VP228系列 液晶显示器 用户指南
目录 声明 iii 安全信息................................................................................iv 保养和清洁 .............................................................................vi 1.1 欢迎使用! ..................................................................................... 1-1 1.2 物品清单 ......................................................................................... 1-1 1.3 组装显示器 ..................................................................................... 1-2 1.4 连接线缆 ........
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。 其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。 本设备会产生、 使用并且辐射无线电波,如果不按照制造商的说明进行安装和使用,可能会 对无线电通讯产生有害干扰。 但是,不能保证在特定安装条件下不会出现 干扰。 如果本设备对无线电或电视接收造成了有害干扰(可通过关闭和打 开设备电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电噪 声发射 B 级限制。 此 B 级数字设备符合加拿大 ICES-003 的要求。 中国制造 iii
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。 显示器内部有危险高压,可能导致严重人身伤 害。 • 电源发生故障时,不要尝试自行修复。 请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。 如 有任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。 不要堵塞这些开口。 除非 通风良好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。 如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 请勿使电源板或延长线过载。 过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。 不要将显示器放置在可能受潮的任何区域 中。 将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。 这样做可以防 止因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的
警告 • 对于 I 类设备,必需使用有保护接地的电源插头和良好接地的电网连接, 在建筑物中安装时,请确认配电系统能满足设备的额定电压。 • 为防止火灾或爆炸,不要把显示器暴露在雨中或潮湿环境,显示器内存 在危险的高压,不要打开显示器外壳,如需维修应找专业维修人员。 • 不遵循用户说明书规定而执行的任何变更、调整,有可能导致电击、电 气或机械危险。 • 不要将显示器放置在不稳的推车、平台、三脚架、支架或桌子上。如果 显示器掉落,可能会造成人员伤害并导致本产品严重损坏。仅使用制造 商推荐的安装附件,并按照制造商的指导说明安装产品。 • 在后壳的上部及下部可能有许多狭长的开孔是通风使用的。为保证显示 器持续工作而不过热,这些散热孔不能被堵塞或覆盖。显示器不能置于 床、沙发、毛毯或类似的表面上,也不能靠近于辐射体或热源之上。除 非通风得到保障,否则不能放在书柜或箱子内。 • 切勿将任何异物塞入显示器后壳开孔内。否则,可能会损坏电路部件而 引起火灾或电击。切勿使液体溅落到显示器上。 电池使用注意事项(适用于带电池或纽扣电池的型号) • 用错误型号的电池组更换,可能使安全防护失效,会有着火或爆炸
使用环境 (工作时) 工作时 0°C ~ 40°C 湿度 工作时 10% ~ 85%(非凝露) 海拔高度 工作时 0 ~ 5000 m (0 ~ 16404 英尺) 温度 vii
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。 采用正确的 提起方式放置显示器。 提起或搬运显示器时,抓住显示器的边缘。 不 要通过底座或线缆提起显示屏。 • 清洁。 关闭显示器电源并拔掉电源线。 使用不含麻且非研磨性的布清 洁显示器表面。 将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。 使用液晶专用清洁剂。 切勿直接 将清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。 关闭电源开关, 然后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理。 不要自行修理屏幕! 本指南中使用的约定 警告: 这些信息旨在防止您在试图完成一项任务时受伤。 小心: 这些信息旨在防止当试图完成一项任务时损坏组件。 重要:
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息, 网址是 http://www.asus.com 2. 可选文档 您的经销商可能在您的产品包装中添加了可选文档。 这些文档不是标 准产品包装的组成部分。 中国产品回收服务 若您有不再使用的华硕产品,可将其送至「华硕直营服务维修中心」进行免 费回收,我们将委托符合当地法令及环保要求的第三方机构,确保您的产品 受到妥善的电子废弃物回收处理。 详细直营服务维修中心信息请参考 CSR 官网 : http://csr.asus.com/chinese/article.
1.1 欢迎使用! 感谢您购买 ASUS® 液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.
1.3 组装显示器 要组装显示器: 1. 将显示屏平放在桌布上,然后将底座装到支撑臂上,并用螺钉固定。 您可以轻松地用手指拧紧螺丝。 2.
1.4 连接线缆 1.4.1 液晶显示器后部 7 HDMI 1 2 DVI VGA 3 HDMI 1 6 2 2 5 VGA VP228HE 4 5 VP228T VP228TE VGA 3 4 DVI 1 VP228QG 4 DVI 1 5 VGA HDMI 1 VP228H 4 3 5 VGA 4 VGA 1 1. 交流电源输入端口 2. HDMI 端口 3. DVI 端口 4. VGA 端口 5. 音频输入端口 6. DisplayPort 7.
1.5 显示器简介 1.5.1 使用控制按钮 使用显示器背面的控制按钮调整图像设置。 VP228H/VP228HE/VP228QG 7 6 5 4 3 2 1 VP228T/VP228TE/VP228N/VP228NE /VP228DE Auto 8 1. 电源指示灯: • 下表介绍电源指示灯的颜色定义。 • 2.
3. MENU(菜单)按钮: • 4. 关闭按钮 • 退出OSD菜单。 • 使用此热键从 VGA、DVI、HDMI(只用于 VP228H/VP228HE/ VP228QG)、DisplayPort(只用于 VP228QG)输入信号中进行切换。 5. 输入选择按钮: 6. 快捷键1 • 7. 这是快捷键。 默认设置为亮度。 快捷键2 • 8.
2.1 卸下支撑臂/底座(VESA 壁挂安装时) 此显示器的可拆卸底座是专为 VESA 壁挂安装而设计的。 卸下支撑臂 / 底座 1. 拔掉电源线和信号线。 小心地将显示器正面朝下放在整洁的桌子上。 2. 用手指拧松基座底部的螺钉,并将基座从底座上拆下。然后,用手指 从显示器本体上拆下铰链盖。 3.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 Splendid ASUS VP228 标准模式 VGA 1920x1080@60Hz 风景模式 标准模式 剧场模式 游戏模式 夜晚模式 sRGB模式 读取模式 暗房模式 1. 按菜单按钮显示 OSD 菜单。 2. 按和按钮切换菜单中的选项。 在从一个图标移到另一个图标时, 选项名称高亮显示。 3. 如要选择菜单中高亮显示的项目,请按 按钮。 4. 按和按钮选择所需的参数。 5. 按 按钮进入滑动条,然后使用或按钮(视菜单中的指示器而 定)进行更改。 6.
3.1.2 1.
2.
3.
4.
5. • 聚焦: 通过分别调整(相位)和(时序)来减少图像的横线噪点和竖线噪 点。 调整范围是 0 到 100(仅限 VGA 输入)。 • 自动调谐: 自动将图像调整至最佳位置、时序和相位。 (仅限 VGA 输 入。) • 4:3 仅在输入源为4:3 格式时可用。OverScan 只用于 HDMI 输入源 • 相位调整像素时序信号的相位。 相位调整不当时,屏幕上显示水平干扰。 • 时序(像素频率)控制一次水平扫描所扫描的像素数目。 频率不正确时,屏幕 上显示竖条,图像不成比例。 声音 根据您的喜好调整声音设置(仅限 VP228QG)。 声音 ASUS VP228 标准模式 VGA 1920x1080@60Hz 音量 静音 来源 6.
Input Select ASUS VP228 标准模式 VGA 1920x1080@60Hz VGA DVI HDMI DisplayPort 7.
ASUS VP228 标准模式 VGA 1920x1080@60Hz 系统 返回 显示信息 电源指示灯 电源键锁 恢复出厂模式 • Splendid Demo Mode: 激活 Splendid 功能的演示模式。 • 音量: 调整输出音量大小。(仅限VP228H/VP228HE/VP228T/VP228TE) • GamePlus: GamePlus功能提供一个工具包,可使用户在玩不同类型的 游戏时建立更好的游戏环境。 特别是,瞄准点功能专为喜欢第一人称射击 (FPS)类游戏的新游戏玩家或初玩者而设计。 激活GamePlus: • 选择启用进入GamePlus主菜单。 • 按 和 选择Crosshair (十字瞄准线)和定时器、FPS Counter (计 数器)(仅限VP228QG)和显示对齐(仅限VP228QG)功能。 • 按 确认您选择的功能。 按 GamePlus 主菜单 返回。 按 离开和退出。 GamePlus- 十字线 GamePlus FPS Crosshair Timer FPS Counter Display Alignment (Practice
• QuickFit: 包括三个图案: (1)网格图案 (2)照片尺寸。 1. 网格图案: 可帮助设计人员和用户组织页面内容和布局,以 达到连贯的外观。 Alignment Grid 1 2.
8.
3.2规格 型号 VP228QG VP228H VP228T VP228N 21.5”W (54.6 cm) 面板尺寸 最大分辨率 1920x1080 亮度(典型) 250cd/m2 1000:1 固有对比度(典型) 视角 (CR>10) 170°(H) /160°(V) 显示颜色数 16.7 M(6bit+FRC) 1ms 响应时间 卫星扬声器 1.5W x 2 立体声 来自 HDMI 的声音 是 无 HDMI 输入 是 无 DVI 输入 无 是 D-Sub 输入 是 音频线路输入 DisplayPort 开机功耗 注 是 无 是 无 < 16 W* *基于Energy Star 7.0标准 *当产品无任何外接电源相连时处于零能耗状态 机壳颜色 黑色 省电模式 < 0.5W 关机模式 < 0.5W 倾斜 VESA 壁挂 无 -5° ~ +20° 是 (100mm x 100mm) 物理 含底座尺寸 (WxHxD) 513mm x 373mm x 199.
型号 VP228TE VP228NE 21.5”W (54.6 cm) 面板尺寸 最大分辨率 1920x1080 亮度(典型) 200cd/m2 600:1 固有对比度(典型) 视角 (CR>10) 90°(H) /65°(V) 16.7 M(6bit+FRC) 显示颜色数 1ms 响应时间 卫星扬声器 无 无 HDMI 输入 无 DVI 输入 是 D-Sub 输入 开机功耗 注 无 是 是 无 < 16 W* *基于Energy Star 7.0标准 *当产品无任何外接电源相连时处于零能耗状态 机壳颜色 黑色 省电模式 < 0.5W 关机模式 < 0.5W 倾斜 VESA 壁挂 -5° ~ +20° 是 (100mm x 100mm) 物理 含底座尺寸 (WxHxD) 513mm x 373mm x 199.4mm 物理 不含底座尺寸 (WxHxD) (针对 VESA 壁挂架) 513mm x 309mm x 52.1mm 包装尺寸 (WxHxD) 565x440x123 mm 净重 (Esti.) 3.
型号 面板尺寸 VP228HE 21.5”W (54.6 cm) 最大分辨率 1920x1080 亮度(典型) 200cd/m2 固有对比度(典型) 视角 (CR>10) 显示颜色数 响应时间 卫星扬声器 600:1 90°(H) /65°(V) 16.7 M(6bit+FRC) 1ms 1.5W x 2 立体声 来自 HDMI 的声音 是 HDMI 输入 是 DVI 输入 无 D-Sub 输入 是 音频线路输入 是 开机功耗 注 < 16 W* *基于Energy Star 7.0标准 *当产品无任何外接电源相连时处于零能耗状态 机壳颜色 黑色 省电模式 < 0.5W 关机模式 倾斜 VESA 壁挂 < 0.5W -5° ~ +20° 是 (100mm x 100mm) 物理 含底座尺寸 (WxHxD) 513mm x 373mm x 199.4mm 物理 不含底座尺寸 (WxHxD) (针对 VESA 壁挂架) 513mm x 309mm x 52.1mm 包装尺寸 (WxHxD) 565x440x123 mm 净重 (Esti.) 3.
3.
3.4 支持的时序列表 PC支持的主时序 分辨率 刷新率 水平频率 640x480 60Hz 31.469kHz 640x480 72Hz 37.861kHz 640x480 75Hz 37.5kHz 800x600 56Hz 35.156kHz 800x600 60Hz 37.879kHz 800x600 72Hz 48.077kHz 800x600 75Hz 46.875kHz 1024x768 60Hz 48.363kHz 1024x768 70Hz 56.476kHz 1024x768 75Hz 60.023kHz 1152x864 75Hz 67.5kHz 1280x960 60Hz 60kHz 1280x1024 1280x1024 1440x900 1440x900 1680x1050 1920x1080 1920x1080(仅限 VP228QG) 60Hz 75Hz 60Hz 75Hz 60Hz 60Hz 60Hz 63.981kHz 79.976kHz 55.935kHz 70.635kHz 65.
1920x1080 60Hz 66.587kHz SD/HD时序(仅限HDMI输入) 支持HDMI 1.3、CEA-861B格式、SD/HD的主时序(仅限HDMI输入) 分辨率 刷新率 水平频率 640x480P 720x480P 720x576P 1280x720P 1280x720P 1920x1080i 1920x1080i 59.94 / 60Hz 59.94 / 60Hz 50Hz 50Hz 59.94 / 60Hz 50Hz 59.94 / 60Hz 31.469 / 31.5kHz 31.469 / 31.5kHz 31.25kHz 37.5kHz 44.955 / 45kHz 28.125kHz 33.716 / 33.75kHz 支持HDMI 1.3、CEA-861B格式、SD/HD的可选时序(仅限HDMI输入) 分辨率 刷新率 1440x480P 1440x576P 1920x1080P 1920x1080P 59.94 / 60Hz 50Hz 50Hz 59.94 / 60Hz 水平频率 31.469 / 31.5kHz 31.25kHz 56.