VS197/VS198 系列 LCD 显示器 用户指南
目录 声明 iii 安全信息 ........................................................................................................iv 保养和清洁 ......................................................................................................v 1.1 欢迎使用 ......................................................................................... 1-1 1.2 物品清单 ......................................................................................... 1-1 1.3 组装显示器底座 .......................................................
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰。 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的 干扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、 使用并且辐射无线电波,如果不按照制造商的说明进行安装和使用,可能会 对无线电通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干 扰。如果本设备对无线电或电视接收造成了有害干扰(可通过关闭和打开设 备电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 作为 Energy Star® 的合作伙伴,本公司已经确定本产品符合 Energy Star® 在能源效率方面的要求。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电噪 声
安全信息 iv • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身伤 害。 • 电源发生故障时,不要尝试自行修复。请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。如 有任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。不要堵塞这些开口。除非通 风良好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 不要使电源板或延长线过载。过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。不要将显示器放置在可能受潮的任何区域 中。将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以防 止因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的 提起方式放置显示器。提起或搬运显示器时,抓住显示器的边缘。不要 通过底座或线缆提起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁 显示器表面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。使用液晶专用清洁剂。切勿直接将 清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。关闭电源开关, 然后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理。不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵循
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 vi 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com 2.
1.1 欢迎使用 感谢您购买 ASUS® VS197/VS198 系列 LCD 显示器! 这是 ASUS 最新推出的宽屏 LCD 显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,VS197/VS198 系列产品为您提供方便愉快的视觉体验! 1.
1.3 组装显示器底座 组装显示器底座: 1. 将底座连接到显示器支撑臂,然后顺时针转动。听到咔嗒一声时,说 明底座已连接安装。 2. 将显示器调整到最适合观看的角度。 我们建议您在桌面上铺上软布,以免损坏显示器。 2 1 1.4 连接线缆 连接线缆: 根据第 1-5 页 1.5.
1.5 显示器简介 1.5.1 LCD 显示器前部 VS197N/NE/D/DE VS198N/D 1 2 4 5 6 VS197T VS197TE 1 1. 3 4 5 6 按钮: • 长按此按钮 2-4 秒钟可以自动将图像调整至最佳位置、时钟和相 位(仅限 VGA 模式)。 • 利用此热键,可以切换采用 SPLENDID™ 视频增强技术的六种视 频预设模式(风景、标准、剧场、游戏、夜晚、sRGB 等模式)。 • 显示 OSD 菜单时,退出 OSD 菜单或返回上一级菜单。 • 按此按钮可以减小所选功能的值或移动至下一个功能。 • 这也是对比度调整热键。 • 按此按钮可以减小所选功能的值或移动至下一个功能。 • 这也是音量调整热键。 2. 按钮: 3.
4. 菜单按钮: • 按此按钮可以进入 OSD 菜单。 • 显示 OSD 时,按此按钮可以进入/选择高亮显示的图标(功能)。 • 按此按钮可以增加所选功能的值或向右/向上移动至下一个功能。 • 这也是亮度调整热键。 5. 按钮: 6.
1.5.2 LCD 显示器后部 5 1 2 3 4 1. 交流电源输入 2. 音频线路输入端口 (仅限型号 VS197T、VS197TE) 3. DVI-输入(仅限型号 VS197N、VS197NE、VS198N、VS197T、VS1 97TE) 4. VGA-输入 5.
2.1 卸下支撑臂/底座(VESA 壁挂安装时) VS197/VS198 系列 LCD 显示器的可拆卸底座是专为 VESA 壁挂安装而设 计的。 卸下支撑臂 / 底座: 1. 拉止动杆,逆时针转动以解锁。 2. 从显示器上卸下底座。 3. 用手指轻轻取下底座颈部的盖板。使用螺丝刀取下用于将底座固定到 显示器上的四个螺丝。 4.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 VS197 Splendid 风景模式 色彩 标准模式 图像 剧场模式 输入选择 游戏模式 系统 夜晚模式 sRGB Move Menu Exit 1. 按 [Menu]按钮显示 OSD 菜单。 2. 按 和 切换功能。按 [Menu]按钮高亮显示和激活所需的功能。 如果所选的功能有子菜单,再按 和 可以切换子菜单功能。按 [Menu] 按钮高亮显示和激活所需的子菜单功能。 3. 按 和 更改所选功能的设置。 4. 如要退出 OSD 菜单,可以按 其它功能。 3.1.2 1.
• 剧场模式:这是使用 SPLENDID™ 视频增强技术观看影片时的最 佳选择。 • 游戏模式:这是使用 SPLENDID™ 视频增强技术玩游戏时的最佳 选择。 • 夜晚模式:这是使用 SPLENDID™ 视频增强技术玩暗场景游戏或 观看影片时的最佳选择。 • sRGB: 浏览 PC 中的照片和图形时,这是最佳选择。 在标准模式下,用户不能配置饱和度、肤色、清晰度和 ASCR等功能。 在 sRGB 模式下,用户不能配置亮度、对比度、饱和度、色温、肤色、 清晰度和 ASCR 等功能。 2. 色彩 利用此功能选择您喜欢的图像颜色。 VS197 Splendid Brightness Color Contrast Image Saturation Input Select Color Temp.
3. 图像 您可以在此主功能中调整图像清晰度、画面控制、位置(仅限 VGA) 和聚焦(仅限 VGA)。 VS197 Splendid 清晰度 色彩 画面控制 图像 ASCR 输入选择 位置 系统 聚焦 Move 4.
5.
3.2 规格 型号 VS197T/N/D VS197TE/NE/DE 面板尺寸 18.5”W (46.99 cm) 18.5”W (46.99 cm) 1366 x 768 1366 x 768 250cd/m2 200cd/m2 最大分辨率 亮度(典型) 1000:1 600:1 ≧170°(H) / ≧160°(V) ≧90°(H) / ≧50°(V) 固有对比度(典型) 视角 (CR=10) 16.7 M 显示颜色数 5ms 响应时间 DVI 输入 VS197D:无 VS197DE:无 VS197T/N:是 VS197TE/NE:是 D-Sub 输入 是 <13.7W 开机功耗 注 *基于Energy Star 6.0标准 < 0.5W 省电模式 < 0.5W 关机模式 -5°~ +20° 倾斜 VESA 壁挂 是 (75mm x 75mm) 物理尺寸 (WxHxD) 447.1 x 345.7 x 184.9 mm 447.1 x 345.7 x 184.
型号 VS198N/D 面板尺寸 19”W (48.26 cm) 最大分辨率 亮度(典型) 固有对比度(典型) 视角 (CR=10) 显示颜色数 响应时间 DVI 输入 D-Sub 输入 1440 x 900 250cd/m2 1000:1 ≧170°(H) / ≧160°(V) 16.7 M 5ms VS198D:无 VS198N:是 是 开机功耗 符合 Energy Star 5.0 标准 省电模式 < 0.5W 关机模式 倾斜 VESA 壁挂 < 0.5W -5°~ +20° 是 (75mm x 75mm) 物理尺寸 (WxHxD) 446.1 x 368.4 x 184.9 mm 包装尺寸 (WxHxD) 494 x 460 x 114 mm 净重 (Esti.) 毛重 (Esti.) 额定电压 2.7 kg 4.
3.
3.4 支持的时序列表 VESA / IBM 模式支持时序(D-SUB、DVI-D、HDMI 输入) 分辨率 640 x 350 640 x 480 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1366 x 768 VS197 刷新率 70Hz 60Hz 67Hz 72Hz 75Hz 70Hz 56Hz 60Hz 72Hz 75Hz 75Hz 60Hz 70Hz 75Hz 60Hz 水平频率 31.469KHz 31.469KHz 35KHz 37.861KHz 31.469KHz 31.469KHz 35.156KHz 37.879KHz 48.077KHz 46.875KHz 49.725KHz 48.363KHz 56.476KHz 60.023KHz 47.