your motherboard and rename it to P4R8T.ROM.
5.1.5 Recovering the BIOS with CrashFree BIOS 2 The CrashFree BIOS 2 auto recovery tool allows you to restore BIOS from the motherboard support CD, or from a floppy disk that contains the BIOS file, in case the current BIOS on the motherboard fails or gets corrupted. • Prepare the support CD that came with the motherboard or a floppy disk that contains the motherboard BIOS (P4R8T.ROM) before proceeding with the BIOS update process.
To recover the BIOS from the support CD: Make sure the optical drive is set as secondary master device when recovering the BIOS using the support CD. See page 53 for details. 1. Boot the system. 2. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... The system automatically checks the CD-ROM if there is no floppy disk found in the drive. 3. Place the support CD in the optical drive.
5.1.6 ASUS Update The ASUS Update is a utility that allows you to update the motherboard BIOS in Windows® environment. This utility is available in the support CD that comes with the motherboard package. ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP). To install ASUS Update: 1. Place the support CD in the optical drive. The Drivers menu appears. 2. Click the Utilities tab, then click Install ASUS Update VX.XX.XX.
3. If you selected updating/ downloading from the Internet, select the ASUS FTP site nearest you to avoid network traffic, or choose Auto Select. Click Next. 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file.
5.2 BIOS Setup program This motherboard supports a programmable Firmware Hub (FWH) that you can update using the provided utility described in section “5.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future.
5.2.1 BIOS menu screen Menu items Menu bar Configuration fields System Time System Date Legacy Diskette A [11:10:19] [Thu, 09/27/2003] [1.44M, 3.5 in.] Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave [ST321122A] [ASUS CDS520/] [Not Detected] [Not Detected] General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. System Information Sub-menu items Navigation keys 5.2.
5.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. Main menu items 5.2.5 Sub-menu items An item with a sub-menu on any menu screen is distinguished by a solid triangle before the item. To display the sub-menu, select the item and press . 5.2.
5.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears giving you an overview of the basic system information. Refer to section 5.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave [11:10:19] [Thu, 09/27/2003] [1.44M, 3.5 in.] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
5.3.4 Primary and Secondary IDE Master/Slave While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press Enter to display the IDE device information. Primary IDE Master Select the type of device connected to the system. Device : Hard Disk Vendor : Maxtor 6Y080L0 Size : 81.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
5.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values may cause the system to malfunction. Instant Music Configuration Configure CPU.
5.4.1 Instant Music Configuration Instant Music Option Instant Music Disable/Enable Instant Music feature. [Disabled] Instant Music [Disabled] Allows you to enable or disable the Instant Music feature in BIOS. Configuration options: [Disabled] [Enabled] • When Instant Music is enabled, the PS/2 keyboard power up feature is automatically disabled. See page 47 for details on the Instant Music feature. • The following item appears only if you enable the Instant Music option.
5.4.2 CPU Configuration The items in this menu show the CPU-related information auto-detected by BIOS. Configure advanced CPU settings Manufacturer Brand String Frequency FSB Speed : : : : Intel(R) Intel(R) Pentium(R) 4 Family CPU 2.40G 2400MHz 400MHz Cache L1 Cache L2 Cache L3 : 8 KB : 512 KB : 0 MHz Ratio Status : Locked Ratio Actual Value : 18 CPU Internal Thermal Control [Auto] CPU Internal Thermal Control [Auto] This item allows you to activate the CPU Internal Thermal control feature.
NorthBridge Configuration Init. Graphic Adapter Priority [PCI/AGP] DRAM CAS Select AGP Aperture Size UMA Frame Buffer Size [Slow] [64MB] [64MB] Select which graphics controller to use as the primary boot device. Init. Graphic Adapter Priority [PCI/AGP] Allows selection of the graphics controller to use as primary boot device. Configuration options: [PCI/AGP] [AGP/PCI] DRAM CAS Select [Slow] Allows you to select DRAM CAS speed.
SouthBridge Configuration AC97 Audio Device MC97 Modem Device Onboard LAN Device USB 1.1 OHCI Controllers USB 2.0 EHCI Controller [Auto] [Auto] [Enabled] [Enabled] [Enabled] Legacy USB Support [Auto] AC97 Audio Device [Auto] [Auto] allows the BIOS to detect whether you are using any audio device. If an audio device is detected, the onboard audio controller is enabled; if no audio device is detected, the controller is disabled.
5.4.4 Onboard Devices Configuration Configure ITE8712 Super IO Chipset Serial Port1 Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ Onboard Game Port Onboard MIDI Port [3F8/IRQ4] [378] [EPP+ECP] [1.9] [DMA3] [IRQ7] [Enabled] [Disabled] Allows BIOS to select Serial Port1 Base Addresses. Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address.
Onboard MIDI Port [Disabled] Allows you to select the MIDI port address or to disable the port. Configuration options: [Disabled] [300/330] 5.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items.
Palette Snooping [Disabled] When set to [Enabled], the pallete snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. Setting to [Disabled] deactivates this feature. Configuration options: [Disabled] [Enabled] PCI IDE BusMaster [Enabled] Allows BIOS to use PCI bus mastering when reading/writing to IDE devices.
5.5 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press Enter to display the configuration options. Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI ASIC Support [S1&S3] [Yes] [No] [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 5.5.1 Suspend Mode [S1&S3] Allows you to select the ACPI state to be used for system suspend.
5.5.5 APM Configuration Restore on AC Power Loss [Power Off] Power on with PS/2 Keyboard Power on with PS/2 Mouse RTC Resume [Disabled] [Disabled] [Disabled] Go into On/Off, or Suspend when Power button is pressed. Restore on AC Power Loss [Power Off] When set to [Power Off], the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss.
5.5.6 Hardware Monitor Hardware Monitor CPU temperature. MB Temperature CPU Temperature [36°C/96.5°F] [44°C/111°F] CPU Fan Speed Chassis Fan Speed [5234RPM] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [1.808V] [3.376V] [5.080V] [11.977V] SMART Q-Fan Function [Enabled] Fan Auto Mode Start Voltage [5.
The following items appear only when the Smart Q-Fan Function item is set to Enabled. Fan Auto Mode Start Voltage [5.0V] This item allows you to select the voltage for the auto start fan feature. The fan starts when the system reaches the specified voltage. Configuration options: [4.0V] [4.5V] [5.0V] [5.5V] [6.0V] Fan Auto Mode Start Temp [30ºC] Select the temperature for the auto start fan feature. The fan starts when the system reaches the specified temperature. Configuration options: [25ºC]...
5.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press Enter to display the sub-menu. Boot Settings Specifies the Boot Device Priority sequence. Boot Device Priority Boot Settings Configuration Security 5.6.1 Boot Device Priority Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [First Floppy Drive] [PM-ST320413A] [PS-ASUS CD-S340] Specifies the boot sequence from the available devices.
5.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo Add On ROM Display Mode Bootup Num-Lock Wait for ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 5.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press Enter to display the configuration options. Security Settings Supervisor Password User Password Not Installed Not Installed to change password. again to disable password.
If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section 4.3 “Jumper” for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Not Installed Not Installed to change password.
The message “Password Installed” appears after you have successfully set your password. The User Password item now shows Installed. To change the user password, follow the same steps as in setting a user password Clear User Password Select this item if you wish to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
5.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Exit system setup after saving the changes. F10 key can be used for this operation. Load Setup Defaults Pressing does not immediately exit this menu. Select one of the options from this menu or from the legend bar to exit.
Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select [Yes] to discard any changes and load the previously saved values. Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select [Yes] to load the default values.
Chapter 5: BIOS setup
