TUF Gaming 显示器 VG1A 系列 用户指南
第一版 V1 2020 年 5 月 版权所有 © 2020 ASUSTeK COMPUTER INC. 保留所有权利。 除了购买者出于备份目的而保留的文档外,未经 ASUSTeK COMPUTER INC.
目录 声明 ...............................................................................................iv 安全信息 .............................................................................................v 保养和清洁 ........................................................................................vi Takeback Services .........................................................................vii 第 1 章: 产品介绍 1.1 欢迎使用! ...........................................................................1-1 1.
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作 的干扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规 定。这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产 生、使用并且辐射无线电波,如果不按照说明进行安装和使用,可能会对无 线电通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干扰如 果本设备确实对无线电或电视接收造成了有害干扰(可通过关闭和打开设备 电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电 / 电视技术人员咨询以获得帮助。 需要使用屏蔽线连接显示器和图形卡以确保符合 FCC 规定未经负责标 准遵守的责任方明确准许的变更或改造可能会使用户失去操作本设备的 权利。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳显示器内部有危险高压,可能导致严重人身伤害。 • 电源发生故障时,不要尝试自行修复请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏如有 任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的不要堵塞这些开口除非通风良 好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 不要使电源板或延长线过载过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度不要将显示器放置在可能受潮的任何区域中 将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线这样做可以防止 因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为确保正常运行,本显示器
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线采用正确的提 起方式放置显示器提起或搬运显示器时,抓住显示器的边缘不要通过底 座或线缆提起显示屏。 • 清洁关闭显示器电源并拔掉电源线使用不含麻且非研磨性的布清洁显示 器表面将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂使用显示器专用清洁剂切勿直接将清 洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁关闭电源开关,然 后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的图案桌面有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像屏 幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵循这些信息。 注:这些
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com。 2. 可选文档 您的经销商可能在您的产品包装中添加了可选文档这些文档不是标准 产品包装的组成部分。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.
viii
1.1 欢迎使用! 感谢您购买 ASUS® LCD 显示器! 这是 ASUS 最新推出的宽屏 LCD 显示器,它不但提供更宽、更亮、更清晰 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.
1.3 显示器简介 1.3.1 前部概览 1 VG27AQL1A 2 3 VG27AQ1A 4 5 ( 1. 打开 OSD 菜单。激活所选的 OSD 菜单项。 • 提高/降低值或上/下/左/右移动选项。 • 当显示器进入待机模式或显示“无信号”信息时显示输入选 择栏。 按钮 2. • 退出 OSD 菜单项。 • 当显示器进入待机模式或显示“无信号”信息时显示输入选 择栏。 • 长按 5 秒钟即可开启和关闭按键锁功能。 快捷方式 1 按钮: 3. • 默认:GamePlus。 • 要更改快捷方式功能,请转到 MyFavorite > 快捷方式 > 快捷方式 1 菜单。 • 当显示器进入待机模式或显示“无信号”信息时显示输入选 择栏。 • 默认: GameVisual。 • 要更改快捷方式功能,请转到 MyFavorite > 快捷方式 > 快捷方式 2 菜单。 • 当显示器进入待机模式或显示“无信号”信息时显示输入选 择栏。 快捷方式 2 按钮: 4.
电源按钮/电源指示灯 5. • 打开/关闭显示器电源。 • 下表介绍电源指示灯的颜色定义。 1.3.2 状态 描述 白色 琥珀色 熄灭 开机 待机模式/无信号 关机 后部概览 VG27AQ1A 4 5 9 4 5 6 10 VG27AQL1A 10 7 8 9 1. DC-IN 接口。此端口连接电源线。 2. HDMI 端口。此端口用于连接 HDMI 兼容设备。 3. HDMI 端口。此端口用于连接 HDMI 兼容设备。 4. DisplayPort。此端口用于连接 DisplayPort 兼容设备。 5. 耳机插口。此端口仅在连接 HDMI/DisplayPort 线时可用。 6. 此端口仅用于维修。(USB A 型) 7. USB B 型。此端口用于连接 USB 上行线缆。通过该线缆使用显示器 上的 USB 端口。 8.
Kensington 锁槽。 9. 10. 控制按钮。 GamePlus 功能 1.3.3 GamePlus 功能提供了一个工具包,并为用户在玩不同类型的游戏时创建一 个更好游戏环境。您有 6 个不同的十字瞄准线选项,可针对所进行的游戏 来选择最合适的选项。您还可将屏幕定时器置于显示器的左面,以便您掌握 游戏的进行时间;而 FPS(每秒帧数)计数器可让您了解游戏运行的顺利 程度。“显示对齐”显示了屏幕 4 侧的校准线,让您轻松方便地将多个显 示器完美对齐。狙击手功能(仅在设备上的 HDR 禁用时可用)为第一人称 射击而制定。 您可选择放大比率和按顺序排列的类型。 激活 GamePlus: 1. 按 GamePlus 热键。 2. 上/下移动 3. 按 ( ) 按钮或向右移动 ( ) 按钮可确认您选择的功能, 上/下移动 ( ) 按钮可在设置中导航。向左移动 ( ) 按钮可 返回、关闭和退出。 4.
1.3.
1-6 第 1 章:产品介绍
2.1 安装显示器支撑臂/底座 安装显示器底座: 1. 将显示器正面朝下置于桌上。 2. 将底座装到支撑臂上,确保支撑臂上的弹片进入底座上的凹槽。 3. 通过拧紧附带的螺丝,将底座固定到支撑臂上。 我们建议您在桌面上铺上软布,以免损坏显示器。 VG27AQ1A 1 2 2 1 VG27AQL1A 1 2 1 2 底座螺丝大小: M6 x 16.
2.2 调整显示器 • 为取得最佳观看效果,我们建议您面对显示器,将其调整至您感觉最舒 适的角度。 • 调整显示器角度时,按住底座,以免显示器掉落。 • VG27AQ1A:推荐调整角度为 +20° 到 -5°(倾斜)/+20° 到 -20°(旋 转)。 • VG27AQL1A:推荐调整角度为 +20° 到 -5°(倾斜)/+20° 到 -20°(旋 转)/ ±130 mm (高度调整)/90°(纵向视图)。 VG27AQ1A -5°~ +20° 20° VG27AQL1A 0° 20° -5°~ +20° 130mm 20° (倾斜) 0° (旋转) 20° (高度调整) 调整视角时显示器可能会略微抖动,这是正常现象。 转动显示器 (仅限VG27AQL1A) 2-2 1. 将显示器提升至最高位置。 2. 将显示器倾斜至最大角度。 3.
-5°~ +20° 0° 0° 90° 90° 调整视角时显示器可能会略微抖动,这是正常现象。 2.3 卸下支撑臂/底座(VESA 壁挂安装时) 此显示器的可拆卸支撑臂/底座是专为 VESA 壁挂安装而设计的。 要卸下支撑臂/底座: 1. 将显示器正面朝下放在桌子上。 2. 取下四个螺丝孔中的橡胶块。(图1) 3. 卸下底座(图2)。 4.
2.
2.5 连接线缆 按如下所述连接线缆: VG27AQ1A VG27AQL1A 仅用于维修 • • 连接电源线: a. 将电源适配器的一端牢固插入显示器上的直流输入接口。 b. 将电源线的一端连接到电源适配器,将另一端连接到电源插座。 连接 DisplayPort/HDMI 线: a. 将 DisplayPort/HDMI 线的一端连接到显示器的 DisplayPort/HDMI 端口。 b. 将 DisplayPort/HDMI 线的另一端连接到计算机的 DisplayPort/ HDMI 接口。 • 使用耳机:当有 HDMI 或 DisplayPort 信号输入时,将插头型的一端连 接到显示器的耳机插口。 • 使用 USB 3.0 端口:取出随产品提供的 USB 3.0 线,将 USB 上行线较 小的一端(B 型)插入显示器的 USB 上行端口,将较大一端(A 型) 插入电脑的 USB 3.0 端口。请确认您的电脑已安装最新的 Windows 7/ Windows 8.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 ASUS TUF Gaming VG27AQL1A HDR Off 比赛模式 DisplayPort 2560x1440@ 60Hz 游戏 超频 Ove rD rive A d a ptive-S ync (D P ) E L MB S Y N C Ga meP lus Ga meV isual S h a dow B oost 1. 按 2. 上/下移动 ( ) 按钮显示 OSD 菜单。 ( ) 按钮以在菜单功能中导航。选中所需的功能并按 ) 按钮可激活它。如果所选的功能有子菜单,上/下移动 ( ) 按钮以 在子菜单功能中导航。高亮显示所需的子菜单功能,然后按 ( ) 按钮或 ( 向右移动 ( ) 按钮以激活该功能。 3. 上/下移动 ( ) 按钮可更改所选功能的设置。 4. 如要退出并保存 OSD 菜单,请反复按 按钮或向左移动 OSD 菜单消失。如要调整其它功能,请重复步骤 1-3。 3.1.2 1.
• 超频: * 开:此功能可让您调整刷新率。 * 最大刷新率:让您选择 170 Hz 最大刷新率(仅适用于 DisplayPort 输入)。选择后,按 ( ) 按钮可激活设置。 超频可能造成屏幕抖动。要降低此效应,请断开 DisplayPort 线并使用显示器 OSD 菜单再次尝试使用更安全的最大刷新速率。 • OverDrive:提高 LCD 面板的灰阶响应时间。 此功能无法在启用 ELMB / ELMB SYNC 后可用。 • • Adaptive-Sync (DP) / Variable Refresh Rate:允许支持 Adaptive-Sync* 的图形源根据典型的内容帧速率动态调整显示刷新率以获得节能、真正流 畅和低延迟显示更新。 • 对于 HDMI,Adaptive-Sync (DP) / Variable Refresh Rate 只能在 48Hz 与 144Hz 内激活 Adaptive-Sync,对于 DisplayPort,只能在 48Hz 与 170Hz 内激活。 • 要了解支持的 GPU、最低 PC 系统和驱动程序要求,请联系 GPU 制造商。 ELMB
• Shadow Boost:暗色增强可调整显示器的伽玛曲线,以改善图像中的暗 色调,使暗色场面和对象更易看清。 此功能仅在比赛模式、RTS/RPG 模式、FPS 模式或 sRGB 模式下可用。 图像 2.
• 画面控制:将画面比例调整为全屏幕或 4:3。 Adaptive-Sync或HDR启用时此功能不可用。 • 滤蓝光 * 0 级:无更改。 * 1~4 级:级别越高,蓝光散射越少。当滤蓝光被激活后,比赛模式 的默认设置将自动导入。在 1 级至 3 级,亮度功能均为用户可配 置。4 级为优化设置。它符合 TUV 低蓝光认证。亮度功能用户不 可配置。 请参见以下内容以减轻眼睛疲劳: • 如果长时间工作,用户应离开显示屏一段时间。建议在电脑上连续工作 1 小时后休息一会(至少 5 分钟)。频繁的短暂休息比一次较长时间的休息 更有效。 • 要最大限度地减轻眼睛疲劳和眼睛干涩,用户应让眼睛定期聚焦于远处的物 体。 • 眼保健操有助于降低眼睛疲劳。经常重复做这些眼保健操。如果眼睛依然疲 劳,请咨询医师。眼保健操:(1) 重复向上向下看 (2) 慢慢转动眼睛 (3) 斜 向移动眼睛。 • 高能蓝光可能会导致眼睛疲劳和 AMD(老年黄斑病变)。滤蓝光可降低 70%(最高)有害蓝光以避免 CVS(电脑视觉综合症)。 色彩 3.
• 饱和度:调整范围是 0 到 100。 • 肤色:包含三种颜色模式,分别是红润色、自然色和黄艳色。 输入选择 4. 在此功能中,您可选择所需的输入源。 输入选择 ASUS TUF Gaming VG27AQL1A HDR Off 比赛模式 DisplayPort 2560x1440@ 60Hz H D MI-1 H D MI-2 D i splayP ort 5.
系统 6.
3.2 规格摘要 VG27AQL1A 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 色温选择 模拟输入 数字输入 耳机插口 音频输入 扬声器(内置) USB 3.0 端口 颜色 电源 LED 倾斜 枢轴旋转 旋转 高度调整 VESA 壁挂安装 Kensington 防盗锁 额定电压 温度(运行时) TFT LCD 27"(16:9, 68.5 cm)宽屏幕 2560 x 1440 0.2331 mm x 0.2331 mm 350 cd/m2, 400 cd/m2 (HDR 开启时) 1000:1 100,000,000:1(ASCR 开启时) 178˚/178˚ 1.073 G 3 ms(灰阶响应时间), 1ms MPRT 4 种色温 无 HDMI v2.0 x 2,DisplayPort v1.
多语言 附件 合规与标准 21 种语言(英文、法文、德文、意大利文、西班 牙文、荷兰文、葡萄牙文、俄文、捷克文、克罗 地亚文、波兰文、罗马尼亚文、匈牙利文、土耳其 文、简体中文、繁体中文、日文、韩文、泰文、印 度尼西亚文、波斯文) 快速入门指南、保修卡、电源适配器、电源线、 DisplayPort 线(选配)、HDMI 线(选配)、 USB 线(选配) cTUVus、CB、CE、ErP、FCC、CCC、CU、 RCM、BSMI、VCCI、RoHS、J-MOSS、 WEEE、Windows 7 & 10 WHQL、CEL、MEPS、 PSE、UkrSEPRO、KCC、E-Standby、 TUV-Flicker Free、TUV-Low Blue Light、 ICES-3、PC Recycle、BIS、PSB、Vietnam Energy、CEC *规格可能会随时变更,恕不另行通知。 **在屏幕亮度 200 尼特而无音频/USB/读卡器连接的情况下测量。 3-8 第 3 章:一般说明
VG27AQ1A 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 色温选择 模拟输入 数字输入 耳机插口 音频输入 扬声器(内置) USB 3.0 端口 颜色 电源 LED 倾斜 枢轴旋转 旋转 高度调整 VESA 壁挂安装 Kensington 防盗锁 额定电压 温度(运行时) TFT LCD 27"(16:9, 68.5 cm)宽屏幕 2560 x 1440 0.2331 mm x 0.2331 mm 250 cd/m2 1000:1 100,000,000:1(ASCR 开启时) 178˚/178˚ 1.073 G 3 ms(灰阶响应时间), 1ms MPRT 4 种色温 无 HDMI v2.0 x 2,DisplayPort v1.2 x 1 有 无 2 W x 2 立体声、RMS 无 黑色 白色(开机)/ 琥珀色(待机) +20˚~ -5˚ 无 +20˚~ -20˚ 无 100 x 100 mm 有 交流:100~240 V 直流:19 V、3.
附件 合规与标准 快速入门指南、保修卡、电源适配器、电源线、 DisplayPort 线(选配)、HDMI 线(选配) cTUVus、CB、CE、ErP、FCC、CCC、CU、 RCM、BSMI、VCCI、RoHS、J-MOSS、 WEEE、Windows 7 & 10 WHQL、CEL、MEPS、 PSE、UkrSEPRO、KCC、E-Standby、 TUV-Flicker Free、TUV-Low Blue Light、 ICES-3、PC Recycle、BIS、PSB、Vietnam Energy、CEC *规格可能会随时变更,恕不另行通知。 **在屏幕亮度 200 尼特而无音频/USB/读卡器连接的情况下测量。 3-10 第 3 章:一般说明
3.
VG27AQ1A 3-12 第 3 章:一般说明
3.
3.
视频时序 分辨率频率 HDMI DP 刷新率 刷新率 720x480P 59.94Hz 不支持 720x480P 60Hz 不支持 720x576P 50Hz 50Hz 1280x720P 50Hz 50Hz 1280x720P 59.94Hz 59.94Hz 1280x720P 60Hz 60Hz 1440x480P 不支持 59.94Hz 1440x480P 60Hz 60Hz 1440x576P 50Hz 50Hz 1920x1080P 30Hz 不支持 1920x1080P 50Hz 50Hz 1920x1080P 59.94Hz 59.