VS248 系列 LCD 顯示器 使用手冊
E6235 第一版 2011 1月 版權所有© 2011 ASUSTeK華碩電腦公司,保留所有權利。 本手冊沒有任何部分,包括手冊描述的產品和軟體,可未經華碩電腦公司(「華碩」, “ASUS”)之明確書面許可,以任何形式或任何手段複製、傳播、轉錄、儲存於檢索系統,或 翻譯成任何語言,除購買者為保存文件進行之備份外。 若有以下情況,將不提供產品保證或服務,如:(1)產品經修理、修改或更改,除該修理、改 裝係受華碩書面授權外,或(2)產品的序號列遭汙損或遺失。 華碩係「依原狀」提供本手冊,無任何明示或暗示等形式之擔保,包括但不限於暗示性或適銷性 或特定用途的保證。在任何情況下,華碩及其董事、職員、雇員或代理人皆無需承擔任何間接、 特殊、附帶或連帶之損害(包括利潤損失、營業損失、無法使用或遺失資料及商業中斷損失等) ,即使華碩已被告知本手冊或產品之任何缺陷或錯誤造成的損壞,可能會導致此類損失。 本手冊所載之規格及資料,僅供參考,並可不另行通知而隨時更改,且不應理解為華碩之承諾。 華碩不為本手冊可能出現的任何錯誤或不準確,負擔任何責任與義務,包括本手冊所述之產品和 軟體。 本手冊中出現的產品和公司名稱,可能是或可能
目次 注意事項 ............................................................................................iv 安全資訊 .............................................................................................v 保養和清潔 ........................................................................................vi 第 1 章: 產品介紹 1.1 歡迎使用! ...........................................................................1-1 1.2 包裝內容 ..............................................................................1-1 1.3 顯示器介紹 ..
注意事項 聯邦通訊委員會聲明 本裝置符合 FCC 規定之第 15 篇。 操作符合下列兩個條件: • 本裝置不會造成有害干擾,而且 • 本裝置會接受任何接收到的干擾,包括可能會影響裝置運作的干擾。 本設備通過測試並符合 FCC 規定之第 15 篇 B 級數位裝置的限制。 這些限 制的用意在於提供適當防護,避免設備安裝在居住環境下產生有害干擾。 本設備會產生、使用和發射無線電頻能量,此外,若未依照製造商的指示安 裝和使用,可能會對無線電通訊產生不良干擾。 然而,並不保證在特定安 裝情況下不會產生干擾。 若本設備對收音機或電視機的收訊產生不良干擾 (可開啟然後關閉設備電源判定),使用者可透過以下方法消除干擾: • 重新調整接收天線的方向或位置。 • 增加設備和接收天線之間的距離。 • 將本設備連接到與接收器電源不同的電源插座上。 • 請向經銷商或有經驗的廣電技術人員尋求協助。 連接顯示器與顯示卡的遮蔽纜線,須符合 FCC 的規定。 若未經相容性規 定之相關當局明示許可,擅自修改或改裝本裝置,使用者可能喪失操作 本設備之權限。 加拿大通訊部聲明 本數位裝置未超過加拿大通訊部無線電干擾法規所規定
安全資訊 • 設定本顯示器之前,請詳讀產品包裝內的說明文件。 • 為預防起火或觸電,請勿將顯示器置於雨中或潮溼環境中。 • 請勿試圖打開顯示器的機殼。 顯示器內部的高壓電可能造成人員嚴重受 傷。 • 若電源供應器損壞,請勿嘗試自行修復。 請洽詢合格的維修技術人員您 的零售商。 • 使用本產品前,請確定已正確連接所有纜線,而且電源線並未損壞。 若 發現任何損壞,請立刻聯絡您的經銷商。 • 機殼背面或頂端的開口和通風口係用於散熱。 請勿堵塞這些開口。 除 非通風良好,否則請勿將本產品置於靠近散熱器或熱源的位置或其上 方。 • 本顯示器只能在產品標籤所示的電源環境下操作。 若您不確定您家中的 電源規格,請洽詢您的經銷商或當地的電力公司。 • 使用符合當地電源標準的電源插頭。 • 不可使排插和延長線的電源過載。 電源過載會導致起火或人員觸電。 • 避免在多灰塵、潮溼和極端溫度的環境中使用。 請勿將顯示器置於可能 會使其受潮的區域。 請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本機的電源插頭。 如此可預防顯示 器因電源突波而損壞。 • 請勿讓任何物體或
保養和清潔 • 抬高或重新移位顯示器之前,請先拔下纜線和電源線。 顯示器移位前, 請依照正確的抬高方法。 抬高或移動顯示器時,請握住顯示器的邊緣。 請勿以拉抬底座或纜線的方式抬高顯示器。 • 清潔。 關閉顯示器的電源,然後拔下電源線。 使用無毛球且不會刮傷 螢幕的布清潔顯示器表面。 可用沾有中性清潔劑的布清除頑垢。 • 避免使用含有酒精或丙酮的清潔劑。 使用顯示器專用的清潔劑。 請勿 直接將清潔劑噴灑於螢幕上,否則可能滲入顯示器內並造成人員觸電。 若顯示器發生以下情況,屬於正常現象: • 由於螢光燈的特性,初次使用螢幕時,畫面可能會閃爍。 請關閉電源開 關,然後再重新開啟,確定閃爍現象消失。 • 不同的桌面模式可能導致螢幕有輕微亮度不均的情況。 • 顯示同一幅影像數小時後,切換影像時可能會出現前張影像的殘影。 殘 影會慢慢消失,或者您可以開關電源數小時消除此情況。 • 螢幕變黑、閃爍或完全無法運作時,請洽詢您的經銷商或服務中心進行 修復。 請勿自行修理螢幕! 本手冊使用的慣語 警告: 執行作業作時,避免人員受傷的資訊。 注意: 執行作業時,避免零組件損壞的資訊。 重要: 執行作業時
其他詳細資訊來源 如需其他資訊和產品與軟體的更新程式,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供有關 ASUS 硬體和軟體產品的最新資訊。 請連至 http://www.asus.com 取得相關資訊。 2.
viii
1.1 歡迎使用! 感謝您購買 ASUS ® LCD 顯示器! ASUS 最新的 LCD 寬螢幕顯示器提供更清晰、更寬廣和更明亮的畫面,以 及許多可增強觀看感受的功能。 您可藉由這些功能享受到本顯示器帶給您的便利與快樂的視覺體驗! 1.
1.3 顯示器介紹 1.3.1 正面圖 1 1. 2 3 4 5 6 6 按鈕: • 選擇所需的預設模式。 • 離開 OSD 選單,或返回啟用 OSD 選單時的上一個選單。 • 按下此按鈕 2 到 4 秒,自動調整影像至最佳位置、時脈和相位 (僅 限 VGA 模式)。 • 降低設定值或往左/下移動選項。 • 對比快速鍵 2. 3.
4. • 增加設定值或往右/上移動選項。 • 亮度快速鍵 • 選擇可用的輸入來源。 5. 按鈕: 6. 電源按鈕 電源指示燈 • 開啟 • 電源指示燈的顏色定義如下表所示。 1.3.2 關閉顯示器電源。 狀態 說明 藍燈 黃燈 關 開 待機模式 關 背面圖 6 背面接頭 1. AC-IN 連接埠。此連接埠用於連接電源線。 2. HDMI 連接埠。此連接埠用於連接 HDMI 相容裝置。 3. DVI 連接埠。這個 24 針的連接埠用於連接個人電腦的 DVI-D 數位訊 號。 4. VGA 埠。此 15 針連接埠用於連接個人電腦的 VGA 介面。 5. 耳機插孔。此連接埠僅在連接 HDMI 訊號線時可使用。 6.
1-4 第 1 章: 產品介紹
2.1 組裝顯示器支架 底座 組裝螢幕底座: 1. 將顯示器正面朝下置於桌上。 2. 將底座接上支撐臂,確定支撐臂上的固定片插入底座的溝槽內。 3. 旋緊固定螺絲將基座固定於支臂上。 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 2.
2.3 拆開支臂 裝) 底座 (適用於 VESA 壁掛式安 本螢幕可拆卸的支撐臂/底座專為VESA壁掛架所設計。 拆卸支撐臂/底座: 1. 將螢幕正面面向桌面放置。 2. 卸下4個螺絲孔內的橡膠。 (圖 1) 3. 卸下底座 (圖 2)。 4. 將後轉軸蓋撬開 (圖 3)。 5.
2.4 1. 接線 依下列指示連接纜線: • 連接電源線:將電源線的一端牢牢插入螢幕的AC輸入,再將另一端插入 HDMI DVI VGA Earphone jack 電源插座。 • 連接 VGA/HDMI/DVI 訊號線: • a. 將 VGA/DVI/HDMI 訊號線的一端接至顯示器的 VGA/DVI/HDMI 連接埠。 b. 將 VGA/DVI/HDMI 訊號線的另一端連接到電腦的 VGA/DVI/HDMI 連接埠。 c. 鎖緊兩顆螺絲固定 VGA/DVI 接頭。 使用耳機 (僅限連接 HDMI 線時): 將耳機插頭連接顯示器的耳機插孔。 完成接線後,可從 OSD 選單的 [輸入選擇] 項目中選擇所需的訊號。 2.
2-4 第 2 章: 設定
3.1 OSD ( 螢幕功能顯示 ) 選單 3.1.1 如何重新設定 1. 按下 MENU 按鈕啟動 OSD 選單。 2. 和 導覽 按下 各個功能。反白顯示所需功 能,然後按下 MENU 按鈕啟 動該功能。如果所選擇的功能 和 導覽子選單功能。反白顯示 有子選單,請再按一次 所需的子選單功能,然後按下 MENU 按鈕啟動該功能。 3. 按下 4. 若要離開並儲存 OSD 選單,請重複按 按鈕,直到 OSD 選單關 閉為止。若要調整其他功能,請重複步驟 1-3。 3.1.2 1.
2. 色彩 您可以透過此功能表調整亮度、 對比、彩度、色溫及膚色。 • 亮度:調整範圍為 0 到 100。 為啟動此功能的快速 鍵。 • 對比:調整範圍為 0 到 100。 為啟動此功能的快速 鍵。 • 彩度:調整範圍從 0 到 100。 • 色溫:含有冷色溫、正常、暖色溫和使用者模式等四個色溫模式。 • 膚色:含有紅潤色、自然色和黃豔色等三個膚色模式。 • Smart View: 在較大的觀看角度下提供更佳的顯示品質。 在使用者模式中,使用者可設定 R (紅色)、G (綠色) 和 B (藍色) 顏色, 調整範圍介於 0 至 100。 3.
4. 輸入選擇 在此功能中,您可選擇所需的輸 入來源。 5.
3.2 規格總覽 (VS248) 面板類型 面板大小 最大解析度 畫素間距 亮度 (最大) 對比比例 (一般) 對比比例 (最大) 視角 (水平 垂直) CR > 10 顯示色彩 回應時間 SPLENDID™ 影像增強 技術 SPLENDID™ 選項 自動調整 色溫選項 膚色選項 數位輸入 類比輸入 耳機插孔 顏色 電源 LED 傾角 Kensington 鎖 電壓 耗電量 TFT LCD 24 吋 (16:9,61 cm) 寬螢幕 1920 x 1080 0.2768 mm 250 cd/m2 1000:1 50,000,000:1 (ASCR 開啟時) 170˚/160˚ 16.7 M 2 毫秒 是 溫度 (運作時) 0˚C~40˚C 溫度 (未運作時) -20˚C~+60˚C 尺寸 (寬 X 高 X 深) 573 mm x 412 mm x 206 mm (本機) 645 mm x 475 mm x 140 mm (包裝) 4.1 kg (淨重);6.
3.
3.4 支援的操作模式 解析度頻率 水平頻率 (KHz) 垂直頻率 (Hz) 畫素 (MHz) 640x480 640x480 640x480 640x480 720x400 800x600 800x600 800x600 800x600 832x624 1024x768 1024x768 1024x768 1152x864 1280x720 1280x768 1280x800 1280x960 1280x1024 1280x1024 1360x768 1366x768 1440x900 1600x1200 1680x1050 1920x1080 ( 主要 ) 31.5 35.0 37.9 37.5 31.5 35.16 37.9 48.1 46.9 49.7 48.4 56.5 60.0 67.5 45 47.78 49.7 60.0 63.4 79.97 47.71 47.71 55.94 75.0 65.3 60 67 72 75 70 56 60 72 75 75 60 70 75 75 60 60 60 60 60 75 60 60 60 60 60 25.18 30.24 31.