VA32A 系列 液晶顯示器 使用手冊
初版 2016 年 6 月 版權 © 2016 ASUSTeK COMPUTER INC. 保留所有權利。 未經 ASUSTeK COMPUTER INC.
目錄 Notices ......................................................................................................... iv 安全資訊 ........................................................................................................ v 保養與清潔 .................................................................................................... vi 取回服務 ...................................................................................................... vii 1.1 歡迎使用! ...............................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
安全資訊 • 安裝本顯示器之前,請詳閱產品包裝內的說明文件。 • 為避免起火或觸電,請勿將顯示器暴露於下雨或潮濕的環境中。 • 切勿嘗試打開顯示器機殼。顯示器內的高壓電可能造成嚴重的人身傷害。 • 若電源中斷,切勿嘗試自行修復。請洽詢合格維修技術人員或經銷商。 • 使用本產品前,請務必正確連接所有纜線,並確認電源線並未損壞。若發 現任何損壞情形,請立即洽詢經銷商。 • 機殼背面或頂端的狹槽和開口為通風孔。請勿堵塞這些狹槽。除非通風良 好,否則切勿將本產品放置於散熱器或熱源附近或上方。 • 本顯示器只能使用標籤上註明的電源類型運作。若您不確定府上的電源類 型,請洽詢經銷商或當地的電力公司。 • 請使用符合當地電源標準的電池插頭。 • 請勿讓排插和延長線的電源過載。電源過載可能引發火災或造成觸電。 • 請避開多塵、潮濕和極溫的環境。請勿將顯示器放置於任何可能潮濕的環 境之中。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本裝置的插頭,避免顯示器因電源 突波而造成損壞。 • 切勿將任何異物塞入顯示器機殼開口內,也不可讓液體潑灑流入。 • 為確保適
限用物質含有情況標示: 保養與清潔 vi • 抬高顯示器或變更顯示器位置前,請先拔除纜線和電源線。請依照正確 的抬高方式放置顯示器。抬高或移動顯示器時,請握住顯示器的邊緣。 抬起顯示器時,切勿只握住底座或電源線。 • 清潔:請關閉顯示器電源並拔下電源線。使用不會造成刮傷的軟布清潔 顯示器表面,並以軟布沾少許中性清潔劑清除頑垢。 • 避免使用含酒精或丙酮的清潔劑,請使用液晶顯示器專用的清潔劑。切勿 將清潔劑直接噴灑於螢幕上,以免滲入顯示器內並引起觸電。
以下徵狀為顯示器正常現象: • 第一次使用本顯示器時,螢幕可能會因螢光燈的自然特性而出現閃爍的 情形。請關閉電源後重新開啟,讓閃爍情況消失。 • 不同的桌面樣式可能造成螢幕出現輕微亮度不均的情況。 • 顯示同樣的影像數小時後,當您切換影像時,可能會出現原有影像的殘 影。螢幕畫面會慢慢恢復正常,關閉電源開關數小時也可以改善此情況。 • 螢幕變黑、閃爍或無法運作時,請交由經銷商或維修中心處理。切勿自 行維修螢幕! 本手冊使用慣例 警告:可防止使用者因自行嘗試完成工作而受傷的資訊。 注意:可防止使用者因自行嘗試完成工作而損壞元件的資訊。 重要:使用者完成工作時必須遵守的資訊。 注意事項:協助使用者完成工作的訣竅和其他資訊。 更多詳細資訊 如需其他資訊與產品及軟體更新,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供關於 ASUS 硬體和軟體產品的最新資訊。請參閱 http://www.asus.com 2.
1.1 歡迎使用! 感謝您購買 ASUS® 液晶顯示器! ASUS 最新的寬螢幕液晶顯示器提供更清晰、更寬廣、更鮮明的畫面顯示, 以及許多增強觀賞體驗的功能。 透過這些功能,您可以盡情享受液晶顯示器所帶來的便利性及愉快的視覺體 驗! 1.
1.3 組合顯示器底座 1. 對準螺絲孔。 2. 將顯示器底座裝上腳架。 3.
1.4 連接纜線 1.4.1 液晶顯示器背面 5 HDMI VGA 4 1 6 1-3 2 7 2 3 HDMI VGA 8 9 10 11 1. 控制按鈕 6. DC 輸入埠 2. 喇叭 7. DisplayPort 3. Kensington 防盜鎖孔 8. HDMI 埠 4. USB 埠 電源 USB (5V/1.5A) 9. VGA 埠 5. 壁掛孔 11. 耳機插孔 10.
1.5 顯示器簡介 1.5.1 使用控制按鈕 使用顯示器底部的控制按鈕調整影像設定。按下按鍵 1-6 可啟動按鍵清單 頁。 弶⑬ 撚摇 巶‣弶㎅ QuickFit ᵬⵤ 㺼咋 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 1. 快速鍵 2: • 2. 這是快速鍵,預設設定為濾藍光。 快速鍵 1: • 3.
4. 輸入按鈕: • 5. 關閉按鈕: • 6. 退出 OSD 選單。 選單按鈕: • 7.
1.5.2 QuickFit 功能 QuickFit 功能包含三種圖案:(1) 方格 (2) 紙張尺寸 (3) 相片尺寸。 1. 方格圖案:方便設計師及使用者在一頁上編排內容及版面配置,達成一 致的外觀及質感。 Alignment Grid 2. 紙張尺寸:可讓使用者在螢幕上以實際尺寸檢視文件。 A4 B5 Letter A4 B5 Letter EXIT 3.
2.1 拆卸腳架 底座(適用於 VESA 壁掛式安裝) 本顯示器的可拆式底座是特別針對 VESA 壁掛式安裝而設計。 1. 拔下電源線和訊號線。謹慎地將顯示器正面朝下置於乾淨桌面上。 2. 取下固定轉軸蓋至腳架的螺絲。然後再取下轉軸蓋。 3. 取下四 (4) 顆固定腳架轉軸至顯示器後側的螺絲。 4. 從顯示器拆下總成(腳架與底座)。 1 2 3 4 • • • 2-1 建議您以軟布覆蓋桌面,以免損壞顯示器。 VESA 壁掛工具組 ( 100 x 100 mm) 為選購配件。 僅使用 UL 所列最小重量 負載 22.7 公斤的壁掛托架(螺絲大小:M4 x 0.
2.
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 ASUS VA32A Splendid 㣗㵔㣟ⷍ HDMI 2560 x 1440 @ 60Hz 杦㔭㣟ⷍ 㣗㵔㣟ⷍ ⅅ攠㣟ⷍ 弈ヰ㣟ⷍ ⟚摑㣟ⷍ sRGB㣟ⷍ 摯娾㣟ⷍ 㕕ヽ㣟ⷍ 3-1 1. 按下選單按鈕啟動 OSD 選單。 2. 按下 及 按鈕可切換選單中的選項。隨著您在圖示間移動,選項 名稱會跟著反白。 3. 若要選擇選單上的反白項目,請按下 4. 按下 5. 按下 按鈕可進入滑動列,然後再使用 的指示燈確定您的變更。 6.
3.1.2 1.
2.
3.
4.
5. 輸入選擇 選擇輸入來源。 ASUS VA32A 巶‣弶㎅ 㣗㵔㣟ⷍ HDMI 2560 x 1440 @ 60Hz VGA HDMI DisplayPort 6.
ASUS VA32A 䮹䰯士⩘ 㣗㵔㣟ⷍ HDMI 2560 x 1440 @ 60Hz 庒▜ 方㵎㇅䟸䂆 方㵎戳扔 ⼠₸㣟ⷍ ( 頁 2/2) 3-7 • Splendid Demo Mode:啟動 Splendid 功能展示模式。 • 音量:調整音度高低。 • ECO Mode:啟動節能模式可以省電。 • 選單設定:調整 OSD 螢幕的選單時間、DDC/CI 及透明度。 • 語言:選取 OSD 語言。 • 按鍵鎖:按下右側第二個按鈕超過五秒,即可啟動按鍵鎖定功能。 • 顯示資訊:顯示顯示器的資訊。 • 更多:返回系統設定的下一頁。 • 返回:返回系統設定的上一頁。 • 電源指示燈:開啟 • 電源鍵鎖:停用 • 恢復出廠模式:選擇是會將所有設定恢復為出廠預設模式。 關閉電源 LED 指示燈。 啟用電源鍵。 第 3 章:一般指示
7.
3.1.2.1 GamePlus 功能 GamePlus 功能可在遊玩不同類型的遊戲時,為玩家提供工具套件並打造更 出色的遊戲環境。此外,瞄準點功能是專為偏好第一人稱射擊 (FPS) 遊戲 的新玩家或新手而設計。 啟動 GamePlus: 1. 按下選單按鈕啟動 OSD 選單。 2. 按下 或 按鈕選擇捷徑。然後按下 3. 按下 或 按鈕選擇捷徑 1 或捷徑 2。 4. 按下 按鈕進入捷徑 1 或捷徑 2 子選單。 5. 按下 或 子選單。 6. 按下 或 選擇。 7. 重複按下 8.
3.2 規格 VA32AQ 機型 31.5 吋對角線 面板尺寸 (主動顯示區域:698.112(水平)x 392.688(垂直)mm) 最大解析度 2560(水平)x 1440(垂直) 亮度(標準) 250 cd/m2 對比率(標準) 1200:1 視角 (CR≤10) 178°(V);178°(H) 顯示色彩 10.7 億色(8 位元+FRC) 5ms(G 至 G) 反應時間 端子 音源喇叭 輸入: VGA x 1,HDMI x 1,DP x 1 音源輸入: 是 喇叭輸出: 4W x 2 耗電量 52W 不含 USB 充電(最大) 待機耗電量 < 0.5W 範圍 AC110V~ AC220V 電源關閉耗電量 < 0.5W 範圍 AC110V~ AC220V 實體 尺寸(包括底座) (HxWxD) 486.3 x 723.4 x 180 mm 包裝尺寸 (HxWxD) 534 x 784 x 120 mm 淨重(包含底座) 6.2 ±0.5 kg 毛重(估計值) 8.1 ±1.
3.
3.4 支援時序清單 VESA / IBM 模式支援時序 模式 解析度 (主動點) 解析度 (總點) 水平頻率 (KHz) 垂直頻率 (Hz) 像素 (MHz) DOS 720 x 400@70Hz 900 x 449 31.469 70.087 28.322 640 x 480@60Hz 800 x 525 31.469 59.940 25.175 640 x 480@72Hz 832 x 520 37.861 72.809 31.500 640 x 480@75Hz 840 x 500 37.500 75.000 31.500 800 x 600@56Hz 1024 x 625 35.156 56.250 36.000 800 x 600@60Hz 1056 x 628 37.879 60.317 40.000 800 x 600@72Hz 1040 x 666 48.077 72.188 50.000 800 x 600@75Hz 1056 x 625 46.875 75.000 49.