VP32A系列 液晶显示器 用户指南
第一版 2020 年 4 月 版权所有 © 2020 ASUSTeK COMPUTER INC. 保留所有权利。 除了购买者出于备份目的而保留的文档外,未经 ASUSTeK COMPUTER INC.
目录 Notices ......................................................................................................... iv 安全信息 ........................................................................................................ v 保养和清洁 .................................................................................................... vi 回收服务 ...................................................................................................... vii 1.1 欢迎使用!................................................
声明 联邦通信委员会声明 本设备符合 )&& 规则第 部分的要求。其操作符合以下两项条件: 此设备不会产生有害干扰,并且 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 )&& 规则第 部分中关于 % 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、 使用并且辐射无线电波,如果不按照说明进行安装和使用,可能会对无线电 通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干扰。如果 本设备对无线电或电视接收造成了有害干扰(可通过关闭和打开设备电源来 确定),建议用户采取以下一项或多项措施来消除干扰: 调节接收天线的方向或位置。 增大设备与接收器之间的距离。 将此设备和接收设备连接到不同电路的电源插座上。 向代理商或有经验的无线电 电视技术人员咨询以获得帮助。 需要使用屏蔽线连接显示器和图形卡以确保符合 )&& 规定未经负责标 准遵守的责任方明确准许的变更或改造可能会使用户失去操作本设备的 权利。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数
安全信息 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 为防止火灾或电击危险,严禁使本显示器遭受雨淋或受潮。 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身伤 害。 电源发生故障时,不要尝试自行修复。请与专业技术服务人士或经销商 联系。 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。 如 有任何损坏,请立即与经销商联系。 机壳后部和顶部的槽和开口用于通风目的。不要堵塞这些开口。除非通 风良好,否则不要将本产品放置在散热器或热源上部或附近。 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 使用符合您当地电力标准的合适电源插头。 不要使电源板或延长线过载。过载可能导致火灾或电击。 避免灰尘、潮湿和极端温度。不要将显示器放置在可能受潮的任何区域 中。将显示器放置在平稳的表面上。 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以防 止因电压突变而损坏显示器。 严禁将任何异物塞入或使任何液体溅入显示器机壳上的开口内。
保养和清洁 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。 采用正确的 提起方式放置显示器。 提起或搬运显示器时,抓住显示器的边缘。 不 要试图通过底座或线缆提起显示屏。 清洁。 关闭显示器电源并拔掉电源线。 使用不含麻且非研磨性的布清 洁显示器表面。 将布在中性清洁剂中蘸湿后擦去顽固污渍。 不要使用包含酒精或丙酮的清洁剂。 使用液晶专用清洁剂。 严禁直接 将清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。 关闭电源开关, 然后重新打开,确认闪烁已消失。 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理。 不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止您在试图完成一项任务时损坏组件。 重要
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 $686 全球网站提供关于 $686 硬件和软件产品的更新信息,网址是 http://www.asus.com 2.
1.1 欢迎使用! 感谢您购买 $686 液晶显示器! 这是 $686 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,本显示器为您提供更方便愉快的视觉体验! 1.
1.3 组装显示器底座 将显示器正面朝下放在桌子上。 将底座装到支撑臂上。 顺时针转动螺丝以固定底座。然后将显示器调整到最适合观看的角度。 4.
1.4 连接线缆 1.4.1 液晶显示器后部 +'0, 3RZHU $& 端口 'LVSOD\3RUW 端口 +'0, 端口 耳机 端口 第 章: 产品介绍
1.5 显示器简介 1.5.
2.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 ASUS VP32AQ HDR OFF Splendid 标准模式 HDMI 2560X1440 @75Hz 㛅₄㣟ⷍ sRGB㣟ⷍ 枌㔭㣟ⷍ ℥◸㣟ⷍ 㳶ネ㣟ⷍ ⟚㔘㣟ⷍ 擃媹㣟ⷍ 㕕ヽ㣟ⷍ 1. 按 Menu(菜单)按钮显示 OSD 菜单。 2. 和 按钮在菜单中的选项之间切换。 当您从一个图标移动到另 按 一个图标时,选项名称会被高亮显示。 3. 要选择菜单上高亮显示的项目,按 4. 按 5. 按 按钮进入滑动条,然后按照菜单上的指示灯,使用 进行更改。 6.
3.1.2 1.
2. 滤蓝光 在此功能中,您可以调整设置,更好地保护您的眼睛。.
•休息提醒:根据您设定的工作时间,提供休息提醒。例如,如果你设置 30-工作时间为30分钟,时间到时,显示器左上角会弹出5秒的提示。按任 意键使提醒OSD消失。 当开启此功能时,以下功能不可用:Splendid Demo Mode、GamePlus、QuickFit。 3.
4. 图像 您可以从这个主要功能调整图像的清晰度、Trace Free、画面控 制、VividPixel、ASCR、FreeSync(仅限HDMI接 口)、HDR。 ▼ᾍ ASUS VP32AQ HDR OFF 标准模式 HDMI 2560X1440 @75Hz 㳃㔮ⵤ Trace Free 䏹映㉥ VividPixel ASCR FreeSync HDR • 清晰度:调整图片清晰度。调整范围是0到100。 • Trace Free:使用驱动加速技术加快响应时间。调整范围是慢 0 到快 100。 • 画面控制:调整画面比例到“全屏幕”、“4:3” 或“OverScan”。 • • 4:3 仅适用于输入源为 4:3 格式时。 OverScan仅适用于HDMI输入。 • VividPixel:ASUS 独家技术,带来栩栩如生的视觉效果,水晶 般清晰,注重细节享受。调整范围是 0 到 100。 • ASCR:选择启用或关闭以启用或关闭动态对比功能。 • FreeSync(仅限HDMI接口):选择启用或关闭以启用或关闭通 过HDMI串流1.
5. 输入选择 选择输入源。 ASUS VP32AQ HDR OFF 幑‣廇ㆧ 标准模式 HDMI 2560X1440 @75Hz HDMI Dispiay Port 6.
ASUS VP32AQ HDR OFF 䮹䶝 标准模式 HDMI 2560X1440 @75Hz 庒▜ 㓼䟸ẟ⼭ 䏳㵎㇅䟸㼭 䏳㵎揬掿 ⼠⟋₸≀㣟ⷍ (页码 2/2) 3-8 • • Splendid Demo Mode:激活 Splendid 功能的演示模式。 声音:调节范围为0 - 100。 • • QuickFit: 参考3.1.2.
7.
3.1.2.1 GamePlus 功能 GamePlus 功能提供一个工具套件并为用户打造了一个玩不同类型游戏时 的更好游戏环境。十字瞄准线叠加了六种不同的十字瞄准线选项,您可以 选择一个最符合您游戏需求的选项。 屏幕上的计时器可放置在画面左侧, 以统计已消耗的游戏时间。FPS(每秒帧数)计数器会告知您游戏运行的 顺畅程度。 Display Alignment(显示对齐)在屏幕的4侧显示对齐线,这是 一种轻松便捷的工具,可让您完美地对齐多台显示器。 要激活 GamePlus: 1. 按 Menu(菜单)按钮显示 OSD 菜单。 2. 3. 4. 5.
3.1.2.2 QuickFit 功能 QuickFit 功能包含三种图案:(1) 网格 (2) 纸张尺寸 (3) 照片尺寸。 1. 网格图案:可帮助设计人员和用户组织页面内容和布局,以达到连贯 的外观效果。 Alignment Grid 1 2. Alignment Grid 2 纸张尺寸:让用户在屏幕上观看实际尺寸的文档。 B5 Letter Letter B5 EXIT 3.
3.2 规格 型号 面板尺寸 最大分辨率 亮度(典型) 固有对比度(典型) 31.5"W(80cm) 2560X1440@75Hz 350cd/m2 1000:1 视角(CR>10) 178°(H) /178°(V) 显示颜色数 1.07B 响应时间 5ms(灰色到灰色) VGA 输入 否 HDMI 输入 是 HDMI 2输入 否 DisplayPort 是 音频线路输出 是 开机功耗 <25w (测量200尼特屏幕亮度,不连接音频/USB/读卡器) 机壳颜色 黑色 省电模式 < 0.5W 关机模式 < 0.3W 倾斜 -5° ~ +8° 壁挂 是 (100mm x 100mm) 物理含底座尺寸 (WxHxD) 715mmx 424mmx 50mm 物理不含底座尺寸 (WxHxD) (针对壁挂架) 包装尺寸 (WxHxD) 净重(约) 毛重(约) 额定电压 温度(运行时) 3-12 VP32A 715mm x 492mm x 202mm 799mm x 526mm x140mm 7.9kg 9.
3.3 故障排除(常见问题) 问题 电源LED不亮 可能的解决办法 • 按 按钮,检查显示器是否打开。 • 检查适配器和电源线是否正确连接到显示器和电源 插座。 • 检查 OSD 菜单中的电源指示灯功能。 选择“启用” 以打开电源 LED 指示灯。 电源LED显示黄色,屏幕上不显 示任何图像 • 检查显示器和计算机是否打开。 • 确保信号线正确连接到显示器和计算机。 • 检查信号线,确保没有插针弯曲。 • 将计算机连接到一台工作正常的显示器,检查计算机 是否工作正常。 屏幕图像太亮或太暗 • 通过OSD调整对比度和亮度设置。 屏幕图像跳动或图像中出现波纹 图案 • 确保信号线正确连接到显示器和计算机。 • 移开可能导致电子干扰的电子设备。 屏幕图像颜色不正确(白色看起来 • 检查信号线,确保没有插针弯曲。 不是白色) • 通过OSD执行重置。 • 通过 OSD 选择适当的色温(色温)。 没有声音或声音太低 • 调整显示器或计算机的音量设置。 • 确保已正确安装并启用计算机声卡驱动程序。 3.
3-14 第 3 章: 一般说明