VG2771A 系列 液晶顯示器 使用手冊
目錄 注意事項 ....................................................................................................... iii 安全資訊 ....................................................................................................... iv 維護與清潔 .................................................................................................... vi 1.1 歡迎使用! ..................................................................................... 1-1 1.2 包裝內容 ..............................................................
注意事項 聯邦通訊委員會 (FCC) 聲明 本裝置符合 FCC 條款第 15 部份的規定。操作程序受限於下列兩項條件: • 本裝置不得引起有害干擾。 • 本裝置須能承受任何可接收的干擾,包括可能導致意外操作的干擾。 本設備經測試符合 FCC 條款第 15 部份關於 B 類數位裝置的規定。這些限 制之主要目的乃針對在住宅區內安裝裝置時,提供有害干擾的合理保護。本 設備會產生、使用並放射無線射頻能量,如未根據製造商的指示方法安裝和 使用本設備,可能會對無線電通訊造成有害干擾。然而,我們無法保證在特 定環境下安裝此設備不會造成任何干擾。若本設備確實對無線電或電視接收 造成不良干擾(請開關設備加以確認),您可採取以下方式改善干擾情形: • 重新調整收訊天線的方向或位置。 • 將設備與接收器之間的距離加大。 • 將設備與接收器插至使用不同電路的電源插座。 • 向有經驗的無線電 電視技術人員尋求協助。 加拿大通訊部聲明 根據加拿大通訊部於無線電干擾法規中針對數位裝置產生無線電干擾所制定 的 B 類限制,本數位裝置所產生之無線電干擾並未超出上限。 本 B 類數位裝置符合加拿大 ICES-003 之規定
安全資訊 iv • 安裝本顯示器之前,請詳閱產品包裝內的說明文件。 • 為避免起火或觸電,請勿將顯示器暴露於下雨或潮濕的環境中。 • 切勿嘗試打開顯示器機殼。顯示器內的高壓電可能會造成嚴重的人身傷 害。 • 若電源中斷,切勿嘗試自行修復。請洽詢合格維修技術人員或經銷商。 • 使用本產品前,請務必正確連接所有纜線,並確認電源線並未損壞。若 發現任何損壞情形,請立即洽詢經銷商。 • 機殼背面或頂端的狹槽和開口為通風孔;請勿堵塞這些狹槽。除非通風 良好,否則切勿將本產品放至於散熱器或熱源附近或上方。 • 本顯示器只能使用標籤上註明的電源類型運作。若您不確定府上的電源 類型,請洽詢經銷商或當地的電力公司。 • 請使用符合當地電源標準的電源插頭。 • 請勿讓排插和延長線過載。電源過載可能會引發火災或造成觸電。 • 請避開多塵、潮濕和溫度過高 過低的環境。請勿將顯示器放置於任何 可能潮濕之處。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本裝置的插頭,避免顯示器因電源 突波而造成損壞。 • 切勿將任何異物塞入顯示器機殼開口內,也不可讓液體潑灑流入。
警告 • 使用非指定耳機可能會因音壓過大導致聽力受損。 • 請確認建築安裝中的配電系統應具備額定值 120/240V,20A(最大)的 斷路器。 • 若電源線提供 3 插腳附接插頭,請將電源線插入接地式 3 插腳插座。請 勿停用電源線的接地插腳,例如,連接 2 插腳變壓器。接地插腳為重要 安全功能。 警語 : 使用過度恐傷害視力 注意事項 : (1) 使用 30 分鐘請休息 10 分鐘。 (2) 未滿 2 歲幼兒不看螢幕,2 歲以上每天看螢幕不要超過 1 小時。 符合性聲明 本裝置遵守相關電磁相容性 (2014/30/EU)、低電壓指令 (2014/35/EU)、 ErP 指令 (2009/125/EC) 與 RoHS 指令 (2011/65/EU) 等近似歐盟成員國法 律議會指令規定之要求。本產品經過測試並遵守資訊技術設備的諧波標準, 這些諧波標準均依歐盟官方期刊指令發佈。 WEEE 符號聲明 產品與其包裝上的此符號代表本產品不得混入您的其他家庭垃圾丟棄。相反 的,您有責任將廢棄設備交由指定回收點進行廢棄電機電子設備回收處理。 在丟棄時做好廢棄設備的分類回收將有助保護自然資源並確保以保護人類健
維護與清潔 • 抬起顯示器或變更顯示器位置前,請先拔下纜線和電源線。放置顯示器 時,請依照正確的方式抬起顯示器。抬起或移動顯示器時,請抓住顯示 器的邊緣;切勿只抓住底座或電源線。 • 清潔:請關閉顯示器電源並拔下電源線。使用不會造成刮傷的軟布清潔 顯示器表面,並以軟布沾少許中性清潔劑清除頑垢。 • 避免使用含酒精或丙酮的清潔劑。請使用液晶顯示器專用的清潔劑。切 勿將清潔劑直接噴灑在螢幕上,以免滲入顯示器內並引起觸電。 以下徵狀為顯示器正常現象: • 第一次使用本顯示器時,螢幕可能會因螢光燈的自然特性而出現閃爍的 情形。請關閉電源並重新開啟,即可讓閃爍情況消失。 • 不同的桌面圖案可能會造成螢幕出現輕微亮度不均的情況。 • 顯示同樣的影像數小時後,當您切換影像時,可能會出現原有影像的殘 影。螢幕畫面會慢慢恢復正常,關閉電源開關數小時也可以改善此情 況。 • 螢幕變黑、閃爍或無法運作時,請交由經銷商或維修中心處理。切勿自 行維修螢幕! 本手冊慣用表達方式 警告:可防止使用者因自行嘗試完成工作而受傷的資訊。 注意:可防止使用者因自行嘗試完成工作而損壞元件的資訊。 重要:使用者完成工作時必
更多詳細資訊 如需其他資訊以及產品 軟體更新,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供關於 ASUS 硬體和軟體產品的最新資訊。請參閱 http://www.asus.com 2.
1.1 歡迎使用! 感謝您購買 ASUS® 液晶顯示器! ASUS 最新的寬螢幕液晶顯示器提供更清晰、更寬廣、更鮮明的畫面顯示, 以及許多增強觀賞體驗的功能。 透過這些功能,您可以盡情享受本顯示器所帶來的便利性及愉快的視覺體 驗! 1.
1.3 組裝顯示器 組裝顯示器的方法如下 1. 對準顯示器支架上的螺絲孔和底座上的隨附螺絲。然後將底座插入顯 示器支架中。 2.
1.4 連接纜線 1.4.1 液晶顯示器背面 5 1. 耳機輸出埠 2. DP 輸入埠 3. HDMI2 連接埠 4. HDMI1 連接埠 5.
1.5 顯示器簡介 1.5.1 使用控制鈕 使用顯示器背面的控制鈕來調整影像設定。 6 6 5 5 4 4 3 3 2 2 1 1. 電源指示燈: • 2. 開 琥珀色 待機模式 關 關 按下此按鈕可開啟 關閉顯示器電源。 按下此捷徑鍵切換七種採用 GameVisual™ 智慧型影像技術的預設影像顯 示模式(風景模式、比賽模式、電影模式、RTS/RPG模式、 FPS模式、sRGB模式及 MOBA模式)。 GamePlus 按鈕: 此為捷徑鍵 1。預設設定為 GamePlus。 • 1-4 說明 白色 GameVisual 按鈕: 此為捷徑鍵 2。預設設定為 GameVisual。 • 4. 狀態 電源按鈕: • 3.
若要啟動 GamePlus: • 選擇 GamePlus 按鈕,以進入 GamePlus 主選單。 • 啟動十字瞄準線、定時器或 FPS 計數器或顯示對齊功能。 • ( ) 按鈕以選擇並按下 向上 向下移動 按壓 即可關閉,然後離開。 • 按下 ) 確認所需功能。 5 向鍵可移動十字瞄準線/定時器/FPS 計數器。 GamePlus 主選單 5. ( GamePlus 十字瞄準線 GamePlus 定時器 關閉按鈕: • 退出快速鍵 OSD 選單。 • • (5 向)按鈕: 開啟 OSD 選單。執行選取的 OSD 選單項目。 增加 減少數值或將選項向上 下 左 右移動 6.
2.
2.2 拆卸支架 底座(適用於 VESA 壁掛式安裝) 本顯示器的可拆式底座是特別針對 VESA 壁掛式安裝所設計。 拆卸支架 2-2 底座 1. 拔下電源線和訊號線。小心讓顯示器正面朝下並放入 EPS 包裝。 2. 拆下固定支架至顯示器背面的四 (4) 支螺絲。 3.
2.
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 遊戲 ASUS TUF Gaming VG277Q1A 比賽模式 HDMI-1 1920x1080@60Hz 可變外徑 AMD FreeSync Premium ELMB GamePlus GameVisual Shadow Boost 1. 按下 5 向按鈕中央以開啟 OSD 選單。 2. 按壓 及 按鈕,以切換選單中的選項。在圖示間移動時,選項名 稱會反白顯示。 3. 若要選取選單上反白的項目,請按 Center 鍵。 4. 按壓 及 按鈕,以選取所需的參數。 5. 按 Center 鍵以進入滑動桿,然後使用 或 按鈕,根據選單上的指 標進行變更。 6.
3.1.2 1.
2.
3.
4. 輸入選擇 在 HDMI-1、HDMI-2 或 DisplayPort 輸入信號中選擇輸入來源。 輸入選擇 ASUS TUF Gaming VG277Q1A 比賽模式 HDMI-1 1920x1080@60Hz HDMI-1 HDMI-2 DisplayPort 5.
6.
3.2 規格 機型 面板尺寸 最大解析度 亮度(一般) 固有對比度(一般) 視角 (CR=10) 顯示色彩 色彩飽和度 VG277Q1A 27”W (68.6cm) 1920x1080@165Hz 350cd/m2 3000:1 178°(垂直) 178°(水平) 16.7M 色彩(8 位元) 85% NTSC 反應時間 4ms (灰至灰),1ms MPRT 附屬喇叭 2W x 2 立體聲 耳機輸出 是 HDMI 音效 是 HDMI 輸入 是 DisplayPort 輸入 是 < 25W 額定電壓 AC 100~240V(內建) 開機耗電量(最大) (在無音訊/ USB/ 讀卡機連線時測量 200 nits 畫面 亮度) 機殼顏色 黑色 省電模式 < 0.5W 電源關閉模式 傾斜角度 < 0.3W -5° ~ +23° 實體尺寸(寬x高x深) 615 x 453 x 194 mm 實體尺寸不含底座(寬x高x深) 615 x 453 x 59 mm 外盒尺寸(寬x高x深) 680 x 510 x 171 mm 淨重(估計值) 4.
3.
3.4 支援時序清單 HDMI / DP 輸入的 PC 時序清單 解析度 HDMI1(1.4) HDMI2(1.
設備名稱:液晶顯示器 限用物質及其化學符號 單元 鉛 汞 鎘 六價鉻 多溴聯苯 多溴二苯醚 (Pb) (Hg) (Cd) (PBB) (Cr+6 ) (PBDE) ○ ○ ○ ○ ○ ○ 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 液晶面板 ○ ○ ○ ○ ○ - ○ ○ ○ ○ ○ 電路板組件 - ○ ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ 電源線 - ○ ○ ○ ○ ○ 其他線材 - 備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含 量基準值。 備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考3.