BIOS 使用手冊 Motherboard PRIME / ProArt / TUF GAMING AMD 600 系列
T21968 第三版 2023 年 4 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 1. 2. 認識 BIOS 程式................................................................................................................ 4 BIOS 程式設定.................................................................................................................. 5 2.1 EZ Mode.......................................................................................................... 6 2.2 進階模式(Advanced Mode)................................................................ 7 2.3 Qfan Control....................
BIOS 程式設定 1.
2.
2.
2.
功能表列 BIOS 設定程式最上方各選單功能說明如下: My Favorites 本項目將記錄時常使用的系統設定及設定值。 Main 本項目提供系統基本設定。 Ai Tweaker 本項目提供超頻設定。 Advanced 本項目提供系統進階功能設定。 Monitor 本項目提供溫度、電源及風扇功能設定。 Boot 本項目提供開機磁碟設定。 Tool 本項目提供特殊功能設定。 Exit 本項目提供離開 BIOS 設定程式與出廠預設值還原功能。 選單項目 於功能表列選定選項時,被選擇的功能將會反白,即選擇 Main 選單所出現的項目。 點選選單中的其他項目(例如:My Favories、Ai Tweaker、Advanced、Monitor、Boot、Tool 與 Exit)也會出現該項目不同的選項。 子選單 在選單畫面中,若功能選項前面有一個小三角形標記(>),代表此為子選單,您可 利用方向鍵來選擇,並按下 鍵來進入子選單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程式介面顯示的語言。點選這個按鈕 來選擇您想要的 BIOS 畫面顯示語言。 我的
AURA(F4) 這個按鈕用來啟動或關閉 RGB LED 功能。您可以按下 鍵開啟此選單。 [All On] 啟動所有的 LED 指示燈(Aura 特效或是功能性指示燈)。 [Stealth Mode] 關閉所有的 LED 指示燈(Aura 特效與功能性指示燈)。 [Aura Only] 啟動 Aura 特效,而功能性指示燈將會關閉。 [Aura Off] 關閉 Aura 特效,而功能性指示燈依舊為開啟狀態。 ReSize BAR 這個按鈕用來啟動或關閉 ReSize BAR 功能。 [On] 啟動 ReSize BAR 支援以充分利用 GPU 記憶體。CSM(相容性支援 模組)將會關閉。 [Off] 關閉 ReSize BAR 支援。 快速鍵 這個按鈕位在功能表列的上方,包含有 BIOS 程式設定的導引方向鍵,使用箭頭按鍵 來選擇選單中的項目並變更設定。 捲軸 在選單畫面的右方若出現捲軸,即代表此頁選項超過可顯示的畫面,您可利用上/下 方向鍵或是 PageUp/PageDown 鍵來切換畫面。 線上操作說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項
2.
手動設定風扇 從設定檔清單中選擇 Manual 來手動設定風扇運作的速度。 速度點 點選或輕觸以手動設定風扇 請依照以下步驟設定風扇: 1. 選擇想要設定的風扇並查看該風扇現在的狀況。 2. 點選並拖曳速度點來調整風扇的運作速度。 3.
3.
新增項目至我的最愛 請依照以下步驟新增項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程式畫面中點選 MyFavorite 來啟動設定樹狀圖 畫面。 2. 在設定樹狀圖畫面中選擇想要儲存至我的最愛的 BIOS 項目。 主選單面板 選擇快捷方式項目 子選單面板 刪除所有我的最愛 項目 回復預設值 3. 從主選單面板選擇項目,然後點選子選單中想要儲存至我的最愛的選項,再點 選或輕觸 或是按下 按鍵。 以下項目無法加入至我的最愛: • 有子選單的項目。 • 使用者自訂項目,例如:語言、開機裝置順序。 • 設定項目,例如:記憶體 SPD 資訊、系統時間與日期。 4. 點選 Exit(ESC) 或按下 鍵來關閉樹狀圖視窗。 5.
4.
• 若您忘記設定的 BIOS 密碼,可以採用清除 CMOS 即時鐘(RTC)記憶體。詳 細方法請參考主機板手冊的說明。 • Administrator 或 User Password 項目預設值為 [Not Installed],當您設定密碼 之後將顯示為 [Installed]。 Administrator Password(設定系統管理員密碼) 當您設定系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設定程式中的某些 資訊無法檢視或變更設定。 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼並選擇 OK 確認密碼正確。 請依照以下步驟變更系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2.
5.
以下項目只有在 Ai Overclock Tuner 設定為 [Manual]、[AEMP]、[EXPO I]、[EXPO II]、 或 [AEMP] 時才會出現。 BCLK Frequency 本項目可以設定 BCLK 頻率以增進系統效能。請使用 <+> 與 <-> 鍵調整數值。 建議您依照處理器規格設定數值,設定過高的數值可能造成處理器永久性的損害。 以下項目只有在 Ai Overclock Tuner 設定為 [AEMP] 時才會出現。 AEMP 本項目可以用來選擇 ASUS Enhanced Memory Profile(AEMP)。每個資料都有專屬 動態隨機存取記憶體(DRAM)頻率、時間與電壓。 以下項目只有在 Ai Overclock Tuner 設定為 [EXPO I] 或 [EXPO II] 時才會出現。 EXPO 本項目用來選擇 EXPO 設定檔。每個設定檔都有專屬動態隨機存取記憶體(DRAM) 頻率、時間與電壓。 以下項目只有在 Ai Overclock Tuner 設定為 [D.O.C.P.] 時才會出現。 D.O.C.P. 本項目可以選擇 D.O.C.P.
CPU Core Ratio (Per CCX) 本項目用來設定每個 CCX 的核心比值。 Core VID 本項目用來設定自定 CPU 核心 VID。省電功能供閒置核心(例如 cc6 sleep) 保持活動。設定值有:[Auto] [0.700] - [1.700] CCD0 CCX0 Ratio 本項目用來為 CCX 設定自定 CPU 核心。設定值有:[Auto] [12.00] - [100.
DRAM RAS# to CAS# Delay 設定值有:[Auto] [1] - [63] DRAM RAS# PRE Time 設定值有:[Auto] [1] - [63] DRAM RAS# ACT Time 設定值有:[Auto] [1] - [127] Secondary Timings DRAM Row Cycle Time 設定值有:[Auto] [1] - [255] DRAM WRITE to READ Delay 設定值有:[Auto] [2] - [126] DRAM REF Cycle Time 設定值有:[Auto] [1] - [4095] Trfc2 設定值有:[Auto] [1] - [4095] Trfcsb 設定值有:[Auto] [1] - [2047] DRAM READ to PRE Time 設定值有:[Auto] [1] - [31] DRAM RAS# to RAS# Delay L 設定值有:[Auto] [1] - [31] DRAM RAS# to RAS# Delay S 設定值有:[Auto] [1] - [31] Tfaw 設定值有:[Auto] [
TwrwrSc 設定值有:[Auto] [1] - [15] TwrwrSd 設定值有:[Auto] [1] - [15] TwrwrDd 設定值有:[Auto] [1] - [15] Twrrd 設定值有:[Auto] [1] - [15] Trdwr 設定值有:[Auto] [1] - [63] DRAM Signal Control Proc CA Drive Strength 設定值有:[Auto] [120 ohm] [60 ohm] [40 ohm] [30 ohm] Rtt Nom Wr 設定值有:[Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3 (80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)] Rtt Nom Rd 設定值有:[Auto] [RTT_OFF] [RZQ (240)] [RZQ/2 (120)] [RZQ/3 (80)] [RZQ/4 (60)] [RZQ/5 (48)] [RZQ/6 (40)] [RZQ/7 (34)] Rtt Wr 設定值有:[Auto] [R
Precision Boost Overdrive Precision Boost Overdrive 開啟本項目可讓處理器運作超出 PPT、VDD_CPU EDC、VDD_CPU TDC、VDD_ SOC EDC、VDD_SOC TDC 的定義值,以達到電路板的極限,並允許其在更 高的電壓下升壓,讓持續時間超過預設的操作。設定值有:[Auto] [Disabled] [Enabled] [Manual] 以下項目只有在 Precision Boost Overdrive 設為 [Manual] 時才會出現。 PPT Limit PPT Limit [W],插槽電力容量,可調整至主機板程式設定的 PPT Limit。設定 值有:[Auto] [0] - [65535] TDC Limit TDC Limit [A],持續電流傳輸容量,可調整至主機板程式設定的 TDC Limit。 設定值有:[Auto] [0] - [65535] EDC Limit EDC Limit [A],電流傳輸容量,可調整至主機板程式設定的 EDC Limit。設定 值有:[Auto] [0] - [65535] SOC TDC
CPU Boost Clock Override 本項目可以透過 CPU Boost 演算法自動增加或減少最大處理器頻率值。設定值 有:[Disabled] [Enabled (Positive)] [Enabled (Negative)] 以下的項目僅當 CPU Boost Clock Override 設定為 [Enabled (Positive)] 時才會出 現。 Max CPU Boost Clock Override(+) 本項目可以透過 Precision Boost 2 演算法自動增加最大處理器頻率值。設定值 有:[Auto] [0] - [200] 以下的項目僅當 CPU Boost Clock Override 設定為 [Enabled (Positive)] 時才會出 現。 Max CPU Boost Clock Override(+) 本項目可以透過 Precision Boost 2 算法自動減少最大處理器頻率值。設定值 有:[Auto] [0] - [200] Platform Thermal Throttle Limit 本項目可用來降低允許的最高處理器溫度(攝氏)。設定值有:
以下項目只有當 Curve Optimizer 設定為 [Per Core] 時才會出現。 Core 0-5 Curve Optimizer Sign 決定此核心曲線切換的方向。正向使曲線升高以使用更高電壓。負 向使曲線降低以使用較低電壓。設定值有:[Positive] [Negative] Core 0-5 Curve Optimizer Magnitude 決定曲線切換層級,輸入的數值越高表示切換的層級越大。設定值 有:[0] - [30] GFX Curve Optimizer GFX Curve Optimizer 本項目可以切換 GFX 電壓 / 頻率 (AVFS) 曲線以包含較高電壓( 正數值)或較低電壓(負數值)。輸入的數值越高表示電壓切換的 層級越大。設定值有:[Auto] [GFX Curve Optimizer] 以下項目只有當 GFX Curve Optimizer 設定為 [GFX Curve Optimizer] 時才會出現。 GFX Curve Optimizer Sign 決定 GFX 的曲線切換方向。正向使曲線升高以使用更高電壓。負向 使曲線降低以使用較低電壓。設定值有:[
CPU Current Capability 較高的值可提供更寬的總功率範圍,並同時擴大超頻頻率範圍。設定值 有:[Auto] [100%] - [140%] 當 CPU 超頻或是需負載額外的電力時,請設置較高的數值。 CPU VRM Switching Frequency 本項目用來設定 VRM 開關頻率。VRM 開關頻率影響瞬態回應與 VRM 元件溫 度。當處理器運作於高電壓與高負載線校準值時,建議使用 VRM 散熱器主動 冷卻。設定值有:[Auto] [Manual] 請勿將散熱系統移除,散熱環境需受到監控。 以下項目只有在 CPU VRM Switching Frequency 設定為 [Manual] 時才會出現。 Fixed CPU VRM Switching Frequency(KHz) 本項目可讓您設定固定的 VRM 頻率。數值以 50KHz 為間隔,變更的範圍由 300KHz 至 800KHz。 CPU Power Duty Control 本項目用來調整每個元件相數的電流與散熱環境。 [T.
以下項目只有在 CPU VRM Switching Frequency 設定為 [Manual] 時才會出現。 Power Phase Response 本項目用來為 CPU 設定較快的相式響應以增進系統效能,或是較低的相式 響應來降低 DRAM 電力效能。選擇一般模式時需要較長的反應時間。設定值 有:[Ultra Fast] [Fast] [Medium] [Regular] VDDSOC Load-Line Calibration 設定值有:[Auto] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] VDDSOC Current Capability 設定值有:[Auto] [100%] - [140%] VDDSOC Switching Frequency 設定值有:[Auto] [Manual] 以下項目只有在 VDDSOC Switching Frequency 設定為 [Manual] 時才會出現。 Fixed VDDSOC VRM Switching Frequency(KHz)
Tweaker’s Paradise Clock Spread Spectrum 本項目用來啟動或關閉展頻時脈產生器。設定值有:[Auto] [Enabled] [Disabled] 1.8V PLL Voltage 本項目用來設定 1.8V PLL 電壓。請使用 <+> 與 <-> 鍵調整數值。數值 以 0.010V 為間隔,變更的範圍由 1.500V 至 2.500V。設定值有:[Auto] [1.50000] - [2.50000] 1.8V Standby Voltage 本項目用來設定 1.8V 待機電壓。請使用 <+> 與 <-> 鍵調整數值。數值 以 0.010V 為間隔,變更的範圍由 1.500V 至 2.500V。設定值有:[Auto] [1.50000] - [2.50000] Misc_ALW 本項目用來設定 Misc_ALW 電壓。請使用 <+> 與 <-> 鍵調整數值。數值 以 0.010V 為間隔,變更的範圍由 0.600V 至 1.500V。設定值有:[Auto] [0.60000] - [1.
以下項目只有在 Algorithm 1 設定為 [Enabled] 時才會出現。 Algorithm 1-3 Condition 選擇情況以監控並生效。當多個演算法觀察相同情況,結果為「AND」並小 於 2 即會寫入動作數值。設定值有:[Auto] [CPU Temperature] [Core Voltage] [Core Current] Algorithm 1-3 Action 選擇目標情況超越臨界值時採取的動作。當多個演算法執行相同動作,結果為 「AND」並小於 2 即會寫入動作數值。設定值有:[Auto] [Package Power Limit Fast] [Package Power Limit Slow] [Thermal Limit] [Vcore TDC Limit] [Vcore EDC Limit] [SOC TDC Limit] [SOC EDC Limit] Level 1 Threshold Value 設定邊界區隔 Level1 動作數值與 Level2 動作數值。當情況小於或等於此數值 時, Level1 動作數值將會被寫入。當小於 Level2 臨界值時,Level2 動
以下項目只有在 CPU Core Voltage 設定為 [Manual Mode] 時才會出現。 CPU Core Voltage Override 本項目用來讓您透過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.625V 至 1.700V。設定值有:[Auto] [0.62500] - [1.70000] 以下項目只有在 CPU Core Voltage 設定為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設定正數值偏移電壓。 [-] 設定負數值偏移電壓。 CPU Core Voltage Offset 本項目用來讓您透過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.005V 至 0.500V。設定值有:[Auto] [0.00500] - [0.
Misc Voltage 設定值有:[Auto] [Offset Mode] 以下項目只有在 Misc Voltage 設定為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設定正數值偏移電壓。 [-] 設定負數值偏移電壓。 Misc Voltage Offset 請使用 <+> 與 <-> 鍵調整數值。數值以 0.010V 為間隔,變更的範圍由 0.010V 至 0.500V。設定值有:[Auto] [0.01000] - [0.50000] VDDP Voltage 請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.700V 至 1.800V。設定值有:[Auto] [0.70000] - [1.80000] High DRAM Voltage Mode 若本項目設定為 [Disabled],則動態隨機存取記憶體電壓的上限為 1.435V;若設定 為 [Enabled],則上限為 2.
SPD HUB VDDIO (1.0V) 本項目可以設定 SPD Hub 邊帶界面的主電源。預設值為 1.0V。請使用 <+> 與 <-> 鍵調整數值。數值以 0.100V 為間隔,變更的範圍由 0.900V 至 1.200V。 設定值有:[Auto] [0.90000] - [1.20000] Memory VDD Voltage 本項目可以設定 DRAM IC 之 VDD 部分的電源。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.800V 至 1.435V。設定值 有:[Auto] [0.80000] - [1.43500] Memory VDDQ Voltage 本項目可以設定 DRAM IC 之資料部分的電源。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.800V 至 1.435V。設定值 有:[Auto] [0.80000] - [1.43500] Memory VPP Voltage 本項目可以設定 DRAM 啟動電源供應器的電源。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.
6.
6.
Physical Presence Spec Version 本項目用來選擇告訴作業系統支援 PPI 版本 1.2 或 1.3。設定值有:[1.2] [1.3] 部分 HCK 測試可能未支援 PPI Spec 版本 1.3。 6.
6.
L2 Stream HW Prefetcher 本項目用來開啟或關閉 L2 Stream HW Prefetcher。設定值 有:[Disable] [Enable] [Auto] L1 Stride Prefetcher 設定值有:[Disable] [Enable] [Auto] L1 Region Prefetcher 設定值有:[Disable] [Enable] [Auto] L2 Up/Down Prefetcher 設定值有:[Disable] [Enable] [Auto] Core Watchdog Core Watchdog Timer Enable 本項目用來開啟或關閉 CPU 看門狗計時器。設定值有:[Disabled] [Enabled] [Auto] 以下項目只有在 Core Watchdog Timer Enable 設定為 [Enabled] 時才會出現。 Core Watchdog Timer Interval 設定 CPU 看門狗計時器的間隔。設定值有:[Auto] [39.68us] [80.64us] [162.56us] [326.4us] [654.
MCA error thresh enable 本項目用來啟動 MCA 錯誤臨界值。設定值有:[False] [True] [Auto] 以下的項目僅當 MCA error thresh enable 設定為 [True] 時才會出現。 MCA error thresh count 本項目可以設定錯誤臨界值 = 4095(0xFFF) - <此數值>(例如預設值 0xFF5 為 臨界值 10)。[1] - [4095] SMU and PSP Debug Mode 本項目設定為 [Enabled] 時,PSP 韌體或 SMU 韌體偵測到不可修正錯誤時會 假當機而非重啟系統。設定值有:[Disabled] [Enabled] [Auto] PPIN Opt-in 本項目用來啟動或關閉 PPIN 功能。設定值有:[Disabled] [Enabled] [Auto] Fast Short REP MOVSB 本項目預設值為 1,為了分析使用無法設為 0。設定值有:[Disabled] [Enabled] Enhanced REP MOVSB/STOSB 本項目預設值為 1,為了分析使用無法設為 0。設定值有:[
以下的項目僅當 SNP Memory (RMP Table) Coverage 設定為 [Custom] 時才會出 現。 Amount of Memory to Cover 以十六進位為單位指定被覆蓋的系統記憶體。設定值有:[0] - [100000] SMEE 本項目用來啟動或關閉 SMEE。設定值有:[Disable] [Enable] [Auto] Action on BIST Failure 本項目用來設定當檢測到 CCD BIST 錯誤時的動作。設定值有:[Do nothing] [Down-CCD] [Auto] DF Common Options Memory Addressing Memory interleaving 本項目用來啟用或關閉記憶體交錯。設定值有:[Disabled] [Auto] Memory interleaving size 設定記憶體交錯的大小。有效數值為 AUTO、256 位元、512 位 元、1 千位元組或 2 千位元組。此選項可決定開始交錯的位址(位 元 8、9、10 或 11)。設定值有:[256 Bytes] [512 Bytes] [1KB] [2KB]
Disable DF sync flood propagation 本項目可以啟用或關閉 DF 同步 SYN 洪水攻擊。設定值有:[Sync flood disabled] [Sync flood enabled] [Auto] Freeze DF module queues on error 設定值有:[Disabled] [Enabled] [Auto] DF Cstates 當本項目設為 [Enabled] 時,FW 安排暫存器啟用本功能。(選擇 [Auto] 時, 表示此選項會與 Global C State 同步。)設定值有:[Disabled] [Enabled] [Auto] PSP error injection support 設定值有:[False] [True] UMC Common Options DDR Options DDR Timing Configuration 本項目用來設定記憶體時序。 系統製造商的保固不包括因使用不符合規格或超出出廠設定的 AMD 處理器而造成 的損毀。 以下項目只有在 DRAM Timing Configuration 設定為 [Accept] 時才
以下項目只有在 Trcd Ctrl 設定為 [Manual] 時才會出現。 Trcd 指定 the RAS# Active to CAS# Read Delay Time。有 效數值(2 或 2 的倍數):0x8 ~ 0x3E。數值應為十 六進位。 Trp Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trp Ctrl 設定為 [Manual] 時才會出現。 Trp 指定 Row Precharge Delay Time。有效數值(2 或 2 的倍數):0x8 ~ 0x3E。數值應為十六進位。 Tras Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Tras Ctrl 設定為 [Manual] 時才會出現。 Tras 指定 Active to Precharge Delay Time。有效數值(2 或 2 的倍數):0x1E ~ 0x7E。 Trc Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trc Ctrl 設定為 [Manual] 時才會出現。 Trc 指定 Acti
Trfc2 Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trfc2 Ctrl 設定為 [Manual] 時才會出現。 Trfc2 指定 Refresh Recovery Delay Time(tRFC2)。有效數 值:0x32 ~ 0xFFF。數值應為十六進位。 TrfcSb Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trfcsb Ctrl 設定為 [Manual] 時才會出現。 TrfcSb 指定 Refresh Recovery Delay Time(tRFCSB)。有效 數值:0x32 ~ 0x7FF。數值應為十六進位。 DDR Non-SPD Timing Trtp Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trtp Ctrl 設定為 [Manual] 時才會出現。 Trtp 指定 Read CAS# to Precharge command delay time。 有效數值:0x5 ~ 0x1F。數值應為十六進位。 TrrdL Ctrl [Auto] 使用預設
以下項目只有在 Tfaw Ctrl 設定為 [Manual] 時才會出現。 Tfaw 指定 Four Activate Window Time。有效數值:0x14 ~ 0x50。數值應為十六進位。 TwtrL Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwtrL Ctrl 設定為 [Manual] 時才會出現。 TwtrL 指定 Minimum Write to Read Time,相同資料組。有 效數值:0x8 ~ 0x30。數值應為十六進位。 TwtrS Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwtrS Ctrl 設定為 [Manual] 時才會出現。 TwtrS 指定 Minimum Write to Read Time,不同資料組。有 效數值:0x2 ~ 0x10。數值應為十六進位。 TrdrdScL Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrdrdScL Ctrl 設定為 [Manual] 時才會出現。 TrdrdScL 指定 CAS 至 CA
TrdrdDd Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrdrdDd Ctrl 設定為 [Manual] 時才會出現。 TrdrdDd 指定不同記憶體間讀取至讀取的周轉時間。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TwrwrScL Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrScL Ctrl 設定為 [Manual] 時才會出現。 TwrwrScL 指定 CAS 至 CAS 延遲時間,相同資料組。有效數 值:0x1 ~ 0x3F。 TwrwrSc Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrSc Ctrl 設定為 [Manual] 時才會出現。 TwrwrSc 指定相同片選間寫入至寫入的周轉時間。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TwrwrSd Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrSd Ctrl 設定為 [Manual] 時才會出現。 TwrwrSd 指定
Trdwr Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trdwr Ctrl 設定為 [Manual] 時才會出現。 Trdwr 指定讀取至寫入的周轉時間。有效數值:0x1 ~ 0x1F。數值應為十六進位。 DDR BUS Configuration 本項目可以進行 DDR BUS 設定。 Processor CK drive strengths 指定 Processor CK drive strengths。設定值有:[Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0 Ohm] Processor CA drive strengths 指定 Processor CA drive strengths。設定值有:[Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0 Ohm] Processor CS drive strengths 指定 Processor CS drive strengths。設定值有:[Auto] [120.0 Ohm] [60.0 Ohm] [40.
DRAM DQ drive strengths 指定 DRAM DQ drive strengths。設定值有:[Auto] [48 ohm] [40 ohm] [34 ohm] DDR Controller Configuration 本項目用來設定 DDR 控制器。 DDR Power Options Power Down Enable 本項目用來開啟或關閉 DDR 斷電模式。設定值 有:[Disabled] [Enabled] [Auto] DDR RAS 本項目可以讓您設定 DDR RAS。 Disable Memory Error Injection 設定值有:[False] [True] [Auto] DDR ECC Configuration DDR Security 本項目可以讓您設定 DDR 安全性。 TSME 設定值有:[Auto] [Enabled] [Disabled] Data Scramble 設定值有:[Enabled] [Disabled] [Auto] DDR Addressing Options 本項目用來設定 DDR Addressing。 Chipselect In
以下的項目僅當 MBIST Enable 設定為 [Enabled] 時才會出現。 MBIST Test Mode 本項目可以選擇 MBIST 測試模式。設定值有:[Interface Mode] [Data Eye Mode] [Both] [Auto] MBIST Aggressors 本項目可以啟用或關閉 Memory Aggressor 測試。設定值 有:[Disabled] [Enabled] [Auto] MBIST Per Bit Slave Die Reporting 在每個 DQ、片選與通道回報 ABL Log 的 2D Data Eye 結果。 設定值有:[Disabled] [Enabled] [Auto] DDR Data Eye Pattern Select 設定值有:[PRBS] [SSO] [Both] Pattern Length 可能選項為 N=3...
GPU Host Translation Cache 本項目用來開啟或關閉 GPU Host Translation Cache。設定值 有:[Disabled] [Enabled] [Auto] Audio Configuration 本項目可以進行音效設定。 NB Azalia 本項目可以啟用或關閉 HD 控制器。設定值有:[Disabled] [Enabled] [Auto] Audio IOs 設定值有:[Auto] [HDA(3SDI) + PDM(2CH)(Default)] [HDA (1SDI) + PDM(6CH)] [HDA(1SDI) + SW0(1MDATA) + PDM(2CH)] [SW0(4MDATA) + PDM(6CH)] [SW0(4MDATA) + SW1(1MDATA) + PDM(2CH)] PCIe loopback Mode 本項目用來開啟或關閉 PcieLoopBackMode。設定值有:[Auto] [Disabled] [Enabled] SMU Common Options TDP Control [Auto] 使用預設值。 [Manual] 使用者可
EDC Control [Auto] 使用預設 EDC Limit。 [Manual] 使用者自訂 EDC Limit。 以下的項目僅當 EDC Control 設定為 [Manual] 時才會出現。 TDC_VDDCR_VDD 本項目可以設定 VDDCR_VDD EDC Limit [mA]。 PROCHOT Control [Auto] 使用預設值。 [Manual] 使用者可自訂 PROCHOT。 以下的項目僅當 PROCHOT Control 設定為 [Manual] 時才會出現。 ROCHOT Deassertion Ramp Time 本項目可以設定 ROCHOT Deassertion Ramp Time [ms]。 Fan Control [Auto] 使用預設風扇設定。 [Manual] 使用者自訂風扇設定。 以下項目只有在 Fan Control 設為 [Manual] 時才會出現。 Fan Table Control [Auto] 使用預設值。 [Manual] 使用者自訂。 以下項目只有在 Fan Table Control 設為[Manual] 時才會出現。
PWM Frequency [Auto] 設為預設值。 [1] 100Hz [0] 25kHz Fan Polarity [Auto] 設為預設值。 [1] 正值。 [0] 負值。 VDDP Voltage Control [Auto] 使用預設 VDDP 電壓。 [Manual] 使用者自訂 VDDP 電壓。 以下項目只有在 VDDP Voltage Control 設為 [Manual] 時才會出現。 VDDP Voltage 本項目用來設定目標 VDDP 電壓 [mV]。設定值有:[0] - [2000] Infinity Fabric Frequency and Dividers 設定值有:[Auto] [100MHz] - [1066MHz] FEATURE FCLK DPM 設定值有:[Auto] [Disabled] [Enabled] SyncFifo Mode Override 設定值有:[Disable] [Enable] [Auto] 48 PRIME / ProArt / TUF GAMING AMD 600 系列 BIOS 使用手冊
6.
6.
6.
USB Single Port Control 本項目用來啟動或關閉個別 USB 連接埠。 USB 連接埠的位置請參考主機板手冊裡 主機板構造圖 與 後側面板連接埠 的說 明。 6.7 網路協定堆疊設定(Network Stack Configuration) 本選單可讓您變更網路協定堆疊的各項相關設定。 Network stack 本項目用來啟動或關閉 UEFI 網路協定堆疊(Network Stack)功能。設定值 有:[Disabled] [Enabled] 以下的項目僅當 Network Stack 設定為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support 本項目用來啟動或關閉 Ipv4/Ipv6 PXE 開機選項。設定值有:[Disabled] [Enabled] 6.
6.
6.
SMART Self Test S.M.A.R.T.(自動偵測、分析、報告技術,Self-Monitoring, Analysis and Reporting Technology)是一個監控軟體,可以監控您的硬碟,並在發生錯誤時於開機自我檢測 (POST)時顯示錯誤訊息。設定值有:[Disabled] [Enabled] SATA6G_1 - SATA6G_4 本項目可啟用或關閉選擇的 SATA 連接埠。設定值有:[Disabled] [Enabled] SATA6G_1 - SATA6G_4 Hot Plug 指定此連接埠支援熱抽換功能。設定值有:[Disabled] [Enabled] 6.
Power On By PCI-E 本項目用來啟動或關閉內建網路控制器或其他安裝的 PCI-E 網路卡的喚醒功能。設 定值有:[Disabled] [Enabled] Power On By RTC 本項目用來關閉或開啟即時時鐘(RTC)喚醒功能,啟用時您可自行設定天、小時、 分、秒以安排時間讓系統自動開機。設定值有:[Disabled] [Enabled] 6.
PCIEX16_2 Bandwidth Bifurcation Configuration [PCIE X8 Mode] 切換 PCIEX16_2 為 x8。 [PCIE RAID Mode] 安裝在 Hyper M.2 X16 系列卡上可被偵測的 SSD 最多為 2 個。 當安裝 Hyper M.2 X16 系列卡或其他 M.
10G LAN Card 本項目用來啟動或關閉 10G 網卡。設定值有:[Disabled] [Enabled] USB power delivery in Soft Off state (S5) 本項目用來當您的電腦處於 S5 狀態時開啟或關閉 USB 電源。設定值有:[Disabled] [Enabled] Serial Port Configuration 以下的項目可以讓您進行序列埠設定。 本項目只有在主機板上有序列埠(COM)連接器時,才有作用。 Serial Port 本項目可以啟動或關閉序列埠。設定值有:[Enabled] [Disabled] 以下的項目只有在 Serial Port 項目設為 [Enabled] 時才會出現。 Change settings 本項目用來為 Super I/O 裝置選擇最佳設定。 設定值有:[IO=3F8h; IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3] PCIE Link Speed 以下的項目可以設定 PCIE 運作速度。 PCIEX16_1 Link Mode 本項目用來設定
Chipset_2 Link Mode 本項目用來設定 Chipset_1 與 Chipset_2 間的運作速度。設定值有:[Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] M.2_3 Link Mode 本項目用來設定 M.2_3 裝置運作速度。設定值有:[Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] PCIEX16 Link Mode 本項目用來設定 PCIEX16 插槽運作速度。設定值有:[Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4] 6.
6.
Discrete GPU HPD Circuitry 本項目用來開啟或關閉 Discrete GPU Display HPD Circuitry。設定值有:[OR Circuitry] [Pulse Circuitry] Discrete GPU’s Audio 本項目可以關閉 Discrete GPU 的音效或保持 ROM Strap Setting。設定值 有:[Disabled] [Keep ROM Strap Setting] Discrete GPU’s USB Port 本項目可以關閉獨立 GPU 的 USB 埠或維持預設值。設定值有:[Keep Default Setting] [Disabled] Discrete GPU’s SSID/SVID 根據 HybridGraphics 設定設計 Discrete GPU 的 SSID/SVID。設定值有:[Keep Default Setting] [Program by Vendor] Discrete GPU BOMACO Support 本項目提供您啟用或關閉 GPU BOMACO 支援。設定值有:[Disabled] [Enabled]
6.
SMT Control 本項目可以關閉 SMT(同時多執行緒)。想要重啟 SMT 時,需在 設定本項目為 [Auto] 為進行電源重啟。設定值有:[Auto] [Disable] 當 SMT 關閉時不支援 S3。 DDR and Infinity Fabric Frequency/Timings DDR Options DDR Timing Configuration Active Memory Timing Settings 設定值有:[Auto] [Enabled] 以下的項目只有在 Active Memory Timing Settings 設定為 [Enabled] 時才會出現。 Memory Target Speed 以 Mt/s 為單位指定記憶體目標速度。有效數值為 2000 MT/s、2400 Mt/s 與範圍介於 3200 MT/s ~ 12000 MT/s。輸入 的數值會無條件捨棄尾數以對齊步進 200 MT/s。 DDR SPD Timing Tcl Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 僅當 Tcl Ctrl 項目設為 [Manual] 時,以下項目才會
Tras Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Tras Ctrl 設定為 [Manual] 時才會出現。 Tras 指定 Active to Precharge Delay Time。有效數值(2 或 2 的倍數):0x1E ~ 0x7E。 Trc Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trc Ctrl 設定為 [Manual] 時才會出現。 Trc 指定 Active to Active/Refresh Delay Time。有效數 值:0x20 ~ 0xFF。數值應為十六進位。 Twr Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Twr Ctrl 設定為 [Manual] 時才會出現。 Twr 指定 Minimum Write Recovery Time。有效數值:0x30 ~ 0x60。數值應為十六進位。 Trfc1 Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trfc1 Ctrl 設定為 [Manual] 時才會
TrfcSb 指定 Refresh Recovery Delay Time(tRFCSB)。有效 數值:0x32 ~ 0x7FF。數值應為十六進位。 Trtp Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 Trtp Ctrl 設定為 [Manual] 時才會出現。 Trtp 指定 Read CAS# to Precharge command delay time。 有效數值:0x5 ~ 0x1F。數值應為十六進位。 TrrdL Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrrdL Ctrl 設定為 [Manual] 時才會出現。 TrrdL 指定 Activate to Activate Delay Time,相同資料組 (tRRD_L)。有效數值:0x4 ~ 0x20。數值應為十六 進位。 TrrdS Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrrdS Ctrl 設定為 [Manual] 時才會出現。 TrrdS 指定 Activate to Activate D
TwtrS Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwtrS Ctrl 設定為 [Manual] 時才會出現。 TwtrS 指定 Minimum Write to Read Time,不同資料組。有 效數值:0x8 ~ 0x30。數值應為十六進位。 DDR Non-SPD Timing TrdrdScL Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrdrdScL Ctrl 設定為 [Manual] 時才會出現。 TrdrdScL 指定 CAS 至 CAS 延遲時間,相同資料組。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TrdrdSc Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrdrdSc Ctrl 設定為 [Manual] 時才會出現。 TrdrdSc 指定相同片選間讀取至讀取的周轉時間。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TrdrdSd Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TrdrdSd
以下項目只有在 TwrwrScL Ctrl 設定為 [Manual] 時才會出現。 TwrwrScL 指定 CAS 至 CAS 延遲時間,相同資料組。有效數 值:0x1 ~ 0x3F。數值應為十六進位。 TwrwrSc Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrSc Ctrl 設定為 [Manual] 時才會出現。 TwrwrSc 指定相同片選間寫入至寫入的周轉時間。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TwrwrSd Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrSd Ctrl 設定為 [Manual] 時才會出現。 TwrwrSd 指定相同記憶體間寫入至寫入的周轉時間。有效數 值:0x1 ~ 0xF。數值應為十六進位。 TwrwrDd Ctrl [Auto] 使用預設值。 [Manual] 手動設定。 以下項目只有在 TwrwrDd Ctrl 設定為 [Manual] 時才會出現。 TwrwrDd 指定不同記憶體間寫入至寫入的周轉時間。有效數 值:0x1 ~ 0xF。數
DDR BUS Configuration Processor CA drive strengths 指定 Processor CA drive strengths。設定值有:[Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0 Ohm] Processor DQ drive strengths 指定 Processor DQ drive strengths。設定值有:[Auto] [High Impedance] [240 ohm] [120 ohm] [80 ohm] [60 ohm] [48 ohm] [40 ohm] [34.3 ohm] Processor ODT impedance 指定 Processor ODT impedance。設定值有:[Auto] [High Impedance] [480 ohm] [240 ohm] [160 ohm] [120 ohm] [96 ohm] [80 ohm] [68.
Precision Boost Overdrive Precision Boost Overdrive 開啟本項目可讓處理器運作超出 PPT、VDD_CPU EDC、VDD_CPU TDC、VDD_ SOC EDC、VDD_SOC TDC 的定義值,以達到電路板的極限,並允許其在更 高的電壓下升壓,讓持續時間超過預設的操作。設定值有:[Auto] [Disabled] [Enabled] [Manual] 以下項目只有在 Precision Boost Overdrive 設為 [Manual] 時才會出現。 PBO Limits [Auto] 載入 AMD 預設 PPT、EDC 與 TDC。 [Disable] 關閉 PBO 限制。 [Motherboard] 允許處理器依主機板定義的 PPT、EDC 與 TDC 限制執行。 [Manual] 允許處理器忽略 AMD 對 PPT、EDC 與 TDC 預設限制並使用手 動數值(至主機板的最大上限)。 以下項目只有在 PBO Limits 設為 [Manual] 時才會出現。 PPT Limit [mW] 調整 PPT。限制依主機板的支援而異。 T
以下的項目僅當 CPU Boost Clock Override 設定為 [Enabled (Positive)] 時才會出 現。 Max CPU Boost Clock Override(+) 本項目可以透過 Precision Boost 2 算法自動增加最大處理器頻率值。請使用 <+> 與 <-> 鍵調整數值。數值以 25 為間隔,變更的範圍由 25 至 200。設定值 有:[Auto] [0] - [200] 以下的項目僅當 CPU Boost Clock Override 設定為 [Enabled (Negative)] 時才會出 現。 Max CPU Boost Clock Override(-) 本項目可以透過 Precision Boost 2 演算法自動減少最大處理器頻率值。請使用 <+> 與 <-> 鍵調整數值。數值以 25 為間隔,變更的範圍由 25 至 200。設定值 有:[Auto] [0] - [200] Platform Thermal Throttle Ctrl 本項目可用來降低允許的最高處理器溫度(攝氏)。設定值有:[Manual] [Auto] 以下項目只有在 Plat
Curve Optimizer Curve Optimizer 本項目可以切換電壓 / 頻率 (AVFS) 曲線以包含較高電壓(正數 值)或較低電壓(負數值)。輸入的數值越高表示電壓限制的層級 越大。設定值有:[Disable] [All Cores] [Per Core] 以下項目只有當 Curve Optimizer 設定為 [All Cores] 時才會出現。 All Core Curve Optimizer Sign 決定所有核心曲線切換的方向。正向使曲線升高以使用更高電壓。 負向使曲線降低以使用較低電壓。設定值有:[Positive] [Negative] All Core Curve Optimizer Magnitude 決定曲線切換層級,輸入的數值越高表示切換的層級越大。設定值 有:[0] - [30] 以下項目只有當 Curve Optimizer 設定為 [Per Core] 時才會出現。 Core 0-5 Curve Optimizer Sign 決定此核心曲線切換的方向。正向使曲線升高以使用更高電壓。負 向使曲線降低以使用較低電壓。設定值有:[Positive] [Negative
VDDP Voltage Control VDDP Voltage Control 本項目可以用來設定 VDDP 電壓。 [Auto] 使用系統預設值。 [Manual] 自訂電壓值。 以下項目只有在 VDDP Voltage Control 設為 [Manual] 時才會出現。 VDDP Voltage Adjust VDDP 是 DDR 匯流排信號(PHY)的電壓,由 DRAM 電壓(VDDIO_Mem)衍 生。因此,毫伏特 VDDP 電壓能接近但不會超過 DRAM 電壓。設定值有:[0] - [2000] SoC/Uncore OC Mode SoC/Uncore OC Mode 強制 CPU SoC/Uncore 元件(如 Infinity Fabric、記憶體與整合顯示卡)總 是執行最大指定頻率。可能在閒置電源省電時增進效能。設定值有:[Auto] [Enabled] [Disabled] SoC Voltage SoC Voltage 以毫伏特為單位指定 SoC/Uncore 電壓(VDD_SOC)以支援記憶體與 Infinity Fabric 超頻。VDD_SOC 同時可決定處理器上整合顯
LCLK Frequency Control LCLK Frequency Control [Auto] 使用預設值。 [Manual] 手動設定 LCLK 頻率。 以下項目只有在 LCLK Frequency Control 設為 [Manual] 時才會出現。 Maximum Frequency 本項目用來設定 LCLK 頻率最大值。設定值有:[1029] - [2500] Onboard Voltage Control VDDIO Voltage Control VDDIO Ctrl 本項目可以用來設定 VDDIO 電壓。 [Auto] 使用預設 VDDIO 電壓。 [Manual] 設定 DIMM VDD/VDDQ 同步至 APU VDDIO。 [Separate] 個別設定 APU VDDIO 與 DIMM VDD/VDDQ。 執行 VDDQ != VDD 非標準程序可能會造成記憶體不穩定。請留意在增速與減速過 程 VDDQ-VDD 電壓需小於 200mV。 以下項目只有在 LCLK Frequency Control 設為 [Manual] 或 [Separate] 時才會出 現
以下項目只有在 VPP Ctrl 設為 [Manual] 時才會出現。 VPP Adjust 調整 MEM VPP,步進為 10mV。範圍為 1500mV - 2135mV。設定值 有:[1500] - [2135] 74 PRIME / ProArt / TUF GAMING AMD 600 系列 BIOS 使用手冊
7.
Voltage Monitor CPU Core Voltage, 12V Voltage, 5V Voltage, 3.3V Voltage, CPU VDDIO / MC Voltage [x.
CPU Fan Speed Low Limit 本項目用來設定風扇/水泵的最低速度警告值。當達到這個最低速度時,會出 現警告訊息。若設定為 [Ignore],將不會再出現警告訊息。設定值有:[Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] 以下項目只有在 CPU Fan Profile 設為 [Manual] 時才會出現。 CPU Fan Point4 Temperature 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調整 Point4 的溫度。 CPU Fan Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調整 Point4 的溫度。 CPU Fan Point3 Temperature 當溫度源小於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P3 溫度,佔空比會依據
CPU Fan Point1 Temperature 當溫度源小於 P1 溫度,風扇會運作於 P1 佔空比。當溫度源大於 P1 溫度, 佔空比會依據 P1-P2 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point1 的溫度。 CPU Fan Point1 Duty Cycle (%) 當溫度源小於 P1 溫度,風扇會運作於 P1 佔空比。當溫度源大於 P1 溫度, 佔空比會依據 P1-P2 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point1 的溫度。 Chassis Fan(s) Configuration Chassis Fan 1-5 Q-Fan Control 本項目用來設定 Chassis Fan 1-5 運作模式。 [Auto Detect] 偵測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/水 泵。 Chassis Fan 1-5 Profile 本項目用來設定風扇/水泵適當
以下項目只有在 Chassis Fan 1-5 Profile 設為 [Manual] 時才會出現。 Chassis Fan 1-5 Point4 Temperature 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調 整 Point4 的溫度。 Chassis Fan 1-5 Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調 整 Point4 的溫度。 Chassis Fan 1-5 Point3 Temperature 當溫度源小於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point3 的溫度。 Chassis Fan 1-5 Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫
AIO Pump Q-Fan Control 本項目用來設定 AIO Pump 運作模式。 [Auto Detect] 偵測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/水泵。 AIO Pump Profile 本項目用來設定風扇/水泵適當的效能。選擇 [Manual] 時,當處理器溫度超過 75°C 時,建議將風扇/水泵的占空比設為 100%。請留意當風扇/水泵占空比 不足導致過熱,會造成處理器效能限制。設定值有:[Standard] [Silent] [Turbo] [Full Speed] [Manual] 以下項目只有在 AIO Fan Profile 設為 [Standard]、[Silent]、[Turbo] 或 [Manual] 時才會出現。 AIO Pump Q-Fan Source 指派的風扇/水泵會依選擇的溫度來源運作。設定值有:[CPU] [MotherBoard] [VRM] [
AIO Pump Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 佔空比。使用 <+> 或 <-> 鍵調整 Point4 的溫度。 AIO Pump Point3 Temperature 當溫度源小於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point3 的溫度。 AIO Pump Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P3 溫度,佔空比會依據 P3-P4 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point3 的溫度。 AIO Pump Point2 Temperature 當溫度源小於 P2 溫度,佔空比會依據 P2-P3 與溫度源決定。當溫度源大於 P2 溫度,佔空比會依據 P2-P3 與溫度源決定。使用 <+> 或 <-> 鍵調整 Point2 的溫度。 AIO Pump Point2 Duty
8.
Boot from Storage Devices 本項用來選擇想要執行的儲存裝置類型。 設定值有:[Ignore] [Legacy only] [UEFI only] Boot from PCI-E/PCI Expansion Devices 本項目用來選擇想要執行的 PCIe/PCI 擴充裝置類型。設定值 有:[Ignore] [Legacy only] [UEFI only] Secure Boot 本項目用來設定 Windows® 安全啟動的相關參數以及管理系統金鑰,以提升系統在開 機自我檢測(POST)時的安全性,避免受到未授權的使用者與惡意軟體的危害 OS Type [Windows UEFI Mode] 本項目用來選擇安裝的作業系統。執行 Microsoft® 安全開機檢查。只有在 Windows® UEFI 模式或其他 Microsoft® 安全開機相容作業系統中開機時選擇此項 目。 [Other OS] 在 Windows® 非 UEFI 模式中開機時獲得最佳功 能。Microsoft® 安全開機功能只可在 Windows® UEFI 模式下正確執行。 Microsoft® 安全啟動功
Set New key 本項目用來由 USB 儲存裝置載入已下載平台金鑰(PK)。 Delete key 本項目用來移除系統中的 PK。當平台金鑰刪除後即無法使用安全啟 動金鑰。 設定值有:[Yes] [No] PK 檔必須格式化為一個基於時間認證變量的 UEFI 變量構造。 KEK Management KEK(金鑰交換金鑰 [Key-exchange Key] 或金鑰註冊金鑰 [Key-Enrollment Key] )用來管理簽名資料庫(db)與撤銷簽名資料庫(dbx)。 Key-exchange Key(KEK)指的是 Microsoft® Secure Boot Key-Enrollment Key(KEK)。 Save to file 本項目用來將平台金鑰(KEK)儲存至 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入已下載平台金鑰(KEK)。 Append Key 本項目用來由儲存裝置載入附加的 KEK,以管理附加的簽名資料庫 (db)與撤銷簽名資料庫(dbx)。 Delete key 本項目用來移除系統中的 KEK。 設定值有:[Yes] [No] KEK
DBX Management dbx(撤銷簽名資料庫)列出 db 項目中不再被信任且無法被載入之被禁止的圖 片影像。 Save to file 本項目用來儲存 dbx 至 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入已下載的 dbx。 Append Key 本項目用來由儲存裝置載入附加的 dbx,以管理附加的簽名資料庫 (db)與撤銷簽名資料庫(dbx)。 Delete key 本項目用來移除系統中的 dbx 檔。設定值有:[Yes] [No] dbx 檔必須格式化為一個基於時間認證變量的 UEFI 變量構造。 Boot Configuration Fast Boot 本項目可以啟用或關閉開機時僅執行最少所需裝置。不會對 BBS 開機選項造 成影響。設定值有:[Disabled] [Enabled] 僅當 Fast Boot 項目設為 [Enabled] 時,以下項目才會出現。 Next Boot after AC Power Loss [Normal Boot] [Normal Boot] 電源中斷後,在下一次啟動時恢復至正常啟動速度。 電源中斷後,在下一次啟動時加快
以下項目只有在 Boot Logo Display 設定為 [Disabled] 時才會出現。 Post Report 本項目可以讓您選擇 POST 的等候時間或直到按下 ESC。設定值有:[1 sec] [10 sec] [Until Press ESC] Boot up NumLock State 本項目可以選擇鍵盤 NumLock 狀態。設定值有:[On] [Off] Wait For ‘F1’ If Error 系統開機過程出現錯誤訊息時,本項目可讓系統等待您按下 鍵確認才會 繼續進行開機程序。設定值有:[Disabled] [Enabled] Option ROM Messages [Force BIOS] [Keep Current] 選購裝置韌體資訊會在開機自我檢測時顯示。 在開機自我檢測時只顯示華碩開機圖示。 Interrupt 19 Capture 本項目用來開啟或關閉選購裝置韌體資訊以進行 Interrupt 19 Capture。設定值 有:[Enabled] [Disabled] AMI Native NVMe Driver Support 本項目用來開啟或關閉 AMI
9.
9.1 華碩 EZ Flash 3 公用程式(ASUS EZ Flash 3 Utility) 本項目可以讓您執行華碩 EZ Flash 3 公用程式。按下 會出現再次確認的視 窗,請使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 華碩 EZ Flash 3 的說明。 9.
9.
9.4 華碩 SPD 資訊(ASUS SPD Information) 本選單顯示記憶體插槽的相關資訊。 9.
9.
10. 離開 BIOS 程式(Exit menu) 本選單可讀取 BIOS 程式出廠預設值與離開 BIOS 程式,並可儲存與取消對 BIOS 項 目的變更。您也可以由 Exit 選單進入 EZ Mode。 Load Optimized Defaults 本項目可以載入 BIOS 程式設定選單中每個參數的預設值。請選擇本項目或按下 ,便會出現一個確認對話視窗,選擇 OK 以載入預設值。 Save Changes & Reset 當您完成對 BIOS 設定程式所做的變更後,請選擇本項目或按下 ,便會出現一 個確認對話視窗,請選擇 OK 以儲存設定並離開 BIOS 設定程式。 Discard Changes & Exit 本項目可以放棄所做的變更,並回復原先儲存的設定。在選擇本項目或按下 鍵 後,將會出現一個確認對話視窗,請選擇 Yes 以放棄任何設定並載入原先儲存的設 定,同時離開 BIOS 設定程式。 Launch EFI Shell from USB drives 本項目可以讓您由含有資料系統的裝置中啟動 EFI Shell(shellx64.
11. 更新 BIOS 程式 華碩網站上提供最新的 BIOS 程式,可以強化系統的穩定度、相容性或執行效能,但 是執行 BIOS 程式更新具有潛在性風險,若是使用現有版本的 BIOS 程式未發生問題 時,請勿手動執行更新 BIOS 程式。不適當的 BIOS 程式更新可能會導致系統開機失 敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程式。 請造訪華碩網站(http://www.asus.com/support)來下載本主機板最新的 BIOS 檔 案。 以下工具程式項目提供您管理與更新主機板 BIOS 設定程式。 1. 華碩 EZ Flash 3:使用 USB 隨身碟更新 BIOS。 2. 華碩 CrashFree BIOS 3: 當 BIOS 檔案遺失或損毀時,可以使用 USB 隨身碟來 更新 BIOS。 11.1 華碩 EZ Flash 3(ASUS EZ Flash 3) 華碩 EZ Flash 3 程式讓您使用 USB 隨身碟輕鬆的更新 BIOS 程式。 請依照以下步驟透過華碩 EZ Flash 3 更新 BIOS 程式: 1.
11.2 華碩 CrashFree BIOS 3(ASUS CrashFree BIOS 3) 華碩最新自行研發的 CrashFree BIOS 3 工具程式,讓您在當 BIOS 程式和資料被病毒 入侵或毀損時,可以輕鬆的從含有最新或原始 BIOS 檔案的 USB 隨身碟中回復 BIOS 程式的資料。 請至 http://www.asus.com/support 網站下載最新 BIOS 檔案,並儲存在 USB 隨身 碟中。 回復 BIOS 程式 請依照下列步驟回復 BIOS 程式: 1. 啟動系統。 2. 將含有最新或原始 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 3. 接著工具程式便會自動檢查儲存裝置中是否存有 BIOS 檔案。當搜尋到 BIOS 檔案後,工具程式會開始讀取 BIOS 檔案並自動進入 ASUS EZ Flash 3 程式。 4.