® TUEG-VM Intel® 815EG Chipset microATX Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described herein, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except for documentation kept by the purchaser for backup purposes, without the expressed written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel):+886-2-2890-7123 (English) Fax: +886-2-2890-7698 Newsgroup: cscnews.asus.com.tw Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.
CONTENTS 1. INTRODUCTION ............................................................................. 7 1.1 How This Manual Is Organized .................................................. 7 1.2 Item Checklist ............................................................................. 7 2. FEATURES ........................................................................................ 8 2.1 The ASUS TUEG-VM ............................................................... 8 2.
CONTENTS 4.3 Main Menu ................................................................................ 52 4.3.1 Primary & Secondary Master/Slave .............................. 53 4.3.2 Keyboard Features ......................................................... 56 4.4 Advanced Menu ........................................................................ 58 4.4.1 Chip Configuration ........................................................ 61 4.4.2 I/O Device Configuration .....................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1. INTRODUCTION 1. INTRODUCTION Manual / Checklist 1.1 How This Manual Is Organized This manual is divided into the following sections: 1. 2. 3. 4. 5. 6. 7. INTRODUCTION FEATURES HARDWARE SETUP BIOS SETUP SOFTWARE SETUP SOFTWARE REFERENCE APPENDIX Manual information and checklist Production information and specifications Instructions on setting up the motherboard.
2. FEATURES 2.1 The ASUS TUEG-VM The ASUS TUEG-VM motherboard is carefully designed for the demanding PC user who wants advanced features processed by the fastest processors. 2.1.1 Specifications • 2.
2. FEATURES • • • • • • • • • • CNR Support: A Communication and Networking Riser (CNR) slot provides an interface to support very affordable multichannel audio, V.90 analog modem, Home PNA, 10/100 Ethernet networking, USB hub, as well as future technologies such as xDSL. PCI Expansion Slots: Provides three 32-bit PCI (PCI 2.2 compliant) expansion slots. All PCI slots can support Bus Master PCI cards, such as SCSI or LAN cards. (PCI supports up to 133MB/s maximum throughput.
2. FEATURES 2.1.2 Specifications–Optional Components The following onboard components are optional at the time of purchase: • • Smart Networking: Features 3Com’s 3C920 Fast Ethernet controller, which supports Wired for Management, remote wake-up, and OnNow initiatives to reduce Total Cost of Ownership (TCO). Onboard Audio: AC’97 Audio chipset supports the latest audio sound circuitry. A software package helps setup the multi-channel PC sound system. 2. FEATURES Performance 2.1.
2. FEATURES • PC’99 Compliant: Both the BIOS and hardware levels of ASUS smart series 2. FEATURES Intelligence motherboards are PC’99 compliant. The new PC’99 requirements for systems and components are based on the following high-level goals: support for Plugn-Play capability and power management for configuring and managing all system components, and 32-bit device drivers and installation procedures for Windows95/98/NT .
2. FEATURES 2.2 TUEG-VM Motherboard Components See opposite page for locations. Location Processor Support Socket 370 for Pentium III/Celeron/Tualatin CPUs.. ............... 2 Feature Setting DIP Switches ................................................... 8 2. FEATURES MB Components Chipsets Intel 82815G Graphics Memory Controller Hub (GMCH) ...... 3 Intel 82801BA I/O Controller Hub (ICH2) .......................... 13 2Mbit Firmware Hub (FWH) .................................................
2. FEATURES 2.2.1 Component Locations 1 2 3 4 5 6 78 2.
3. HARDWARE SETUP 3.1 TUEG-VM Motherboard Layout CPU_FAN PS/2KBMS T: Mouse B: Keyboard USB Top: Line Out COM2 Line In Mic In SMARTCARD Super I/O 2 3 4 5 PRIMARY IDE 0 1 LED LCDTV AUX 1 MIC2 1 HEADPHONE ® MODEM PCI1 AAPANEL Audio Codec AUD_EN CD TUEG-VM Intel I/O Controller Hub (ICH2) PCI2 JTPWR WOL_CON PCI3 CNR_SLOT R210 2Mbit Firmware Hub (FWH) USB2 LAN_EN 3Com 3C920 Fast Ethernet 1 CR2032 3V Lithium Cell CMOS Power AFPANEL GAME_AUDIO 3.
3. HARDWARE SETUP 3.2 Layout Contents Motherboard Settings 1) JEN 2) USBPWR1 USBPWR2 3) USBCNR1/USBCNR2 4) AUD_EN1 5) LAN_EN 6) KBPWR 7) DSW p. 18 JumperFree™ Mode (Enable/Disable) p. 19 USB Device Wake Up (Enable/Disable) p. 19 p. 20 p. 20 p. 21 p. 22 USB/CNR Selection (USB2 Connect/CNR) Onboard Audio CODEC Setting (Enable/Disable) Onboard LAN Setting (Enable/Disable) Keyboard Power Up (Enable/Disable) CPU External Frequency Setting p. 24 p. 26 p. 27 p.
3. HARDWARE SETUP 13) WOR 14) LCDTV p. 39 Wake-On-Ring Connector (2 pins) p. 40 LCD-TV Headers (18-1 pins/18 pins) 15) USB2 16) ATXPWR p. 40 USB Headers (5-1 pins) p. 41 ATX Power Supply Connector (20 pins) 17) PWRLED (PANEL) p. 42 System Power LED Lead (3-1 pins) 18) KEYLOCK (PANEL) p. 42 Keyboard Lock Switch Lead (2 pins) 19) SPEAKER (PANEL) p. 42 System Warning Speaker Connector (4 pins) 20) MSG.LED (PANEL) p. 42 System Message LED (2 pins) 21) SMI (PANEL) p.
3. HARDWARE SETUP 3.3 Hardware Setup Procedure Before using your computer, you must complete the following steps: • Check Motherboard Settings • Install Memory Modules • Install the Central Processing Unit (CPU) • Install Expansion Cards • Connect Ribbon Cables, Panel Wires, and Power Supply 3.4 Motherboard Settings 3. H/W SETUP Motherboard Settings WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips.
3. HARDWARE SETUP Motherboard Feature Settings The motherboard’s onboard functions are either adjusted through jumpers or DIP switches. When using DIP switches, the white block represents the switch’s position. The example below shows all the switches in the OFF position. ON 1 2 3 4 5 DSW ON OFF ® TUEG-VM TUEG-VM DIP Switches 1. Frequency Selection 2. Frequency Selection 3. Frequency Selection 4. Frequency Selection 5. Frequency Selection. 3.
3. HARDWARE SETUP 2) USB Device Wake Up (USBPWR1,USBPWR2) These allow you to disable or enable the USB device wake up function. Set these jumpers to Enable if you wish to use your USB devices to wake up your computer. This feature requires an ATX power supply that can supply at least 2A on the +5VSB lead. The default is set to Disable because not all computers have the appropriate ATX power supply. Your computer will not power ON if you set this to Enable and do not have the appropriate ATX power supply.
3. HARDWARE SETUP 4) Onboard Audio CODEC Setting (AUD_EN1) (available on audio model only) The onboard audio CODEC may be enabled or disabled using all of these jumpers. Disable the onboard audio CODEC if you are using a PCI audio card on any of the expansion slots or a primary audio/modem CNR on a CNR slot (see CNR Slot later in this section). If using a PCI audio expansion card, Onboard AC97 Audio Controller in 4.4.2 I/O Device Configuration must also be disabled.
3. HARDWARE SETUP 6) Keyboard Power Up (KBPWR) This allows you to disable or enable the keyboard power up function. Set this jumper to Enable if you wish to use your keyboard (by pressing ) to power up your computer. This feature requires an ATX power supply that can supply at least 300mA on the +5VSB lead. The default is set to Enable because not all computers have the appropriate ATX power supply.
3. HARDWARE SETUP 7) CPU External Frequency Setting (DSW) This option tells the clock generator what frequency to send to the CPU, DRAM, AGP, and the PCI bus. This allows the selection of the CPU’s External frequency. IMPORTANT: 1. In JumperFree mode, all dip switches must be set to OFF. 2. When JumperFree mode is enabled, use BIOS setup in place of these switches (see CPU Internal Frequency in 4.4 Advanced Menu).
3. HARDWARE SETUP External Frequency Table The following table is for use by experienced motherboard installers only. Overclocking can result in system instability or even shortening the life of the processor. Frequency Selection Switches 1 2 3 4 5 66:100 66:100 66:100 66:100 66:100 66:100 66:100 66:100 100:100 100:100 100:100 64.4 60.0 66.0 68.3 70.0 75.0 80.0 83.0 99.6 90.0 100.0 99.6 90.0 100.0 102.5 105.0 112.5 120.0 124.5 99.6 90.0 100.
3. HARDWARE SETUP 3.5 System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM). One side (with memory chips) of the DIMM takes up one row on the motherboard. Memory speed setup is recommended through SDRAM Configuration in 4.4.1 Chip Configuration. Install memory in any combination as follows: 3.
3. HARDWARE SETUP 3.5.2 Memory Installation WARNING! Make sure that you unplug the power supply when adding or removing memory modules or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards (see 3.3 Hardware Setup Procedure for more information). Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation shown.
3. HARDWARE SETUP 3.6 Central Processing Unit (CPU) The motherboard provides a ZIF Socket 370. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case, then purchase a fan before you turn on your system. WARNING! Be sure that there is sufficient air circulation across the processor’s heatsink by regularly checking that your CPU fan is working.
3. HARDWARE SETUP 3.7 Expansion Cards WARNING! Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 3.7.1 Expansion Card Installation Procedure 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers or switches. 2.
3. HARDWARE SETUP 3.7.2 Assigning IRQs for Expansion Cards Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If your motherboard has PCI audio onboard, an additional IRQ will be used. If your motherboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free. Standard Interrupt Assignments 3.
3. HARDWARE SETUP 3.7.3 Communication and Networking Riser (CNR) Slot This connector supports a specially designed network, audio, or modem riser card. Main processing is done through software and controlled by the motherboard’s system chipset. This provides upgradeable network, audio, and/or modem solutions at an incredibly low cost. NOTE: CNRs are not included with this motherboard. ® 3. H/W SETUP Expansion Cards TUEG-VM TUEG-VM Communication & Networking Riser Connectors CNR Restrictions: 1.
3. HARDWARE SETUP 3.8 Connectors 3.8.1 External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors.
3. HARDWARE SETUP 3) Universal Serial BUS Ports 0 & 1 (Black two 4-pin USB) Two USB ports are available for connecting USB devices. For additional USB ports, you can use the USB headers (see USB Headers later in this section) and mount it to the chassis. Universal Serial Bus (USB) 3. H/W SETUP Connectors 4) Parallel Port Connector (Burgundy 25-pin PRINTER) You can enable the parallel port and choose the IRQ through Onboard Parallel Port (see 4.4.2 I/O Device Configuration).
3. HARDWARE SETUP 5) Serial Port Connectors (Teal/Turquoise 9-pin COM1, 10-1 pin COM2) One serial port is ready for a mouse or other serial devices. A second serial port is available using a serial port bracket connected from the motherboard to an expansion slot opening. See Onboard Serial Port 1/2 in 4.4.2 I/O Device Configuration for settings. COM 1 Serial Port (9-pin male) 3.
3. HARDWARE SETUP 7) Game/MIDI Connector (Gold 15-pin GAME_AUDIO) (optional) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing professional audio. Game/MIDI (15-pin female) SETUP 3.3. H/W SETUP DMA Channels Connectors 8) Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) Line Out (lime) can be connected to headphones or preferably powered speakers.
3. HARDWARE SETUP 3.8.2 Internal Connectors 1) Floppy Disk Drive Connector (34-1pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 5 plugged). FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. ® TUEG-VM 3.
® TUEG-VM TUEG-VM IDE Connectors Primary IDE Connector Secondary IDE Connector 3. HARDWARE SETUP NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PIN 1 3. H/W SETUP Connectors 3) IDE Activity LED (2-pin IDELED) This connector supplies power to the cabinet’s IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. TIP: If the case-mounted LED does not light, try reversing the 2-pin plug.
3. HARDWARE SETUP ® Rotation +12V GND Rotation +12V GND WARNING! Airflow across the CPU and onboard heatsinks is imperative, and the corresponding pins should be used accordingly. These are not jumpers, do not place jumper caps over these pins. CPU_FAN PWR_FAN CHA_FAN Rotation +12V GND TUEG-VM TUEG-VM 12-Volt Cooling Fan Power 3.
3. HARDWARE SETUP 7) Internal Microphone Connector (3-pin MIC2) This connector allows you to connect chassis mounted microphone to the motherboard. MIC2 Ground MIC Input MIC Power ® 3 1 TUEG-VM TUEG-VM Internal Microphone Connector 3. H/W SETUP Connectors 8) ASUS iPanel Connector (24-1 pin AFPANEL) This connector allows you to connect an optional ASUS iPanel, an easy to access drive bay with front I/O ports, status LEDs, and space reserved for a hard disk drive.
3. HARDWARE SETUP 10) SMB Connector (6-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. SMBus devices communicate by means of the SMBus with an SMBus host and/ or other SMBus devices. SMBus is a specific implementation of an I2C bus, which is a multi-device bus; that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer. SMB +3V SMBDATA Ground ® SMBCLK Key TUEG-VM 1 3.
3. HARDWARE SETUP 12) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output. The connector powers up the system when a wake up packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake On LAN or PCI Modem is enabled (see 4.5.1 Power Up Control) and that the system has an ATX power supply with at least 720mA +5V standby power.
3. HARDWARE SETUP +5V ® TVHSYNC GND DD2 DD0 LCDTV GND DD11 DD9 DD7 GND DD5 CLKOUT1 +1.8V LTVDA GND BLANK LTVCL +3V ROMSEN TVVSYNC GND DD4 DD3 DD1 GND 14) LCD-TV Headers (18-pin, 18-1 pin LCDTV) These headers require an optional LCD module for LCD output or a TV-out module for TV output. DD10 GND DD8 DD6 CLKOUT0 GND 1 TUEG-VM LCD-TV Headers +5V PCIRST# TUEG-VM 3.
3. HARDWARE SETUP 16) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power supply. The plug from the power supply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned.
3. HARDWARE SETUP The following illustration is for items 18–24. Reset Ground MLED+ MLEDExtSMI# Ground PWR GND PLED+ PLEDKeylock Ground Power LED Speaker Connector +5V Ground Ground Speaker Keyboard Lock ® Message LED TUEG-VM SMI Lead Reset SW ATX Power Switch* * Requires an ATX power supply. TUEG-VM System Panel Connectors 3.
3. HARDWARE SETUP 3.9 Starting Up the First Time 1. After all connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ), and the power input voltage is set to comply with the standard used in your country (220V-240V or 110-120V). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4.
3. HARDWARE SETUP 7. During power-on, hold down to enter BIOS setup. Follow the instructions in 4. BIOS SETUP. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system.
4. BIOS SETUP 4.1 Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4. BIOS SETUP 5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. 6. Type a filename and the path, for example, A:\XXX-XX.XXX and then press . 4.
4. BIOS SETUP 4.1.2 Updating BIOS Procedures WARNING! Update the BIOS only if you have problems with the motherboard and you know that the new BIOS revision will solve your problems. Careless updating can result in your motherboard having more problems! 4. BIOS SETUP Updating BIOS 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONTACT INFORMATION on page 3 for details) and save to the boot floppy disk you created earlier. 2. Boot from the floppy disk. 3.
4. BIOS SETUP 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary. This minimizes the possibilities of boot problems in case of update failures. When the programming is done, Flashed Successfully appears. 8. Follow the onscreen instructions to continue. 4. SETUP 4.
4. BIOS SETUP 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that can be updated using the provided utility as described in 4.1 Managing and Updating Your BIOS. The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section describes how to configure your system using this utility. Even if you are not prompted to use the Setup program, at some time in the future you may want to change the configuration of your computer.
4. BIOS SETUP 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program.
4. BIOS SETUP General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program.
4. BIOS SETUP 4.3 Main Menu When the Setup program is accessed, the following screen appears: 4. BIOS SETUP Main Menu System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the or + keys to move between the hour, minute, and second fields.