User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Basic Installation
- Chapter 3: BIOS Setup
- 3.1 Knowing BIOS
- 3.2 BIOS setup program
- 3.3 My Favorites
- 3.4 Main menu
- 3.5 Ai Tweaker menu
- 3.6 Advanced menu
- 3.6.1 CPU Configuration
- 3.6.2 PCH Configuration
- 3.6.3 PCH Storage Configuration
- 3.6.4 System Agent Configuration
- 3.6.5 USB Configuration
- 3.6.6 Platform Misc Configuration
- 3.6.7 Onboard Devices Configuration
- 3.6.8 APM Configuration
- 3.6.9 Network Stack Configuration
- 3.6.10 HDD/SDD SMART Information
- 3.6.11 Intel(R) Ethernet Controller - 00:1E:99:00:01:1B
- 3.6.12 Intel(R) Ethernet Controller - 00:1E:99:00:01:1C
- 3.7 Monitor menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Exit menu
- 3.11 Updating BIOS
- Chapter 4: Software Support
- 4.1 Installing an operating system
- 4.2 Support DVD information
- 4.3 Software information
- 4.4 AI Suite 3
- 4.4.1 Dual Intelligent Processors 5
- 4.4.2 TPU (Turbo Processing Unit)
- 4.4.3 Turbo App
- 4.4.4 EPU (Energy Processing Unit)
- 4.4.5 Fan Xpert 4
- 4.4.6 PC Cleaner
- 4.4.7 DIGI+ Power Control
- 4.4.8 Ai Charger+
- 4.4.9 USB 3.1 Boost
- 4.4.10 EZ Update
- 4.4.11 System Information
- 4.4.12 Mobo Connect
- 4.4.13 USB BIOS Flashback
- 4.4.14 Push Notice
- 4.5 Audio configurations
- Chapter 5: RAID Support
- Chapter 6: Multi GPU Support
- Appendix
1-8
Chapter 1: Product Introduction
Chapter 1
• You may install varying memory sizes in Channel A, Channel B, Channel C, and
Channel D. The system maps the total size of the lower-sized channel for the dual-
channel conguration. Any excess memory from the higher-sized channel is then
mapped for single-channel operation.
• According to Intel
®
CPU spec, DIMM voltage below 1.65 V is recommended to protect
the CPU.
• Due to the memory address limitation on 32-bit Windows
®
OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
a) Use a maximum of 3GB system memory if you are using a 32-bit Windows
®
OS.
b) Install a 64-bit Windows
®
OS when you want to install 4 GB or more on the
motherboard.
c) For more details, refer to the Microsoft
®
support site at http://support.microsoft.
com/kb/929605/en-us.
• The design of the DIMM fan may vary. Ensure that the DIMM fan ts to the
motherboard.
• The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked
or at a higher frequency, refer to section 3.5 Ai Tweaker menu for manual memory
frequency adjustment.
• For system stability, use a more efcient memory cooling system to support a full
memory load (8 DIMMs) or overclocking condition.
• Memory modules with memory frequency higher than 2133MHz and their
corresponding timing or the loaded XMP prole is not the JEDEC memory standard.
The stability and compatibility of the memory modules depend on the CPU’s
capabilities and other installed devices.
• Always install the DIMMS with the same CAS Latency. For an optimum compatibility,
we recommend that you install memory modules of the same version or data code
(D/C) from the same vendor. Check with the vendor to get the correct memory
modules.
• ASUS exclusively provides hyper DIMM support function.
• Hyper DIMM support is subject to the physical characteristics of individual CPUs. Load
the X.M.P. or D.O.C.P. settings in the BIOS for the hyper DIMM support.
• Visit the ASUS website for the latest QVL.
Memory configurations
You may install 2 GB, 4 GB, 8 GB, and 16GB unbuffered and non-ECC DDR4 DIMMs into
the DIMM sockets.