VG32VQ1B/VG32VQ1BR 系列 液晶显示器 用户指南
目录 声明 .....................................................................................iii 安全信息................................................................................iv 保养和清洁 ............................................................................vii 1.1 欢迎使用! ....................................................................................... ix 1.2 物品清单 ........................................................................................... ix 1.3 组装显示器 ........................
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、 使用并且辐射无线电波,如果不按照制造商的说明进行安装和使用,可能会 对无线电通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干 扰。如果本设备对无线电或电视接收造成了有害干扰(可通过关闭和打开设 备电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电噪 声发射 B 级限制。 此 B 级数字设备符合加拿大 ICES-003 的要求。 设备一旦掉落,可能导致严重的人身伤害甚
安全信息 iv • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身伤 害。 • 电源发生故障时,不要尝试自行修复。请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。如 有任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。不要堵塞这些开口。除非通 风良好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 请勿使电源板或延长线过载。过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。不要将显示器放置在可能受潮的任何区域 中。将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以防 止因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。
• 请确认在建筑物中安装时配电系统应提供额定值为120/240V、20A (最大)的断路器。 • 如果电源线提供3插片的插头,请将电源线插入接地的3孔插座。请勿禁 用电源线的接地插片,例如,连接2插片适配器。接地插片是重要的安 全措施。 稳定性危害 • 此产品一旦掉落,可能导致严重的人身伤害甚至死亡。为避免伤害,此 产品必须依照安装说明牢固地安装到地板/墙壁上。 • 产品一旦掉落,可能导致严重的人身伤害甚至死亡。为了避免许多伤害 (特别是对孩童的伤害),可以采取一些简单的预防措施,例如: • 务必使用产品制造商推荐的机柜或架子或安装方法。 • 务必使用能够安全支撑此产品的家具。 • 切勿让此产品悬在支撑家具的边缘。 • 务必向孩童说明关于攀爬家具以接触此产品或其控制的危险。 • 务必合理布放连接到此产品的线缆,以免线缆绊人或者被拉扯或挤压。 • 切勿将此产品放在不稳定的地方。 • 切勿将此产品放置在高大的家具上(例如,橱柜或书柜),除非家具和 产品都固定在合适的支架上。 • 切勿在此产品和支撑家具之间放置布或其他物品, • 切勿将玩具和遥控器等可能吸引儿童攀爬
防止倾倒 使用显示器时,为防止显示器掉落,应使用可以支撑显示器重量的绳索或链条将 LCD固定在墙上。 1 M4或M6螺丝 绳索 2 绳索或链条 vi • 显示器设计可能与图示有所不同。 • 安装必须由专业技术人员完成,请联系您的供应商以获取更多信 息。 • 对于净重>=7kg的型号。请选择合适方法以防止倾倒。 • 对于带有VESA安装架的型号,请使用方法 ,将带环的螺丝安装 到VESA安装架孔中,然后将绳索或链条固定在墙上。否则,请 使用方法 将绳索或链条固定在支架上,然后将其固定在墙上。
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的 提起方式放置显示器。提起或搬运显示器时,抓住显示器的边缘。不要 通过底座或线缆提起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁 显示器表面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。使用液晶专用清洁剂。切勿直接将 清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。关闭电源开关, 然后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理。不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵循
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 viii 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com 2.
1.1 欢迎使用! 感谢您购买 ASUS® 液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.
1.3 组装显示器 组装显示器: • 在安装显示器支撑臂/底座时,我们建议您将显示器放在其EPS(发泡聚苯乙 烯)包装内进行。 1. 将支撑臂上的螺丝孔对准底座上附带的螺丝。然后,将底座插入支撑 臂。 2.
1.4 连接线缆 1.4.1 液晶显示器后部 6 1-2 ~ HDMI-2 HDMI-1 5 4 3 1. 耳机输出端口 2. DP输入端口 3. HDMI-1 端口 4. HDMI-2 端口 5. 交流电源输入端口 6.
1.5 显示器简介 1.5.1 使用控制按钮 使用显示器底部的控制按钮调整图像设置。 6 6 5 5 4 4 3 3 2 2 1 1. 电源指示灯: • 2. 下表介绍电源指示灯的颜色定义。 状态 说明 白色 开机 黄色 待机模式 关闭 关闭 电源键: • 按此按钮打开/关闭显示器的电源。 • 利用此热键,可以切换采用GameVisual™视频智能技术的7种视频预 设模式(风景模式、比赛模式、影院模式、RTS/RPG模式、FPS模式 、sRGB模式和MOBA模式)。 3. GameVisual按钮: 4.
• 激活十字瞄准线、定时器、FPS 计数器或显示对齐功能。 • 向上/向下移动 ( )按钮进行选择,然后按 能。按 离开和退出。 • 十字瞄准线/定时器/FPS 计数器可以通过按 GamePlus- 主菜单 ( )确认所需的功 5向键进行移动。 GamePlus-十字瞄准线 GamePlus-定时器 GamePlus 十字瞄准线 (练习模式) 定时器 FPS FPS 计数器 显示对齐 5. 关闭按钮: • 退出OSD菜单。 • • (5向) 按钮: 开启OSD菜单。激活所选的 OSD 菜单项目。 增加/减小值或向上/下/左/右移动选择 6.
2.
2.2 卸下支撑臂/底座(VESA 壁挂安装时) 此显示器的可拆卸底座是专为 VESA 壁挂安装而设计的。 卸下支撑臂/底座 2-2 1. 拔掉电源线和信号线。小心地将显示器正面朝下放在其EPS包装上。 2. 取下螺丝盖。 3. 取下用于将支撑臂固定在显示器后部的四(4)个螺丝。 4. 从显示器上卸下底座(支撑臂和底座)。 • VESA 壁挂套件 (100 x 100 mm) 需另外购买。 • 仅使用取得UL认证的壁挂装配架,最小重量/承重28.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 游戏 ASUS TUF 游戏 VG32VQ1B HDR OFF 比赛模式 DisplayPort 2560x1440@60Hz OverDrive FreeSync Premium ELMB GamePlus GameVisual 阴影增强 1. 按5向按钮的中间位置以激活OSD菜单。 2. 按和按钮切换菜单中的选项。在从一个图标移到另一个图标时, 选项名称高亮显示。 3. 若要选择菜单中高亮显示的项目,请按下中心按钮。 4. 按和按钮选择所需的参数。 5. 按下中心按钮进入滑动条,然后使用或按钮(视菜单中的指示器 而定)进行更改。 6.
3.1.2 1.
2.
请参考下述说明以缓解眼睛疲劳: 3.
4. 输入选择 选择输入源:HDMI-1、HDMI-2 或 DisplayPort 输入信号。 输入选择 ASUS TUF 游戏 VG32VQ1B HDR OFF 比赛模式 DisplayPort 2560x1440@60Hz HDMI-1 HDMI-2 DisplayPort 5. MyFavorite 加载 / 保存显示器的所有设置。 MyFavorite ASUS TUF 游戏 VG32VQ1B HDR OFF 比赛模式 DisplayPort 2560x1440@60Hz 快捷方式 自定义设置 6.
系统 ASUS TUF 游戏 VG32VQ1B HDR OFF 比赛模式 DisplayPort 2560x1440@60Hz 恢复出厂模式 3-6 • 语言: 选择 OSD 语言。选项包括:英语、法语、德语、西班牙语、意大 利语、荷兰语、俄语、波兰语、捷克语、克罗地亚语、匈牙利语、罗马尼 亚语、葡萄牙语、土耳其语、简体中文、繁体中文、日语、朝鲜语、波斯 语、泰语和印度尼西亚语。 • 声音: 调整输出音量大小。 • ECO Mode: 激活经济模式以达到省电目的。 • 电源指示灯: 使电源 LED 指示灯点亮/熄灭。 • 电源键锁: 禁用/启用电源键。 • 按键锁: 禁用所有按键功能。按住向下按钮五秒以上可以禁用按键锁功能。 • 菜单设置: 调整OSD画面的菜单时间、DDC/CI和透明度。 • 显示信息: 显示关于显示器的信息。 • 恢复出厂模式: 选择“是”时,所有设置恢复至出厂默认模式。 第 3 章:一般说明
3.2 规格 型号 VG32VQ1B 面板尺寸 31.5” W (80.1cm) 最大分辨率 2560x1440@165Hz 亮度(典型) 固有对比度(典型) 视角 (CR=10) 250cd/m2 3000:1 178°(垂直)/178°(水平) 显示颜色数 16.7 M(真正8位) 颜色饱和度 85% NTSC 响应时间 卫星扬声器 4ms(灰色到灰色),1ms MPRT 2W x 2立体声 耳机输出 是 来自 HDMI 的声音 是 HDMI 输入 是 DisplayPort 输入 是 开机功耗(最大) < 40 W* 机壳颜色 黑色 省电模式 < 0.5W 关机模式 倾斜 < 0.5W -5° ~ +20° 物理尺寸 (WxHxD) 709.7 x 507.11 x 213.78 mm 包装尺寸 (WxHxD) 810 x 602 x 226 mm 净重(约) 毛重(估计) 7.5 kg 11.
3.
3.4 支持的时序列表 HDMI2.0 输入的PC时序表 分辨率 HDMI(2.