Motherboard TUF GAMING Z590-PLUS
E18029 Revised Edition v2 January 2021 Copyright © 2021 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Safety information....................................................................................................... iv About this guide........................................................................................................... v TUF GAMING Z590-PLUS specifications summary.................................................. vi Connectors with shared bandwidth........................................................................... x Package contents.............................
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product Introduction This chapter describes the features of the motherboard and the new technology it supports. It includes description of the switches, jumpers, and connectors on the motherboard.
TUF GAMING Z590-PLUS specifications summary Intel® Socket LGA1200 for 11th Gen Intel® Core™ processors & 10th Gen Intel® Core™, Pentium® Gold and Celeron® Processors Supports Intel® 14 nm CPU CPU Supports Intel® Turbo Boost Technology 2.0 and Intel® Turbo Boost Max Technology 3.0** * Refer to www.asus.com for CPU support list. ** Intel® Turbo Boost Max Technology 3.0 support depends on the CPU types. Chipset Intel® Z590 Chipset 4 x DIMM, Max.
TUF GAMING Z590-PLUS specifications summary * Storage Ethernet Raid function for PCIe mode SSD in Intel® Rapid Storage Technology is available with either 1. Intel® SSDs installed in both CPU-attached and PCH-attached slots, or 2. any other 3rd party SSDs installed in PCH-attached slots. ** To enable Intel® Optane™ Memory (Hybrid Storage device), it must be installed in PCH-attached slots with Intel® Rapid Storage Technology. *** M.2_2 shares bandwidth with SATA6G_2. When M.
TUF GAMING Z590-PLUS specifications summary Fan and cooling-related 1 x 4-pin CPU Fan header 1 x 4-pin CPU OPT Fan header 1 x 4-pin AIO Pump header 3 x 4-pin Chassis Fan headers Power related 1 x 24-pin Main Power connector 1 x 8-pin +12V Power connector 1 x 4-pin +12V Power connector Storage related 3 x M.2 slots (Key M) Internal I/O Connectors 6 x SATA 6Gb/s ports USB 1 x USB 3.2 Gen 1 connector (supports USB Type-C®) 1 x USB 3.2 Gen 1 header supports additional 2 USB 3.2 Gen 1 ports 2 x USB 2.
TUF GAMING Z590-PLUS specifications summary ASUS Exclusive Software Features Armoury Crate - AURA Creator - AURA Sync - Two-Way AI Noise Cancelation AI Suite 3 - Performance And Power Saving Utility TurboV Evo EPU DIGI + VRM Fan Xpert 4 Software Features - EZ update TUF GAMING CPU-Z AI Charger ASUS Turbo LAN DAEMON Tools DTS Custom for GAMING Headsets Norton Anti-virus software (Free Trial version) WinRAR UEFI BIOS ASUS EZ DIY - ASUS CrashFree BIOS 3 - ASUS EZ Flash 3 - ASUS UEFI BIOS EZ Mode BIOS 192 (1
Connectors with shared bandwidth RGB_HEADER2 CPU_FAN CPU_OPT KBMS _USB1112 ATX_12V_2 ATX_12V_1 ADD_GEN 2_2 DIGI+ VRM ATX_PWR LGA1200 LAN_U32G2_34 BOOT VGA DRAM CPU U32G1_910 U32G1_78 DDR4 DIMM_B2* (64bit, 288-pin module) U32G2X2_1 DDR4 DIMM_B1 (64bit, 288-pin module) DDR4 DIMM_A1 (64bit, 288-pin module) HDMI _DP DDR4 DIMM_A2* (64bit, 288-pin module) ASM 1442K U32_5 AUDIO 2260 2280 22110 SATA6G_5 2242 PCIEX16_1 BATTERY 64Mb BIOS Intel® Z590 128Mb BIOS B SATA6G_6 Intel® I225-V
Package contents Check your motherboard package for the following items. Motherboard 1 x TUF GAMING Z590-PLUS motherboard Cables 2 x SATA 6Gb/s cables 2 x M.2 Rubber Packages Miscellaneous 1 x M.2 SSD screw package 1 x TUF Gaming sticker Installation Media Documentation 1 x Support DVD 1 x TUF Certification card 1 x User manual If any of the above items is damaged or missing, contact your retailer.
Installation tools and components Phillips (cross) screwdriver PC chassis Power supply unit Intel® LGA 1200 CPU Intel® LGA 1200 compatible CPU Fan DDR4 DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) M.2 SSD module (optional) 1 Bag of screws The tools and components in the table above are not included in the motherboard package.
Product Introduction Product Introduction 1.1 Before you proceed 1 Chapter 1 Chapter 1: Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
1.2 Motherboard layout 5 4 1 24.4cm(9.6in) 4 2 Chapter 1 RGB_HEADER2 CPU_FAN CPU_OPT KBMS _USB1112 ATX_12V_2 ATX_12V_1 12 11 ADD_GEN 2_2 DIGI+ VRM LAN_U32G2_34 BOOT VGA DRAM CPU 5 30.
TUF GAMING Z590-PLUS Page 1-4 1-5 1-7 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-19 1-20 1-21 1-21 Chapter 1 Layout contents 1. CPU socket 2. DIMM slots 3. Expansion slots 4. Fan and Pump headers 5. Power connectors 6. M.2 slots (SOCKET 3) 7. SATA 6Gb/s ports 8. USB 3.2 Gen 1 Front Panel connector 9. USB 3.2 Gen 1 header 10. USB 2.0 headers 11. AURA Addressable Gen2 headers 12. AURA RGB headers 13. Clear CMOS header 14. COM Port header 15. Front Panel Audio header 16. System Panel header 17.
1. CPU socket The motherboard comes with a LGA1200 socket designed for 11th Gen Intel® Core™ processors & 10th Gen Intel® Core™, Pentium® Gold and Celeron® Processors. Chapter 1 LGA1200 1-4 • Ensure that you install the correct CPU designed for LGA1200 socket only. DO NOT install a CPU designed for other sockets on the LGA1200 socket. • The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU.
2. DIMM slots The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR4 (Double Data Rate 4) memory modules. Chapter 1 DIMM_B2* DIMM_B1 DIMM_A2* DIMM_A1 A DDR4 memory module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
Memory configurations You may install 1 GB, 2 GB, 4 GB, 8 GB, 16 GB, and 32 GB unbuffered and non‑ECC DDR4 DIMMs into the DIMM sockets. Chapter 1 You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
3. Expansion slots Chapter 1 Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
Recommended VGA configuration Chapter 1 1. 3. Slot Description PCIe 4.0 x16_1 PCIe 3.0 x16_2 Single VGA x16 - Dual VGA x16 x4 Connect a chassis fan to the chassis fan connectors when using multiple graphics cards for better thermal environment. PCIe bifurcation & M.2 settings in PCIe x16 slots (from CPU) PCIe bifurcation & M.2 settings in PCIe x16 slots (from CPU) Slot Description Quantity of identifiable Intel M.2 SSD (pcs) PCIe 4.0 x16_1 3 (x8+x4+x4) M.
4. Fan and Pump headers AIO_PUMP D CHA_FAN1 E CHA_FAN2 F CHA_FAN3 C D GND C FAN PWM FAN IN FAN PWR CPU_OPT GND FAN PWR FAN IN FAN PWM FAN PWR FAN IN FAN PWM CPU_FAN B GND A A B Chapter 1 The Fan and Pump headers allow you to connect fans or pumps to cool the system. E F Header CPU_FAN CPU_OPT CHA_FAN1 CHA_FAN2 CHA_FAN3 AIO_PUMP • DO NOT forget to connect the fan cables to the fan headers. Insufficient air flow inside the system may damage the motherboard components.
5. Power connectors These Power connectors allow you to connect your motherboard to a power supply. The power supply plugs are designed to fit in only one orientation. Find the proper orientation and push down firmly until the power supply plugs are fully inserted.
6. M.2 slots C M.2_1(SOCKET3) M.2_3(SOCKET3) B M.2_2(SOCKET3) A A Chapter 1 The M.2 slots allow you to install M.2 devices such as M.2 SSD modules. B C • M.2_1 slot (Key M), type 2242/2260/2280/22110. (Only Intel® 11th Gen processors support PCIe 4.0 x4 mode, this slot will be disabled for other CPUs) • M.2_2 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 3.0 x4 & SATA modes). • M.2_3 slot (Key M), type 2242/2260/2280 (supports PCIe 3.0 x4 & SATA modes). • M.
7. SATA 6Gb/s ports The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and hard disk drives via SATA cables.
8. USB 3.2 Gen 1 Front Panel connector Chapter 1 The USB 3.2 Gen 1 connector (supports USB Type-C®) allows you to connect a USB 3.2 Gen 1 module for an additional USB 3.2 Gen 1 Type-C® port. The USB 3.2 Gen 1 connector provides data transfer speeds of up to 5 Gb/s. U32_5 SBU2 SBU1 CC1 VBUS RX1RX1+ GND TX1TX1+ VBUS VBUS TX2+ TX2GND RX2+ RX2GND DD+ CC2 The USB 3.2 Gen 1 module is purchased separately.
9. USB 3.2 Gen 1 header The USB 3.2 Gen 1 header allows you to connect a USB 3.2 Gen 1 module for additional USB 3.2 Gen 1 ports. The USB 3.2 Gen 1 header provides data transfer speeds of up to 5 Gb/s. Chapter 1 U32G1_910 A PIN 1 USB3+5V IntA_P2_SSRXIntA_P2_SSRX+ GND IntA_P2_SSTXIntA_P2_SSTX+ GND IntA_P2_DIntA_P2_D+ USB3+5V IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ GND The USB 3.2 Gen 1 module is purchased separately. The plugged USB 3.
10. USB 2.0 header USB_E12 PIN 1 USB_E34 PIN 1 A B USB+5V USB_P4USB_P4+ GND USB+5V USB_P3USB_P3+ GND NC B USB+5V USB_P2USB_P2+ GND USB+5V USB_P1USB_P1+ GND NC A Chapter 1 Connect the USB module cable to these connectors, then install the module to a slot opening at the front of the system chassis. These USB headers comply with USB 2.0 specifications and support up to 480 Mbps connection speed. DO NOT connect a 1394 cable to the USB connectors.
11. AURA Addressable Gen2 headers The Addressable Gen2 headers allow you to connect individually addressable RGB WS2812B LED strips or WS2812B based LED strips. ADD_GEN 2_2 ADD_GEN 2_1 +5V Data B Ground Chapter 1 A A PIN 1 B The Addressable Gen2 headers support WS2812B addressable RGB LED strips (5V/ Data/Ground), with a maximum power rating of 3A (5V), and the addressable headers on this board can handle a combined maximum of 500 LEDs.
12. AURA RGB LED headers The AURA RGB LED headers allow you to connect RGB LED strips. RGB_HEADER2 Chapter 1 A A PIN 1 +12V G R B B RGB_HEADER1 B R G +12V PIN 1 B The AURA RGB LED headers support 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum power rating of 3A (12V). Before you install or remove any component, ensure that the power supply is switched off or the power cord is detached from the power supply.
13. Clear CMOS header Chapter 1 This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. +3V_BAT GND CLRTC PIN 1 To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Use a metal object such as a screwdriver to short the two pins.
14. COM Port header Chapter 1 This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. PIN 1 DCD TXD GND RTS RI RXD DTR DSR CTS COM The COM module is purchased separately. 15. Front Panel Audio header The front panel audio header is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this header.
16. System Panel header The System Panel header supports several chassis-mounted functions. Chapter 1 +5V Ground Ground Speaker Intruder# PLED+ PLEDPWRBTN# GND PLED PWRSW SPEAKER CHASSIS PANEL GND PLED- HDD_LED+ HDD_LEDGround RSTCON# NC PLED+ PIN 1 HDD_LED RESET PLED • System Power LED header (PLED) The 2-pin header allows you to connect the System Power LED.
17. ThunderboltTM header I2C_SCL I2C_SDA I2C_IRQ# RTD3_POWER_EN S_SLP_S0#_IDLE PERST_N WAKE# Chapter 1 The ThunderboltTM header allows you to connect an add-on ThunderboltTM I/O card that supports Intel’s ThunderboltTM Technology, allowing you to connect Thunderbolt™-enabled devices to form a daisy chain-configuration. TB_HEADER 18. RTD3_SW FORCE_PWR GND SLP_S3# SLP_S5# GND PIN 1 • The add-on ThunderboltTM I/O card and ThunderboltTM cables are purchased separately.
Chapter 1 1-22 Chapter 1: Product Introduction
Chapter 2: Basic Installation Basic Installation 2.1 Building your PC system 2 The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. CPU installation • Ensure that you install the correct CPU designed for LGA1200 socket only. DO NOT install a CPU designed for LGA1155, LGA1156, and LGA1151 sockets on the LGA1200 socket.
Chapter 2 2-2 Chapter 2: Basic Installation
2.1.2 Cooling system installation Apply Thermal Interface Material to the CPU cooling system and CPU before you install the cooling system, if necessary.
To install an AIO cooler If you wish to install an AIO cooler, we recommend installing the AIO cooler after installing the motherboard into the chassis.
DIMM installation Chapter 2 2.1.
2.1.4 M.2 installation Supported M.2 type varies per motherboard. • The illustrations only show the installation steps for a single M.2 slot, the steps are the same for the other M.2 slots if you wish to install an M.2 to another M.2 slot. • Use a Phillips screwdriver when removing or installing the screws or screw stands mentioned in this section. • The M.2 is purchased separately. When installing an M.2 to the M.2 slot, you may need to use the removable screw stand. Chapter 2 1.
3. Install your M.2 to your M.2 slot. For M.2_1 • To install an M.2 to the maximum length For M.2_1: Type 22110 M.2 (optional) Remove the pre-installed removable M.2 Q-Latch screw at the 2280 length screw hole. B. Rotate and adjust the M.2 Q-latch so that the handle points away from the M.2 slot. C. Install your M.2 to the M.2 slot. D. Rotate the M.2 Q-Latch clockwise to secure the M.2 in place. Chapter 2 A.
• To install an M.2 using the removable M.2 Q-Latch screw For M.2_1: Type 2242, 2260, 2280 M.2 A. (optional) Remove the M.2 rubber pad. Follow this step only if you wish to install an M.2 to type 2242. Chapter 2 2-8 B. (optional) If required, remove the pre-installed removable M.2 Q-Latch screw at the 2280 length screw hole. C. Install the M.2 Q-Latch to the M.2 length screw hole you wish to install your M.2 to. D. Rotate and adjust the M.2 Q-latch so that the handle points away from the M.2 slot.
For M.2_2 and M.2_3 The steps may differ between installing M.2 of different lengths, please refer to the different types and their installation steps below: • To install an M.2 to the maximum length the M.2 slot supports For M.2_2: Type 22110 M.2 A. Install your M.2 to the M.2 slot. B. Rotate the M.2 Q-Latch clockwise to secure the M.2 in place. • To install an M.2 using the removable screw stand Chapter 2 For M.2_3: Type 2280 M.2 For M.2_2: Type 2242, 2260, 2280 M.2 For M.2_3: Type 2242, 2260 M.
4. Remove the plastic film from the thermal pads on the bottom of the heatsink. 5. Replace the heatsink. 6. Secure the heatsink using the screws removed previously.
Motherboard installation 1. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel. 2. Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. Chapter 2 2.1.5 DO NOT over tighten the screws! Doing so can damage the motherboard.
2.1.6 ATX power connection Chapter 2 OR 2-12 AND • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power plugs.
2.1.
2.1.8 Front I/O connector To install the front panel header To install USB 3.2 Gen 1 connector (USB Type-C®) USB 3.2 Gen 1 (USB Type-C®) Chapter 2 This connector will only fit in one orientation. Push the connector until it clicks into place. To install USB 3.2 Gen 1 connector To install USB 2.0 connector USB 3.2 Gen 1 USB 2.
2.1.
To install ThunderboltTM series card 6-pin PCIe power connector USB Type-C® port connects to ThunderboltTM devices Chapter 2 MiniDP in port connects to DP out port on the motherboard or a VGA card USB 2.0 header Thunderbolt TM header Ensure to install the ThunderboltTM series card to a PCIe slot from PCH. 2-16 • Step 6 is optional, please connect a 6-pin PCIe power connector when you wish to use the USB Type-C® port ThunderboltTM quick charge feature to charge a 5V or more device.
Motherboard rear and audio connections 2.2.1 Rear I/O connection 1 5 2 3 4 6 7 8 9 10 Chapter 2 2.2 Rear panel connectors 1. 2. 3. 4. 5. 6. 7. PS/2 mouse/keyboard combo port DisplayPort USB 3.2 Gen 1 Type-A ports Ethernet (RJ-45) port* USB 2.0 Type-A ports HDMI™ port USB 3.2 Gen 2x2 port (USB Type-C®) 8. USB 3.2 Gen 2 Type-A ports 9. Optical S/PDIF OUT port 10. Audio jacks** * and ** : Refer to the tables on the next page for LAN port LEDs, and audio port definitions.
* Intel® I225-V 2.5Gb Ethernet port LED indications Activity Link LED Speed LED Status Description Status OFF No link OFF GREEN BLINKING Data activity GREEN BLINKING Data activity GREEN BLINKING Data activity ACT/LINK LED Description No link 100 Mbps / 10 Mbps OFF connection GREEN 2.5 Gbps connection ORANGE 1 Gbps connection SPEED LED LAN port ** Audio 2, 4, 5.1 or 7.1-channel configuration Port Chapter 2 Light Blue Lime Pink Orange Black 2.2.
Connect to Stereo Speakers Chapter 2 Connect to 2-channel Speakers Connect to 4-channel Speakers TUF GAMING Z590-PLUS 2-19
Connect to 5.1-channel Speakers Chapter 2 Connect to 7.
2.3 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Ensure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: Monitor b. External SCSI devices (starting with the last device on the chain) c.
Chapter 2 2-22 Chapter 2: Basic Installation
Chapter 3: BIOS and RAID Support BIOS and RAID Support 3 For more details on BIOS and RAID configurations, please refer to www.asus.com/ support. 3.1 Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system.
3.2 BIOS Setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screens include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup, press or during the Power-On Self Test (POST). If you do not press or , POST continues with its routines. Entering BIOS Setup after POST To enter BIOS Setup after POST: • Press ++ simultaneously.
3.4 ASUS EZ Flash 3 The ASUS EZ Flash 3 feature allows you to update the BIOS without using an OS‑based utility. Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu or press hotkey . To update the BIOS by USB: • This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only.
3.5 ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using a USB flash drive that contains the BIOS file. Recovering the BIOS 1. Download the latest BIOS version for this motherboard from https://www.asus.com/support/. 2. Rename the BIOS file as ASUS.CAP or TGZ590P.CAP and copy the renamed BIOS file to a USB flash drive. 3.
3.6 RAID configurations The motherboard comes with the Intel® Rapid Storage Technology that supports RAID 0, RAID 1, RAID 5 and RAID 10 configuration. For more information on configuring your RAID sets, please refer to the RAID Configuration Guide which you can find at https://www.asus.com/support, or by scanning the QR code. RAID definitions RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
Chapter 3 3-6 Chapter 3: BIOS and RAID Support
Appendix Appendix Notices FCC Compliance Information Responsible Party: Address: Phone / Fax No: Asus Computer International 48720 Kato Rd., Fremont, CA 94538, USA (510)739-3777 / (510)608-4555 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Google™ License Terms Copyright© 2021 Google Inc. All Rights Reserved. Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions. DO NOT throw the motherboard in municipal waste.
TUF GAMING Z590-PLUS Română ASUSTeK Computer Inc. declară că acest dispozitiv se conformează cerinţelor esenţiale şi altor prevederi relevante ale directivelor conexe. Textul complet al declaraţiei de conformitate a Uniunii Europene se găseşte la: www.asus.com/support Srpski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti sa osnovnim zahtevima i drugim relevantnim odredbama povezanih Direktiva. Pun tekst EU deklaracije o usaglašenosti je dostupan da adresi: www.asus.
Warranty EN: ASUS Guarantee Information • ASUS offers a voluntary manufacturer’s Commercial Guarantee. • ASUS reserves the right to interpret the provisions of the ASUS Commercial Guarantee. • This ASUS Commercial Guarantee is provided independently and in addition to the statutory Legal Guarantee and in no way affects or limits the rights under the Legal Guarantee. CR: Informacije o ASUS jamstvu • ASUS dragovoljno nudi komercijalno proizvođačko jamstvo.
PG: Informações de Garantia ASUS • A ASUS oferece uma Garantia Comercial voluntária do fabricante. • A ASUS reserva o direito de interpretar as disposições da Garantia Comercial da ASUS. • Esta Garantia Comercial da ASUS é fornecida de forma independente além da Garantia Legal estatutária e não afeta nem limita de qualquer forma os direitos estabelecidos na Garantia Legal. Para consultar todas as informações sobre a garantia, visite https://www.asus.com/pt/support/.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax Web site Technical Support Telephone Online support 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 https://www.asus.com +86-21-38429911 https://qr.asus.com/techserv ASUS COMPUTER INTERNATIONAL (America) Address Telephone Fax Web site Technical Support Support fax Telephone Online support 48720 Kato Rd.
