Motherboard TUF GAMING Z790-PRO WIFI
E23332 Revised Edition V2 January 2024 Copyright © 2024 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Safety information....................................................................................................... iv About this guide........................................................................................................... v TUF GAMING Z790-PRO WIFI specifications summary......................................... viii Package contents.......................................................................................................
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product Introduction This chapter describes the features of the motherboard and includes descriptions for each part of the motherboard. • Chapter 2: Basic Setup This chapter lists the basic setup procedures for setting up your motherboard.
4. Motherboard Installation Guide Please visit https://www.asus.com/support for more information on the Motherboard Installation Guide. 5. Driver and Utilities FAQ Please visit https://www.asus.com/support for more information on downloading and installing drivers and utilities for your motherboard. 6. RAID Configuration Guide Please visit https://www.asus.com/support for more information on the RAID Configuration Guide.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this user guide. CAUTION: Information to prevent damage to the components and injuries to yourself when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
TUF GAMING Z790-PRO WIFI specifications summary Intel® Socket LGA1700 for Intel® Core™ 14th & 13th Gen Processors, Intel® Core™ 12th Gen, Pentium® Gold and Celeron® Processors* CPU Supports Intel® Turbo Boost Technology 2.0 and Intel® Turbo Boost Max Technology 3.0** * Refer to www.asus.com for CPU support list. ** Intel® Turbo Boost Max Technology 3.0 support depends on the CPU types. Chipset Intel® Z790 Chipset 4 x DIMM slots, max.
TUF GAMING Z790-PRO WIFI specifications summary Ethernet 1 x Intel® 2.5Gb Ethernet TUF LANGuard Wi-Fi 6E 2x2 Wi-Fi 6E (802.11ax) Wireless & Bluetooth® Supports 2.4/5/6GHz frequency band* Bluetooth® v5.3** * WiFi 6GHz regulatory may vary between countries. ** The Bluetooth version may vary, please refer to the Wi-Fi module manufacturer’s website for the latest specifications.
TUF GAMING Z790-PRO WIFI specifications summary Fan and Cooling Related 1 x 4-pin CPU Fan header 1 x 4-pin CPU OPT Fan header 1 x 4-pin AIO Pump header 4 x 4-pin Chassis Fan headers Power Related 1 x 24-pin main power connector 2 x 8-pin +12V power connectors Storage Related 4 x M.2 slots (Key M) 4 x SATA 6Gb/s ports Internal I/O Connectors USB 1 x USB 20Gbps connector (supports USB Type-C®) 1 x USB 5Gbps header supports 2 additional USB 5Gbps ports 2 x USB 2.0 headers support 4 additional USB 2.
TUF GAMING Z790-PRO WIFI specifications summary - SafeDIMM Aura Sync - Aura RGB header Special Features - Addressable Gen 2 headers Front Panel USB 20Gbps with PD Fast Charge Support - Support: up to 30W fast charging and USB Wattage Watcher - Output: 5V/9V max. 3A, 12V max 2.5A - Compatible with PD3.
Package contents Check your motherboard package for the following items. Motherboard 1 x TUF GAMING Z790-PRO WIFI motherboard Cables 2 x SATA 6Gb/s cables 1 x ASUS WiFi Q-Antenna Miscellaneous 1 x TUF GAMING sticker 2 x M.2 rubber packages 1 x Screw package for M.2 SSD Documentation xii 1 x TUF certification card 1 x Quick start guide • If any of the above items is damaged or missing, contact your retailer.
Product Introduction Product Introduction 1.1 Before you proceed 1 Chapter 1 Chapter 1: Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
1.2 Motherboard layout 5 4 1 4 2 4 18 24.4cm(9.6in) CPU_OPT CPU DRAM VGA BOOT 12 6 M.2_1(SOCKET3) 2242 PCIE 4.0 X4 SATA IRST X V 2260 ADD_GEN 2_1 9 1st 22110 2280 8 30.5cm(12in) M.2_1(SOCKET3) Intel Ethernet CHA_FAN1 AUDIO 5 U20G_C5 M.2(WIFI) SATA6G_2 SATA6G_1 PCIEX16(G5) PCIEX16(G3) BATTERY PCIE 4.0 X4 2280 2260 V 2242 Super I/O 22110 IRST X M.2_2(SOCKET3) 2260 2280 SATA 2242 Audio Codec 2242 M.2_3(SOCKET3) PCIE 4.0 X4 7 6 M.
Motherboard User Manual Page 1-4 1-5 1-6 1-9 1-10 1-11 1-12 1-13 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 Chapter 1 Layout contents 1. CPU socket 2. DIMM slots 3. Expansion slots 4. Fan and Pump headers 5. Power connectors 6. M.2 slots 7. SATA 6Gb/s ports 8. USB 20Gbps Type-C® Front Panel connector 9. USB 5Gbps header 10. USB 2.0 headers 11. Addressable Gen 2 headers 12. Aura RGB header 13. Clear CMOS header 14. COM Port header 15. Front Panel Audio header 16. System Panel header 17.
1. CPU socket The motherboard comes with a LGA1700 socket designed for Intel® Core™ 14th & 13th Gen Processors, Intel® Core™ 12th Gen, Pentium® Gold and Celeron® Processors. Chapter 1 LGA1700 1-4 • Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the CPU socket.
2. DIMM slots Chapter 1 The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR5 (Double Data Rate 5) memory modules. A DDR5 memory module is notched differently from a DDR, DDR2, DDR3, or DDR4 module. DO NOT install a DDR, DDR2, DDR3, or DDR4 memory module to the DDR5 slot. Recommended memory configurations Memory configurations You may install Non-ECC DDR5 DIMMs into the DIMM sockets. • You may install varying memory sizes in the DIMM channels.
3. Expansion slots Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Chapter 1 To install a PCIe expansion card, please refer to the Motherboard Installation Guide on the ASUS support site.
Please refer to the following tables for the recommended VGA configuration and Hyper M.2 configuration. Slot Description 1 PCIEX16(G5) 5 PCIEX16(G4) Single VGA x16 - Chapter 1 Recommended VGA configuration Dual VGA x16 x4 Connect chassis fans to the chassis fan connectors when using multiple graphics cards for better thermal environment. PCIe bifurcation & M.2 settings in PCIe x16 slots (from CPU) Slot Description 1 PCIEX16(G5) Quantity of identifiable M.
Using the PCIe Slot Q-Release The PCIEX16(G5) slot comes with a PCIe Slot Q-Release button allowing you to easily remove an expansion card installed to this PCIe slot, even when the expansion card may be blocking the PCIe push-latch, such as a graphics card. Chapter 1 To release an expansion card using the PCIe Slot Q-Release: Press the PCIe Slot Q-Release button with one hand whilst slightly lifting the expansion card with the other hand.
4. Fan and Pump headers The Fan and Pump headers allow you to connect fans or pumps to cool the system. CPU_FAN Chapter 1 CPU_OPT CHA_FAN1 CHA_FAN2 CHA_FAN3 CHA_FAN4 AIO_PUMP • DO NOT forget to connect the fan cables to the fan headers. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan headers! • Ensure the cable is fully inserted into the header.
5. Power connectors These Power connectors allow you to connect your motherboard to a power supply. The power supply plugs are designed to fit in only one orientation. Find the proper orientation and push down firmly until the power supply plugs are fully inserted. Chapter 1 CPU_12V_1 ATX_PWR CPU_12V_2 Ensure to connect all the 8-pin power plugs. 1-10 • We recommend that you use a PSU with a higher power output when configuring a system with more power-consuming devices.
6. M.2 slots The M.2 slots allow you to install M.2 devices such as M.2 SSD modules. M.2_1 Chapter 1 M.2_2 M.2_3 M.2_4 • Intel® Core™ Processors (14th & 13th & 12th Gen): - M.2_1 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0 x4 mode) • Intel® Z790 Chipset: - M.2_2 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode) - M.2_3 slot (Key M), type 2242/2260/2280/22110 (supports PCIe 4.0 x4 mode) - M.2_4 slot (Key M), type 2242/2260/2280 (supports PCIe 4.
7. SATA 6Gb/s ports The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and hard disk drives via a SATA cable. Chapter 1 SATA6G_1 SATA6G_2 SATA6G_3 SATA6G_4 If you installed SATA storage devices, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology through the onboard Intel® Z790 chipset. Before creating a RAID set, refer to the RAID Configuration Guide. You can download the RAID Configuration Guide from the ASUS website.
8. USB 20Gbps Type-C® Front Panel connector Chapter 1 The USB 20Gbps Type-C® connector allows you to connect a USB 20Gbps Type-C® module for additional USB 20Gbps ports on the front panel. The USB 20Gbps Type-C® connector provides data transfer speeds of up to 20 Gb/s and PD 3.0 support for up to 30W fast charging technology. U20G_C5 The USB 20Gbps Type-C® module is purchased separately. 9. USB 5Gbps header The USB 5Gbps header allows you to connect a USB 5Gbps module for additional USB 5Gbps ports.
10. USB 2.0 headers The USB 2.0 headers allow you to connect USB modules for additional USB 2.0 ports. The USB 2.0 headers provide data transfer speeds of up to 480 Mb/s. Chapter 1 USB_1011 USB_1213 DO NOT connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB 2.0 module is purchased separately.
11. Addressable Gen2 headers The Addressable Gen2 headers allow you to connect individually addressable RGB WS2812B LED strips or WS2812B based LED strips. Chapter 1 ADD GEN2_1 ADD GEN2_2 ADD GEN2_3 Before you install or remove any component, ensure that the power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.
12. Aura RGB header The Aura RGB header allows you to connect RGB LED strips. RGB_HEADER Chapter 1 Before you install or remove any component, ensure that the power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. 1-16 • The Aura RGB header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum power rating of 3A (12V). • Actual lighting and color will vary with LED strip.
13. Clear CMOS header Chapter 1 The Clear CMOS header allows you to clear the Real Time Clock (RTC) RAM in the CMOS, which contains the date, time, system passwords, and system setup parameters. CLRTC To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds. 3. Plug the power cord and turn ON the computer. 4. Hold down the key during the boot process and enter BIOS setup to re-enter data.
14. COM Port header The COM (Serial) Port header allows you to connect a COM port module. Connect the COM port module cable to this header, then install the module to a slot opening on the system chassis. Chapter 1 COM The COM port module is purchased separately.
15. Front Panel Audio header Chapter 1 The Front Panel Audio header is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this header. F_AUDIO We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
16. System Panel header The System Panel header supports several chassis-mounted functions. Chapter 1 PANEL • System Power LED header (PLED) The 2-pin and/or 3-1 pin headers allow you to connect the System Power LED. The System Power LED lights up when the system is connected to a power source, or when you turn on the system power, and blinks when the system is in sleep mode. • Storage Device Activity LED header (HDD_LED) The 2-pin header allows you to connect the Storage Device Activity LED.
17. Thunderbolt™ (USB4®) header Chapter 1 The Thunderbolt™ (USB4®) header allows you to connect an add-on Thunderbolt™ I/O card that supports Intel®’s Thunderbolt™ Technology, allowing you to connect Thunderbolt™-enabled devices to form a daisy-chain configuration. TB_HEADER Please visit the official website of your purchased Thunderbolt™ card for more details on compatibility. The Thunderbolt™ card can only be used when installed to the PCIEX16(G4) slot.
18. Q-LEDs The Q-LEDs check key components (CPU, DRAM, VGA, and booting devices) during the motherboard booting process. If an error is found, the critical component’s LED stays lit up until the problem is solved. Chapter 1 CPU (RED) DRAM (YELLOW) VGA (WHITE) BOOT (YELLOW GREEN) 1-22 • The Q-LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case.
1.3 Motherboard rear and audio connections 1.3.1 Rear I/O connection 4 2 5 3 6 Chapter 1 1 7 8 9 10 Rear panel connectors 1. 2. 3. 4. 5. 6. 7. 8. DisplayPort USB 5Gbps (Blue) Type-A ports E1, E2, E3, and E4 Intel® 2.5Gb Ethernet port* HDMI™ port USB 10Gbps Type-C® port C9 USB 10Gbps (Teal blue) Type-A ports 3 and 4 USB 20Gbps Type-C® port C1 Wi-Fi module 9. Optical S/PDIF OUT port 10.
* Intel® 2.5Gb Ethernet port LED indications Chapter 1 Activity Link LED Speed LED Status Description Status Description OFF No link OFF GREEN Linked OFF BLINKING Data activity No link 100 Mbps / 10 Mbps connection 2.5 Gbps connection 1 Gbps connection GREEN ORANGE ACT/LINK LED SPEED LED LAN port ** Audio 2, 4, 5.1 or 7.1-channel configuration 1-24 Port 2-channel 4-channel 5.1-channel 7.
1.3.
Connect to 5.1-channel Speakers Chapter 1 Connect to 7.
Chapter 2: Basic Setup 2 Basic Setup The installation diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. CPU installation • Ensure that you install the correct CPU designed for LGA1700 socket only. DO NOT install a CPU designed for LGA1155, LGA1156, LGA1151, and LGA1200 sockets on the LGA1700 socket. • The CPU fits in only one correct orientation.
Chapter 2 Ensure to remove the CPU Socket lever protector on the lever latch before locking the lever latch under the retention tab. Failure to do so may cause damages to your system when installing the cooling system.
DIMM installation Chapter 2 2.
2.3 M.2 installation The illustrations only show the installation steps for a 22110 M.2 slot, the steps are the same for the other M.2 slots. • Use a Phillips screwdriver when removing or installing the screws or screw stands mentioned in this section. • If the thermal pad on the M.2 heatsink becomes damaged, we recommend replacing it with the bundled thermal pad or a thermal pad with a thickness of 1.25mm. • Supported M.2 type varies per motherboard. 1. Loosen the screws from the M.2 heatsinks.
3. (optional) If required, remove the pre-installed removable M.2 Q-Latch screw at the 2280 length screw hole. Only follow this step if a removable M.2 Q-Latch screw is pre-installed at the 2280 length screw hole and can be removed. Chapter 2 4. (optional) Install the bundled rubber for M.2 if you are installing a single sided M.2 module. DO NOT install the bundled rubber for M.2 when installing a double-sided M.2 module. The rubber installed by default is compatible with double sided M.2 modules.
5. (optional) Install the M.2 Q-Latch to the M.2 length screw hole you wish to install your M.2 module to. You can use a bundled M.2 Q-Latch screw or a pre-installed removable M.2 Q-Latch screw. 6. Rotate and adjust the M.2 Q-Latch so that the handle points away from the M.2 slot. 7. Install your M.2 module to the M.2 slot. Chapter 2 Ensure that there is nothing obstructing your M.2 module when installing the M.2 module to the M.2 slot. 8. Rotate the M.2 Q-Latch clockwise to secure the M.
Replace the heatsinks. 11. Secure the heatsinks using the screws on the heatsinks. Chapter 2 10.
2.4 1. Motherboard installation (on selected models) Install the bundled I/O Shield to the chassis rear I/O panel. Only install the I/O Shield if your motherboard does not have a pre-installed I/O shield. Chapter 2 2. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel. 3. Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis.
2.5 Expansion card installation 2.5.1 Thunderbolt™ series card installation 6-pin PCIe power connector USB Type-C® port connects to Thunderbolt devices Chapter 2 MiniDP in port connects to DP out port on the motherboard or a VGA card USB 2.0 header Thunderbolt™ header The Thunderbolt™ card can only be used when installed to the PCIEX16(G4) slot. Ensure to install your Thunderbolt™ card to the PCIEX16(G4) slot.
2.6 ASUS WiFi Q-Antenna installation (on selected models) Installing the ASUS WiFi Q-Antenna Connect the bundled ASUS WiFi Q-Antenna connector to the Wi-Fi ports at the back of the chassis. Chapter 2 • Ensure to hold tightly onto the connector when removing the antenna connector from the Wi-Fi ports, and refrain from attempting to remove the antenna connector from the Wi-Fi ports by pulling on the antenna connector cable. • The antenna can only be extended to a right angle (90°).
2.7 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Ensure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: Monitor b. External storage devices (starting with the last device on the chain) c.
Chapter 2 2-12 Chapter 2: Basic Installation
Chapter 3: BIOS and RAID Support BIOS and RAID Support 3 For more details on BIOS and RAID configurations, please refer to Manual & Document under the Support tab of the product information site, or visit https://www.asus.com/support. 3.1 Knowing UEFI BIOS BIOS (Basic Input and Output System) stores system hardware settings such as storage device configuration, overclocking settings, advanced power management, and boot device configuration that are needed for system startup in the motherboard CMOS.
3.2 ASUS EZ Flash 3 The ASUS EZ Flash 3 feature allows you to update the BIOS without using an OS‑based utility. Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu or press the hotkey. To update the BIOS: • This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only.
3.3 ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using a USB flash drive that contains the BIOS file. Recovering the BIOS 1. Download the latest BIOS version for this motherboard from https://www.asus.com/support/. 2. Rename the file using one of the following methods: Launch the BIOSRenamer.
3.4 RAID configurations The motherboard supports RAID configurations. RAID definitions RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. Use of two new identical hard disk drives is required for this setup.
Appendix Appendix General Notices FCC Compliance Information Responsible Party: Asus Computer International Address: 48720 Kato Rd., Fremont, CA 94538, USA Phone / Fax No: (510)739-3777 / (510)608-4555 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
VCCI: Japan Compliance Statement Class B ITE Japan JATE 本製品は電気通信事業者（移動通信会社、固定通信会社、インターネットプロバイダ等）の通信 回線（公衆無線LANを含む）に直接接続することができません。本製品をインターネットに接続す る場合は、必ずルーター等を経由し接続してください。 Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations.
Türkiye RoHS AEEE Yönetmeliğine Uygundur ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions. DO NOT throw the motherboard in municipal waste.
Notices for Wi-Fi model FCC RF Caution Statement WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC Wi-Fi 6E Caution Statement Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.
KC: Korea Warning Statement NCC: Wireless Statement 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不 得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器 材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信 管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工 業、科學及醫療用電波輻射性電機設備之干擾。 應避免影響附近雷達系統之操作。 Japan RF Equipment Statement 屋外での使用について 電波法の定めにより5.2GHz、5.
Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
Motherboard User Manual Упрощенное заявление о соответствии европейской директиве ASUSTek Computer Inc. заявляет, что устройство соответствует основным требованиям и другим соответствующим условиям директивы 2014/53/EU. Полный текст декларации соответствия ЕС доступен на https://www.asus.com/support/. Работа WiFi в диапазоне частот 5150-5350 должна быть ограничена использованием в помещениях для стран, перечисленных в таблице ниже: a.
Appendix Pojednostavljena EU Izjava o sukladnosti ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan s bitnim zahtjevima i ostalim odgovarajućim odredbama direktive 2014/53/EU. Cijeli tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/. WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit će ograničen na upotrebu u zatvorenom prostoru u zemljama na donjem popisu: a.
:)LPI( לבית בהספק נמוךWi-Fi 6E מכשיריa. עד5945 המכשיר מוגבל לשימוש פנימי בלבד בשימוש בטווח התדרים 6425MHz ( בבלגיהBE), ( בולגריהBG), ( קפריסיןCY), ( צ'כיהCZ), אסטוניה (EE), ( צרפתFR), ( איסלנדIS), ( אירלנדIE), ( ליטאLT), ( גרמניהDE), הולנד (NL), ( ספרדES). :)) (מכשירים ניידיםVLP( בהספק נמוך מאודWi-Fi 6E מכשיריb.
Appendix Declarație de conformitate UE, versiune simplificată Prin prezenta, ASUSTek Computer Inc. declară că acest dispozitiv este în conformitate cu reglementările esențiale și cu celelalte prevederi relevante ale Directivei 2014/53/UE. Textul complet al declarației de conformitate UE este disponibil la adresa https://www.asus.com/support/. Pentru ţările listate în tabelul de mai jos, reţelele WiFi care funcţionează în banda de frecvenţă de 5.150-5.350 MHz trebuie utilizate doar în interior: a.
Спрощена декларація про відповідність нормам ЄС ASUSTek Computer Inc. заявляє, що цей пристрій відповідає основним вимогам та іншим відповідним вимогам Директиви 2014 / 53 / EU. Повний текст декларації відповідності нормам ЄС доступний на https://www.asus.com/support/. Робота Wi-Fi на частоті 5150-5350 МГц обмежується використанням у приміщенні для країн, поданих у таблиці нижче: a. b.
Warranty EN: ASUS Guarantee Information • ASUS offers a voluntary manufacturer’s Commercial Guarantee. • ASUS reserves the right to interpret the provisions of the ASUS Commercial Guarantee. • This ASUS Commercial Guarantee is provided independently and in addition to the statutory Legal Guarantee and in no way affects or limits the rights under the Legal Guarantee. CR: Informacije o ASUS jamstvu • ASUS dragovoljno nudi komercijalno proizvođačko jamstvo.
Motherboard User Manual SW: ASUS garantiinformation • ASUS erbjuder en frivillig kommersiell tillverkningsgaranti. • ASUS förbehåller sig rätten att tolka bestämmelserna i ASUS kommersiella garanti. • Denna kommersiella garanti från ASUS tillhandahålles separat och som tillägg till den lagstadgade garantin, och påverkar eller begränsar på intet sätts rättigheterna under den lagstadgade garantin. För all garantiinformation, besök https://www.asus.com/se/support/.
ASUS contact information ASUSTeK COMPUTER INC. Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112 ASUS COMPUTER INTERNATIONAL (America) Address: 48720 Kato Rd., Fremont, CA 94538, USA ASUS COMPUTER GmbH (Germany and Austria) Address: Harkortstrasse 21-23, 40880 Ratingen, Germany ASUSTeK (UK) LIMITED Address: 1st Floor, Sackville House, 143-149 Fenchurch Street, London, EC3M 6BL, England, United Kingdom Service and Support Visit our multi-language website at https://www.asus.com/support.
