VivoPC VM Series User Manual
E8901 Revised Edition V2 January 2014 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual.............................................................................................. 4 Conventions used in this manual................................................................ 4 Typography.......................................................................................................... 4 Package contents................................................................................................ 5 Getting to know your VivoPC 7 Features...............
About this manual This manual provides information about the hardware and software features of your PC, organized through the following chapters: Chapter 1: Getting to know your VivoPC This chapter details the hardware components of your VivoPC. Chapter 2: Using your VivoPC This chapter provides you with information on using your VivoPC. Chapter 3: Memory upgrade This chapter provides you with information on how to upgrade the memory modules of your VivoPC.
Package contents Your VivoPC package contains the following items: AC power adapter* VivoPC VM Series Technical documentations Power cable* NOTES: • *Actual product specifications and package contents may vary with your VivoPC’s model type or with country or region. • If the device or its components fail or malfunction during normal and proper use within the warranty period, bring the warranty card to the ASUS Service Center for replacement of the defective components.
VivoPC VM Series
1 Getting to know your VivoPC
Features Front panel Top cover The removable top cover allows you access to the hard disk drive and the memory modules. IMPORTANT! Before removing the top cover, turn off your VivoPC and unplug the power cable. Audio speakers Your VivoPC uses SonicMaster technology to provide hi-fi sound quality, with richer bass sounds, straight from the built-in audio speakers. Drive activity indicator This indicator lights up when your VivoPC is accessing the internal storage drive.
Left side Air vents The air vents on the left side allow cooler air to enter your VivoPC chassis. IMPORTANT! For optimum heat dissipation and air ventilation, ensure that the air vents are free from obstructions.
Rear panel Power button The power button allows you to turn the VivoPC on or off. You can also press the power button once to put your VivoPC to sleep mode. Memory card slot The built-in memory card reader enables your PC to read and write data to and from MMC/SD cards. Top cover lock latch + Kensington security slot The top cover lock latch fastens the top cover on your VivoPC. The Kensington security slot allows you to secure your VivoPC using Kensington® security products. USB 2.
VGA port The 15-pin VGA port supports a standard VGA-compatible device such as a monitor or projector to allow viewing on a larger external display. LAN port The eight-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network. Line-in port The line-in port allows you to connect an external audio device such as an audio mixer, disc player, cassette tape player, or an additional microphone.
Rear air vents The air vents on the rear allow warm air to exit the VivoPC. IMPORTANT! For optimum heat dissipation and air ventilation, keep the air vents at least 10cm away from any obstructions. Power input (DC 19V) The supplied power adapter converts AC power to DC power for use with this jack. Power supplied through this jack supplies power to the PC. To prevent damage to the PC, always use the bundled power adapter. WARNING! The power adapter may become warm to hot when in use.
Using your VivoPC 2
Getting started Connect the AC power adapter to your VivoPC To connect the AC power adapter to your VivoPC: A. Connect the AC power cord to the AC/DC adapter. B. Plug the AC power cord into a 100V~240V power source. C. Connect the DC power connector into your VivoPC’s power (DC) input port. NOTE: The power adapter may vary in appearance, depending on models and your region.
IMPORTANT! • We strongly recommend that you use only the AC power adapter and cable that came with your VivoPC. • We strongly recommend that you use a grounded wall socket while using your VivoPC. • The socket outlet must be easily accessible and near your VivoPC. • To disconnect your VivoPC from its main power supply, unplug your VivoPC from the power socket. NOTE: Power adapter information: • Input voltage: 100-240Vac • Input frequency: 50-60Hz • Rating output current: 3.
Connect a display panel to your VivoPC You can connect a display panel or projector to your VivoPC that has the following connectors: • HDMI connector • VGA connector • DVI connector (use with an HDMI to DVI adapter or VGA to DVI adapter) NOTE: The HDMI to DVI adapter and VGA to DVI adapter are sold separately. To connect a display panel to your VivoPC: Connect a display cable either to the HDMI port or the VGA display port.
Connect the USB cable from keyboard or mouse You can connect generally any USB keyboard and mouse to your VivoPC. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your VivoPC: Connect the USB cable from your keyboard and mouse to any of the USB 2.0 ports of your VivoPC. Connecting keyboard or mouse via USB 2.
Turn on your Vivo PC Press the power button to turn on your VivoPC.
Turning your VivoPC off If your VivoPC is unresponsive, press and hold the power button for at least four (4) seconds until your VivoPC turns off. Putting your VivoPC to sleep To put your VivoPC on Sleep mode, press the Power button once. Entering the BIOS Setup BIOS (Basic Input and Output System) stores system hardware settings that are needed for system startup in the VivoPC. In normal circumstances, the default BIOS settings apply to most conditions to ensure optimal performance.
Quickly enter the BIOS To quickly enter the BIOS: • Press the power button for at least four (4) seconds to shut down your VivoPC, then press the power button again to turn your VivoPC back on, then press or during POST. • When your PC is off, disconnect the power cord from your VivoPC’s power connector. Reconnect the power cable and press the power button to turn on your VivoPC. Press or during POST.
Memory upgrade 3
Upgrading memory modules Your VivoPC comes with two SO-DIMM memory slots that allow you to install two 2 GB, 4 GB, or 8GB unbuffered with non-ECC DDR3 204-pin SO-DIMMs for a maximum of 16 GB memory. IMPORTANT! You can only install DDR3 SO-DIMM to the VivoPC’s DIMM slots. NOTE: Refer to http://www.asus.com for the list of compatible DIMMs. To install or upgrade the memory modules: 22 1. Turn off your VivoPC. 2. Disconnect all cables and peripherals. 3. Place the VivoPC on a stable and flat surface.
HD D 4. Press down the latch at the rear panel to release the top cover. 5. Slide the top cover towards the rear of VivoPC until it is detached from the chassis. 6. Remove the cover and set aside. 3.5” HD 3.
7. Carefully slide the HDD or the drive tray adapter (with SSD inside) from the SATA connector, then remove it from the drive bay.
HD 8. Prepare memory module. 9. Release the screw that secures the SO-DIMM slot cover, then pry the slot cover open. Serial ATA connector Memory Memory SO-DIMM slot cover Serial ATA HDD drive bay 10. Align and insert the memory module into the slot (A) and press it down (B), until it is securely seated in place.
11. Replace the SO-DIMM slot cover and secure it with the screw. 12. For HDD, match the rubber heads of the screws with the four screw slots on the drive bay. 26 For SSD, match the rubber heads of the screws with the three screw slots on the drive bay.
13. Carefully place the Serial ATA HDD or SSD drive tray adapter (with SSD inside) into the drive bay, then slide the drive towards the SATA connector.
14. Replace the top cover then slide it towards the front of VivoPC to re-attach. 15. Lock the latch to securely fasten the top cover to the chassis.
Appendix
Safety information Your VivoPC is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface. Openings on the chassis are for ventilation.
Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users DO NOT throw the VivoPC in municipal waste. This product has been designed to enable proper reuse of parts and recycling.
Regulatory notices REACH Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment.
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
France Restricted Wireless Frequency Bands Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are: • • 10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz) 100mW for frequencies between 2446.5 MHz and 2483.5 MHz NOTE: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz.
This requirement is likely to change over time, allowing you to use your wireless LAN card in more areas within France. Please check with ART for the latest information (www.art-telecom.fr) NOTE: Your WLAN Card transmits less than 100mW, but more than 10mW. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
CE Mark Warning CE marking for devices without wireless LAN/Bluetooth The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC “Electromagnetic compatibility” and 2006/95/EC “Low voltage directive”.
ENERGY STAR complied product ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices. All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor and computer are automatically set to sleep after 10 and 30 minutes of user inactivity.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax E-mail Web site Technical Support Telephone Fax Online support 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw http://www.asus.com +86-21-3842-9911 +86-21-5866-8722, ext. 9101# http://support.asus.com/techserv/techserv.
EC Declaration of Conformity We, the undersigned, Manufacturer: ASUSTeK COMPUTER INC. Address, City: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN Country: TAIWAN Authorized representative in Europe: ASUS COMPUTER GmbH Address, City: HARKORT STR.
EC Declaration of Conformity We, the undersigned, Manufacturer: ASUSTeK COMPUTER INC. Country: TAIWAN Address, City: Authorized representative in Europe: Address, City: Country: declare the following apparatus: 4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN ASUS COMPUTER GmbH HARKORT STR.
DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Responsible Party Name: Asus Computer International 800 Corporate Way, Fremont, CA 94539. Address: Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : VivoPC Model Number : VM60 Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules.
DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Responsible Party Name: Address: Asus Computer International 800 Corporate Way, Fremont, CA 94539. Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Vivo PC Model Number : VM40B Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules.
