2015年4月 VX278 系列 液晶显示器 用户指南
目录 声明 .......................................................................................................... iii 安全信息 ........................................................................................................iv 保养和清洁 ......................................................................................................v 1.1 欢迎使用! ..................................................................................... 1-1 1.2 物品清单 ...........................................................
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰,并且 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规 定。这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产 生、使用并且辐射无线电波,如果不按照制造商的说明进行安装和使用,可 能会对无线电通讯产生有害干扰。但是,不能保证在特定安装条件下不会出 现干扰。如果本设备对无线电或电视接收造成了有害干扰(可通过关闭和打 开设备电源来确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 作为 Energy Star® 的合作伙伴,本公司已经确定本产品符合 Energy Star® 在能源效率方面的要求。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身伤 害。 • 电源发生故障时,不要尝试自行修复。请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。如 有任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。不要堵塞这些开口。除非通 风良好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源类 型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 不要使电源板或延长线过载。过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。不要将显示器放置在可能受潮的任何区域 中。将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以防 止因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的提起方式 放置显示器。提起或搬运显示器时,抓住显示器的边缘。不要通过底座或线缆提 起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁显示器表 面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。使用液晶专用清洁剂。切勿直接将清洁剂喷 洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。关闭电源开关,然后重新 打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。屏幕会慢 慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系进行修 理。不要自行修理屏幕! 本指南中使用的约定 警告:这些信息旨在防止您在试图完成一项任务时受伤。 小心:这些信息旨在防止当试图完成一项任务时损坏组件。 重要:您在完成一项任务时必须遵
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http:// www.asus.com 2.
1.1 欢迎使用! 感谢您购买 ASUS® VX278 系列液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮的显示屏, 而且通过一些有用的功能丰富您的观看体验。 利用这些功能,VX278 系列产品为您提供方便愉快的视觉体验! 1.
1.3 组装显示器底座 组装显示器底座: 1. 将底座装到支撑臂上,用螺丝将它们牢固联结。您可以轻松地用手指拧 紧螺丝。 2. 将显示器调整到最适合观看的角度。 我们建议您在桌面上铺上软布,以免损坏显示器。 确保用螺丝将底座固定到支撑臂上。 1.4 连接线缆 连接线缆: 根据第 1-5 页的第 1.5.
1.5 显示器简介 1.5.1 液晶显示器前部 VX278H/Q 1 3 2 4 5 6 7 VX278N 1 1. 3 2 4 5 2 7 QuickFit 按钮: • 此热键可激活专为对齐设计的 QuickFit 功能。 • QuickFit 功能包含 7 页常用网格图案、纸张尺寸和照片尺寸。 • 长按此按钮 2-4 秒钟可以自动将图像调整至最佳位置、时钟和相 位(仅限 VGA 模式)。 • 利用此热键,可以切换采用 SPLENDID™ 视频智能技术的八种视 频预设模式(风景模式、标准模式、剧场模式、游戏模式、夜晚 模式、sRGB 模式、 读取模式和暗室模式)。 • 显示 OSD 菜单时,退出 OSD 菜单或返回上一级菜单。 2.
3. 、 • 4. • 音量热键(仅适用于型号 VX278Q/H) • 对比度热键(仅适用于型号 VX278N) 菜单按钮: • 按此按钮可以进入 OSD 菜单。 • 显示 OSD 时,按此按钮可以进入/选择高亮显示的图标(功能) 。 • 按此按钮可以增大所选功能的值或移动至上一个功能。 • 这也是亮度调整热键。 5. 按钮: 6. 输入选择按钮: • 7.
1.5.
1.5.3 QuickFit 功能 QuickFit 功能包含三种图案:(1) 网格 (2) 纸张尺寸 (3) 照片尺寸。 1. 网格图案 网格图案可帮助设计人员和用户组织页面内容和布局,以达到连贯的外观。 对齐网格 2.
3.
2.1 卸下支撑臂/底座 卸下支撑臂/底座: 2-1 1. 拔掉电源线和信号线。小心地将显示器正面朝下放在整洁的桌子上。 2. 使用螺丝刀取下用于将底座固定到显示器上的两个螺丝。 3.
2.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 VX278 Splendid 风景模式 滤蓝光 标准模式 色彩 剧场模式 图像 游戏模式 输入选择 夜晚模式 系统 sRGB 模式 读取模式 暗房模式 Move 3-1 菜单 Exit 1. 按菜单按钮显示 OSD 菜单。 2. 按 / 和 切换功能。按菜单按钮高亮显示和激活所需的 功能。如果所选的功能有子菜单,再次按 / 和 可以切 换子菜单功能。按菜单按钮高亮显示和激活所需的子菜单功能。 3. 按 4.
3.1.2 1.
2. 滤蓝光 调整 LED 背光灯发出的蓝光的能量级。 VX278 Splendid 0级 滤蓝光 1级 色彩 2级 图像 3级 输入选择 4级 系统 菜单 Move • 0 级:无变化。 • 1~4 级:级数越高,滤掉的蓝光越多。 3.
• 色温:包含三种预设色彩模式(冷色温、常规色、暖色温)和一种 用户模式。 • 肤色:包含三种色彩模式,分别是红润色、自然色和黄艳色。 • Smart view:通过 “Smart View” 技术,可从多种视位观看。 在用户模式下,用户可以配置 R(红色)、G(绿色)和 B(蓝色),调整范围 是 0 ~ 100。 4.
5.
选择输入源:VGA、HDMI、DisplayPort。(VX278Q) VX278 Splendid VGA 滤蓝光 HDMI 色彩 DisplayPort 图像 输入选择 系统 菜单 Move 6. Exit 系统 调整系统配置。 VX278 Splendid Splendid Demo Mode 滤蓝光 音量 色彩 GamePlus 禁用 50 图像 ECO Mode 输入选择 菜单设置 系统 语言 禁用 简体中文 显示信息 恢复出厂模式 Move 菜单 Exit • Splendid Demo Mode:激活 Splendid 功能的演示模式。 • 音量:调整耳机或扬声器输出音量大小。调整范围是 0 到 100(仅限 VX278H/Q.
GamePlus 主菜单 GamePlus - 瞄准点 GamePlus 瞄准点 定时器 (练习模式) GamePlus 主定时器 GamePlus 主定时器位置 位置 3-7 • ECO Mode:激活经济模式以达到省电目的。 • 菜单设置:调整 OSD 屏幕的水平位置、垂直位置、菜单时间、DDD/CI、 以及透明度。 • 语言:选择 OSD 语言。非欧美版本菜单的选项为:英语、繁体中文、简体 中文、日语、波斯语、泰语和印度尼西亚语;欧美版本菜单的选项为:英 语、德语、意大利语、法语、荷兰语、西班牙语、俄语、波兰语、土耳其 语、葡萄牙语、捷克语、克罗地亚语、匈牙利语、罗马尼亚语 • • 显示信息:显示关于显示器的信息。 恢复出厂模式:选择“是”时,所有设置恢复至出厂默认模式。 第 3 章:一般说明
3.2 规格 型号 VX278N VX278H 1920x1080 最大分辨率 300cd/m2 亮度(典型) 固有对比度(典型) 1200:1 动态对比度(典型) ≥80,000,000:1 视角 (CR≤10) 160°(V);170°(H) 显示颜色数 1670 万 (6bit Hi FRC) 响应时间(典型) 1 ms(灰色到灰色) DVI 输入 DVI 及 HDCP D-Sub 输入 HDMI 输入 VX278Q 27.0”W (68.6cm) 面板尺寸 无 无 是 无 是 是 29.1W 开机功耗 Spk 无 是 是 耳机 无 是 是 省电模式 < 0.5W 关机模式 < 0.5W 倾斜 -5° ~ +20° 物理尺寸 (WxHxD) 640.7x451.66x210.1 mm 包装尺寸 (WxHxD) 698x119x560 mm 净重 (Esti.) 毛重 (Esti.) 额定电压 注 4.5 kg 6.7 kg AC 100~240V(内置) *基于Energy Star 6.
3.
3.4 支持的时序列表 VESA / IBM 模式支持时序(D-SUB、DVI-D、VX278H/Q HDMI 输入) 分辨率 640 x 350 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 848 x 480 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 720 1280 x 800 1280 x 960 1280 x 1024 1280 x 1024 1366 x 768 1440 x 900 1680 x 1050 1680 x 1050 1920 x 1080 1920 x 1080 刷新率 70Hz 60Hz 67Hz 75Hz 70Hz 56Hz 60Hz 72Hz 75Hz 60Hz 60Hz 70Hz 75Hz 75Hz 60Hz 60Hz 60Hz 60Hz 75Hz 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz 水平频率 31.469KHz 31.469KHz 35KHz 37.5KHz 31.