VP247 系列 液晶显示器 用户指南
第一版 2016 年 3 月 版权所有©2016 ASUSTeK COMPUTER INC. 保留所有权利。 未经ASUSTeK COMPUTER INC.
目录 目录 ......................................................................................................... iii 声明 ......................................................................................................... iv 安全信息 ....................................................................................................... vi 保养和清洁 ................................................................................................... vii 中国产品回收服务 .................................................
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。这些限 制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、使用并且辐射 无线电波,如果不按照制造商的说明进行安装和使用,可能会对无线电通讯产生有 害干扰。但是,不能保证在特定安装条件下不会出现干扰。如果本设备确实对无线 电或电视接收造成了有害干扰(可通过关闭和打开设备电源来确定),建议用户采 取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 需要使用屏蔽线连接显示器和图形卡以确保符合 FCC 规定。未经负责标准遵守 的责任方明确准许的变更或改造可能会使用户失去操作本设备的权利。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例
A third-party certification according to ISO 14024 Toward sustainable IT products Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories. Harmful substances are used both in products and their manufacture. Products can often have a short lifespan because of poor ergonomics, low quality and when they are not able to be repaired or upgraded. This product is a better choice.
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,请勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身伤害。 • 电源发生故障时,请勿尝试自行修复。请与专业技术服务人士或经销商联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。如有任何损 坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。请勿堵塞这些开口。除非通风良好, 否则请勿将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源类型,请与 经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 请勿使电源板或延长线过载。过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。请勿将显示器放置在可能受潮的任何区域中。将显 示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以防止因电压 突变而损坏显示器。 • 请勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为确保
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的提起方 式放置显示器。提起或搬运显示器时,抓住显示器的边缘。请勿通过底座或线缆 提起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁显示器表 面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 请勿使用包含酒精或丙酮的清洁剂。使用显示器专用清洁剂。请勿直接将清洁剂 喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的图案桌面有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。屏幕会慢 慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系进行修 理。请勿自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵循这些信息。 注:这些提示和附加信息旨在帮助您完成一项任务。 vii
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com。 2. 可选文档 您的经销商可能在您的产品包装中添加了可选文档。这些文档不是标准产品包 装的组成部分。 中国产品回收服务 若您有不再使用的华硕产品,可将其送至「华硕直营服务维修中心」进行免费回 收,我们将委托符合当地法令及环保要求的第三方机构,确保您的产品受到妥善的 电子废弃物回收处理。 详细直营服务维修中心信息请参考CSR官网: http://csr.asus.com/chinese/article.
ix
x
1.1 欢迎使用! 感谢您购买 ASUS® 液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更宽、更亮、更清晰的显示 屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.
1.3 显示器简介 1.3.1 前部概览 Auto VP247H/VP247HA 7 6 5 VP247T/VP247TA VP247N/VP247NA 4 3 2 1 Auto 8 电源按钮/电源指示灯 1.
菜单按钮: 2. • • 进入 OSD 菜单。 关闭按钮: 3. • 在 OSD 关闭时,按此按钮可显示 OSD 菜单。 • 退出 OSD 菜单。 • 长按 5 秒钟即可开启和关闭按键锁功能。 • 在 OSD 关闭时,按此按钮可显示 OSD 菜单。 • 选择可用的输入源。 输入选择按钮: 4. QuickFit 按钮: 5. • 在 OSD 关闭时,按此按钮可显示 OSD 菜单。 • 此热键可激活专为对齐而设计的 QuickFit 功能。 • QuickFit 功能包含常见的网格状线、纸张尺寸和照片尺寸的页面。(请参 阅1.3.3 QuickFit 功能)。 快捷方式 6. • 在 OSD 关闭时,按此按钮可显示 OSD 菜单。 • 默认:亮度热键 • 要更改热键功能,请转到快捷方式 > 快捷方式 1 菜单。 快捷方式 7. 8.
1.3.2 后部概览 VP247HA 1 2 3 5 6 4 5 6 4 5 6 4 5 VP247H 1 2 3 VP247T/VP247TA 1 2 VP247N/VP247NA 1 1-4 2 1. Kensington 锁槽。 2. 交流电源输入接口。此端口连接电源线。 3. HDMI 端口。此端口用于连接 HDMI 兼容设备。 4. DVI 端口。此 24 针端口适用于 PC(个人电脑)DVI-D 数字信号连接。 5. VGA 端口。此 15 针端口适用于 PC VGA 连接。 6.
1.3.3 QuickFit 功能 QuickFIt 功能包含 3 种模式:(1) 网格状线 (2) 纸张尺寸 (3) 照片尺寸。要激活模 式,按 QuickFit 按钮。再次按该按钮,直至选定所需模式。按照屏幕说明按下按钮 可选择所需模式。 以下部分模式可能无法启用。 请参见显示器上显示的实际模式。 1. 网格状线 网格状线可方便用户有效地组织和比较不同的内容,如电子表格查看和照片编辑。 对齐网格 1 对齐网格 2 Alignment Grid 2 Alignment Grid 1 2.
3.
ASUS VP247 系列液晶显示器 1-7
1-8 第 1 章:产品介绍
2.1 安装显示器支撑臂/底座 安装显示器底座: 1. 将显示器正面朝下放在桌台上。 2. 将底座装到支撑臂上,确保支撑臂上的弹片进入底座上的凹槽。 3. 通过拧紧附带的螺丝,将底座固定到支撑臂上。 我们建议您在桌面上铺上软布,以免损坏显示器。 2.
2.3 连接线缆 请按照下列所述连接线缆: • 连接电源线:将电源线的一端牢固插入显示器上的交流输入接口,将另一端插 入电源插座。 • 连接 VGA/DVI/HDMI 线: • a. 将 VGA/DVI/HDMI 线的一端连接到显示器的 VGA/DVI/HDMI 插孔。 b. 将 VGA/DVI/HDMI 线的另一端连接到计算机的 VGA/DVI/HDMI 插孔。 c. 拧紧两颗螺丝以紧固 VGA/DVI 接头。 连接音频线:将音频线的一端连接到显示器的音频输入端口,而另一端连接到计 算机的音频输出端口。 连接好线缆后,您就可以从 OSD 菜单的“输入选择”项目中选择想要的信号。 2.
ASUS VP247 系列液晶显示器 2-3
2-4 第 2 章:设置
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 Splendid 标准模式 ASUS VP247 VGA 1920 x 1080 @ 60Hz 风景模式 标准模式 剧场模式 游戏模式 夜晚模式 sRGB模式 阅读模式 暗房模式 1. 按下任何按钮(电源按钮除外)可显示 OSD 菜单。 2. 按下 3. 按照屏幕说明按下按钮可在功能中导航。 选取所需功能并按下 可激活它。 如所选功能具有子菜单,请再次按下 和 在子菜单功能中导航。 选取所 需子菜单功能并按下 可激活它。 4. 按下 5.
3.1.2 1.
滤蓝光 2. 在此功能中,您可调整滤蓝光级别。 滤蓝光 标准模式 ASUS VP247 VGA 1920 x 1080 @ 60Hz 0级 1级 2级 3级 4级 • 0 级:无更改。 • 1~4 级:级别越高,蓝光散射越少。 当滤蓝光被激活后,标准模式的默认设置将自动导入。1 级至 3 级之间, 亮度功能用户可配置。4 级是优化的设置。它符合 TUV 低蓝光认证。 亮度功能用户不可配置。 色彩 3.
图像 4.
输入选择 5. 在此功能中,您可以选择想要的输入源。 输入选择 标准模式 ASUS VP247 VGA 1920 x 1080 @ 60Hz 标准模式 ASUS VP247 VGA 1920 x 1080 @ 60Hz VGA DVI H D MI 系统 6. 用于调整系统。 系统 S p le n d id D e m o M o d e 音量 G a m e P lu s ECO Mode 菜单设置 语言 按键锁 更多 • Splendid Demo Mode:将屏幕拆分成两个画面,以进行 Splendid 模式比 较。(仅限风景模式) • 音量:调整范围为 0 到 100。 • GamePlus:GamePlus 功能提供了一个工具包,并为用户在进行不同类 型的游戏时创建一个更好的游戏环境。此外,十字瞄准线功能是专为“第 一人称射击”(FPS) 游戏的新玩家或新手设计的。若要激活此功能: 1. 选择“启用”可进入 GamePlus 主菜单。 2. 按 3.
GamePlus — 十字瞄准线 GamePlus — 定时器 GamePlus — 定时器 — 位置 • ECO Mode:减少能耗。 • 菜单设置: • 3-6 GamePlus 主菜单 * 在 10 到 120 秒之间调整菜单时间。 * 启用或禁用 DDC/CI 功能。 * 调整 OSD 的背景,从不透明到透明。 语言:共有 21 种语言供您选择,分别是:英文、法文、德文、意大利文、 西班牙文、荷兰文、葡萄牙文、俄文、捷克文、克罗地亚文、波兰文、 罗马尼亚文、匈牙利文、土耳其文、简体中文、繁体中文、日文、韩文、 泰文、印度尼西亚文、波斯文。 • :禁用所有功能键。按住右边数来第二个按钮 5 秒可取消按键锁 按键锁: 功能。 • 显示信息:显示关于显示器的信息。 • 电源指示灯:使电源 LED 指示灯点亮/熄灭。 • 电源键锁:启用或禁用电源键。 • 恢复出厂模式:“是”让您恢复默认设置。 第 3 章: OSD (屏幕显示)菜单
快捷方式 7.
3.2 规格摘要 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平/垂直)CR>10 显示颜色 响应时间 SplendidPlus 视频增强技术 SplendidPlus 选择 自动调谐 色温选择 模拟输入 数字输入 耳机插孔 音频输入 扬声器(内置) USB 2.0 端口 颜色 电源 LED 倾斜 枢轴 旋转 高度调整 防盗锁 交流输入电压 功耗 温度(运行时) 温度(非操作时) 尺寸(宽 x 高 x 厚) 重量(约) 多语言 附件 3-8 TFT LCD 23.6" (16:9, 59.94 cm) 宽屏 1920 x 1080 0.2715 mm 250 cd/m2 3000:1 100,000,000:1(ASCR 开启时) 178˚/178˚ 16.7 M < 5 ms 是 8 种视频预设模式 是 4 种色温 D-sub DVI-D,配备 HDCP (VP247H/VP247T/VP247TA/VP247N/ VP247NA) HDMI v1.
机构认证 UL/cUL、CB、CE、ErP、FCC、CCC、CU、RCM、BSMI、 VCCI、PSB、RoHS、J-MOSS、MEPS、WEEE、TCO、 PSE、Windows 7、8.
3.
3.4 支持的运行模式 PC 支持的主时序 分辨率 刷新率 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1152x864 1280x960 1280x1024 1280x1024 1440x900 1440x900 1680x1050 1920x1080 水平频率 60Hz 72Hz 75Hz 56Hz 60Hz 72Hz 75Hz 60Hz 70Hz 75Hz 75Hz 60Hz 60Hz 75Hz 60Hz 75Hz 60Hz 60Hz 31.469kHz 37.861kHz 37.5kHz 35.156kHz 37.879kHz 48.077kHz 46.875kHz 48.363kHz 54.476kHz 60.023kHz 67.5kHz 60kHz 63.98kHz 79.976kHz 55.935kHz 70.635kHz 65.29kHz 67.
VESA 模式,用户可用时序 分辨率 刷新率 848x480 1280x720 (RB) 1280x720 1280x720 1280x768 (RB) 1280x800 (RB) 1280x800 1280x800 1366x768 1440x900 (RB) 1440x900 1680x1050 (RB) 1920x1080 水平频率 60Hz 60Hz 60Hz 75Hz 60Hz 60Hz 60Hz 75Hz 60Hz 60Hz 75Hz 60Hz 60Hz 31.02kHz 44.444kHz 44.772kHz 56.456kHz 47.396kHz 49.306kHz 49.702kHz 62.795kHz 47.712kHz 55.469kHz 70.635kHz 64.674kHz 66.587kHz SD/HD 时序(仅适用于 HDMI 输入) HDMI 1.
ASUS VP247 系列液晶显示器 3-13
3-14 第 3 章: OSD (屏幕显示)菜单