VG279 系列 LCD 顯示器 使用手冊
第一版 2018 年 10 月 版權所有© 2018 ASUSTeK華碩電腦公司,保留所有權利。 本手冊沒有任何部分,包括手冊描述的產品和軟體,可未經華碩電腦公司 (「華碩」,“ASUS”) 之明確書面許可,以任何形式或任何手段複製、傳播、轉錄、儲存於檢索系統,或翻譯成任何語 言,除購買者為保存文件進行之備份外。 若有以下情況,將不提供產品保證或服務,如:(1) 產品經修理、修改或更改,除該修理、改裝係 受華碩書面授權外,或 (2) 產品的序號列遭汙損或遺失。 華碩係「依原狀」提供本手冊,無任何明示或暗示等形式之擔保,包括但不限於暗示性或適銷性 或特定用途的保證。在任何情況下,華碩及其董事、職員、雇員或代理人皆無需承擔任何間接、 特殊、附帶或連帶之損害 (包括利潤損失、營業損失、無法使用或遺失資料及商業中斷損失等), 即使華碩已被告知本手冊或產品之任何缺陷或錯誤造成的損壞,可能會導致此類損失。 本手冊所載之規格及資料,僅供參考,並可不另行通知而隨時更改,且不應理解為華碩之承諾。 華碩不為本手冊可能出現的任何錯誤或不準確,負擔任何責任與義務,包括本手冊所述之產品和 軟體。 本手冊中出現的產品和公司名稱,可能是
目次 注意事項 ............................................................................................iv 安全資訊 .............................................................................................v 保養和清潔 ........................................................................................vi Takeback Services .........................................................................vii 第 1 章: 產品介紹 1.1 歡迎使用! ...........................................................................1-1 1.2 包裝內容 .
注意事項 聯邦通訊委員會聲明 本裝置符合 FCC 規定之第 15 篇。操作符合下列兩個條件: • 本裝置不會造成有害干擾,而且 • 本裝置會接受任何接收到的干擾,包括可能會影響裝置運作的干擾。 本設備通過測試並符合 FCC 規定之第 15 篇 B 級數位裝置的限制。這些限 制的用意在於提供適當防護,避免設備安裝在居住環境下產生有害干擾。本 設備會產生、使用和發射無線電頻能量,此外,若未依照指示安裝和使用, 可能會對無線電通訊產生不良干擾。然而,並不保證在特定安裝情況下不會 產生干擾。若本設備對收音機或電視機的收訊產生不良干擾 (可開啟然後關閉設備電源判定),使用者可透過以下方法消除干擾: • 重新調整接收天線的方向或位置。 • 增加設備和接收天線之間的距離。 • 將本設備連接到與接收器電源不同的電源插座上。 • 請向經銷商或有經驗的廣電技術人員尋求協助。 連接顯示器與顯示卡的遮蔽纜線,須符合 FCC 的規定。若未經相容性規 定之相關當局明示許可,擅自修改或改裝本裝置,使用者可能喪失操作 本設備之權限。 加拿大通訊部聲明 本數位裝置未超過加拿大通訊部無線電干擾法規所規定之數位裝置無線電
安全資訊 • 設定本顯示器之前,請詳讀產品包裝內的說明文件。 • 為預防起火或觸電,請勿將顯示器置於雨中或潮溼環境中。 • 請勿試圖打開顯示器的機殼。顯示器內部的高壓電可能造成人員嚴重 受傷。 • 若電源供應器損壞,請勿嘗試自行修復。請洽詢合格的維修技術人員 您的零售商。 • 使用本產品前,請確定已正確連接所有訊號線,而且電源線並未損壞。 若發現任何損壞,請立刻聯絡您的經銷商。 • 機殼背面或頂端的開口和通風口係用於散熱。請勿堵塞這些開口。 除非通風良好,否則請勿將本產品置於靠近散熱器或熱源的位置或 其上方。 • 本顯示器只能在產品標籤所示的電源環境下操作。若您不確定您家中的 電源規格,請洽詢您的經銷商或當地的電力公司。 • 使用符合當地電源標準的電源插頭。 • 不可使排插和延長線的電源過載。電源過載會導致起火或人員觸電。 • 避免在多灰塵、潮溼和極端溫度的環境中使用。請勿將顯示器置於可能 會使其受潮的區域。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本機的電源插頭。如此可預防顯示 器因電源突波而損壞。 • 請勿讓任何物體或液體進入顯示器機殼
保養和清潔 • 抬高或重新移位顯示器之前,請先拔下訊號線和電源線。顯示器移位 前,請依照正確的抬高方法。抬高或移動顯示器時,請握住顯示器的邊 緣。請勿以拉抬底座或訊號線的方式抬高顯示器。 • 清潔。關閉顯示器的電源,然後拔下電源線。使用無毛球且不會刮傷螢 幕的布清潔顯示器表面。可用沾有中性清潔劑的布清除頑垢。 • 避免使用含有酒精或丙酮的清潔劑。使用顯示器專用的清潔劑。請勿直 接將清潔劑噴灑於螢幕上,否則可能滲入顯示器內並造成人員觸電。 若顯示器發生以下情況,屬於正常現象: • 由於螢光燈的特性,初次使用螢幕時,畫面可能會閃爍。請關閉電源開 關,然後再重新開啟,確定閃爍現象消失。 • 不同的桌面模式可能導致螢幕有輕微亮度不均的情況。 • 顯示同一幅影像數小時後,切換影像時可能會出現前張影像的殘影。殘 影會慢慢消失,或者您可以開關電源數小時消除此情況。 • 螢幕變黑、閃爍或完全無法運作時,請洽詢您的經銷商或服務中心進行 修復。請勿自行修理螢幕! 本手冊使用的慣語 警告:執行作業作時,避免人員受傷的資訊。 注意:執行作業時,避免零組件損壞的資訊。 重要:執行作業時「必須」遵守的資訊。
其它詳細資訊來源 如需其它資訊和產品與軟體的更新程式,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供有關 ASUS 硬體和軟體產品的最新資訊。請連至 http://www.asus.com 取得相關資訊。 2. 選用的說明文件 您的產品包裝內可能有經銷商所提供的選用說明文件。產品的標準 包裝中不含此類文件。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.
viii
1.1 歡迎使用! 感謝您購買 ASUS® LCD 顯示器! ASUS 最新的寬螢幕 LCD 顯示器提供更寬廣、更明亮和更清晰的顯示,以 及許多可增強觀看感受的功能。 您可藉由這些功能享受到本顯示器帶給您的便利與快樂的視覺體驗! 1.
1.3 顯示器介紹 1.3.1 正面圖 1 2 3 4 5 1. ( • 開啟 OSD 功能表。啟動所選的 OSD 功能表項目。 • 增加/減少值或向上/向下/向左/向右移動選擇。 • 顯示器進入待機狀態或顯示「無信號輸入」訊息時,顯示輸入選 項列。 2. 按鈕 • 離開 OSD 功能表項目。 • 顯示器進入待機狀態或顯示「無信號輸入」訊息時,顯示輸入選 項列。 • 3. 長按 5 秒即可開啟和關閉「按鍵鎖」功能。 按鈕: • GamePlus 快速鍵。向上/向下移動 按下 ( )以確認所需的功能。 • 顯示器進入待機狀態或顯示「無信號輸入」訊息時,顯示輸入選 項列。 4.
• 5. 顯示器進入待機狀態或顯示「無信號輸入」訊息時,顯示輸入選 項列。 電源按鈕/電源指示燈 • 開啟/關閉顯示器電源。 • 電源指示燈的顏色定義如下表所示。 1.3.2 狀態 說明 白色 開 琥珀色 待機模式/無信號輸入 熄滅 關 背面圖 8 1. DC-IN 連接埠。此連接埠用於連接電源線。 2. DVI(雙通道)連接埠。此 24 針腳連接埠供 PC(個人電腦)DVI-D 數位訊號連線之用。 3. HDMI 連接埠。此連接埠用於連接 HDMI 相容裝置。 4. DisplayPort。此連接埠用於連接 DisplayPort 相容裝置。 5. 音訊輸入連接埠。此連接埠透過隨附的音訊訊號線可連接 PC 音訊源。 6. 耳機插孔。只有在連接 HDMI/DisplayPort 訊號線時,才能使用這個連 接埠。 7. Kensington 鎖插槽。 8.
1.3.3 GamePlus 功能 GamePlus 功能將提供一組工具組,讓玩家執行各種類型的遊戲時,創造更 好的遊戲環境。你可以在用 4 種不同的十字瞄準線選項重疊的十字瞄準線 中選擇一個最適合於正在進行中遊戲的選項。您也可以將螢幕定時器放置在 顯示器的左邊,以便您掌握遊戲的進行時間;FPS(每秒訊框數)計數器可 以讓您得知遊戲進行的順利程度。「顯示對齊」會在螢幕的 4 邊顯示對齊 線,以便確實對齊多台螢幕。 如何啟動 GamePlus: 1. 請按下 GamePlus 熱鍵。 2. 向上/向下移動 3. 按下 ( ( )按鈕將選擇不同的功能。 ) 按鈕或向右移動 ( ) 按鈕將確認您選擇的功能, 向上/向下移動 ( ) 按鈕可瀏覽設定。向左移動 將返回、關閉並離開。 4.
1.3.
1-6 第 1 章:產品介紹
2.1 組裝顯示器支架/底座 組裝顯示器底座: 1. 將顯示器正面朝下置於桌上。 2. 將底座接上支架,確定支架上的固定片插入底座的溝槽內。 3.
2.2 調整顯示器 • 為了取得最佳觀賞角度,我們建議您先從所有角度觀看顯示器,然後再 將顯示器調整到您認為最舒適的觀看角度。 • 變更角度時請握住底座,避免顯示器掉落。 • 建議的調整角度為 +33° 至 -5°(傾斜時)/+90° 至 -90°(轉動時)/±130 mm(進行高度調整時)/90°(直向檢視時)。 -5° ~ +33° 130mm 90° 0° 90° 調整觀看角度時,顯示器輕微震動是正常的情況。 以顯示器為中心旋轉 1. 將顯示器抬升至最高位置。 2. 將顯示器傾斜至最大角度。 3.
2.3 拆開支架/底座(適用於 VESA 壁掛式安裝) 此顯示器的可拆式支架 / 底座是專為 VESA 壁掛式安裝所設計。 拆開支架 / 底座: 1. 將顯示器正面朝下置於桌上。 2. 取下四個螺絲孔中的橡膠填充物。(圖 1) 3. 取下底座(圖 2)。 4.
2.4 接線 依下列指示連接訊號線: • • 連接電源線: a. 將電源變壓器牢牢插入螢幕的 DC 輸入。 b. 將電源線的一末端插入電源變壓器,再將另一末端插入電源 插座。 連接 DisplayPort/DVI/HDMI 訊號線: a. 將 DisplayPort/DVI/HDMI 訊號線的一端連接到顯示器的 DisplayPort/DVI/HDMI 連接埠。 b. 將 DisplayPort/DVI/HDMI 訊號線的另一端連接到電腦的 DisplayPort/DVI/HDMI 連接埠。 c. 鎖緊 2 顆螺絲固定 DVI 接頭。 • 若要連接音訊訊號線:將音訊訊號線的一端連接至顯示器的音訊輸入連 接埠,並將另一端連接至電腦的音訊輸出插孔。 • 若要使用耳機:HDMI 或 DisplayPort 信號輸入時,將插頭的那一端連接 到顯示器的耳機插孔。 2.
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 ASUS VG279 比賽模式 1920x1080@ 144Hz GameVisual 風景模 式 比賽模 式 電影模 式 RTS/ R P G 模 式 FPS 模 式 sRGB 模 式 MOB A M o d e 1. 按下 2. 向上 / 向下移動 ( ) 按鈕以導覽各項功能。反白顯示所需的設 定,並按下 ( ) 按鈕啟動該設定。如果所選擇的功能有子選單, 請再次向上/向下移動 ( ) 按鈕導覽子選單功能。反白顯示所需的 功能,並按下 ( ) 按鈕或向右移動 ( ) 按鈕啟動該功能。 3. 向上/向下移動 4. 若要離開並儲存 OSD 選單,請重複按下 按鈕或重複向左移動 ( ),直到 OSD 選單關閉為止。若要調整其它功能,請重複步驟 1-3。 3.1.2 1.
2.
3. 色彩 在此選單中設定所需的色彩設定。 色彩 ASUS VG279 比賽模式 1920x1080@ 144Hz 亮度 對比 彩度 色溫 膚色 S m a rt View 4.
• Adaptive-Sync/FreeSync(僅限 DisplayPort/HDMI):能夠讓支 援 Adaptive-Sync/FreeSync* 的圖形來源按照典型的內容訊框率動 態地調整顯示器更新率以達到高效率用電,流暢及低延遲的顯示更 新。 若要啟動 Adaptive-Sync/FreeSync,請先關閉 ELMB 功能。 * 只能在 40 Hz ~ 144 Hz 之間啟動 Adaptive-Sync/FreeSync。 * 關於支援的 GPU、最低 PC 系統和驅動程式需求,請聯絡 GPU 製造商。 • ELMB(僅限 DisplayPort/DVI):可開啟 / 關閉 ELMB (Extreme Low Motion Blur) 功能。更新頻率為 85Hz、100Hz 或 120Hz 時, 可使用此功能(僅限 DisplayPort)。 若要啟動 ELMB,請先關閉 Adaptive-Sync/FreeSync 功能。 • Shadow Boost:暗色強化調整螢幕 gamma 曲線,增加影像中的 暗色調,讓暗色場景與物件更容易被看見。 此功能僅適用於競賽模式、RTS/RPG 模式、
6. 輸入選擇 此功能可供您選擇所需的輸入來源。 輸入選擇 ASUS VG279 比賽模式 1920x1080@ 144Hz DVI HDM I Displ a y P o r t 7.
8.
3.2 規格總覽 面板類型 面板大小 最大解析度 畫素間距 亮度(一般) 對比比例(一般) 對比比例(最大) 視角(水平/垂直)CR > 10 顯示色彩 回應時間 色溫選項 類比輸入 數位輸入 耳機插孔 音訊輸入 喇叭(內建) USB 3.0 連接埠 顏色 電源 LED 傾角 旋轉 高度調整 VESA 壁掛式安裝 Kensington 鎖 電壓 耗電量 溫度(運作時) 溫度(未運作時) 尺寸(寬 X 高 X 深)不 含支架 尺寸(寬 X 高 X 深)含 支架 重量(預估值) 多語顯示 TFT LCD 27 吋(16:9、68.6 cm)寬螢幕 1920 x 1080 0.311 mm x 0.311 mm 400 cd/m2 1000:1 100,000,000:1(ASCR 開啟時) 178°/178° 16.7 M 3 毫秒(灰階對灰階) 4 種色溫 無 HDMI x 1、DisplayPort v1.
配件 規範和標準 DisplayPort 訊號線(選配)、HDMI 訊號線(選 配)、DVI(雙連結)訊號線(選配)、音訊訊號 線、電源變壓器、電源線、快速使用指南、保固卡 UL/cUL、CB、CE、ErP、FCC、CCC、CU、 RCM、BSMI、VCCI、RoHS、J-MOSS、WEEE、 Windows 7、8.
3.
3.
3.5 支援的操作模式 解析度頻率 螢幕更新頻率 水平 640x350 70Hz 31.469KHz 640x350 85Hz 37.861KHz 640x480 60Hz 31.469KHz 640x480 67Hz 35KHz 640x480 75Hz 37.5KHz 640x480 85Hz 43.269KHz 720x400 70Hz 31.469KHz 720x400 85Hz 37.927KHz 800x600 56Hz 35.156KHz 800x600 60Hz 37.897KHz 800x600 72Hz 48.077KHz 800x600 75Hz 46.875KHz 800x600 85Hz 53.674KHz 832x624 75Hz 49.725KHz 848x480 60Hz 31.02KHz 1024x768 60Hz 48.363KHz 1024x768 70Hz 56.476KHz 1024x768 75Hz 60.
解析度頻率 螢幕更新頻率 水平 1920x1080 60Hz 1920x1080 60Hz 66.587KHz 67.5KHz 1920x1080* (DVI/DP/HDMI) 85Hz 95.43KHz 1920x1080* (DVI/DP/HDMI) 100Hz 113.3KHz 1920x1080* (DVI/DP/HDMI) 120Hz 137.2KHz 1920x1080* (DVI/DP) 144Hz 158.11KHz 640x480P (HDMI) 59.94/60Hz 31.469KHz/31.5KHz 720x480P (HDMI) 59.94/60Hz 31.469KHz/31.5KHz 720x576P (HDMI) 50Hz 31.25KHz 1280x720P (HDMI) 50Hz 37.5KHz 1280x720P (HDMI) 59.94/60Hz 44.955KHz/45KHz 1440x480P (HDMI) 59.94/60Hz 31.469KHz/31.