BIOS 使用手冊 Motherboard PRIME / ProArt / TUF GAMING Intel 700 系列
T21967 第三版 2023 年 4 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 1. 2. 認識 BIOS 程式................................................................................................................ 4 BIOS 程式設定.................................................................................................................. 5 2.1 EZ Mode ........................................................................................................ 6 2.2 進階選單(Advanced menu)................................................................. 7 2.3 Qfan Control....................
BIOS 程式設定 1.
2.
2.
2.
功能表列 BIOS 設定程式最上方各選單功能說明如下: My Favorites 本項目將記錄時常使用的系統設定及設定值。 Main 本項目提供系統基本設定。 Ai Tweaker 本項目提供超頻設定。 Advanced 本項目提供系統進階功能設定。 Monitor 本項目提供溫度、電源及風扇功能設定。 Boot 本項目提供開機磁碟設定。 Tool 本項目提供特殊功能設定。 Exit 本項目提供離開 BIOS 設定程式與出廠預設值還原功能。 選單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯示 Main 選單的項目。 點選選單中的其他項目(例如:My Favories、Ai Tweaker、Advanced、Monitor、Boot、Tool 與 Exit)也會出現該項目不同的選項。 子選單 在選單畫面中,若功能選項前面有一個小三角形標記(>),代表此為子選單,您可 利用方向鍵來選擇,並按下 鍵來進入子選單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程式介面顯示的語言。點選這個按鈕 來選擇您想要的 BIOS
AI OC Guide 這個按鈕位在功能表列的上方,用來檢視超頻的敘述並且可以啟動該功能。您也可 以透過按下 鍵以使用此項目。 • 請參考 AI OC Guide 一節以獲得更多資訊。 • 這項功能只有在安裝沒有鎖頻的處理器時才能使用。 • 這項功能僅適用於特定型號。 搜尋(F9) 這個按鈕用來透過輸入名稱搜尋 BIOS 項目,輸入名稱可以找到相關的項目列表。您 可以按下 鍵開啟此選單。 AURA 這個按鈕用來啟動或關閉 Aura 特效或功能性 LED 指示燈。您可以按下 鍵開啟 此選單。 [All On] 啟動所有的 LED 指示燈(Aura 特效或是功能性指示燈)。 [Stealth Mode] 關閉所有的 LED 指示燈(Aura 特效與功能性指示燈)。 [Aura Only] 啟動 Aura 特效,而功能性指示燈將會關閉。 [Aura Off] 關閉 Aura 特效,而功能性指示燈依舊為開啟狀態。 ReSize BAR 這個按鈕用來啟動或關閉 ReSize BAR 功能。 [On] 啟動 ReSize BAR 支援以充分利用 GPU 記憶體。
項目說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動變更。使用 按鍵來抓取 BIOS 螢幕畫面,並儲存至攜帶式儲存裝置。 設定視窗 此區域顯示選單項目的設定值。這些項目中,有的功能選項僅為告知使用者目前執 行狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方 向鍵移動項目時, 設定值被選擇後以反白顯示。要改變設定值請選擇此項目,並按下 鍵以顯示 設定值列表。 上次修改的設定按鈕 按下此按鈕可檢視您在 BIOS 設定中上一次所做的修改項目。 10 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 使用手冊
2.
手動設定風扇 從設定檔清單中選擇 Manual 來手動設定風扇運作的速度。 速度點 點選或輕觸以手動設定風扇 請依照以下步驟設定風扇: 12 1. 選擇想要設定的風扇並查看該風扇現在的狀況。 2. 點選並拖曳速度點來調整風扇的運作速度。 3.
2.
3.
新增項目至我的最愛 請依照以下步驟新增項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程式畫面中點選 MyFavorite 來啟動設定樹狀圖 畫面。 2. 在設定樹狀圖畫面中選擇想要儲存至我的最愛的 BIOS 項目。 主選單面板 選擇快捷方式項目 子選單面板 刪除所有我 的最愛項目 回復預設值 3. 從主選單面板選擇項目,然後點選子選單中想要儲存至我的最愛的選項,再點 選或輕觸 或是按下 按鍵。 以下項目無法加入至我的最愛: • 有子選單的項目。 • 使用者自訂項目,例如:語言、開機裝置順序。。 • 設定項目,例如:記憶體 SPD 資訊、系統時間與日期。 4. 點選 Exit (ESC) 或按下 鍵來關閉樹狀圖視窗。 5.
4.
• 若您忘記設定的 BIOS 密碼,可以採用清除 CMOS 即時鐘(RTC)記憶體。請 參考主機板使用手冊中的相關說明以了解 Clear CMOS 按鈕並清除 CMOS 即 時時鐘(RTC)記憶體資料。 • Administrator 或 User Password 項目預設值為 [Not Installed]。當您設定密碼 之後將顯示為 [Installed]。 Administrator Password(設定系統管理員密碼) 當您設定系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設定程式中的某些 資訊無法檢視或變更設定。 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼並選擇 OK。 請依照以下步驟變更系統管理員密碼(Administrator Password): 1.
5.
以下項目只有在 Ai Overclock Tuner 設定為 [Manual]、 [AEMP]、 [XMP I] 或 [XMP II] 時才會出現。 BCLK Frequency 本項目用來設定 BCLK 頻率以增強系統效能。請使用 <+> 與 <-> 鍵調整數值。 建議您依照處理器規格設定數值,設定過高的數值可能造成處理器永久性的損害。 以下項目只有在 Ai Overclock Tuner 設定為 [AEMP] 時才會出現。 AEMP 本項目可以用來選擇 ASUS Enhanced Memory Profile(AEMP)。每個設定檔都有專 屬動態隨機存取記憶體(DRAM)頻率、時間與電壓。 以下項目只有在 Ai Overclock Tuner 設定為 [XMP I] 或 [XMP II] 時才會出現。 XMP 本項目用來選擇 Extreme Memory Profile。每個設定檔都有專屬動態隨機存取記憶體 (DRAM)頻率、時間與電壓。 Intel(R) Adaptive Boost Technology 本項目用來開啟或關閉 IABT 以透過允許更高的多核心頻率來提高效能。當存在電 流、功率
BCLK FrequencyDRAM Frequency Ratio [Auto] 自動最佳化 BCLK 頻率與 DRAM 頻率。 [100:133] 本項目將 BCLK 頻率與 DRAM 頻率的比值設為 100:133。 [100:100] 本項目將 BCLK 頻率與 DRAM 頻率的比值設為 100:100。 Memory Controller : DRAM Frequency Ratio BCLK Frequency: DRAM Frequency Ratio 選擇 100:133 時有較好的超頻性能,同時 1:2 Memory Controller: DRAM Frequency Ratio 僅在 DRAM 比值為偶數時運作。 設定值有:[Auto] [1:1] [1:2] [1:4] DRAM Frequency 本項目可設定記憶體的運作頻率。設定選項會隨著 BCLK Frequency 設定值變動。選 擇自動模式以套用最佳化設定。 以下項目中的設定值,可能會隨安裝在主機板上的 CPU 與記憶體模組而異。 呈灰色的設定值不建議使用,請使用呈白色的設定值。 OC Tuner OC T
以下項目只有當 Performance Core Ratio 設為 [By Core Usage] 時才會出現。 1-Core Ratio Limit / 2-Core Ratio Limit / 3-Core Ratio Limit / 4-Core Ratio Limit / 5-Core Ratio Limit / 6-Core Ratio Limit N-core 比率限制需高於或等於(N+1)-core 比率限制。(N 代表 CPU 核心數量)當 核心數量低於 N 時,核心比率限制無法設定為 [Auto] 。最大核心比率限制需低於或 等於第二大核心比率限制。請使用 <+> 與 <-> 鍵調整數值。 設定值有:[Auto] [36] - [85] 以下項目只有當 Performance Core Ratio 設為 [AI Optimized] 時才會出現。 Optimized AVX Frequency 標準用例選擇 [Normal Use],或是極端負載如 Prime 95 AVX 時選擇[Heavy AVX]。 設定值有:[Normal Use] [Heavy AVX] 以下項目只有當 Per
以下項目只有在 Performance Core0-5 specific Voltage 設為 [Adaptive Mode] 時 才會出現。 Offset Mode Sign [+] 設定正數值偏移電壓。 [-] 設定負數值偏移電壓。 Additional Turbo Mode CPU Core0-5 Voltage 設定在 Turbo 模式下運作時饋送到 CPU 核心的電壓量。設定高 CPU 核心頻率 時增加電壓。該電壓會受到偏移值的影響。請使用 <+> 與 <-> 鍵調整數值。數 值以 0.001V 為間隔,變更的範圍由 0.001V 至 1.920V。 設定值有:[Auto] [0.00100] - [1.92000] Performance Core0-5 Offset 設定 CPU 核心電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為 間隔,變更的範圍由 0.001 V 至 0.999 V。[Auto] [0.00100] - [0.
以下項目只有當 Efficient Core Ratio 設為 [Auto]、[Sync All Cores] 或 [By Core Usage] 時才會出現。 Specific Efficient Core Efficient Core Group0-1 Specific Ratio Limit 為部分效能核心設定比率限制。請使用 <+> 與 <-> 鍵調整數值。 設定值有:[Auto] [8] - [120] Efficient Core Group0-1 specific Voltage 本項目用來設定 CPU 核心的電壓供應。設為 [Auto] 將依據使用的 CPU 核心比 調節電壓。不要將此設定與 VCCIN(CPU 輸入電壓)混淆。 設定值有:[Auto] [Manual Mode] [Adaptive Mode] 以下項目只有在 Efficient Core Group0-1 specific Voltage 設為 [Manual Mode] 時 才會出現。 CPU Core-0 Voltage Override / CPU Core-1 Voltage Override 設定 CPU 核心
AVX Related Controls AVX2 啟用或關閉 AVX 2 控制器。 設定值有:[Auto] [Disabled] [Enabled] AVX2 Ratio Offset to per-core Ratio Limit 設定值有: [Auto] [User Specify] 以下項目只有在 AVX2 Ratio Offset to per-core Ratio Limit 設為 [User Specify] 時 才會出現。 AVX2 Ratio Offset 指定降低 AVX 比與每個核心比的 bin 數量。AVX 是一個壓力更大的工作負 載,降低 AVX 比率有助於確保 SSE 工作負載的最大可能比。使用 Mailbox MSR 0x150、cmd 0x1B。範圍 0-31。0=無偏移。請使用 <+> 與 <-> 鍵調整數 值。 設定值有:[0] - [31] AVX2 Voltage Guardband Scale Factor 設定值有:[Auto] [User Specify] 以下項目只有在 AVX2 Voltage Guardband Scale Factor 設為 [User
DRAM RAS# ACT Time 設定值有:[Auto] [1] - [511] DRAM Command Rate 設定值有:[Auto] [1N] [2N] [3N] [N:1] 以下項目只有當 DRAM Command Rate 設為 [N:1] 時才會出現。 N to 1 ratio 每個有效命令周期之間的數值。 設定值有:[1] - [7] Secondary Timings DRAM RAS# to RAS# Delay L 設定值有:[Auto] [1] - [63] DRAM RAS# to RAS# Delay S 設定值有:[Auto] [1] - [127] DRAM REF Cycle Time 設定值有:[Auto] [1] - [65535] DRAM REF Cycle Time 2 設定值有:[Auto] [1] - [65535] DRAM REF Cycle Time Same Bank 設定值有:[Auto] [0] - [2047] DRAM Refresh Interval 設定值有:[Auto] [1] - [262143] DRAM WRITE Recove
Skew Control DDRCRCOMPCTL0/1/2 Ctl0 dqvrefup 設定值有:[Auto] [0] - [255] Ctl0 dqvrefdn 設定值有:[Auto] [0] - [255] Ctl0 dqodtvrefup 設定值有:[Auto] [0] - [255] Ctl0 dqodtvrefdn 設定值有:[Auto] [0] - [255] Ctl1 cmdvrefup 設定值有:[Auto] [0] - [255] Ctl1 ctlvrefup 設定值有:[Auto] [0] - [255] Ctl1 clkvrefup 設定值有:[Auto] [0] - [255] Ctl1 ckecsvrefup 設定值有:[Auto] [0] - [255] Ctl2 cmdvrefdn 設定值有:[Auto] [0] - [255] Ctl2 ctlvrefdn 設定值有:[Auto] [0] - [255] Ctl2 clkvrefdn 設定值有:[Auto] [0] - [255] Tc Odt Control ODT_READ_DURATION 設定值有:[Auto] [0]
DQ RTT PARK 設定值有:[Auto] [0 DRAM Clock] [34 DRAM Clock] [40 DRAM Clock] [48 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 DRAM Clock] DQ RTT PARK DQS 設定值有:[Auto] [0 DRAM Clock] [34 DRAM Clock] [40 DRAM Clock] [48 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 DRAM Clock] GroupA CA ODT 設定值有: [Auto] [0 DRAM Clock] [40 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 xDRAM Clock] [480 DRAM Clock] GroupA CS ODT 設定值有: [Auto] [0 DRAM Clock] [40 DRAM Clock] [6
Memory Training Algorithms 本選單的項目用來讓您開啟或關閉不同的記憶體訓練演算法。 Early Command Training 設定值有:[Auto] [Enabled] [Disabled] SenseAmp Offset Training 設定值有:[Auto] [Enabled] [Disabled] Early ReadMPR Timing Centering 2D 設定值有:[Auto] [Enabled] [Disabled] Read MPR Training 設定值有:[Auto] [Enabled] [Disabled] Receive Enable Training 設定值有:[Auto] [Enabled] [Disabled] Jedec Write Leveling 設定值有:[Auto] [Enabled] [Disabled] Early Write Timing Centering 2D 設定值有:[Auto] [Disabled] [Enabled] Early Read Timing Centering 2D 設定值有:[Auto] [Disab
Command Voltage Centering 設定值有:[Auto] [Disabled] [Enabled] Early Command Voltage Centering 設定值有:[Auto] [Disabled] [Enabled] Write Voltage Centering 2D 設定值有:[Auto] [Disabled] [Enabled] Read Voltage Centering 2D 設定值有:[Auto] [Disabled] [Enabled] Late Command Training 設定值有:[Disabled] [Enabled] [Auto] Round Trip Latency 設定值有:[Auto] [Disabled] [Enabled] Turn Around Timing Training 設定值有:[Auto] [Disabled] [Enabled] CMD CTL CLK Slew Rate 設定值有:[Auto] [Disabled] [Enabled] CMD/CTL DS & E 2D 設定值有:[Auto] [Disabled] [Enab
EARLY DIMM DFE Training 設定值有:[Auto] [Disabled] [Enabled] Tx Dqs Dcc Training 設定值有:[Auto] [Disabled] [Enabled] DRAM DCA Training 設定值有:[Auto] [Disabled] [Enabled] Write Driver Strength Training 設定值有:[Auto] [Disabled] [Enabled] Rank Margin Tool 設定值有:[Auto] [Disabled] [Enabled] Memory Test 設定值有:[Auto] [Disabled] [Enabled] DIMM SPD Alias Test 設定值有:[Auto] [Disabled] [Enabled] Receive Enable Centering 1D 設定值有:[Auto] [Disabled] [Enabled] Retrain Margin Check 設定值有:[Auto] [Disabled] [Enabled] Write Drive Strength Up/
tWRWR_sg 設定值有:[Auto] [0] - [127] tWRWR_dg 設定值有:[Auto] [0] - [127] tWRRD_sg 設定值有:[Auto] [0] - [511] tWRRD_dg 設定值有:[Auto] [0] - [511] tRDRD_dr 設定值有:[Auto] [0] - [255] tRDRD_dd 設定值有:[Auto] [0] - [255] tRDWR_dr 設定值有:[Auto] [0] - [255] tRDWR_dd 設定值有:[Auto] [0] - [255] tWRWR_dr 設定值有:[Auto] [0] - [127] tWRWR_dd 設定值有:[Auto] [0] - [255] tWRRD_dr 設定值有:[Auto] [0] - [127] tWRRD_dd 設定值有:[Auto] [0] - [127] tRPRE 設定值有:[Auto] [0] - [4] tWPRE 設定值有:[Auto] [0] - [4] tWRPRE 設定值有:[Auto] [0] - [1023] tPRPDEN 設定值有:[Auto] [0] - [3
tREFIX9 設定值有:[Auto] [0] - [255] Ref Interval 設定值有:[Auto] [0] - [8191] tXPDLL 設定值有:[Auto] [0] - [127] tXP 設定值有:[Auto] [0] - [127] tPPD 設定值有:[Auto] [0] - [15] tCCD_L_tDLLK 設定值有:[Auto] [0] - [15] Misc.
Controller 0, Channel 1 Control 本項目用來開啟或關閉 Controller 0 與 Channel 1。 設定值有:[Enabled] [Disabled] Controller 1, Channel 0 Control 本項目用來開啟或關閉 Controller 1 與 Channel 0。 設定值有:[Enabled] [Disabled] Controller 1, Channel 1 Control 本項目用來開啟或關閉 Controller 1 與 Channel 1。 設定值有:[Enabled] [Disabled] MC_Vref0-2 設定值有:[Auto] [0] - [65533] Fine Granularity Refresh mode 設定值有:[Auto] [Disabled] [Enabled] DRAM SPD Configuration SDRAM Density Per Die 設定值有: [Auto] [4 Gb] [8 Gb] [12 Gb] [16 Gb] [24 Gb] [32 Gb] [48 Gb] [64 Gb] SDRAM B
以下項目只有在 SA GV 設定為 [Enabled]、[Fixed to 1st Point]、[Fixed to 2nd Point]、[Fixed to 3rd Point] 或 [Fixed to 4th Point] 時才會出現。 First Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。 設定值有:[0] - [65535] First Point Gear 本項目可以設定 SAGV 點的齒輪比。0-Auto、1-G1、2-G2 與 4-G4 。設定值有:[0] - [4] Second Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。設定值有:[0] - [65535] Second Point Gear 本項目可以設定 SAGV 點的齒輪比。0-Auto、1-G1、2-G2 與 4-G4 。設定值有:[0] - [4] Third Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。設定值有:[0]
CPU Current Capability 本項目用來設定較高的數值提供更大的總電力範圍,同時擴展超頻頻率的範 圍。當系統超頻,或是 CPU 在較高負載需要獲得額外的電力支援時,請選擇 較高的數值。 設定值有:[Auto] [100%] - [140%] 當 CPU 超頻或是需負載額外的電力時,請設置較高的數值。 CPU VRM Switching Frequency 本項目用來設定 VRM 開關頻率。VRM 開關頻率影響瞬態回應與 VRM 元件溫 度。選擇 [Manual] 設定較高的頻率可以獲得較快的暫態響應速度。當處理器 運作於高電壓與高負載線校準值時,建議使用 VRM 散熱器主動冷卻。 設定值有:[Auto] [Manual] 請勿將散熱系統移除,散熱環境需受到監控。 以下項目只有在 CPU VRM Switching Frequency 設定為 [Manual] 時才會出現。 Fixed CPU VRM Switching Frequency(KHz) 本項目可讓您設定固定的 VRM 頻率。數值以 50kHz 為間隔,變更的範圍由 250kHz 至 500kHz。 CPU Power Dut
CPU VRM Thermal Control 關閉本項目可提高 CPU VRM 的溫度限制。 設定值有:[Auto] [Enabled] [Disabled] 請勿將散熱系統移除。 以下項目只有使用內建顯示卡時才會出現。 CPU Graphics Load-line Calibration Load-line 是根據 Intel 所訂立之 VRM 規格,其設定值將影響繪圖處理器電 壓。CPU 顯示卡運作電壓將依 CPU 顯示卡的負載呈比例性遞減。繪圖處理 器運行電壓將依繪圖處理器的負載呈比例性遞減。從 Level 1 至 Level 8 中選 擇,以將處理器圖形電源電壓從 100% 調整至 0%。 設定值有:[Auto] [Level 1] [Level 2] [Level 3] [Level 4:Recommended for OC] [Level 5] [Level 6] [Level 7] 實際提升的效能將視 CPU 顯示卡規格而異。請勿將散熱系統移除。 CPU Graphics Current Capability 本項目用來設定繪圖處理器的電力相式控制功能。較高的值可提供更寬的總功 率範圍,
Internal CPU Power Management 本項目用來管理與設定 CPU 電力。 Maximum CPU Core Temperature 設定 CPU 核心的最高允許溫度。當達到此溫度時,CPU 將會節流或關閉以防 止核心損壞。 設定值有:[Auto] [62] - [115] 請勿將數值設定太高,否則高溫可能會造成 CPU 永久損壞。 Turbo Mode Parameters IVR Transmitter VDDQ ICCMAX 設定值有:[Auto] [0] - [15] Unlimited ICCMAX 本項目用來開啟或關閉無限制 ICCMAX。支援 VR 電流限制(ICCMAX)值設 定至 511.75A 以上。 [Auto] [Disabled] [Enabled]] CPU Core/Cache Current Limit Max. 本項目可讓您設定更高的電流限制以防止超頻時的頻率或功率節流。可以設定 為最大值(511.75)以防止超頻時節流。 設定值有:[Auto] [0.00] - [511.
Dual Tau Boost 本項目可讓您開啟 Dual Tau Boost 功能。僅適用於桌機 35W/65W/12W sku。 啟用 DPTF 後,此功能將被忽略。 設定值有:[Disabled] [Enabled] IA AC Load Line 本項目用來設定 AC 負載線,以毫歐姆為單位。請使用 <+> 與 <-> 鍵調整數 值。 設定值有:[Auto] [0.01] - [62.49] IA DC Load Line 本項目用來設定 DC 負載線,以毫歐姆為單位。請使用 <+> 與 <-> 鍵調整數 值。 設定值有:[Auto] [0.01] - [62.
Enhanced TVB 本項目僅支援特定規格。 設定值有:[Auto] [Disabled] [Enabled] Overclocking TVB 開啟本項目可繪製溫度/頻率依賴性。 設定值有: [Auto] [Disabled] [Enabled] [+1Boost Profile] [+2Boost Profile] +1Boost Profile(K CPU): 此設定將在自動最佳化溫度控制的幫助下,增加一個 bin 的功率。 +2Boost Profile(K CPU): 此設定將在自動最佳化溫度控制的幫助下,增加兩個 bin 的功率。 以下的項目只有在 Overclocking TVB 設為 [Enabled] 時才會出現。 1-Core Active / 2-Core Active / 3-Core Active / 4-Core Active / 5-Core Active / 6-Core Active 設定值有:[Auto] [Enabled] 以下的項目只有在 1-Core Active、 2-Core Active、 3-Core Active、 4-Core Active、 5-
以下項目只有在 Negative Ratio Offset B 設為 [User Specify] 時才會出現。 Ratio Offset 請使用 <+> 與 <-> 鍵調整數值。 設定值有:[0] - [31] V/F Point Offset Offset Mode Sign 1-11 設定值有: [+] [-] V/F Point 1-11 Offset 設定值有:[Auto] [0.001] - [0.
UnderVolt Protection 啟用本項目時,在作業系統執行期使用者將無法指定低電壓。建議維持啟用的 預設值。 [Disabled] 無低電壓保護。 [Enabled] 允許 BIOS 設定低電壓,但執行期啟用低電壓保護。 Core PLL Voltage 本項目可以用來設定 Core PLL VCC Trim。數值以 0.015V 為間隔,變更的範 圍由 0.900V 至 1.845V。 設定值有:[Auto] [0.90000] - [1.84500] GT PLL Voltage 本項目可以用來設定 GT PLL VCC Trim。數值以 0.015V 為間隔,變更的範圍 由 0.900V 至 1.845V。 設定值有:[Auto] [0.90000] - [1.84500] Ring PLL Voltage 本項目可以用來設定 Ring PLL VCC Trim。數值以 0.015V 為間隔,變更的範圍 由 0.900V 至 1.845V。 設定值有:[Auto] [0.90000] - [1.
PCH Core Voltage 本項目可以用來設定 PCH Core 電壓。數值以 0.010V 為間隔,變更的範圍由 0.700V 至 1.000V。 設定值有:[Auto] [0.70000] - [1.00000] Ring Down Bin 本項目用來開啟或關閉 Ring DownBin 功能。預設值為 [Enabled]。使用 OC mailbox 指令 0x19。 [Auto] 設定為預設值。 [Disabled] 處理器不會降低環比率且會遵守需求的環比限制。 [Enabled] 處理器將降低環比率且可能無觀察到最大環比需求。 請留意關閉此功能可能會導致處理器過壓。 Min. CPU Cache Ratio 本項目用來設定處理器的非核心比值至可能的最小值。請使用 <+> 與 <-> 鍵調整數 值。 設定值有:[Auto] [8] - [85] Max. CPU Cache Ratio 本項目用來設定處理器的非核心比值至可能的最大值。請使用 <+> 與 <-> 鍵調整數 值。 設定值有:[Auto] [8] - [85] Max.
以下項目只有在 Actual VRM Core Voltage 設為 [Manual Mode] 時才會出現。 CPU Core Voltage Override 本項目用來讓您透過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.600V 至 1.700V。 設定值有:[Auto] [0.60000] - [1.70000] 以下項目只有在 Actual VRM Core Voltage 設為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設定正數值偏移電壓。 [-] 設定負數值偏移電壓。 CPU Core Voltage Offset 本項目用來透過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 0.005V 至 0.635V。 設定值有:[Auto] [0.00500] - [0.
Offset Voltage 本項目用來設定處理器核心電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.001V 至 0.999V。 設定值有:[Auto] [0.00100] - [0.99900] 請儲存並重啟系統使變更生效。 Cache SVID Voltage 本項目可以設定環域要求的快取電壓。結果可能會受 Actual VRM Core Voltage 影 響。 設定值有:[Auto] [Manual Mode] [Adaptive Mode] 以下項目只有在 Cache SVID Voltage 設為 [Manual Mode] 時才會出現。 CPU Core Voltage Override 本項目可以用來設定快取電壓。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間 隔,變更的範圍由 0.600V 至 1.700V。 設定值有:[Auto] [0.60000] - [1.
以下項目只有在 CPU Graphics Voltage Mode 設定為 [Manual Mode] 時才會出現。 CPU Graphics Voltage Override 本項目可以用來設定 CPU 顯示卡電壓。請使用 <+> 與 <-> 鍵調整數值。數值以 0.005V 為間隔,變更的範圍由 0.600V 至 1.700V。 設定值有:[Auto] [0.60000] - [1.70000] 以下項目只有在 CPU Graphics Voltage 設為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設定正數值偏移電壓。 [-] 設定負數值偏移電壓。 CPU Graphics Voltage Offset 本項目用來設定處理器顯示卡電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.005V 為間隔,變更的範圍由 0.005V 至 0.635V。 設定值有:[Auto] [0.00500] - [0.
Offset Voltage 本項目用來設定 CPU L2 電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.001V 至 0.999V。 設定值有:[Auto] [0.00100] - [0.99900] 請儲存並重啟系統使變更生效。 CPU System Agent Voltage 本項目可以用來設定 CPU System Agent 電壓。 設定值有:[Auto] [Manual Mode] [Offset Mode] 以下項目只有在 CPU System Agent Voltage 設為 [Manual Mode] 時才會出現。 CPU System Agent Voltage Override 本項目用來透過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.001V 為間隔,變更的範圍由 0.700V 至 1.800V。 設定值有:[Auto] [0.70000] - [1.
DRAM VDDQ Voltage 本項目用來設定 DRAM IC 的 VDD 資料部分電源。請使用 <+> 與 <-> 鍵調整數值。 數值以 0.005V 為間隔,變更的範圍由 0.800V 至 1.435V。 設定值有:[Auto] [0.80000] - [1.43500] Advanced Memory Voltages IVR Transmitter VDDQ Voltage 本項目可以為記憶體控制器設定內部發射器的電壓。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.700V 至 2.200V。 設定值有:[Auto] [0.70000] - [2.20000] Memory Controller Voltage 本項目可以用來設定記憶體控制器電壓。請使用 <+> 與 <-> 鍵調整數值。數值 以 0.010V 為間隔,變更的範圍由 1.006V 至 2.006V。 設定值有:[Auto] [1.00600] - [2.
DRAM VPP Voltage 本項目可以設定 DRAM 啟動電源供應器的電源。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 1.500V 至 2.135V。 設定值有:[Auto] [1.50000] - [2.13500] DRAM VDD Switching Frequency 本項目可以 Mhz 為單位設定 DRAM VDD 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,變更的範圍由 0.750MHz 至 1.500MHz。 設定值有:[Auto] [0.75000] - [1.50000] DRAM VDDQ Switching Frequency 本項目可以 Mhz 為單位設定 DRAM VDDQ 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,變更的範圍由 0.750MHz 至 1.500MHz。 設定值有:[Auto] [0.75000] - [1.
PMIC0-3 DRAM VPP Voltage 本項目可以設定 DRAM 啟動電源供應器的電源。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 1.500V 至 2.135V。 設定值有:[Auto] [1.50000] - [2.13500] PMIC0-3 DRAM VDD Switching Frequency 本項目可以 Mhz 為單位設定 DRAM VDD 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,變更的範圍由 0.750MHz 至 1.500MHz。 設定值有:[Auto] [0.75000] - [1.50000] PMIC0-3 DRAM VDDQ Switching Frequency 本項目可以 Mhz 為單位設定 DRAM VDDQ 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,變更的範圍由 0.750MHz 至 1.500MHz。 設定值有:[Auto] [0.75000] - [1.
6.
6.
SA - PCI Express DMI ASPM 本項目用來設定 DMI ASPM 支援。 設定值有: [Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1] DMI Gen3 ASPM 本項目用來設定 DMI Gen3 ASPM 支援。 設定值有:[Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1] PEG - ASPM 本項目用來控制 PEG 0 的 ASPM 支援。若 PEG 不是目前使用的裝置則無效。 設定值有:[Disabled] [L0s] [L1] [L0sL1] PCI Express Clock Gating 本項目用來開啟或關閉每個連接埠的 PCI Express Clock Gating。 設定值有:[Disabled] [Enabled] 6.
Hardware Prefetcher 啟用或關閉 MLC 控制器。 設定值有:[Disabled] [Enabled] Adjacent Cache Line Prefetch 本項目可以讓處理器在 L2 Cache 進行預取反饋和資料,從而降低記憶體負荷時間, 改善系統效能。 設定值有:[Disabled] [Enabled] Intel (VMX) Virtualization Technology 當本項目設為 [Enabled] 時,啟動 Intel 虛擬技術(Virtualization Technology),讓 硬體平台可以同時執行多個作業系統。 設定值有:[Disabled] [Enabled] Per P-Core Control 設定值有:[Disabled] [Enabled] 以下項目只有在 Per P-Core Control 設定為 [Enabled] 時才會出現。 P-Core 0-5 請勿同時關閉所有 P-core 選項,否則 P-core 選項會在重新開機後重置。 設定值有:[Enabled] [Disabled] Per E-Core Control 設定值有:
Per Core Hyper-Threading 本選單的項目用來開啟或關閉每個核心的超執行緒。。 Hyper-Threading of Core 0-5 設定值有:[Disabled] [Enabled] Total Memory Encryption 本項目用來設定全記憶體加密(TME)以保護動態隨機存取記憶體資料免受物理攻 擊。 設定值有:[Disabled] [Enabled] Legacy Game Compatibility Mode 本項目設定為 [Enabled] 時,按下捲軸鎖定鍵可切換為效率核心, 同時捲軸鎖定指示 燈會亮起。 設定值有:[Disabled] [Enabled] CPU - Power Management Control 本項目用來管理與設定處理器電力。 Boot performance mode 在作業系統切換前允許您選擇 BIOS 的效能狀態。 設定值有:[Max Battery] [Max Non-Turbo Performance] [Turbo Performance] [Auto] Intel(R) SpeedStep(tm) 本項目可以支援兩個以上的頻
以下項目只有在 Acoustic Noise Mitigation 設為 [Enabled] 時才會出現。 Pre Wake Time 本項目讓您以 micro ticks 為單位設定最大 Pre Wake 隨機分派時 間。這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設定值有:[0] - [255] Ramp Up Time 本項目讓您以 micro ticks 為單位設定最大 Ramp Up 隨機分派時間。 這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設定值有:[0] - [255] Ramp Down Time 本項目讓您以 micro ticks 為單位設定最大 Ramp Up 隨機分派時間。 這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設定值有:[0] - [255] IA VR Domain Disable Fast PKG C State Ramp for IA Domain 需要配置此選項以在更深的 C-state 期間減少噪音。 [FALSE] 請勿在更深的 C
Package C State Limit 本項目可讓您設定處理器封包的 C-state 限制。設定為 [CPU Default] 會將其保 留為出廠預設值。設定為 [Auto] 將初始化最深的可用封包 C-State 限制。 設定值有:[C0/C1] [C2] [C3] [C6] [C7] [C7s] [C8] [C9] [C10] [CPU Default] [Auto] Thermal Monitor 本項目可讓您啟用或停用 Thermal Monitor。 設定值有:[Disabled] [Enabled] Dual Tau Boost 本項目可讓您開啟 Dual Tau Boost 功能。僅適用於桌機 35W/65W/125W sku。 啟用 DPTF 後,此功能將被忽略。 設定值有:[Disabled] [Enabled] 6.
Memory Configuration 本項目用來設定記憶體配置參數。 Memory Remap 本項目用來開啟或關閉 4GB 以上的記憶體 remap。 設定值有:[Enabled] [Disabled] Graphics Configuration 本項目用來選擇以處理器、PEG 顯示裝置或 PCIe 顯示裝置作為優先使用的顯示裝 置。 Primary Display 本項目用來選擇以處理器、PEG 顯示裝置或 PCIe 顯示裝置作為優先使用的顯 示裝置。 設定值有:[Auto] [CPU Graphics] [PEG Slot] [PCIE] iGPU Multi-Monitor 將此項目設定為 [Enabled] 以啟用整合與獨立顯示卡的多顯示器輸出。iGPU 共 享系統記憶體大小將固定為 64M。 設定值有:[Disabled] [Enabled] DVMT Pre-Allocated 本項目可以讓您選擇內部顯示裝置使用的 DVMT 5.
Map SATA Controller under VMD 本項目用來 map 或 unmap 本啟動連接埠至 VMD。 設定值有:[Disabled] [Enabled] 如果將 Map SATA Controller under VMD 設為 [Enabled] 時,請確認將 Map PCIE Storage under VMD 設為 [Disabled]。 PCI Express Configuration 本子選單中的項目可以讓您為不同的內建插槽配定 PCIe 速度。 子選單的項目會因主機板而異。關於實際設定與選項,請參考主機板的 BIOS。 6.
6.5 PCH 儲存裝置設定(PCH Storage Configuration) 當您進入 BIOS 設定程式時,BIOS 設定程式將自動偵測已安裝的 SATA 裝置。當未 偵側到 SATA 裝置時將顯示 Empty 。將捲軸往下捲動來顯示其他 BIOS 項目。 此選單中的項目可能因您的主機板而異。關於實際設定與選項,請參考主機板的 BIOS。 SATA Controller(s) 啟用或關閉 SATA 控制器。 設定值有:[Disabled] [Enabled] 以下項目只有在 SATA Controller(s) 設為 [Enabled] 時才會出現。 Aggressive LPM support 當本項目設定為 [Enabled] 時,可以讓 PCH 主動進入連接電源狀態。 設定值有:[Disabled] [Enabled] SMART Self Test S.M.A.R.T.
SATA6G 本項目可啟用或關閉選擇的 SATA 連接埠。 設定值有:[Disabled] [Enabled] SATA6G Hot Plug 指定此連接埠支援熱抽換功能。 設定值有:[Disabled] [Enabled] 6.
6.
DTBT Controller 0 Configuration DTBT Controller 0 設定值有:[Disabled] [Enabled] TBT Host Router 可以依據可用連接埠啟用主機路由器。 設定值有:[One Port] [Two Port] Extra Bus Reserved 本項目用來選擇 TBT Root Port Type。 [56] One port Host。 [106] Two port Host.
6.
Endorsement Hierarchy 本項目用來啟動或關閉 Endorsement Hierarchy。 設定值有:[Disabled] [Enabled] Physical Presence Spec Version 本項目用來選擇告訴作業系統支援 PPI 版本 1.2 或 1.3。 設定值有:[1.2] [1.3] 部分 HCK 測試可能未支援 PPI Spec 版本 1.3。 TPM 2.0 UEFI Spec Version 本項目可以選擇 TCG2 規格版本支援。 [TCG_1_2] 相容於 Windows 8 / Windows 10 模式。 [TCG_2] 支援新 TCG2 協定與事件格式,適用於 Windows 10 或更高版本。 6.
SR-IOV Support 若系統支援 SR-IOV 的 PCIe 裝置,本項目用來開啟或關閉 Single Root IO Virtualization Support 功能。 設定值有:[Disabled] [Enabled] 6.
USB Single Port Control 本項目用來啟動或關閉個別 USB 連接埠。 USB 連接埠的位置請參考主機板手冊裡 主機板構造圖 與 後側面板連接埠 的說 明。 6.11 網路協定堆疊設定(Network Stack Configuration) 本選單可讓您變更網路協定堆疊的各項相關設定。 Network stack 本項目用來啟動或關閉 UEFI 網路協定堆疊(Network Stack)功能。 設定值有:[Disabled] [Enabled] 以下的項目只有在 Network Stack 設為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support 本項目用來啟動或關閉 Ipv4/Ipv6 PXE 開機選項。 設定值有:[Disabled] [Enabled] 6.
6.13 HDD/SSD SMART 資訊(HDD/SSD SMART Information) 本選單顯示已連結裝置的 SMART 資訊。 本選單的顯示選項會依連接至主機板的裝置而異。關於實際設定與選項,請參考 主機板的 BIOS。 NVM Express 裝置不支援 SMART 資訊。 6.
ErP Ready 在 S4+S5 或 S5 休眠模式下關閉某些電源,減少待機模式下電力的流失,以符合歐 盟能源使用產品(Energy Related Product)的規範。當設定為 [Enabled] 時,其他 PME 選項將被關閉。RGB LED 指示燈與 RGB/可定址燈條接頭也會被關閉。 設定值有:[Disabled] [Enabled (S4+S5)] [Enabled (S5)] Power On By PCI-E 本項目用來啟動或關閉內建網路控制器或其他安裝的 PCI-E 網路卡的喚醒功能。 設定值有:[Disabled] [Enabled] Power On By RTC 本項目用來關閉或開啟即時時鐘(RTC)喚醒功能,啟用時您可自行設定天、小時、 分、秒以安排時間讓系統自動開機。 設定值有:[Disabled] [Enabled] 6.
HD Audio 本項目用來設定高傳真音效控制器。 [Disabled] 高傳真音效無條件關閉。 [Enabled] 高傳真音效無條件開啟。 Intel LAN 本項目用來開啟或關閉 Intel LAN。 設定值有:[Disabled] [Enabled] USB power delivery in Soft Off state (S5) 本項目用來當您的電腦處於 S5 狀態時開啟或關閉 USB 電源。 設定值有:[Disabled] [Enabled] Connectivity mode (Wi-Fi & Bluetooth) 本項目用來開啟或關閉 Wi-Fi 與藍牙連接模組。 設定值有:[Disabled] [Enabled] LED lighting 系統在工作狀態時 當系統在工作狀態時,本項目用來關閉或開啟 RGB LED 指示燈。 [All On] 所有 RGB 指示燈與功能指示燈將開啟。 [Stealth Mode] 所有 RGB 指示燈與功能指示燈將關閉。 [Aura Only] RGB 指示燈將開啟,功能指示燈將關閉。 [Aura Off] 功能指示燈開啟,RGB 指示
Serial Port 本項目可以啟動或關閉序列埠。 設定值有:[Enabled] [Disabled] 以下的項目只有在 Serial Port 設為 [Enabled] 時才會出現。 Change settings 本項目用來為 Super I/O 裝置選擇最佳設定。 設定值有:[Disabled] [Enabled] Intel Arc Graphics 本項目可以最佳化 Intel Arc Graphics 效能。 設定值有:[Enabled] [Disabled] 6.
7.
Voltage and Current Monitor CPU Core Voltage, 12V Voltage, 5V Voltage, 3.3V Voltage, Memory Controller Voltage [x.
CPU Fan Speed Low Limit 本項目用來設定風扇/水泵的最低速度警告值。當達到這個最低速度時,會出現 警告訊息。若設定為 [Ignore],將不會再出現警告訊息。 設定值有:[Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] 以下項目只有在 CPU Fan Profile 設為 [Manual] 時才會出現。 CPU Fan Point4 Temperature 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 CPU Fan Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的占空 比。 CPU Fan Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P3-P4 占空
CPU Fan Point1 Duty Cycle (%) 當溫度源小於 P1 溫度,風扇會運作於 P1 占空比。當溫度源大於 P1 溫度, 占空比會依據 P1-P2 與溫度源決定。使用 <+> 或 <-> 鍵調整風扇/水泵的占空 比。 Chassis Fan(s) Configuration Chassis Fan Q-Fan Control 本項目用來設定 Chassis Fan 運作模式。 [Auto Detect] 偵測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水 泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/ 水泵。 Chassis Fan Profile 本項目用來設定風扇/水泵適當的效能。選擇 [Manual] 時,當處理器 溫度超過 75°C 時,建議將風扇/水泵的占空比設為 100%。請留意 當風扇/水泵占空比不足導致過熱,會造成處理器效能限制。 設定值有:[Standard] [Silent] [Turbo] [Full Speed]
以下項目只有在 Chassis Fan 1-5 Profile 設為 [Manual] 時才會出現。 Chassis Fan Point4 Temperature 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵 調整溫度。 Chassis Fan Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調 整風扇/水泵的占空比。 Chassis Fan Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫 度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 Chassis Fan Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫 度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-
AIO Pump Q-Fan Control 本項目用來設定 AIO Pump 運作模式。 [Auto Detect] 偵測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/水泵。 AIO Pump Profile 本項目用來設定風扇/水泵適當的效能。選擇 [Manual] 時,當處理器溫度超過 75°C 時,建議將風扇/水泵的占空比設為 100%。請留意當風扇/水泵占空比不 足導致過熱,會造成處理器效能限制。 設定值有:[Standard] [Silent] [Turbo] [Full Speed] [Manual] 以下項目只有在 AIO Pump Profile 設為 [Standard]、[Silent]、[Turbo] 或 [Manual] 時才會出現。 AIO Pump Q-Fan Source 指派的風扇/水泵會依選擇的溫度來源運作。 設定值有:[CPU] [MotherBoard] [VRM]
以下項目只有在 AIO Pump Profile 設為 [Manual] 時才會出現。 AIO Pump Point4 Temperature 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 AIO Pump Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的占空 比。 AIO Pump Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 AIO Pump Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的占 空比。 AIO Pum
Chassis Intrusion Detection Support 當本項目設定為 [Enabled] 時可啟用機殼偵測功能。 設定值有:[Enabled] [Disabled] CPU Temperature LED Switch 當本項目設定為 [Enabled] 時可啟用 CPU_LED 指示燈在處理器高溫時亮起。 設定值有:[Enabled] [Disabled] 78 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 使用手冊
8.
Boot from Storage Devices 本項用來選擇想要執行的儲存裝置類型。 設定值有:[Ignore] [Legacy only] [UEFI only] Boot from PCI-E/PCI Expansion Devices 本項目用來選擇想要執行的 PCIe/PCI 擴充裝置類型。 設定值有:[Ignore] [Legacy only] [UEFI only] Secure Boot 本項目用來設定 Windows® 安全開機的相關參數以及管理系統金鑰,以提升系統在開 機自我檢測(POST)時的安全性,避免受到未授權的使用者與惡意軟體的危害 OS Type [Windows UEFI Mode] 本項目用來選擇安裝的作業系統。執行 Microsoft® 安全開機檢查。只有在 Windows® UEFI 模式或其他 Microsoft® 安全開機相容作業 系統中開機時選擇此項目。 [Other OS] 在 Windows® 非 UEFI 模式中開機時獲得最佳功 能。Microsoft® 安全開機功能僅支援 Windows® UEFI 模式。 Microsoft® 安全開機功能僅可在
Set New key 本項目用來由 USB 儲存裝置載入已下載平台金鑰(PK)。 Delete key 本項目用來移除系統中的 PK。當平台金鑰刪除後即無法使用安全啟 動金鑰。 設定值有:[Yes] [No] PK 檔必須格式化為一個基於時間認證變量的 UEFI 變量構造。 KEK Management KEK(金鑰交換金鑰 [Key-exchange Key] 或金鑰註冊金鑰 [Key-Enrollment Key] )用來管理簽名資料庫(db)與撤銷簽名資料庫(dbx)。 Key-exchange Key(KEK)指的是 Microsoft® Secure Boot Key-Enrollment Key(KEK)。 Save to file 本項目用來將平台金鑰(KEK)儲存至 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入已下載平台金鑰(KEK)。 Append Key 本項目用來由儲存裝置載入附加的 KEK,以管理附加的簽名資料庫 (db)與撤銷簽名資料庫(dbx)。 Delete key 本項目用來移除系統中的 KEK。 設定值有:[Yes] [No] KEK
DBX Management dbx(撤銷簽名資料庫)列出 db 項目中不再被信任且無法被載入之被禁止的圖 片影像。 Save to file 本項目用來儲存 dbx 至 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入已下載的 dbx。 Append Key 本項目用來由儲存裝置載入附加的 dbx,以管理附加的簽名資料庫 (db)與撤銷簽名資料庫(dbx)。 Delete key 本項目用來移除系統中的 dbx 檔。 設定值有:[Yes] [No] dbx 檔必須格式化為一個基於時間認證變量的 UEFI 變量構造。 Boot Configuration Fast Boot 本項目可以啟用或關閉開機時僅執行最少所需裝置。不會對 BBS 開機選項造 成影響。 設定值有:[Disabled] [Enabled] 以下項目只有在 Fast Boot 設為 [Enabled] 時才會出現。 Next Boot after AC Power Loss [Normal Boot] [Normal Boot] 電源中斷後,在下一次啟動時恢復至正常啟動速度。 電源中斷後,在下一次啟動時加快
以下項目只有在 Boot Logo Display 設為 [Disabled] 時才會出現。 Post Report 本項目可以選擇 POST 的等候時間或直到按下 ESC。 設定值有:[1 sec] - [10 sec] [Until Press ESC] Boot up NumLock State 本項目可以選擇鍵盤 NumLock 狀態。 設定值有:[On] [Off] Wait For ‘F1’ If Error 系統開機過程出現錯誤訊息時,本項目可讓系統等待您按下 鍵確認才會 繼續進行開機程序。 設定值有:[Disabled] [Enabled] Option ROM Messages [Force BIOS] [Keep Current] 選購裝置韌體資訊會在開機自我檢測時顯示。 在開機自我檢測時只顯示華碩開機圖示。 Interrupt 19 Capture 本項目用來開啟或關閉選購裝置韌體資訊以進行 Interrupt 19 Capture。 設定值有:[Enabled] [Disabled] AMI Native NVMe Driver Support 本項目用來開啟或關閉 A
Boot Option Priorities 本項目讓您自行選擇開機磁碟並排列開機裝置順序。依照 1st、2nd、3rd 順序分別 代表其開機裝置順序,而裝置的名稱將因使用的硬體裝置不同而有所差異。 • 欲進入 Windows® 安全模式時,請在開機自我檢測(POST)時按下 (Windows® 8 不支援這項功能)。 • 開機時您可以在 ASUS Logo 出現時按下 選擇啟動裝置。 Boot Override 這些項目會顯示可用的裝置。依照 1st、2nd、3rd 順序分別代表其開機裝置順序, 而裝置的名稱將因使用的硬體裝置不同而有所差異。點選任一裝置可將該將置設定 為開機裝置。 84 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 使用手冊
9.
9.1 華碩 EZ Flash 3 公用程式(ASUS EZ Flash 3 Utility) 本項目可以讓您執行華碩 EZ Flash 3 公用程式。按下 會出現再次確認的視 窗,請使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 華碩 EZ Flash 3 的說明。 9.
9.
9.4 華碩 SPD 資訊(ASUS SPD Information) 本選單顯示記憶體插槽的相關資訊。 9.
9.6 華碩 Armoury Crate 本項目用來讓您在 Windows® 作業系統中開啟或關閉 Armoury Crate 應用程式的下載 與安裝。Armoury Crate 應用程式可以幫助您管理與下載主機板最新的驅動程式與公 用程式。 Download & Install ARMOURY CRATE app 設定值有:[Disabled] [Enabled] 9.
10. 離開 BIOS 程式(Exit menu) 本選單可讀取 BIOS 程式出廠預設值與離開 BIOS 程式,並可儲存與取消對 BIOS 項 目的變更。您也可以由 Exit 選單進入 EZ Mode。 Load Optimized Defaults 本項目可以載入 BIOS 程式設定選單中每個參數的預設值。請選擇本項目或按下 ,便會出現一個確認對話視窗,選擇 OK 以載入預設值。 Save Changes & Reset 當您完成對 BIOS 設定程式所做的變更後,請選擇本項目或按下 ,便會出現一 個確認對話視窗,請選擇 OK 以儲存設定並離開 BIOS 設定程式。 Discard Changes & Exit 本項目可以放棄所做的變更,並回復原先儲存的設定。在選擇本項目或按下 鍵 後,將會出現一個確認對話視窗,請選擇 Yes 以放棄任何設定並載入原先儲存的設 定,同時離開 BIOS 設定程式。 Launch EFI Shell from USB drives 本項目可以讓您由含有資料系統的裝置中啟動 EFI Shell(shellx64.
11. 更新 BIOS 程式 華碩網站上提供最新的 BIOS 程式,可以強化系統的穩定度、相容性或執行效能,但 是執行 BIOS 程式更新具有潛在性風險,若是使用現有版本的 BIOS 程式未發生問題 時,請勿手動執行更新 BIOS 程式。不適當的 BIOS 程式更新可能會導致系統開機失 敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程式。 請造訪華碩網站(http://www.asus.com/support)來下載本主機板最新的 BIOS 檔 案。 以下工具程式項目提供您管理與更新主機板 BIOS 設定程式。 1. 華碩 EZ Flash 3:使用 USB 隨身碟更新 BIOS。 2. 華碩 CrashFree BIOS 3: 當 BIOS 檔案遺失或損毀時,可以使用 USB 隨身碟來 更新 BIOS。 11.1 華碩 EZ Flash 3(ASUS EZ Flash 3) 華碩 EZ Flash 3 程式讓您使用 USB 隨身碟輕鬆的更新 BIOS 程式。 請依照以下步驟透過華碩 EZ Flash 3 更新 BIOS 程式: 1.
11.2 華碩 CrashFree BIOS 3(ASUS CrashFree BIOS 3) 華碩最新自行研發的 CrashFree BIOS 3 工具程式,讓您在當 BIOS 程式和資料被病毒 入侵或毀損時,可以輕鬆的從含有最新或原始 BIOS 檔案的 USB 隨身碟中回復 BIOS 程式的資料。 請至 http://www.asus.com/support 網站下載最新 BIOS 檔案,並儲存在 USB 隨身 碟中。 回復 BIOS 程式 請依照下列步驟回復 BIOS 程式: 1. 啟動系統。 2. 將含有最新或原始 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 3. 接著工具程式便會自動檢查儲存裝置中是否存有 BIOS 檔案。當搜尋到 BIOS 檔案後,工具程式會開始讀取 BIOS 檔案並自動進入 ASUS EZ Flash 3 程式。 4.