Notebook PC Hardware User’s Manual EX PR ES S E2877 / Nov 2006
Contents Table of Contents Table of Contents 1. Introducing the Notebook PC About This User’s Manual ������������������������������������������������������������������������������������������ 6 Notes For This Manual ������������������������������������������������������������������������������������������� 6 Preparing your Notebook PC ������������������������������������������������������������������������������������� 9 2.
Contents Table of Contents (cont.) Switches and Status Indicators �������������������������������������������������������������������������������� 36 Switches - Above keyboard ��������������������������������������������������������������������������������� 36 Status Indicators �������������������������������������������������������������������������������������������������� 38 Multimedia Control Keys (on selected models) ��������������������������������������������������� 41 4.
Contents Table of Contents (cont.
1.
1 Introducing the Notebook PC About This User’s Manual You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the various components in the Notebook PC and how to use them. The following are major sections of this User’s Manuals: 1. Introducing the Notebook PC Introduces you to the Notebook PC and this User’s Manual. 2. Knowing the Parts Gives you information on the Notebook PC’s components. 3.
Safety Precautions 1 Introducing the Notebook PC The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene, or other chemicals on or near the surface. IMPORTANT! Disconnect the AC power and remove the battery pack(s) before cleaning.
1 Introducing the Notebook PC Transportation Precautions To prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still ON.
Preparing your Notebook PC 1 Introducing the Notebook PC These are only quick instructions for using your Notebook PC. Read the later pages for detailed information on using your Notebook PC. 1. Install the battery pack 1 2. Connect the AC Power Adapter 3 2 3. Open the Display Panel IMPORTANT! When opening, do not force the display panel down to the table or else the hinges may break! Never lift the Notebook PC by the display panel! 4. Turn ON the Notebook PC Press the power button and release.
1 10 Introducing the Notebook PC
2. Knowing the Parts Basic sides of the Notebook PC NOTE: Photos and icons in this manual are used for artistic purposes only and do not show what is actually used in the product itself.
2 Knowing the Parts Top Side Refer to the diagram below to identify the components on this side of the Notebook PC. NOTE: The keyboard will be different for each territory.
Knowing the Parts 1 Microphone (Built-in) 2 Camera Indicator 3 Multi-Position Camera (on selected models) 4 Display Panel Status Indicators (top) 6 Instant Keys 7 Keyboard 8 Touchpad and Buttons Fingerprint Scanner 10 Status Indicators (front) 2 The built-in mono microphone can be used for video conferencing, voice narrations, or simple audio recordings. The camera indicator shows when the built-in camera is in use. The camera may be auto-activated by supported software.
2 Knowing the Parts Bottom Side Refer to the diagram below to identify the components on this side of the Notebook PC. NOTE: The bottom side may vary in appearance depending on model. 1 2 3 8 4 7 5 6 WARNING! The bottom of the Notebook PC can get very hot. Be careful when handling the Notebook PC while it is in operation or recently been in operation. High temperatures are normal during charging or operation. Do not use on soft surfaces such as beds or sofas which may block the vents.
Knowing the Parts 2 Battery Pack 3 Battery Lock - Manual 4 Central Processor Unit (CPU) Compartment 2 The battery pack is automatically charged when the Notebook PC is connected to an AC power source and maintains power to the Notebook PC when AC power is not connected. This allows use when moving temporarily between locations. Battery time varies by usage and by the specifications for this Notebook PC. The battery pack cannot be disassembled and must be purchased as a single unit.
2 Knowing the Parts Right Side Refer to the diagram below to identify the components on this side of the Notebook PC. EXPRESS 1 2 3 4 5 6 7 8 9 10 11 Microphone Input Jack 1 The mono microphone jack (1/8 inch) can be used to connect an external microphone or output signals from audio devices. Using this jack automatically disables the built-in microphone. Use this feature for video conferencing, voice narrations, or simple audio recordings.
Knowing the Parts 6 Optical Drive Electronic Eject 7 Optical Drive Emergency Eject (location varies by model) 8 LAN Port Modem Port 2 The optical drive eject has an electronic eject button for opening the tray. You can also eject the optical drive tray through any software player or by right clicking the optical drive in Windows “My Computer.” The emergency eject is used to eject the optical drive tray in case the electronic eject does not work.
2 Knowing the Parts Left Side Refer to the diagram below to identify the components on this side of the Notebook PC. µ -DVI 1 2 3 4 5 Air Vents 1 The air vents allow cool air to enter and warm air to exit the Notebook PC. IMPORTANT! Make sure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating of the Notebook PC may occur.
Knowing the Parts Front Side 2 Refer to the diagram below to identify the components on this side of the Notebook PC. OFF 1 1 Audio Speaker System 2 Wireless Switch 1 ON 2 The built-in stereo speaker system allows you to hear audio without additional attachments. The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound (results improved with external stereo headphones or speakers). Audio features are software controlled.
2 Knowing the Parts Rear Side Refer to the diagram below to identify the components on this side of the Notebook PC. 1 1 Battery Pack 2 Power (DC) Input 3 Kensington® Lock Port 2 3 The battery pack is automatically charged when the Notebook PC is connected to an AC power source and maintains power to the Notebook PC when AC power is not connected. This allows use when moving temporarily between locations. Battery time varies by usage and by the specifications for this Notebook PC.
Knowing the Parts Power Station (optional) 2 The optional Power Station allows quick connection and disconnection to all your desktop computer peripherals. Dock your Notebook PC to expand its capabilities by emulating a powerful desktop computer when you are in your office or at home. Quickly detach your Notebook PC for instant portability. IMPORTANT: Make sure the power station’s power adapter is connected and has power before docking the Notebook PC.
2 Knowing the Parts Power Station (optional) Top Side 1 2 3 4 5 1 Power Station Docking Indicator 2 Dock/Undock Computer Button 5 The power station docking indicator lights when the Notebook PC is docked (by software) to the power station. When the Notebook PC is undocked using the Dock/Undock Computer Button or Windows “Undock Computer” command, this indicator will blink first and then turn OFF.
Power Station (optional) Knowing the Parts 2 Left Side 1 1 2.0 2 3 4 USB Port (2.0/1.1) The USB (Universal Serial Bus) port is compatible with USB 2.0 or USB 1.1 devices such as keyboards, pointing devices, cameras, hard disk drives, printers, and scanners connected in a series up to 12Mbits/sec (USB 1.1) and 480Mbits/sec (USB 2.0). USB allows many devices to run simultaneously on a single computer, with some peripherals acting as additional plug-in sites or hubs.
2 Knowing the Parts Power Station (optional) Rear Side 1 3 4 6 7 8 PS/2 Port 1 2 2 The PS/2 port is for connection to either an external PS/2 mouse or an external PS/2 keyboard. 2.0 USB Port (2.0/1.1) The USB (Universal Serial Bus) port is compatible with USB 2.0 or USB 1.1 devices such as keyboards, pointing devices, cameras, hard disk drives, printers, and scanners connected in a series up to 12Mbits/sec (USB 1.1) and 480Mbits/sec (USB 2.0).
Power Station (optional) Knowing the Parts 2 Rear Side (Cont.) 6 7 8 Parallel Port The 25-pin D-sub parallel/printer port supports native parallel devices such as laser/inkjet printers, or parallel-adapted device such as external hard drives, removable drives, or scanners. DVI Display (DVI-D) Output (on selected models) The Digital Video Interface port is designed to maximize video graphics output to flat panel LCD monitors or other DVI-compliant device.
2 Knowing the Parts Power Station (optional) Right Side 1 2 1 Power Station Eject Button 2 Kensington® Lock Port This is a mechanical (not electronic) button. Press this button firmly downwards to eject the Notebook PC from the power station. Turn OFF the Notebook PC or make sure attached devices are not in use and “Undock Computer” is successful in Windows. The Kensington® lock port allows the Notebook PC to be secured using Kensington® compatible Notebook PC security products.
3.
3 Getting Started Power System Using AC Power The Notebook PC power is comprised of two parts, the power adapter and the battery power system. The power adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the power cord to any 100V-120V as well as 220V240V outlets without setting switches or using power converters.
Getting Started Using Battery Power 3 The Notebook PC is designed to work with a removable battery pack. The battery pack consists of a set of battery cells housed together. A fully charged pack will provide several hours of battery life, which can be further extended by using power management features through the BIOS setup. Additional battery packs are optional and can be purchased separately through a Notebook PC retailer.
3 Getting Started Powering ON the Notebook PC The Notebook PC’s power-ON message appears on the screen when you turn it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you press [Tab] during the splash screen, standard boot information such as the BIOS version can be seen.
Getting Started Checking Battery Power The battery system implements the Smart Battery standard under the Windows environment, which allows the battery to accurately report the amount of charge left in the battery. A fully-charged battery pack provides the Notebook PC a few hours of working power. But the actual figure varies depending on how you use the power saving features, your general work habits, the CPU, system memory size, and the size of the display panel.
3 Getting Started Restarting or Rebooting After making changes to your operating system, you may be prompted to restart the system. Some installation processes will provide a dialog box to allow restart. To restart the system manually, click Windows Start button and select Shut Down and then choose Restart. (Screens are different depending on security settings.
Special Keyboard Functions Getting Started 3 Colored Hot Keys The following defines the colored hot keys on the Notebook PC’s keyboard. The colored commands can only be accessed by first pressing and holding the function key while pressing a key with a colored command. NOTE: The Hot Key locations on the function keys may vary depending on model but the functions should remain the same. Follow the icons instead of the function keys.
3 Getting Started Colored Hot Keys (Cont.) Speaker Down Icon (F11): Decreases the speaker volume (only in Windows OS) Speaker Up Icon (F12): Increases the speaker volume (only in Windows OS) Num Lk (Ins): Toggles the numeric keypad (number lock) ON and OFF. Allows you to use a larger portion of the keyboard for number entering. Scr Lk (Del): Toggles the “Scroll Lock” ON and OFF. Allows you to use a larger portion of the keyboard for cell navigation.
Getting Started Microsoft Windows Keys 3 There are two special Windows keys on the keyboard as described below. The key with the Windows Logo activates the Start menu located at the bottom left of the Windows desktop. The other key, that looks like a Windows menu with a small cursor, activates the properties menu and is equivalent to pressing the right mouse button on a Windows object.
3 Getting Started Switches and Status Indicators Switches - Above keyboard InstantFun PLUS Key Pressing this button will launch a multimedia player application to view DVDs, VCDs, videos, photos, or television programs (when equipped with a TV tuner); or listen to music CDs or files. Power4 Gear+ Key The Power4 Gear+ button toggles power savings between various power saving modes. The power saving modes control many aspects of the Notebook PC to maximize performance versus battery time.
Getting Started Switches - Above keyboard (Cont.) 3 Power Switch The power switch allows powering ON and OFF the Notebook PC and recovering from STD. Use the switch once to turn ON and once to turn OFF the Notebook PC. In Windows XP, this button can also be used to safely turn OFF the Notebook PC. The power switch only works when the display panel is opened. OFF ON Wireless Switch Enables or disables the built-in wireless LAN and Bluetooth (selected models).
3 Getting Started Status Indicators Top Drive Activity Indicator Indicates that the Notebook PC is accessing one or more storage device(s) such as the hard disk. The light flashes proportional to the access time. Number Lock Indicator Indicates that number lock [Num Lk] is activated when lighted. Number lock allows some of the keyboard letters to act as numbers for easier numeric data input. Capital Lock Indicator Indicates that capital lock [Caps Lock] is activated when lighted.
Using the Notebook PC Status Indicators (Cont.) 4 Front Power Indicator The power indicator lights when the Notebook PC is turned ON and blinks slowly when the Notebook PC is in the Suspend-to-RAM (Standby) mode. This indicator is OFF when the Notebook PC is turned OFF or in the Suspend-to-Disk (Hibernation) mode.
4 Using the Notebook PC Status Indicators (Cont.) Outside Power Indicator The power indicator lights when the Notebook PC is turned ON and blinks slowly when the Notebook PC is in the Suspend-to-RAM (Standby) mode. This indicator is OFF when the Notebook PC is turned OFF or in the Suspend-to-Disk (Hibernation) mode.
Using the Notebook PC Multimedia Control Keys (on selected models) 4 The multimedia control keys allows for convenient controlling of the multimedia application. The following defines the meaning of each multimedia control key on the Notebook PC. Use the [Fn] key in combination with the arrow keys for CD control functions. CD Play/Pause During CD stop, begins CD play. During CD play, pauses CD play. CD Stop During CD stop: Ejects the CD tray. During CD play: Stops CD play.
4 42 Using the Notebook PC
4.
4 Using the Notebook PC Operating System This Notebook PC may offer (depending on territory) its customers the choice of a pre-installed operating system such as Microsoft Windows XP. The choices and languages will depend on the territory. The levels of hardware and software support may vary depending on the installed operating system. The stability and compatibility of other operating systems cannot be guaranteed.
Using the Notebook PC NTFS Converter 4 1. Double-click the NTFS icon on the desktop. The conversion command will be executed once for each partition on your Notebook PC so you will have to answer additional questions. NOTE: If your local disk is already in NTFS format, “...is already NTFS” will be shown for the relevant hard disk drive. 2. Dismount is necessary for the conversion. Press Y to continue. 3. Restart your system and check the details of your local disk to see if conversion is successful.
4 Using the Notebook PC Software Recovery Partition (Windows® XP™ Home and Professional Editions) The Recovery Partition includes an image of the operating system, drivers, and utilities installed on your Notebook PC at the factory. The Recovery Partition provides a comprehensive recovery solution that quickly restores your Notebook PC’s software to its original working state, provided that your hard disk drive is in good working order.
Using the Notebook PC Software Recovery CDs (on selected models) 4 (Windows® XP™ Home and Professional Editions) The Recover CDs includes an image of the operating system, drivers, and utilities installed on your Notebook PC at the factory. The Recover CDs provides a comprehensive recovery solution that quickly restores your Notebook PC’s software to its original working state, provided that your hard disk drive is in good working order.
4 Using the Notebook PC Pointing Device The Notebook PC’s integrated touchpad pointing device is fully compatible with all two/three-button and scrolling knob PS/2 mice. The touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures can be avoided. A device driver is still required for working with some application software.
Using the Notebook PC Touchpad Usage Illustrations 4 Clicking/Tapping - With the cursor over an item, press the left button or use your fingertip to touch the touchpad lightly, keeping your finger on the touchpad until the item is selected. The selected item will change color. The following 2 examples produce the same results. Clicking Tapping Lightly but rapidly strike the touchpad. Press the left cursor button and release.
4 Using the Notebook PC NOTE: A software-controlled scrolling function is available after setting up the included touchpad utility to allow easy Windows or web navigation. Basic functions can be adjusted at the Windows control panel to allow comfortable clicking and tapping. Caring for the Touchpad The touchpad is pressure sensitive. If not properly cared for, it can be easily damaged. Take note of the following precautions.
Using the Notebook PC Storage Devices 4 Storage devices allow the Notebook PC to read or write documents, pictures, and other files to various data storage devices. This Notebook PC has the following storage devices: • Expansion Card • Optical drive • Flash memory reader • Hard disk drive Expansion Card One 26pin Express card slot is available to support one ExpressCard/34mm or one ExpressCard/54mm expansion card. This new interface is faster by using a serial bus supporting USB 2.
4 Using the Notebook PC Optical Drive Inserting an optical disc 1. While the Notebook PC’s power is ON, press 2. Gently pull on the drive’s front panel and slide the drive’s eject button and the tray will eject the tray completely out. Be careful not to touch out partially. the CD drive lens and other mechanisms. Make sure there are no obstructions that may get jammed under the drive’s tray. 3. Hold the disc by the edge and face the disc’s 4. Slowly push the drive’s tray back in.
Using the Notebook PC Optical Drive (Cont.) Removing an optical disc 4 Emergency eject Actual location will vary by model. Eject the tray and gently pry the edge of the disc upwards at an angle to remove the disc from the hub. The emergency eject is located in a hole on the optical drive and is used to eject the optical drive tray in case the electronic eject does not work. Do not use the emergency eject in place of the electronic eject.
4 Using the Notebook PC Flash Memory Card Reader Normally a PCMCIA memory card reader must be purchased separately in order to use memory cards from devices such as digital cameras, MP3 players, mobile phones, and PDAs.
Using the Notebook PC Connections 4 NOTE: The built-in modem and network cannot be installed later as an upgrade. After purchase, modem and/or network can be installed as an expansion card. Modem Connection The telephone wire used to connect the Notebook PC’s internal modem should have either two or four wires (only two wires (telephone line #1) is used by the modem) and should have an RJ-11 connector on both ends.
4 Using the Notebook PC Network Connection Connect a network cable, with RJ-45 connectors on each end, to the modem/network port on the Notebook PC and the other end to a hub or switch. For 100 BASE-TX / 1000 BASE-T speeds, your network cable must be category 5 or better (not category 3) with twisted-pair wiring. If you plan on running the interface at 100/1000Mbps, it must be connected to a 100 BASE-TX / 1000 BASE-T hub (not a BASE-T4 hub). For 10Base-T, use category 3, 4, or 5 twisted-pair wiring.
Using the Notebook PC Wireless LAN Connection (on selected models) 4 The optional built-in wireless LAN is a compact easy-to-use wireless Ethernet adapter. Implementing the IEEE 802.11 standard for wireless LAN (WLAN), the optional built-in wireless LAN is capable of fast data transmission rates using Direct Sequence Spread Spectrum (DSSS) and Orthogonal Frequency Division Multiplexing (OFDM) technologies on 2.4GHz/5GHz frequencies.
4 Using the Notebook PC Intel PROSet (3945) Wireless LAN (on selected models) Connecting to a network Press [FN F2] (or double click the Wireless Console icon on the taskbar). Four icons will appear as shown here. Click on the 1st setting to activate both Wireless & Bluetooth, or you may select the 2nd option for Wireless activation only. 1. Click Start | All Programs | Intel PROSet Wireless | Intel PROSet Wireless. 2. Select the Network by double clicking or click on connect. (Eg: WL-520G network) 3.
Using the Notebook PC ASUS Wireless LAN (on selected models) 4 Connecting to a network Press [FN F2] (or double click the Wireless Console icon on the taskbar). Four icons will appear as shown here. Click on the 1st setting to activate both Wireless & Bluetooth, or you may select the 2nd option for Wireless activation only. 1. Click Start | Programs | ASUS Utility | WLAN Card | ASUS WLAN Control Center. 2. On the left hand side menu, click Survey to start scanning for available networks in your area. 3.
4 Using the Notebook PC Windows Wireless Network Connection Connecting to a network Press [FN F2] (or double click the Wireless Console icon on the taskbar). Four icons will appear as shown here. Click on the 1st setting to activate both Wireless & Bluetooth, or you may select the 2nd option for Wireless activation only. 1. Click on Start and select Control Panel 2. Click on the icon Network Connections (If this icon cannot be seen, click “Switch to Classic View” on the left side menu. 3.
Using the Notebook PC Bluetooth Wireless Connection (on selected models) 4 Notebook PCs with Bluetooth technology eliminates the need for cables for connecting Bluetooth-enabled devices. Examples of Bluetooth-enabled devices may be Notebook PCs, Desktop PCs, mobile phones, and PDAs. d3 # m6 ㄓㄗ ㄢㄦ ㄔㄘ ㄣㄧ ? ㄕㄙ ㄤㄨ ㄖㄥ ㄩ 8 t ㄏㄒ ㄠㄡ 0+ 5 j ㄎㄑㄟ 2aㄍㄐㄞ ㄜㄋ ㄈㄝ ㄊㄛ ㄅ ㄉㄚ a/A ㄌ * 7p ㄇ 4gㄆ 1 Bluetooth-enabled mobile phones You can wireless connect to your mobile phone.
4 Using the Notebook PC Trusted Platform Module (TPM) (on selected models) The TPM, or Trusted Platform Module, is a security hardware device on the system board that will hold computer-generated keys for encryption. It is a hardware-based solution that an help avoid attacks by hackers looking to capture passwords and encryption keys to sensitive data. The TPM provides the ability to the PC or notebook to run applications more secure and to make transactions and communication more trustworthy.
Using the Notebook PC TPM Setup for Fingerprint Scanner 4 These instructions will show you how to use the fingerprint scanner to authenticate the Infineon TPM. 1. Initialize Infineon TPM Security Platform. 2. Enroll fingerprint using PSQL. 3. Setting Infineon Security Platform: Click Configure... on the “Advanced” page. 4. Check Enhanced Authentication and click Next.
4 Using the Notebook PC TPM Setup for Fingerprint Scanner (Cont.) 64 5. Choose UPEK Enhanced Authentication Provider. 6. Click Configure... in User Settings page. 7. Check the Enhanced Authentication and Next. 8. Select the UPEK Fingerprint Sensor and Next. 9. Enter the old password and a new passphrase. 10. Swipe finger to authenticate.
Using the Notebook PC TPM Setup for Fingerprint Scanner (Cont.) 4 11. Settings are complete. Authentication when accessing TPM in Infineon Security Platform will change from asking TPM basic password to Biometric device (Fingerprint Reader) or new passphrase. 12. This is the original screen before setting enhanced authentication. 13. This is the screen after setting enhanced authentication. 14.
4 Using the Notebook PC Clearing TPM Secured Data When Supervisor Password is installed, TPM Security Clear will appear. Use this item to clear all data secured by TPM. Important: Use should routinely backup your TPM secured data. Running Security Platform in Windows 66 You can launch the Security Platform application from Windows “Control Panel”. You can launch the Security Platform application from Windows “Start” menu.
Power Management Modes Using the Notebook PC 4 The Notebook PC has a number of automatic or adjustable power saving features that you can use to maximize battery life and lower Total Cost of Ownership (TCO). You can control some of these features through the Power menu in the BIOS Setup. ACPI power management settings are made through the operating system.
4 Using the Notebook PC Power State Summary STATE “Stand by” STR (“Stand by”) (Suspend-to-RAM) STD (“Hibernate”) (Suspend-to-Disk) Soft OFF ENTRY EVENT • “Stand by” through Windows Start button • Timer as set though “Power Management” in Windows Control Panel (higher priority) EXIT EVENT • Any device • Battery low • Hotkey (see “Colored Hotkeys” under “Special • Signal from modem port Keyboard Functions” in the previous section) • Power button or any key • Hotkey (see “Colored Hotkeys” under “Special
Using the Notebook PC Stand by and Hibernate 4 Power management settings can be found in the Windows control panel. The following shows the power options properties in Windows. You can define “Stand By” or “Shut down” for closing the display panel, pressing the power button, or activating sleep mode. “Stand by” and “Hibernate” saves power when your Notebook PC is not in use by turning OFF certain components.
4 Using the Notebook PC Fingerprint Scanner The fingerprint scanner can be used for instant and secure user authentication. Left or right click the fingerprint taskbar icon to open the menu to edit fingerprints or make control settings. You can launch the Control Center from Windows “Start” if the taskbar icon is not running. 1.3M MEGA PIXELS 1.3M MEGA PIXELS 70 If you have not configured a user, you will be directed to the “User Enrollment”.
Fingerprint Login Using the Notebook PC 4 The fingerprint scanner can be used to replace the system bootup and/or Windows login password check. To use this feature: 1. You must set a Supervisor Password on the “Security” page in BIOS SETUP UTILITY. 2. Password Check on the “Security” page in BIOS SETUP UTILITY must be set to [Fingerprint]. 3. Choose Power-on Security in the “Control Center”. 4. Select “Replace the power-on and hard...”. 5.
4 Using the Notebook PC SIM and Memory Card Installation IMPORTANT! Before installing a SIM or memory card, shut down the Notebook PC and remove the battery to prevent damage. 2 1 72 (1) Remove the screw to the memory and SIM compartment. (2) Remove a memory module as shown if there is one installed. This is necessary to install a SIM card. (4) Re-insert the memory module as shown if one was installed. (5) Tighten the screw to the memory and SIM compartment. 3 (3) Insert a SIM card as shown.
3G Watcher Software Using the Notebook PC 4 The 3G(1) Watcher software application will allow your Notebook PC to connect to 3G wireless networks normally used by 3G mobile phones. When connected, your Notebook PC can connect to the Internet just like using a wireless network. A shortcut to the 3G Watcher application will be placed on your desktop. Double-click it to launch the 3G Watcher software application.
4 Using the Notebook PC Watcher window Icons and indicators on the main window The main Watcher window provides status information and allows you to initiate and monitor data connections or make and receive phone calls (if voice is supported by your 3G modem and your service provider). The main window uses these indicators: Device status. If an icon of the 3G modem with an “X” is displayed, Watcher is unable to detect the 3G modem.
Using the Notebook PC 4 Roaming. You are connected to a network other than your local service provider’s. There may be a surcharge for roaming service. (This service may not be available.) New SMS message. Click the icon to open the SMS Express window and read your messages. When your SIM becomes full, this icon flashes and turns red. (Supported only on selected devices.) Data transmission. When the modem is connected to the network, the main Watcher window shows the amount of data received and sent.
4 76 Using the Notebook PC
Appendix Optional Accessories Optional Connections Glossary Declarations and Safety Statements Notebook PC Information 77
A Appendix Optional Accessories These items, if desired, come as optional items to complement your Notebook PC. USB Hub (Optional) Attaching an optional USB hub will increase your USB ports and allow you to quickly connect or disconnect many USB peripherals through a single cable. USB Keyboard and Mouse Attaching an external USB keyboard will allow data entry to be more comfortable. Attaching an external USB mouse will allow Windows navigation to be more comfortable.
Optional Connections Appendix A These items, if desired, may be purchased from third-parties. Printer Connection One or more USB printers can be simultaneously used on any USB port or USB hub.
A Appendix Bluetooth mouse (optional) 2. Install two “AA” batteries. OFF ON R 1. A Bluetooth icon should be located on your Windows taskbar. Right click the taskbar Bluetooth icon and choose Add New Connection. ESET 3. Turn ON the switch on the bottom of the mouse. 4. Push the “RESET” button on the bottom of the mouse. If you do not see the Bluetooth mouse here. Push the “RESET” button on the bottom of the mouse and click Refresh here. 5. Select “Express Mode” and click Next. 6.
Appendix Troubleshooting A Question: How do I check if my Bluetooth is ready? In “Device Manager”, check if “Bluetooth Personal Area Network” is available as shown here. Question: I cannot see my Bluetooth mouse in the list. What do I do? Click Refresh in the software and “RESET” on the mouse. Repeat if necessary. R OFF ON ESET Question: I already registered the Bluetooth mouse before. Why is it not working now? How do I connect to it? Double-click on the Bluetooth Icon.
A Appendix Glossary ACPI (Advanced Configuration and Power Management Interface) Modern standard for reducing power usage in computers. APM (Advanced Power Management) Modern standard for reducing power usage in computers. AWG (American Wire Gauge) NOTE: This table is for general reference only and should not be used as a source of the American Wire Gauge standard as this table may not be current or complete. Gauge AWG 33 32 30 29 27 26 25 Diam (mm) 0.18 0.19 0.20 0.25 0.30 0.35 0.40 0.
Appendix CPU (Central Processing Unit) A The CPU, sometimes called “Processor,” actually functions as the “brain” of the computer. It interprets and executes program commands and processes data stored in memory. Device Driver A device driver is a special set of instructions that allows the computer’s operating system to communicate with devices such as VGA, audio, Ethernet, printer, or modem. DVD DVD is essentially a bigger, faster CD that can hold video as well as audio and computer data.
A Appendix Kensington® Locks Kensington® locks (or compatible) allow the Notebook PC to be secured usually using a metal cable and lock that prevent the Notebook PC to be removed from a fixed object. Some security products may also include a motion detector to sound an alarm when moved. Laser Classifications As lasers became more numerous and more widely used, the need to warn users of laser hazards became apparent. To meet this need, laser classifications were established.
Appendix Suspend Mode A In Save-to-RAM (STR) and Save-to-Disk (STD), the CPU clock is stopped and most of the Notebook PC devices are put in their lowest active state. The Notebook PC enters Suspend when the system remains idle for a specified amount of time or manually using the function keys. The time-out setting of both Hard Disk and Video can be set by the BIOS Setup. The Power LED blinks when the Notebook PC is in STR mode. In STD mode, the Notebook PC will appear to be powered OFF.
A Appendix Declarations and Safety Statements DVD-ROM Drive Information The Notebook PC comes with an optional DVD-ROM drive or a CD-ROM drive. In order to view DVD titles, you must install your own DVD viewer software. Optional DVD viewer software may be purchased with this Notebook PC. The DVD-ROM drive allows the use of both CD and DVD discs. Regional Playback Information Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content.
Appendix Internal Modem Compliancy A The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN).
A Appendix Internal Modem Compliancy (Cont.) This table shows the countries currently under the CTR21 standard.
Appendix Federal Communications Commission Statement A This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
A Appendix FCC Radio Frequency Interference Requirements This device is restricted to INDOOR USE due to its operation in the 5.15 to 5.25GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25GHz to reduce the potential for harmful interference to co-channel of the Mobile Satellite Systems. High power radars are allocated as primary user of the 5.25 to 5.35GHz and 5.65 to 5.85GHz bands.
Appendix Wireless Operation Channel for Different Domains N. America Japan Europe ETSI 2.412-2.462 GHz 2.412-2.484 GHz 2.412-2.472 GHz A Ch01 through CH11 Ch01 through Ch14 Ch01 through Ch13 France Restricted Wireless Frequency Bands Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are: • • 10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz) 100mW for frequencies between 2446.5 MHz and 2483.
A Appendix UL Safety Notices Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National Electrical Code (NFPA 70).
Appendix Nordic Lithium Cautions (for lithium-ion batteries) A CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato. Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla fabbrica. Non disperdere le batterie nell’ambiente.
A Appendix Optical Drive Safety Information Laser Safety Information Internal or external optical drives sold with this Notebook PC contains a CLASS 1 LASER PRODUCT. Laser classifications can be found in the glossary at the end of this user’s manual. WARNING: Making adjustments or performing procedures other than those specified in the user’s manual may result in hazardous laser exposure. Do not attempt to disassemble the optical drive.
Appendix CTR 21 Approval (for Notebook PC with built-in Modem) A Danish Dutch English Finnish French German Greek Italian Portuguese Spanish Swedish 95
A Appendix Notebook PC Information This page is provided for recording information concerning your Notebook PC for future reference or for technical support. Keep this User’s Manual in a secured location if passwords are filled out.
Copyright Information No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
