VW22A 系列 液晶显示器 用户指南
第一版 V1 2012年 2 月 版权所有 © 2012 ASUSTeK COMPUTER INC. 保留所有权利。 除了购买者出于备份目的而保留的文档外,未经 ASUSTeK COMPUTER INC.
目录 声明 ...................................................................................................iv 安全信息 .............................................................................................v 保养和清洁 ........................................................................................vi Takeback Services .........................................................................vii 第 1 章: 产品介绍 1.1 欢迎使用! ...........................................................................1-1 1.
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作 的干扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规 定。这些限制旨在为居民区安装提供防止有害干扰的合理保护本设备会产 生、使用并且辐射无线电波,如果不按照制造商的说明进行安装和使用,可 能会对无线电通讯产生有害干扰但是,不能保证在特定安装条件下不会出现 干扰如果本设备确实对无线电或电视接收造成了有害干扰(可通过关闭和打 开设备电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电 / 电视技术人员咨询以获得帮助。 需要使用屏蔽线连接显示器和图形卡以确保符合 FCC 规定未经负责标准 遵守的责任方明确准许的变更或改造可能会使用户失去操作本设备的权 利。 作为 Energy Star® 的合作伙伴,本公司已经确定本
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳显示器内部有危险高压,可能导致严重人身伤害。 • 电源发生故障时,不要尝试自行修复请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏如有 任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的不要堵塞这些开口除非通风良 好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 不要使电源板或延长线过载过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度不要将显示器放置在可能受潮的任何区域中 将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线这样做可以防止 因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为确保正常运行,本显示器
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线采用正确的提 起方式放置显示器提起或搬运显示器时,抓住显示器的边缘不要通过底 座或线缆提起显示屏。 • 清洁关闭显示器电源并拔掉电源线使用不含麻且非研磨性的布清洁显示 器表面将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂使用显示器专用清洁剂切勿直接将清 洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁关闭电源开关,然 后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的图案桌面有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像屏 幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵循这些信息。 注:
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com。 2. 可选文档 您的经销商可能在您的产品包装中添加了可选文档这些文档不是标准 产品包装的组成部分。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.
viii
1.1 欢迎使用! 感谢您购买 ASUS® LCD 显示器! 这是 ASUS 最新推出的宽屏 LCD 显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.
1.3 显示器简介 1.3.1 前部概览 1 1. 2 3 4 5 按钮: • 选择所需的预设模式。 • 显示 OSD 菜单时,退出 OSD 菜单或返回上一级菜单。 • 按住此按钮 2-4 秒钟可以自动将图像调整至最佳位置、时序和相 位(仅限VGA模式)。 • 减小值或者向左 / 向下移动您的选择。 • 激活 QuickFit 功能(请参见 1.3.3 QuickFit 功能)。 2. 3. 菜单按钮: • 打开 OSD 菜单执行所选的 OSD 菜单项目。 • 增大值或者向右 / 向上移动您的选择。 • 亮度热键。 4.
5. 电源按钮 / 电源指示灯 • 打开 / 关闭显示器电源。 • 下表介绍电源指示灯的颜色定义。 1.3.2 状态 描述 蓝色 黄色 关机 开机 待机模式 关机 后部概览 DVI VGA 4 后部接口 1. 音频输入接口。此接口通过随机提供的音频线连接 PC 音频源。 (仅限 VW22AT/VW22AS) 2. 交流电源输入接口。此端口连接电源线。 3. DVI 接口。此 24 针接口用于连接 PC(个人计算机)DVI-D 数字信 号。(仅限 VW22AT/VW22AN) VGA 接口。此15 针端口用于连接 PC VGA。 4.
1.3.
ASUS VW22A 系列 LCD 显示器 1-5
1-6 第 1 章:产品介绍
2.1 安装显示器底座 安装显示器底座: 1. 将显示器正面朝下放在桌台上。 2. 然后取出底座,并且如下图所示,将底座装上显示器,当您听到 “喀”的声响,表示已经将底座卡入至固定处。 我们建议您在桌面上铺上软布,以免损坏显示器。 2.
2.3 卸下支撑臂 / 底座(VESA 壁挂安装时) 此显示器的可拆卸支撑臂/底座是专为 VESA 壁挂安装而设计的。 卸下支撑臂 / 底座: 1. 将显示器正面朝下放在桌台上。 2. 卸下四个螺丝孔中的橡胶塞(如图 1)。 3. 使用十字螺丝起子松开如下图所示的二颗固定螺丝(如图 1),即可向 下卸除包含支撑柱的底座(如图 2)。 螺絲孔上的 塑料保護蓋 二顆螺絲 支撐柱 / 底座 图1 图2 我们建议您在桌面上铺上软布,以免损坏显示器。 2.4 1.
• 连接电源线:将电源线的一端牢固插入显示器上的交流输入,将另一端 插入电源插座。 • 连接 VGA/DVI 线: a. 将 VGA/DVI 线的一端连接到显示器的 VGA/DVI 端口。 b. 将 VGA/DVI 线的另一端连接到计算机的 VGA/DVI 接口。 c. 拧紧两个螺丝以固定 VGA/DVI 接头。 连接好线缆后,您就可以从 OSD 菜单的“输入选择”项目中选择想要的 信号。 2. 完成连接后,请将电源与所有的信号线穿过信号线固定钩做好整理。 信號線固定鉤 2.
2-4 第 2 章:设置
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 1. 按 MENU(菜单)按钮显示 OSD 菜单。 2. 按 ,然后按 切 换功能。高亮显示所需的功 能,然后按 MENU(菜单)按 钮激活该功能。如果所选的功 能有子菜单,再次按 和 切换子菜单功能。高亮显示所需的子菜单功能,然后按 MENU (菜单)按钮激活该功能。 3. 按 4. 如要退出并保存 OSD 菜单,请反复按 按钮,直到 OSD 菜单消 失。如要调整其他功能,请重复步骤 1-3。 3.1.2 1.
2. 色彩 您可以在此菜单中调整亮度、 对比度、饱和度、色温、肤色 和 Smart View。 • 亮度:调整范围是 0 到 100。 是激活此功 能的热键。 • • 对比度:调整范围是 0 到 100。 饱和度:调整范围是 0 到 100。 色温:包含四种颜色模式,分别是:冷色温、常规色、暖色温和 用户模式。 肤色:包含三种颜色模式,分别是红润色、自然色和黄艳色。 • Smart View:在大视角情况下提供更好的显示质量。 • • 在用户模式下,用户可以配置 R(红色)、G(绿色)和 B(蓝色); 调整范围是 0-100。 3.
4. 输入选择 在此功能中,您可以选择想要 的输入源。 5.
3.2 规格摘要(VW22AT) 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 SPLENDID™ 视频增强技术 SPLENDID™ 选择 自动调谐 色温选择 肤色选择 数字输入 模拟输入 音频输入接口 颜色 扬声器(内置) 电源 LED 倾斜 VESA 壁挂安装 防盗锁 额定电压 功耗 温度(运行时) TFT LCD 22"(16:10、55.88 cm)宽屏幕 1680 x 1050 0.282 mm 250 cd/m2 1000:1 50,000,000:1(ASCR 开启时) 170°/160° 16.7 M 5 ms 是 6 种视频预设模式(使用热键) 是(使用热键) 4 种色温 3 种肤色 DVI-D(带 HDCP) D-Sub 3.5 mm 迷你插孔 黑色 1 W x 2 立体声,RMS 蓝色(开机)/ 黄色(待机) +20° ~ -5° 100 x 100 mm 是 交流:100 ~ 240V 开机:< 33 W,待机:< 0.5 W,关机:< 0.
规格摘要(VW22AN) 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 SPLENDID™ 视频增强技术 SPLENDID™ 选择 自动调谐 色温选择 肤色选择 数字输入 模拟输入 颜色 电源 LED 倾斜 VESA 壁挂安装 防盗锁 额定电压 功耗 温度(运行时) TFT LCD 22"(16:10、55.88 cm)宽屏幕 1680 x 1050 0.282 mm 250 cd/m2 1000:1 50,000,000:1(ASCR 开启时) 170°/160° 16.7 M 5 ms 是 6 种视频预设模式(使用热键) 是(使用热键) 4 种色温 3 种肤色 DVI-D(带 HDCP) D-Sub 黑色 蓝色(开机)/ 黄色(待机) +20° ~ -5° 100 x 100 mm 是 交流:100 ~ 240V 开机:< 33 W,待机:< 0.5 W,关机:< 0.
规格摘要(VW22AS) 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 SPLENDID™ 视频增强技术 SPLENDID™ 选择 自动调谐 色温选择 肤色选择 模拟输入 音频输入接口 颜色 扬声器(内置) 电源 LED 倾斜 VESA 壁挂安装 防盗锁 额定电压 功耗 温度(运行时) TFT LCD 22"(16:10、55.88 cm)宽屏幕 1680 x 1050 0.282 mm 250 cd/m2 1000:1 50,000,000:1(ASCR 开启时) 170°/160° 16.7 M 5 ms 是 6 种视频预设模式(使用热键) 是(使用热键) 4 种色温 3 种肤色 D-Sub 3.5 mm 迷你插孔 黑色 1 W x 2 立体声,RMS 蓝色(开机)/ 黄色(待机) +20° ~ -5° 100 x 100 mm 是 交流:100 ~ 240V 开机:< 33 W,待机:< 0.5 W,关机:< 0.
规格摘要(VW22AD) 面板类型 面板尺寸 最大分辨率 像素点距 亮度(典型) 对比度(典型) 对比度(最大) 视角(水平 / 垂直) CR>10 显示颜色 响应时间 SPLENDID™ 视频增强技术 SPLENDID™ 选择 自动调谐 色温选择 肤色选择 模拟输入 颜色 电源 LED 倾斜 VESA 壁挂安装 防盗锁 额定电压 功耗 温度(运行时) TFT LCD 22"(16:10、55.88 cm)宽屏幕 1680 x 1050 0.282 mm 250 cd/m2 1000:1 50,000,000:1(ASCR 开启时) 170°/160° 16.7 M 5 ms 是 6 种视频预设模式(使用热键) 是(使用热键) 4 种色温 3 种肤色 D-Sub 黑色 蓝色(开机)/ 黄色(待机) +20° ~ -5° 100 x 100 mm 是 交流:100 ~ 240V 开机:< 25 W,待机:< 0.5 W,关机:< 0.
3.
3.4 支持的运行模式 分辨率频率 水平频率(KHz) 垂直频率(Hz) 像素(MHz) 640x480 640x480 640x480 640x480 720x400 800x600 800x600 800x600 800x600 832x624 1024x768 1024x768 1024x768 1152x864 1280x720 1280x768 1280x800 1280x960 1280x1024 1280x1024 1360x768 1366x768 1440x900 1600x1200 1680x1050 (主) 31.5 35.0 37.9 37.5 31.5 35.16 37.9 48.1 46.9 49.7 48.4 56.5 60.0 67.5 45 47.78 49.7 60.0 63.4 79.97 47.71 47.71 55.94 75.0 60 67 72 75 70 56 60 72 75 75 60 70 75 75 60 60 60 60 60 75 60 60 60 60 25.18 30.24 31.50 31.50 28.32 36.00 40.
3-10 第 3 章:一般说明