BIOSガイド Motherboard PRIME / ProArt / TUF GAMING AMD 600 Series
J21327 改訂版 V2 2022年10月 Copyright © 2022 ASUSTeK COMPUTER INC. All Rights Reserved. 本書およびそれに付属する製品は著作権法により保護されており、その使用、複製、頒布および逆コンパイル を制限するライセンスのもとにおいて頒布されます。購入者によるバックアップ目的の場合を除き、ASUSTeK Computer Inc.
もくじ 1 2 UEFIとは..............................................................................................................4 UEFI BIOS Utility.................................................................................................5 2.1 EZ Mode...................................................................................................................6 2.2 Advanced Mode....................................................................................................7 2.
UEFI BIOS設定 1 UEFIとは ASUS UEFI BIOSは、従来のキーボード操作だけでなくマウスでの操作も可能となったグラフ ィカルでユーザーフレンドリーなインターフェイスです。OSを使用するのと同じくらいに簡単に 操作することができます。* EFI (UEFI) が従来のBIOSと同じ機能を持つことから、ASUSはEFI (UEFI) を「UEFI BIOS」、 「BIOS」と表記します。 UEFI(Unified Extensible Firmware Interface)は、従来パソコンのハードウェア制御を担ってきた BIOS に代わる、OS とファームウェアのインターフェイス仕様です。UEFIは非常に高機能な最新の ファームウェアで従来のBIOSと違い拡張性に富んでいます。UEFIの設定はマザーボードのCMOS RAM(CMOS)に保存されています。通常、UEFIの既定値はさまざまな環境で最適なパフォーマン スを実現できるように設定されています。以下の状況以外では、既定値のままで使用することをお 勧めします。 • システム起動中にエラーメッセージが表示されUEFI BIOS Uti
2 UEFI BIOS Utility BIOS(Basic Input and Output System) とは、マザーボードに接続されたコンポーネント・デバイ スを制御するシステムプログラムです。コンピューターの起動時に最初に起動するプログラムで、 記憶装置の構成、オーバークロック設定、電源の管理、起動デバイス設定などのシステムハードウ ェアの設定をすることができます。 マザーボードにはBIOSに代わるUEFI (Unified Extensible Firmware Interface)が搭載されています。 UEFI BIOS Utility では各種パラメーターの調整や各種機能の有効/無効、BIOSイメージの更新な どを行なうことができます。 コンピューターの起動時にUEFI BIOS Utilityを起動する システムは起動時にPOST (Power On Self Test) と呼ばれる起動時の自己診断テストを実行します。 このPOST中にまたはを押すことでUEFI BIOS Utility を起動することができます。 • マウスでUEFI BIOS Utilit
2.
2.
メニューバー 画面上部に表示されるメニューバーはカテゴリーを表しています。各カテゴリーで設定できる内容は 次のとおりです。 My Favorites 登録したお気に入り項目 Main 基本システム設定 Ai Tweaker オーバークロック設定 Advanced 拡張システム設定 Monitor システム温度/電力状態の表示およびファンの設定 Boot システム起動設定 Tool 独自機能 Exit 終了メニューおよび既定値の読み込み メインアイテム 設定可能なアイテムまたは各種情報のタイトルが表示されます。 サブアイテム サブアイテムが含まれる項目には矢印マークが表示されています。 表示言語 UEFI BIOS Utility で表示する言語を選択することができます。 My Favorites ツリーマップから頻繁に使用する項目をお気に入りとして登録することで、画面の切り替えなどの 面倒な操作をせずに一画面で各種設定を変更することができるようになります。ショートカットキ ーは です。 詳細は「My Favorites」をご参照ください。 Qfan Contr
AURA オンボードAura LEDのオン/オフを設定することができます。RGBヘッダーおよびアドレサブルヘ ッダーは S0 電源オン時のみ動作します。ショートカットキーは です。 [All On] すべてのLEDをオン [Stealth Mode] すべてのLEDをオフ [Aura Only] Aura LEDをオン/機能LEDをオフ [Aura Off] Aura LEDをオフ/機能LEDをオン ReSize BAR システムにResize BAR対応PCIeデバイスが取り付けられている場合のResize BARサポートの有 効/無効を設定します。 [OFF] Resizable BARを無効にします。 [ON] Resizable BARを有効にします。CSM (Compatibility Support Module) は無効 になります。 Hot Keys (操作ガイド) UEFI BIOS Utilityを操作するためのキーボードの基本操作一覧を表示します。 スクロールバー 設定項目が画面に収まりきらない場合は、スクロールバーがメニュー画面の右側に表示されま す
2.
ファンの回転数を手動で設定する プロファイルの「Manual」を選択することで、ファンの回転数を手動で設定することができます。 スピードポイント マニュアル設定 手順 1. 設定を変更するファンを選択し、プロファイルの「Manual」を選択します。 2. スピードポイントをドラッグして、CPU温度に対するファンの回転数を設定します。 3.
3 My Favorites 頻繁に使用する項目をお気に入りとして登録することで、画面の切り替えなどの面倒な操作をせ ずに一画面で各種設定を変更することができます。 12 PRIME / ProArt / TUF GAMING AMD 600 Series BIOSガイド
お気に入り項目を追加する 手順 1. Advanced Modeでキーボードのを押すか「MyFavorite」をクリックし、Setup Tree Mapを開きます。 2. Setup Tree Mapでお気に入りに登録したい項目を選択します。 メインメニュー パネル 追加した項目 サブメニュー パネル すべて削除 既定値に戻す 3. まず、メインメニューパネルでカテゴリーを選択し、次にサブメニューパネルでお気に入り を に追加したい項目を選択します。お気に入りに追加したい項目でを押すか クリックして項目を追加します。 次の項目はお気に入りに追加することはできません: • ユーザー管理項目(システム言語や起動デバイス優先順位など) • ユーザー設定項目(ASUS SPD Informationやシステム日付や時間など) 4. 「Exit (ESC)」をクリックするか、を押してメインメニューに戻ります。 5.
4 Main Advanced Modeのメインメニューでは、マザーボード、CPU、メモリーの基本的な情報を表示す る他に、表示言語、日時、セキュリティの設定を行なうことができます。 Security システムセキュリティ設定の変更が可能です。 14 PRIME / ProArt / TUF GAMING AMD 600 Series BIOSガイド
• パスワードを忘れた場合、CMOSクリアを実行しパスワードを削除します。CMOSクリアの 手順については、お使いのマザーボードのユーザーガイドをご覧ください。 • パスワードを削除すると、画面上の「Administrator」または「User Password」には既 定値の「Not Installed」と表示されます。パスワードを再び設定すると、 「Installed」と 表示されます。 Administrator Password 管理者パスワードを設定するとUEFI BIOS Utilityへのアクセスを制限することができます。UEFI BIOS Utility起動時にパスワードが要求されます。 管理者パスワードの設定手順 1. 「Administrator Password」を選択します。 2. 「Create New Password」ボックスにパスワードを入力し、を押します。 3.
5 Ai Tweaker 高度なシステムの調整をすることができます。 不適切な値を設定した場合、システムの誤作動や故障などの原因となる恐れがあります。設定 を変更する際は十分ご注意ください。 本項目で表示される設定オプションは取り付けたCPUとメモリーにより異なります。 スクロールすることで画面の外に隠れているコンテンツを表示することができます。 16 PRIME / ProArt / TUF GAMING AMD 600 Series BIOSガイド
Ai Overclock Tuner CPUのオーバークロックオプションを選択して、CPUのベースクロック (基本動作周波数) などを 設定することができます。 [Auto] 標準ベースクロックで動作 [Manual] ベースクロックを任意に設定可能 [EXPO I] EXPO メモリータイミング (CL, TRCD, TRP, TRAS) およびASUSにより最適化さ れたその他のメモリーパラメーターをロード [EXPO II] メモリーモジュールのデフォルトEXPOプロファイルをロード。メモリーモジュ ールにEXPOプロファイルが検出されない場合は、ASUSにより最適化されたメ モリーパラメーターをロード [DOCP I] D.O.C.P (Direct Over Clock Profile) メモリータイミング (CL, TRCD, TRP, TRAS) およびASUSにより最適化されたその他のメモリーパラメーターをロード [DOCP II] メモリーモジュールのデフォルトD.O.C.P.プロファイルをロード。メモリーモジュ ールにD.O.C.P.
D.O.C.P. D.O.C.P (Direct Over Clock Profile) を選択します。各プロファイルはメモリー動作周波数タイミン グ、電圧が異なります。 DRAM Frequency メモリーの動作周波数を設定します。設定できる項目は、BCLK(ベースクロック)の周波数設定に よって異なります。Autoに設定すると、最適な設定が適用されます。 設定オプション: [Auto] [DDR5-2000MHz] - [DDR5-20000MHz] FCLK Frequency FCLK周波数を設定します。 設定オプション: [Auto] [800MHz] - [3000MHz] Core Performance Boost CPUとメモリーのオーバークロックを自動的に行い、システムのパフォーマンスを向上させる機能 の有効/無効を設定します。 設定オプション: [Auto] [Enabled] [Disabled] CPU Core Ratio CPUコアの動作倍率を設定します。 設定オプション: [Auto] [12.00] - [100.
Calibrated Temperature Threshold to switch back CPUがデフォルトモードに戻るタイミングを制御するために、キャリブレーション温度の しきい値を設定します。温度がしきい値より高い場合、CPUはデフォルトに戻ります。温度 がしきい値より低く、かつ電流が電流しきい値より高い場合、CPUはOCモードに移行しま す。単位は摂氏です。 設定オプション: [Auto] [0] - [140] Hysteresis 数値を低く設定するとしきい値を超えた際の過渡応答が高速になり、数値を高く設定す るとしきい値を超えた際の過渡応答は遅くなります。 設定オプション: [Auto] [0] - [255] DRAM Timing Control メモリーのアクセスタイミングに関する設定を行うことができます。既定値に戻すには、キーボ ードで [auto] と入力し で決定します。 メモリーのアクセスタイミングを変更するとシステムが不安定になる場合があります。不安定 になった場合は、既定値に戻してください。 Primary Timings DRAM CAS# Laten
DRAM RAS# to RAS# Delay S 設定オプション: [Auto] [1] - [31] Tfaw 設定オプション: [Auto] [1] - [127] DRAM WRITE to READ Delay L 設定オプション: [Auto] [1] - [127] DRAM WRITE to READ Delay S 設定オプション: [Auto] [1] - [31] TrdrdScl 設定オプション: [Auto] [1] - [15] TrdrdSc 設定オプション: [Auto] [1] - [15] TrdrdSd 設定オプション: [Auto] [1] - [15] Trdrddd 設定オプション: [Auto] [1] - [15] TwrwrScl 設定オプション: [Auto] [1] - [63] TwrwrSc 設定オプション: [Auto] [1] - [15] TwrwrSd 設定オプション: [Auto] [1] - [15] TwrwrDd 設定オプション: [Auto] [1] - [15] Twrrd 設定オプション: [Auto] [1] - [15] Tr
Rtt Park 設定オプション: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3 (80)] [RZQ/4 (60)] [RZQ/6 (40)] [RZQ/7 (34)] Rtt Park Dqs 設定オプション: [Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3 (80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)] ProcODT 設定オプション: [Auto] [High Impedance] [480 ohm] [240 ohm] [160 ohm] [120 ohm] [96 ohm] [80 ohm] [68 ohm] [60 ohm] [53 ohm] [48 ohm] [43 ohm] [40 ohm] [36 ohm] [34 ohm] [32 ohm] [30 ohm] [28 ohm] [26 ohm] [25 ohm] Proc Data Drive Strength 設定オプション: [Auto] [High Impeda
SOC EDC Limit System on a Chip Electrical Design Current Limit。マザーボードの電気的制限による電 流供給能力。マザーボードのプログラムされたボードSOC EDC上限まで調整することがで きます。単位はアンペア (A) です。 設定オプション: [Auto] [0] - [65535] Precision Boost Overdrive Scalar [Auto] 1x のスカラーで動作 (通常動作) [Manual] カスタマイズした値のスカラーで動作 次の項目は「Precision Boost Overdrive Scalar」を [Manual] に設定した場合にのみ表示され ます。 Customized Precision Boost Overdrive Scalar Precision Boost Overdriveは、使用するブースト電圧の最大値 (指定の最大値を超えて動 作) と、その電圧を維持する時間を増加させます。入力した値が大きいほど使用するブース ト電圧は高くなり、その電圧を維持する時間は長くなる可能性があります。 設
Curve Optimizer Curve Optimizer すべてのコアまたは特定のコアのAVFSカーブを調整し、カーブを上書きすることでCPUのパ フォーマンスを向上させることができます。大きい値を設定することで、電圧上限は高くなり ます。 設定オプション: [Auto] [All Cores] [Per Core] 次の項目は「Curve Optimizer」を [All Cores] に設定すると表示されます。 All Core Curve Optimizer Sign すべてのコアのAVFSカーブのシフト方向を設定します。Positiveに設定するとカーブは上にシ フトし高い電圧使用することができるようになり、Negativeに設定するとカーブは下にシフト し低い電圧を使用することができるようになります。 設定オプション: [Positive] [Negative] All Core Curve Optimizer Magnitude カーブシフトの大きさを整数で設定します。値が大きいほどシフトの大きさは大きくなりま す。 設定オプション: [0] - [30] 次の項目は「Curve Optim
Digi+ VRM VRM Initialization Check VRMの初期化中に何らかのエラーが発生した場合、本機能を有効に設定しているとPOST コード76/77でシステムがハングします。 設定オプション: [Disabled] [Enabled] CPU Load-line Calibration ロードラインはAMD VRM仕様で定義されており、CPUに供給される電圧に影響します。 CPUの動作電圧はCPUの負荷に比例して低下します。ロードラインキャリブレーションを 高くすると、負荷電圧が高くなりオーバークロックパフォーマンスは向上しますが、CPUと VRMの温度は上昇します。 設定オプション: [Auto] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5:Recommended for OC] [Level 6] [Level 7] [Level 8] 実際のパフォーマンスは取り付けられたCPUの仕様により異なります。 サーマルモジュールは取り外さないでください。温度条件を監視する必要があります。 CPU Current Capabilit
CPU Power Phase Control CPU電源フェーズの制御方法を設定します。 [Auto] 自動的に電源フェーズを制御します。 [Standard] CPUによりアクティブフェーズ数を制御します。 [Optimized] ASUSプロファイルによる制御。 [Extreme] 最大フェーズで動作します。 [Manual] 電源フェーズの制御方法を手動で設定します。 この項目を [Extreme] に設定する場合は、サーマルモジュールは取り外さないでください。温 度条件を監視する必要があります。 次の項目は「CPU Power Phase Control」を [Manual] に設定すると表示されます。 Power Phase Response 電源フェーズの応答速度を設定します。 設定オプション: [Ultra Fast] [Fast] [Medium] [Regular] VDDSOC Load-Line Calibration 設定オプション: [Auto] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6
次の項目は「VDDSOC Power Phase Control」を [Manual] に設定した場合にのみ表示され ます。 Power Phase Response 電源フェーズの応答速度を設定します。 設定オプション: [Ultra Fast] [Fast] [Medium] [Regular] Performance Bias 特定のソフトウェア実行時にパフォーマンスの最適化を図る機能の有効/無効を設定します。 設定オプション: [Auto] [None] [CB R23] [GB3] Tweaker’s Paradise Clock Spread Spectrum クロックスペクトラム拡散の有効/無効を設定します。 設定オプション: [Auto] [Enabled] [Disabled] 1.8V PLL Voltage 1.8V PLL電圧を設定します。 設定オプション: [Auto] [1.50000] - [2.50000] 1.8V Standby Voltage 1.8V スタンバイ電源電圧を設定します。 設定オプション: [Auto] [1.50000] - [2.
Custom Algorithms 独自のアルゴリズムをカスタマイズしてブースト動作を調整し、電力効率、温度、パフォーマンス を最適化します。最大3つの並列アルゴリズムをカスタマイズします。 Algorithm 1-3 アルゴリズムの有効/無効を設定します。 設定オプション: [Auto] [Enabled] [Disabled] 次の項目は「Algorithm 1」を [Enabled] に設定した場合にのみ表示されます。 Algorithm 1-3 Condition 監視する条件を選択し、アクションを実行します。複数のアルゴリズムが同じ条件を監 視する場合、結果は 「AND」 となり、2つのアクション値のうち小さい方が書き込まれま す。 設定オプション: [Auto] [CPU Temperature] [Core Voltage] [Core Current] Algorithm 1-3 Action 対象となる条件がしきい値を超えた時に実行するアクションを設定します。複数のアルゴ リズムが同じアクションを実行する場合、結果は 「AND」 となり、2つのアクション値のう ち小さい方が書き込まれます。
CPU Core Voltage CPUコアに供給する電圧の調整方法を設定します。 設定オプション: [Auto] [Manual Mode] [Offset Mode] 次の項目は「CPU Core Voltage」を [Manual Mode] に設定した場合にのみ表示されます。 CPU Core Voltage Override 外部電圧レギュレーターからCPUコアに供給する電圧を設定します。 設定オプション: [Auto] [0.62500] - [1.70000] 次の項目は「CPU Core Voltage」を [Offset Mode] に設定した場合にのみ表示されます。 Offset Mode Sign [+] CPUコア電圧を正の値でオフセットします。 [–] CPUコア電圧を負の値でオフセットします。 CPU Core Voltage Offset CPUコア電圧のオフセット値を設定します。 設定オプション: [Auto] [0.00500] - [0.
Misc Voltage 設定オプション: [Auto] [Offset Mode] 次の項目は「Misc Voltage」を [Offset Mode] に設定した場合にのみ表示されます。 Offset Mode Sign [+] CPUコア電圧を正の値でオフセットします。 [–] CPUコア電圧を負の値でオフセットします。 Misc Voltage Offset 設定オプション: [Auto] [0.01000] - [0.50000] VDDP Voltage 設定オプション: [Auto] [0.70000] - [1.80000] High DRAM Voltage Mode 無効に設定した場合、メモリー電圧の上限は1.435Vになります。有効に設定した場合、メモリー 電圧の上限は2.
SPD HUB VDDIO (1.0V) SPDハブサイドバンドの電源電圧を設定します。 設定オプション: [Auto] [0.90000] - [1.20000] Memory VDD Voltage メモリーICのVDD電源電圧を設定します。 設定オプション: [Auto] [0.80000] - [1.43500] Memory VDDQ Voltage メモリーICのVDDQ電源電圧を設定します。 設定オプション: [Auto] [0.80000] - [1.43500] Memory VPP Voltage メモリーアクティブ化電源の電源電圧を設定します。 設定オプション: [Auto] [1.50000] - [2.13500] Memory Voltage Switching Frequency メモリー電圧レギュレーターのスイッチング周波数をMHz単位で設定します。 設定オプション: [Auto] [0.75000] - [1.50000] Memory Current Capability スイッチングレギュレーターの電流能力をAmp単位で設定します。 設定オプション: [Auto] [0.
6 Advanced CPUやチップセット、オンボードデバイスが備える機能の設定をすることができます。 不適切な設定を行なうと、システムが起動しない、または不安定になるといった症状が出ること があります。設定を変更する際は、専門知識を持った技術者等のアドバイスを受けることを強く お勧めします。 PRIME / ProArt / TUF GAMING AMD 600 Series BIOSガイド 31
6.
Physical Presence Spec Version 使用する物理プレゼンス インターフェイス (PPI) のバージョンを設定します。 設定オプション: [1.2] [1.3] 一部のHCKテストはバージョン 1.3 をサポートしていない場合があります。 6.
6.
L2 Stream HW Prefetcher L2ストリームハードウェアプリフェッチャーの有効/無効を設定します。 設定オプション: [Disable] [Enable] [Auto] L1 Stride Prefetcher 個々の命令のメモリーアクセス履歴を使用し、各アクセスが前と一定の距離にある場合に追 加の行をフェッチする機能の有効/無効を設定します。 設定オプション: [Disable] [Enable] [Auto] L1 Region Prefetcher ある命令のデータアクセスの後に他のデータアクセスが続く傾向がある場合、メモリーアクセ ス履歴を使用して追加の行をフェッチする機能の有効/無効を設定します。 設定オプション: [Disable] [Enable] [Auto] L2 Up/Down Prefetcher メモリーアクセス履歴を使用して、すべてのメモリーアクセスに対して次の行または前の行をフ ェッチするかどうかを決定する機能の有効/無効を設定します。 設定オプション: [Disable] [Enable] [Auto] Core Watchdog Core Watchdog
MCA error thresh enable MCAエラーしきい値の有効/無効を設定します。 設定オプション: [False] [True] [Auto] 次の項目は「MCA error thresh enable」を [True] に設定した場合にのみ表示されます。 MCA error thresh count 有効なエラーしきい値 = 4095(0xFFF) - MCA error thresh count (例: 既定値の0xFF5で は、しきい値は10になります) 設定オプション: [1] - [4095] SMU and PSP Debug Mode この項目が有効に設定されている場合、コールドリセットの原因となるPSP FWまたはSMU FWによって検出された未修正のエラーがハングしシステムは再起動しません。 設定オプション: [Disabled] [Enabled] [Auto] PPIN Opt-in PPIN機能の有効/無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] Fast Short REP MOVSB Fast Short REP MO
次の項目は「SNP Memory (RMP Table) Coverage」を [Custom] に設定した場合にのみ表 示されます。 Amount of Memory to Cover 対象となるシステムメモリーのMBを16進数で指定します。 設定オプション: [0] - [100000] SMEE Secure Memory Encryption (SME) の有効/無効を設定します。 設定オプション: [Disable] [Enable] [Auto] Action on BIST Failure CCD BIST障害が検出された際に実行するアクションを設定します。 設定オプション: [Do nothing] [Down-CCD] [Auto] DF Common Options Memory Addressing Memory interleaving メモリーインターリーブの有効/無効を設定します。 設定オプション: [Disabled] [Auto] Memory interleaving size メモリーインターリーブサイズを設定します。この設定によりインターリーブの開始アドレス (bit
Freeze DF module queues on error エラー発生時にすべてのDFキューをフリーズさせるかどうかを設定します。また、MCAが無 効の場合でも、HWAに同期フラッドを強制します。 設定オプション: [Disabled] [Enabled] [Auto] DF Cstates この項目が有効に設定されている場合、FWはこの機能を有効にするために必要なレジ スタをDF HWにプログラムします。(自動に設定されている場合、このオプションはGlobal C-stateと同期します)。 設定オプション: [Disabled] [Enabled] [Auto] PSP error injection support 設定オプション: [False] [True] UMC Common Options DDR Options DDR Timing Configuration メモリータイミングに関する設定をすることができます。 CPUやメモリーなど各製品の規格や仕様の範囲を超えて使用した場合、保証の対象外となる 場合があります。ご理解の上、自己責任にてご利用ください。 次の項目は「DDR Tim
次の項目は「Trcd Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trcd メモリーの準備ができた後、メモリーの読み取りに要する時間 (tRCD) を 指定します。有効範囲: 0x8 ~ 0x3E。値は16進数です。 Trp Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trp Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trp 新しい行でデータを使用するためにメモリーが準備に要する時間 (tRP) を指定します。有効範囲: 0x8 ~ 0x3E。値は16進数です。 Tras Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Tras Ctrl」を [Manual] に設定した場合にのみ表示されます。 Tras 行がアクティブになりデータへのアクセスが可能になるまでに要する最 小時間 (tRAS) を指定します。有効範囲: 0x1E ~ 0x7E。値は16進数です。 Trc Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trc C
Trfc2 Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trfc2 Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trfc2 リフレッシュ後、再度リフレッシュが可能になるまでに要する時間 (tRFC2) を指定します。有効範囲: 0x32 ~ 0xFFF。値は16進数です。 TrfcSb Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TrfcSb Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrfcSb リフレッシュ後、再度リフレッシュが可能になるまでに要する時間 (tRFCsb) を指定します。有効範囲: 0x32 ~ 0x7FF。値は16進数です。 DDR Non-SPD Timing Trtp Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trtp Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trtp 読み出しからプリチャージまでに要する時間 (tRTP) を指定します。有効 範囲: 0x5 ~
次の項目は「Tfaw Ctrl」を [Manual] に設定した場合にのみ表示されます。 Tfaw 4つのバンクのみをアクティブにできる時間 (tFAW) を指定します。有効範 囲: 0x14 ~ 0x50。値は16進数です。 TwtrL Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TwtrL Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwtrL 同じメモリーバンクグループにおける最小書き込みから読み出しに要する 時間 (tWTR_L) を指定します。有効範囲: 0x8 ~ 0x30。値は16進数です。 TwtrS Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TwtrS Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwtrS 異なるメモリーバンクグループにおける最小書き込みから読み出しに要 する時間 (tWTR_S) を指定します。有効範囲: 0x2 ~ 0x10。値は16進数で す。 TrdrdScL Ctrl [Auto] 既定の設定に従う [Manual]
TrdrdDd Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TrdrdDd Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrdrdDd 異なるDIMM上の異なるチップセレクトにおける読み取りから次の読み取 りまでに要する時間 (tRDRDd) を指定します。有効範囲: 0x1 ~ 0xF。値は 16進数です。 TwrwrScL Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「TwrwrScL Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwrwrScL 同じメモリーバンクグループにおける書き込みから次の書き込みまでに 要する時間 (tWRWRScL) を指定します。有効範囲: 0x1 ~ 0x3F。値は16進 数です。 TwrwrSc Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「TwrwrSc Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwrwrSc 同じDIMM上の同じチップセレクトにおける書き込みから次
次の項目は「Twrrd Ctrl」を [Manual] に設定した場合にのみ表示されます。 Twrrd 同じメモリーランクにおける書き込みから次の読み取りまでに要する時 間 (tWRRD) を指定します。有効範囲: 0x1 ~ 0xF。値は16進数です。 Trdwr Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「Trdwr Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trdwr 同じメモリーランクにおける読み取りから次の書き込みまでに要する時 間 (tRDWR) を指定します。有効範囲: 0x1 ~ 0xF。値は16進数です。 DDR BUS Configuration メモリーバスに関するを設定をすることができます。 Processor CK drive strengths プロセッサーCKドライブ強度を指定します。 設定オプション: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.
DRAM DQ drive strengths DRAM DQドライブ強度を指定します。 設定オプション: [Auto] [48 ohm] [40 ohm] [34 ohm] DDR Controller Configuration メモリーコントローラーに関する設定をすることができます。 DDR Power Options Power Down Enable 非アクティブ時にDRAMを休止状態にするDRAM Power Downの有効/ 無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] DDR RAS メモリーRAS機能に関する設定をすることができます。 Disable Memory Error Injection 設定オプション: [False] [True] [Auto] DDR ECC Configuration DDR Security メモリーセキュリティに関する設定をすることができます。 TSME 設定オプション: [Auto] [Enabled] [Disabled] Data Scramble 設定オプション: [Enabled] [Disab
次の項目は「MBIST Enable」を [Enabled] に設定した場合にのみ表示されます。 MBIST Test Mode MBISTのテストモードを設定します。Interface Modeは単一および複数のCSトラ ンザクションと基本的な接続性をテストし、Data Eye Modeは電圧とタイミングを 測定します。 設定オプション: [Interface Mode] [Data Eye Mode] [Both] [Auto] MBIST Aggressors メモリーアグレッサーテストの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] MBIST Per Bit Slave Die Reporting 各DQ、チップセレクト、チャンネルのABLログに2D Data Eye Resultsをレポートす る機能の有効/無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] DDR Data Eye Pattern Select 設定オプション: [PRBS] [SSO] [Both] Pattern Length
GPU Host Translation Cache GPUホスト変換キャッシュの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] Audio Configuration オーディオに関する設定をすることができます。 NB Azalia 内蔵HDオーディオコントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] [Auto] Audio IOs 設定オプション: [Auto] [HDA(3SDI) + PDM(2CH)(Default)] [HDA (1SDI) + PDM(6CH)] [HDA(1SDI) + SW0(1MDATA) + PDM(2CH)] [SW0(4MDATA) + PDM(6CH)] [SW0(4MDATA) + SW1(1MDATA) + PDM(2CH)] PCIe loopback Mode PCIeループバックモードの有効/無効を設定します。 設定オプション: [Auto] [Disabled] [Enabled] SMU Common Options TDP Control [Au
EDC Control [Auto] [Manual] 既定のEDC上限 (Electrical Design Current Limit) を使用します。 カスタマイズされたEDC上限を使用します。 次の項目は「EDC Control」を [Manual] に設定した場合にのみ表示されます。 TDC_VDDCR_VDD VDDCR_VDD EDC上限 [mA] を設定します。(IRM制限が適用されます) PROCHOT Control [Auto] 既定のPROCHOTデアサーションランプタイムを使用します。 [Manual] カスタマイズされたPROCHOTデアサーションランプタイムを使用しま す。 次の項目は「PROCHOT Control」を [Manual] に設定した場合にのみ表示されます。 PROCHOT Deassertion Ramp Time PROCHOTデアサーションランプタイム [ms] を設定します。(IRM制限が適用されます) Fan Control [Auto] [Manual] 既定のファンコントローラー設定を使用します。 カスタマイズされたファンコントロ
PWM Frequency [Auto] 既定値 [1] 100Hz [0] 25kHz Fan Polarity [Auto] 既定値 [1] 正 [0] 負 VDDP Voltage Control [Auto] 既定のVDDP電圧を使用します。 [Manual] カスタマイズされたVDDP電圧を使用します。 次の項目は「VDDP Voltage Control」を [Manual] に設定した場合にのみ表示されます。 VDDP Voltage ターゲットVDDP電圧 [mV] を設定します。 設定オプション: [0] - [2000] Infinity Fabric Frequency and Dividers 設定オプション: [Auto] [100 MHz] - [1066 MHz] FEATURE FCLK DPM 設定オプション: [Auto] [Disabled] [Enabled] SyncFifo Mode Override 設定オプション: [Disable] [Enable] [Auto] 48 PRIME / ProArt / TUF GAMING AMD 600 Serie
6.
6.
6.
USB Single Port Control USBポートの個別制御に関する設定をすることができます。 表示される内容はお使いの製品により異なります。 6.7 Network Stack Configuration UEFIネットワークスタックに関する設定をすることができます。 Network stack UEFIネットワークスタックの有効/無効を設定します。 設定オプション: [Disable] [Enable] 次の項目は「Network Stack」を [Enabled] に設定した場合にのみ表示されます。 Ipv4/Ipv6 PXE Support IPv4/IPv6プロトコルによるPXEネットワークブートの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] 6.
6.9 HDD/SSD SMART Information SATAポートに接続されたストレージデバイスのS.M.A.R.T.情報を表示します。 表示される内容はお使いの製品により異なります。 NVM ExpressデバイスのS.M.A.R.T.
6.10 SATA Configuration チップセットのSATAコントローラーに関する設定をすることができます。SATAポートにSATAデバ イスが取り付けられていない場合、ポート名の横には「Empty」 と表示されます。 SATA Controller(s) SATAコントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] 次の項目は「SATA Controller(s)」を [Enabled] に設定した場合にのみ表示されます。 SATA Mode SATAコントローラーの動作モードを設定します。 [AHCI] AHCI (Advanced Host Controller Interface) モードで動作します。 [RAID] RAID (Redundant Arrays of Inexpensive Disks) モードで動作します。 複数のSATAデバイスを使用してRAIDアレイを構築することができま す。 NVMe RAID Mode PCIe M.
SATA6G_1 - SATA6G_4 SATA 6Gb/sポートに接続したSATAデバイスが表示されます。 設定オプション: [Disabled] [Enabled] SATA6G_1 - SATA6G_4 Hot Plug SATAポートのホットプラグ機能の有効/無効を設定します。 設定オプション: [Disabled] [Enabled] 6.
6.12 Onboard Devices Configuration オンボードデバイスに関する設定をすることができます。 この画面に表示される項目は、ご使用のマザーボードにより異なります。 PCIEX16_1 Bandwidth Bifurcation Configuration [Auto Mode] 装着されたデバイスを検出し動作モードを自動で切り替えます。 PCIEX16_2スロットに拡張カードが取り付けられた場合、PCIEX16_1 スロットはx8モードで動作します。PCIEX16_2スロットに拡張カード が取り付けられていない場合、PCIEX16_1スロットはx16モードで動 作します。 [PCIE X16 Mode] PCIEX16_1スロットはx16モードで動作します。PCIEX16_2スロット は無効です。 [PCIE RAID Mode] HYPER M.2 X16 CARDに装着された複数のM.2 SSDを検出すること が可能になります。 HYPER M.2 X16 CARDまたはその他のM.
HD Audio Controller HDオーディオコントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] Wi-Fi Controller Wi-Fiコントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] Bluetooth Controller Bluetooth® コントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] LED lighting When system is in working state システム動作中のLEDの点灯方法を設定します。 [All On] すべてのLEDはオン [Stealth Mode] すべてのLEDはオフ [Aura Only] Aura対応RGB LEDのみオン、機能LEDはオフ [Aura Off] Aura対応RGB LEDのみオフ、機能LEDはオン 各種LEDの有無はお使いの製品により異なります。 When system is in sleep, hibernate or soft off sta
10G LAN Card 10G LANコントローラーの有効/無効を設定します。 設定オプション: [Disabled] [Enabled] USB power delivery in Soft Off state (S5) S5 電源オフ状態のUSB電源供給機能の有効/無効を設定します。 設定オプション: [Disabled] [Enabled] Serial Port Configuration シリアルポート (COM) に関する設定をすることができます。 本項目は、ご使用のマザーボードにシリアルポートコネクター (COM) が搭載されている場合に のみ表示されます。 Serial Port シリアルポート (COM) の有効/無効を設定します。 設定オプション: [Enabled] [Disabled] 次の項目は「Serial Port」を [Enabled] に設定した場合にのみ表示されます。 Change settings スーパーI/Oデバイスに最適な設定を選択します。 設定オプション: [IO=3F8h; IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4
Chipset_2 Link Mode Chipset_1とChipset_2間のリンク速度を設定します。 設定オプション: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] M.2_3 Link Mode M.2_3 スロットのリンク速度を設定します。 設定オプション: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] PCIEX16 Link Mode PCIEX16 スロットのリンク速度を設定します。 設定オプション: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] 6.
6.
Discrete GPU HPD Circuitry ディスクリートGPUディスプレイHPD回路の有効/無効を設定します。 設定オプション: [OR Circuitry] [Pulse Circuitry] Discrete GPU’s Audio ディスクリートGPUのオーディオの有効/無効を設定します。 設定オプション: [Disabled] [Keep ROM Strap Setting] Discrete GPU’s USB Port ディスクリートGPUのUSBポートの有効/無効を設定します。 設定オプション: [Keep Default Setting] [Disabled] Discrete GPU’s SSID/SVID プログラムディスクリートGPUのSSID/SVIDは、 Hybrid Graphicsの設定に依存します。 設定オプション: [Keep Default Setting] [Program by Vendor] Discrete GPU BOMACO Support ディスクリートGPU BOMACOサポートの有効/無効を設定します。 設定オプション: [Disabled]
6.
SMT Control 同時マルチスレッド (SMT) を無効にする際に使用します。SMTを再び有効にするには、自動 を選択した後パワーサイクル (電源の入れ直し) が必要です。 設定オプション: [Auto] [Disable] SMTが無効に設定されているシステムでは、S3はサポートされません。 DDR and Infinity Fabric Frequency/Timings DDR Options DDR Timing Configuration Active Memory Timing Settings 設定オプション: [Auto] [Enabled] 次の項目は「Active Memory Timing Settings」を [Enabled] に設定した場合にのみ表示さ れます。 Memory Target Speed メモリーターゲット速度を設定します。 DDR SPD Timing Tcl Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Tcl Ctrl」を [Manual] に設定した場合にのみ表示されます。 Tcl メモリーモジュールがメモ
Tras Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Tras Ctrl」を [Manual] に設定した場合にのみ表示されます。 Tras 行がアクティブになりデータへのアクセスが可能になるまでに要する最 小時間 (tRAS) を指定します。有効範囲: 0x1E ~ 0x7E。値は16進数です。 Trc Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trc Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trc 行がアクティブになりリフレッシュされるまでに要する時間 (tRC)を指定 します。有効範囲: 0x20 ~ 0xFF。値は16進数です。 Twr Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Twr Ctrl」を [Manual] に設定した場合にのみ表示されます。 Twr 最小書き込み回復時間 (tWR) を指定します。有効範囲: 0x30 ~ 0x60。値 は16進数です。 Trfc1 Ctrl [Auto] [Manual] 既定の設
次の項目は「TrfcSb Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrfcSb リフレッシュ後、再度リフレッシュが可能になるまでに要する時間 (tRFCsb) を指定します。有効範囲: 0x32 ~ 0x7FF。値は16進数です。 Trtp Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「Trtp Ctrl」を [Manual] に設定した場合にのみ表示されます。 Trtp 読み出しからプリチャージまでに要する時間 (tRTP) を指定します。有効 範囲: 0x5 ~ 0x1F。値は16進数です。 TrrdL Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TrrdL Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrrdL 同じメモリーパンクグループにおけるアクティブバンクからアクティブバン クまでに要する時間 (tRRD_L) を指定します。有効範囲: 0x4 ~ 0x20。値 は16進数です。 TrrdS Ctrl [Auto] [Manual] 既定の設定に従
TwtrS Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TwtrS Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwtrS 異なるメモリーバンクグループにおける最小書き込みから読み出しに要 する時間 (tWTR_S) を指定します。有効範囲: 0x2 ~ 0x10。値は16進数で す。 DDR Non-SPD Timing TrdrdScL Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「TrdrdScL Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrdrdScL 同じメモリーバンクグループにおける読み取りから次の読み取りまでに要 する時間 (tRDRDSc_L) を指定します。有効範囲: 0x1 ~ 0xF。値は16進数 です。 TrdrdSc Ctrl [Auto] [Manual] 既定の設定に従う 手動で指定 次の項目は「TrdrdSc Ctrl」を [Manual] に設定した場合にのみ表示されます。 TrdrdSc 同じDIMM上の同じチップセレクトにお
次の項目は「TwrwrScL Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwrwrScL 同じメモリーバンクグループにおける書き込みから次の書き込みまでに 要する時間 (tWRWRScL) を指定します。有効範囲: 0x1 ~ 0x3F。値は16進 数です。 TwrwrSc Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「TwrwrSc Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwrwrSc 同じDIMM上の同じチップセレクトにおける書き込みから次の書き込みま でに要する時間 (tWRWRSc) を指定します。有効範囲: 0x1 ~ 0xF。値は16 進数です。 TwrwrSd Ctrl [Auto] 既定の設定に従う [Manual] 手動で指定 次の項目は「TwrwrSd Ctrl」を [Manual] に設定した場合にのみ表示されます。 TwrwrSd 同じDIMM上の異なるチップセレクトにおける書き込みから次の書き込み までに要する時間 (tWRWRSd) を指定します。有効範囲: 0x1 ~ 0xF
DDR BUS Configuration Processor CA drive strengths プロセッサーCAドライブ強度を指定します。 設定オプション: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0 Ohm] Processor DQ drive strengths プロセッサーDQドライブ強度を指定します。 設定オプション: [Auto] [High Impedance] [240 ohm] [120 ohm] [80 ohm] [60 ohm] [48 ohm] [40 ohm] [34.3 ohm] Processor ODT impedance プロセッサーODTインピーダンスを指定します。 設定オプション: [Auto] [High Impedance] [480 ohm] [240 ohm] [160 ohm] [120 ohm] [96 ohm] [80 ohm] [68.
Precision Boost Overdrive Precision Boost Overdrive PPT、VDD_CPU EDC、VDD_CPU TDC、VDD_SOC EDC、VDD_SOC TDCの定義された値を 超えてプロセッサーをボードの限界まで動作させ、デフォルトよりも長い時間、より高い電 圧でブースト動作させる機能の設定をします。 設定オプション: [Auto] [Disabled] [Enabled] [Manual] 次の項目は「Precision Boost Overdrive」を [Manual] に設定した場合にのみ表示されま す。 PBO Limits [Auto] AMD既定のPackage Power Tracking (PTT)、Electrical Design Current (EDC)、Thermal Design Current (TDC) を読み込みます。 [Disable] PBO上限を無効にします。 [Motherboard] マザーボードで設定されているPPT、EDC、TDC上限に従いプロセッサー を動作させます。 [Manual] PPT、EDC
次の項目は「CPU Boost Clock Override」を [Enabled (Positive)] に設定した場合にのみ表 示されます。 Max CPU Boost Clock Override(+) Precision Boost 2アルゴリズムによって目標とされる最大CPU周波数を増加させます。 設定オプション: [Auto] [0] - [200] 次の項目は「CPU Boost Clock Override」を [Enabled (Negative)] に設定した場合にのみ 表示されます。 Max CPU Boost Clock Override(-) Precision Boost 2アルゴリズムによって自動的に達成される最大CPU周波数を減少させ ます。 設定オプション: [Auto] [0] - [200] Platform Thermal Throttle Ctrl プロセッサーの最大許容温度 (摂氏) を設定します。 設定オプション: [Manual] [Auto] 次の項目は「Platform Thermal Throttle Ctrl」を [Manual] に設定した場合にの
Curve Optimizer Curve Optimizer すべてのコアまたは特定のコアのAVFSカーブを調整し、カーブを上書きすることでCPUのパ フォーマンスを向上させることができます。大きい値を設定することで、電圧上限は高くなり ます。 設定オプション: [Disable] [All Cores] [Per Core] 次の項目は「Curve Optimizer」を [All Cores] に設定した場合にのみ表示されます。 All Core Curve Optimizer Sign すべてのコアのAVFSカーブのシフト方向を設定します。Positiveに設定するとカーブは上にシ フトし高い電圧使用することができるようになり、Negativeに設定するとカーブは下にシフト し低い電圧を使用することができるようになります。 設定オプション: [Positive] [Negative] All Core Curve Optimizer Magnitude カーブシフトの大きさを整数で設定します。値が大きいほどシフトの大きさは大きくなりま す。 設定オプション: [0] - [30] 次の項目は「Curv
VDDP Voltage Control VDDP Voltage Control VDDP電圧の調整方法を設定します。 [Auto] VDDPはシステムの既定値です。 [Manual] DDRバス信号 (PHY) 電圧を設定します。 次の項目は「VDDG Voltage Control」を [Manual] に設定した場合にのみ表示されます。 VDDP Voltage Adjust VDDPはDDRバス信号 (PHY) 電圧で、DRAM電圧 (VDDIO_Mem) から派生しています。そ のため、VDDP電圧はmV単位でDRAM電圧に近づけることはできますが、超えることはで きません。 設定オプション: [0] - [2000] SoC/Uncore OC Mode SoC/Uncore OC Mode Infinity Fabric、メモリー、内蔵グラフィックスなどのCPU SoC/アンコアコンポーネントを 常に指定された最大周波数で実行するように強制します。アイドル時の電力を節約する代 わりに、パフォーマンスを向上させることができます。 設定オプション: [Auto] [Enabled] [Disa
LCLK Frequency Control LCLK Frequency Control [Auto] 既定値を使用します。 [Manual] LCLK周波数を手動で設定します。 次の項目は「LCLK Frequency Control」を [Manual] に設定した場合にのみ表示されます。 Maximum Frequency LCLK最大周波数を設定します。 設定オプション: [1029] - [2500] Onboard Voltage Control VDDIO Voltage Control VDDIO Ctrl VDDIO電圧を設定します。 [Auto] 既定のVDDIO電圧を使用します。 [Manual] DIMM VDD/VDDQをAPU VDDIOに同期するように設定します。 [Separate] APU VDDIO、DIMM VDD/VDDQを独立制御します。 Running VDDQ != VDD は非標準であり,メモリーの安定性問題を引き起こす可能性があり ます。ランプダウンおよびランプアップ時には、VDDQ-VDD電圧は200mV未満にする必要が あります。 次の
次の項目は「VPP Ctrl」を [Manual] に設定した場合にのみ表示されます。 VPP Adjust MEM VPPを調整します。 設定オプション: [1500] - [2135] 74 PRIME / ProArt / TUF GAMING AMD 600 Series BIOSガイド
7 Monitor システムの温度、電源状態、ファン回転数を確認することができます。また、この項目では取り付け られたファンの制御を行なうことができます。 Temperature Monitor CPU Temperature, CPU Package Temperature, MotherBoard Temperature, VRM Temperature, Chipset 1-2 Temperature, T_Sensor Temperature, DIMM A1-2 Temperature, DIMM B1-2 Temperature [xxx°C/xxx°F] システムの温度を自動検出し摂氏/華氏で表示します。温度の検出を停止する場合は [Ignore]に設定します。 Fan Speed Monitor CPU Fan Speed, CPU Optional Fan Speed, Chassis Fan 1-5 Speed, AIO PUMP Speed [xxxx RPM] 各ファンの回転数を自動検出し、RPM単位で表示します。マザーボードにファンが接続さ れていない場合は、[N/A] と表
Voltage Monitor CPU Core Voltage, 12V Voltage, 5V Voltage, 3.3V Voltage, CPU VDDIO / MC Voltage [x.
CPU Fan Speed Low Limit CPUファン/ポンプの下限回転数を設定します。設定された回転数を下回るとシステム起 動時に警告メッセージが表示されます。[Ignore] に設定すると警告メッセージは表示され ません。 設定オプション: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] 次の項目は「CPU Fan Profile」を [Manual] に設定した場合にのみ表示されます。 CPU Fan Point4 Temperature 熱源温度がポイント4温度より低い場合、デューティサイクルはポイント3-ポイント4および 熱源温度に基づいて決定されます。熱源温度がポイント4温度より高い場合、ファン/ポン プはポイント4デューティサイクルで動作します。 CPU Fan Point4 Duty Cycle (%) 熱源温度がポイント4温度より低い場合、デューティサイクルはポイント3-ポイント4および 熱源温度に基づいて決定されます。熱源温度がポイント4温度より高い場合、ファン/ポン プはポイント4デューティサイクルで動作します
CPU Fan Point1 Temperature 熱源温度がポイント1温度より低い場合、ファン/ポンプはポイント1デューティサイクルで動 作します。熱源温度がポイント1温度より高い場合、デューティサイクルはポイント1-ポイン ト2および熱源温度に基づいて決定されます。 CPU Fan Point1 Duty Cycle (%) 熱源温度がポイント1温度より低い場合、ファン/ポンプはポイント1デューティサイクルで動 作します。熱源温度がポイント1温度より高い場合、デューティサイクルはポイント1-ポイン ト2および熱源温度に基づいて決定されます。 Chassis Fan(s) Configuration Chassis Fan 1-5 Q-Fan Control ケースファンの制御方法を選択します。 [Auto Detect] 接続されているファンのモードを検出し自動的に制御モードを 変更します。 [DC Mode] ファンをDCモードで制御します。 [PWM Mode] 4ピン接続のファンをPWMモードで制御します。 Chassis Fan 1-5 Profile ケースファンの動作プロファイル
次の項目は「Chassis Fan 1-5 Profile」を [Manual] に設定した場合にのみ表示されます。 Chassis Fan 1-5 Point4 Temperature 熱源温度がポイント4温度より低い場合、デューティサイクルはポイント3-ポイント4および熱 源温度に基づいて決定されます。熱源温度がポイント4温度より高い場合、ファン/ポンプはポ イント4デューティサイクルで動作します。 Chassis Fan 1-5 Point4 Duty Cycle (%) 熱源温度がポイント4温度より低い場合、デューティサイクルはポイント3-ポイント4および熱 源温度に基づいて決定されます。熱源温度がポイント4温度より高い場合、ファン/ポンプはポ イント4デューティサイクルで動作します。 Chassis Fan 1-5 Point3 Temperature 熱源温度がポイント3温度より低い場合、デューティサイクルはポイント2-ポイント3および熱 源温度に基づいて決定されます。熱源温度がポイント3温度より高い場合、デューティサイク ルはポイント3-ポイント4および熱源温度に基づいて決定されます。 Chas
AIO Pump Q-Fan Control オールインワン水冷クーラーポンプの制御方法を選択します。 [Auto Detect] 接続されているポンプのモードを検出し自動的に制御モードを変更 します。 [DC Mode] ポンプをDCモードで制御します。 [PWM Mode] 4ピン接続のポンプをPWMモードで制御します。 AIO Pump Profile オールインワン水冷クーラーポンプの動作プロファイルを設定します。[Manual] に設定し た際にCPU温度が75℃を超える場合は、各デューティサイクルを100%に設定することをお 勧めします。デューティサイクル効率が悪い場合、オーバーヒートによってCPUのパフォー マンスが低下します。 設定オプション: [Standard] [Silent] [Turbo] [Full Speed] [Manual] 次の項目は「AIO Pump Profile」を [Standard] [Turbo] [Manual] のいずれかに設定した場 合に表示されます。 AIO Pump Q-Fan Source オールインワン水冷クーラーポンプを制御するため
AIO Pump Point4 Duty Cycle (%) 熱源温度がポイント4温度より低い場合、デューティサイクルはポイント3-ポイント4および 熱源温度に基づいて決定されます。熱源温度がポイント4温度より高い場合、ポンプはポ イント4デューティサイクルで動作します。 AIO Pump Point3 Temperature 熱源温度がポイント3温度より低い場合、デューティサイクルはポイント2-ポイント3および 熱源温度に基づいて決定されます。熱源温度がポイント3温度より高い場合、デューティサ イクルはポイント3-ポイント4および熱源温度に基づいて決定されます。 AIO Pump Point3 Duty Cycle (%) 熱源温度がポイント3温度より低い場合、デューティサイクルはポイント2-ポイント3および 熱源温度に基づいて決定されます。熱源温度がポイント3温度より高い場合、デューティサ イクルはポイント3-ポイント4および熱源温度に基づいて決定されます。 AIO Pump Point2 Temperature 熱源温度がポイント2温度より低い場合、デューティサイクルはポイント1-ポイント2および 熱源
8 Boot システム起動に関する設定を行うことができます。 CSM (Compatibility Support Module) CSM (Compatibility Support Module)のパラメータ設定です。この設定によってUEFIドライバー を持たないデバイスとの互換性を向上させることが可能です。 CPU内蔵グラフィックスを使用する場合、Launch CSMは [Disabled] に設定され変更するこ とはできません。 Launch CSM [Enabled] 互換性を高めるために、CSMが非UEFIドライバーアドオンデバイスま たはWindows ® UEFIモードを完全にサポートできるようにします。 [Disabled] CSMを無効にして、Windows® セキュアアップデートとセキュアブー トを完全にサポートできるようにします。 次の項目は「Launch CSM」を [Enabled] に設定した場合にのみ表示されます。 Boot Device Control 起動を許可するデバイスタイプを選択します。選択したモードのデバイスのみがブート優先順 位リストに表示されます。
Boot from Storage Devices 起動を許可するストレージデバイスのモードを選択します。[Ignore] に設定した場合、POST 時にストレージデバイスは検出されず起動時間を短縮することができます。 設定オプション: [Ignore] [Legacy only] [UEFI only] Boot from PCI-E/PCI Expansion Devices 起動を許可するPCI-E/PCI拡張デバイスのモードを選択します。[Ignore] に設定した場 合、POST時にPCI-E/PCI拡張デバイスは検出されず起動時間を短縮することができます。 設定オプション: [Ignore] [Legacy only] [UEFI only] Secure Boot システム起動時に許可されていないファームウェア、オペレーティングシステム、UEFIドライバー (オプションROM)が実行されないようにするWindows® Secure Bootに関する設定をすること ができます。 OS Type [Windows UEFI Mode] セキュアブートによる署名チェックを実行します。Windows
Set New key USBストレージデバイスからPKを読み込みます。 Delete key PKを削除します。 PKを削除した場合、Secure Bootは利用できません。 設定オプション: [Yes] [No] ロードするファイルは時間ベース認証変数を使用するUEFI可変構造でフォーマットされている 必要があります。 KEK Management KEK(キー交換キーデータベース、またはキー登録キーデータベース)は、署名データベース (db) と失効した署名データベース (dbx) の更新に使用されます。 キー交換キーデータベース (KEK) はWindows® Secure Boot キー登録キーデータベース (KEK) を示します。 Save to file KEKをUSBストレージデバイスに保存します。 Set New key USBストレージデバイスからKEKを読み込みます。 Append Key システムにKEKを追加します。 Delete key KEK を削除します。 設定オプション: [Yes] [No] ロードするファイルは時間ベース認証変数を使用するUEFI可変構造でフォーマットさ
DBX Management 失効した署名データベース (dbx) は、信頼されなくなったために読み込みが許可されない アイテムの、失効したイメージが登録されています。 Save to file dbxをUSBストレージデバイスに保存します。 Set New key USBストレージデバイスからdbxを読み込みます。 Append Key システムにdbxを追加します。 Delete key dbx を削除します。 設定オプション: [Yes] [No] ロードするファイルは時間ベース認証変数を使用するUEFI可変構造でフォーマットされている 必要があります。 Boot Configuration Fast Boot システムを起動するために必要な最小限のデバイスのみを初期化しシステムを素早く起動で きるようにするFast Boot機能の有効/無効を設定します。BIOS Boot Specification (BBS) ブー トオプションには無効です。 設定オプション:[Disabled] [Enabled] 次の項目は、 「Fast Boot」を [Enabled] に設定した場合にのみ表示されます。
次の項目は「Boot Logo Display」を [Disabled] に設定した場合にのみ表示されます。 Post Report POST画面を表示する時間を設定します。 設定オプション: [1 sec] - [10 sec] [Until Press ESC] Boot up NumLock State システム起動時のNumLockキーの有効/無効を設定します。 設定オプション: [On] [Off] Wait For ‘F1’ If Error POST実行中にエラーが発生した場合、F1 キーを押すまでシステムを待機させる機能の有 効/無効を設定します。 設定オプション: [Disabled] [Enabled] Option ROM Messages [Force BIOS] オプションROMメッセージをPOST中に表示します。 [Keep Current] オプションROMメッセージをPOST中に表示しません。 Interrupt 19 Capture サービス割り込み信号 INT 0x19命令の有効/無効を設定します。複数の拡張カードにオプ ションROMが搭載されている場合は[Enable
9 Tool ASUS独自機能を設定することができます。 BIOS Image Rollback Support BIOSイメージロールバックサポートの有効/無効を設定します。 [Enabled] BIOSを以前のバージョンにロールバックすることを可能にしますが、この設定 はNIST SP 800-147の要件に違反します。 [Disabled] BIOSを新しいバージョンにのみアップデートすることができます。この設定は NIST SP 800-147の要件を満たしています。 Publish HII Resources 設定オプション: [Disabled] [Enabled] Flexkey Fkexkeyボタンの動作を設定します。 [Reset] システムを強制的に再起動します。保存されていない作業中のデータは削除 されます。 [Aura On/Off] Aura LEDをオン/オフします。この動作は他のBIOS/アプリケーションソフトウ ェア設定と同期されません。 [DirectKey] UEFI BIOS Utilityを直接起動します。 Setup Animator UEFI
9.1 ASUS EZ Flash 3 Utility UEFI BIOS更新ツール「ASUS EZ Flash 3 Utility」を起動します。このユーティリティはカーソル キーとを使用して操作します。 詳細は「11.1 ASUS EZ Flash 3 Utility」をご参照ください。 9.
9.
9.4 ASUS SPD Information メモリースロットに装着されたメモリーモジュールのSPD (Serial Presence Detect) 情報を読み出 して表示します。 9.
9.
10 Exit 設定の保存や取り消しのほか、既定値の読み込みを行なうことができます。 Load Optimized Defaults UEFI BIOS Utilityのパラメーターの既定値を読み込みます。を押すことで同じ動作を行なう ことができます。 Save Changes & Reset 変更した設定を保存してUEFI BIOS Utilityを終了します。を押すことで同じ動作を行なう ことができます。 Discard Changes & Exit 変更した設定を保存せずにUEFI BIOS Utilityを終了します。 Launch EFI Shell from USB drives EFI Shellを起動するためのファイル (Shellx64.
11 UEFI BIOSの更新 ASUS Webサイトでは、システムの安定性、互換性、パフォーマンスの改善、機能拡張などを提要 するために最新のBIOSイメージを公開しています。ただし、UEFI BIOSの更新にはリスクが伴いま す。現在のバージョンで問題がない場合は、UEFI BIOSの更新を行わないでください。不適切な 更新は、システム起動エラーの原因となります。更新は必要な場合のみ行ない、更新の際は次の 手順に従い慎重に行なってください。 最新のBIOSイメージファイルは、ASUS Webサイト(https://www.asus.com)からダウンロード することができます。 次の機能を使用してUEFI BIOSの更新と管理を行なうことができます。 1. ASUS EZ Flash 3 Utility: USBストレージデバイスを使用してUEFI BIOS UtilityからUEFI BIOSを 更新することができます。 2.
11.1 ASUS EZ Flash 3 Utility ASUS EZ Flash 3 Utility は、OSベースのユーティリティを起動することなくUEFI BIOSを短時間で 更新することができます。 安全性及び信頼性を確保するため、Load Optimized Defaults を実行しUEFI BIOSの設定を 既定値に戻してから更新を行なってください。 UEFI BIOSを更新する: 94 • 安全性及び信頼性を確保するため、FAT32/16 ファイルシステムでフォーマットされたシ ングルパーティションのUSBストレージデバイスなどをご使用ください。 • UEFI BIOSの更新中にシステムのシャットダウンやリセットを行わないでください。UEFI BIOSが破損、損傷しシステムを起動することができなくなる恐れがあります。UEFI BIOS の更新に伴う不具合、動作不良、破損等に関しましては保証の対象外となります。 1. BIOSイメージファイルを保存したUSBストレージデバイスをシステムのUSBポートに接続し ます。 2.
11.2 ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 はUEFI BIOSを復元することができるツールです。更新時などに破損した UEFI BIOSをUSBストレージデバイスを使用して復元することができます。 製品固有のファイル名については、BIOSリネームツール「BIOSRenamer」を使用するか、また は各マザーボードのユーザーガイドをご確認ください。 UEFI BIOSを復元する 手順 1. 最新のBIOSイメージファイルを、ASUSオフィシャルサイト(https://www.asus.com)から ダウンロードし、ダウンロードしたファイルを展開します。 2. ダウンロードしたBIOSイメージファイルの名前を「ASUS.CAP」または製品固有のふぁいる 名に変更し、USBストレージデバイスのルートディレクトリにコピーします。 3. BIOSイメージファイルが保存されたUSBストレージデバイスを復元するシステムのUSBポー トに接続します。 4. システムの電源をオンにします。 5.