Motherboard Z490-GUNDAM (WI-FI)
E17176 First Edition October 2020 Copyright © 2020 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Safety information....................................................................................................... iv About this guide........................................................................................................... v Z490-GUNDAM (WI-FI) specifications summary....................................................... vi Connectors with shared bandwidth........................................................................... x Package contents.........................
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product Introduction This chapter describes the features of the motherboard and the new technology it supports. It includes description of the switches, jumpers, and connectors on the motherboard.
Z490-GUNDAM (WI-FI) specifications summary Intel® Socket LGA1200 for 10th Gen Intel® Core™, Pentium® Gold and Celeron® processors* CPU Supports Intel® 14 nm CPU Supports Intel® Turbo Boost Technology 2.0** * Refer to www.asus.com for CPU support list. ** The support of these features depends on the CPU types. Chipset Intel® Z490 Chipset 4 x DIMM, Max. 128GB, DDR4 4800(O.C)/4600(O.C)/4500(O.C)/4400(O. C)/4266(O.C.)/4133(O.C.)/4000(O.C.)/3866(O.C.)/3733(O.C.)/3600(O.C.)/ 3466(O.C.)/3400(O.C.)/3333(O.C.
Z490-GUNDAM (WI-FI) specifications summary Rear USB (Total 6 ports) 2 x USB 3.2 Gen 2 ports (1 x Type-A + 1 x USB Type-C®) 4 x USB 3.2 Gen 1 ports (4 x Type-A) USB Front USB (Total 6 ports) 1 x USB 3.2 Gen 2 front panel connector (supports USB Type-C®) 1 x USB 3.2 Gen 1 header supports additional 2 USB 3.2 Gen 1 ports 1 x USB 2.0 header supports additional 2 USB 2.0 ports 1 x USB 2.0 header supports additional 1 USB 2.0 port (4-pin) Realtek ALC S1200A 7.
Z490-GUNDAM (WI-FI) specifications summary Miscellaneous 1 x AURA Addressable Gen 2 header 2 x AURA RGB headers Internal I/O Connectors 1 x Clear CMOS header 1 x COM Port header 1 x Front Panel Audio header (AAFP) 1 x 20-3 pin System Panel header with Chassis intrude function 1 x Thunderbolt header ASUS ASUS PROTECTION - ASUS DIGI+ VRM (- Digital power design with DrMOS) - ASUS Enhanced DRAM Overcurrent Protection - ASUS ESD Guards - ASUS LANGuard - ASUS Overvoltage Protection - ASUS SafeSlot - ASUS Stainl
Z490-GUNDAM (WI-FI) specifications summary UEFI BIOS ASUS EZ DIY Software Features - ASUS CrashFree BIOS 3 - ASUS EZ Flash 3 - ASUS UEFI BIOS EZ Mode BIOS 192 (128+64) Mb Flash ROM, UEFI AMI BIOS Manageability WOL by PME, PXE Operating System Windows 10 64 - bit Form Factor ATX Form Factor 12 inch x 9.6 inch (30.5 cm x 24.4 cm) Specifications are subject to change without notice. Please refer to the ASUS website for the latest specifications.
Connectors with shared bandwidth RGB_HEADER1 CPU_FAN CPU_OPT KBMS _U32G1 _34 EATX12V_2 EATX12V_1 DIGI+ VRM ASM 1442K CNVI(WIFI) ADD_GEN2 EATXPWR LGA1200 BOOT VGA DRAM CPU DDR4 DIMM_B2* (64bit, 288-pin module) U32G2_1 DDR4 DIMM_B1 (64bit, 288-pin module) DDR4 DIMM_A1 (64bit, 288-pin module) U32G2_C2 LAN_U32G1_78 DDR4 DIMM_A2* (64bit, 288-pin module) HDMI _DP M.2_2(SOCKET3) CHA_FAN1 2280 PCIE SATA V X4 IRST V 2260 2242 M.2_2(SOCKET3) USB3.
Package contents Check your motherboard package for the following items. Motherboard 1 x Z490-GUNDAM (WI-FI) motherboard Cables 2 x SATA 6Gb/s cables 1 x Fan Bracket 1 x I/O Shield Miscellaneous 1 x M.2 Rubber Package 1 x M.2 Screw Package 1 x GUNDAM DIY sticker 1 x ASUS 2x2 dual-band Wi-Fi moving antenna Installation Media 1 x Support DVD Documentation 1 x User manual If any of the above items is damaged or missing, contact your retailer.
Installation tools and components Phillips (cross) screwdriver PC chassis Power supply unit Intel® LGA 1200 CPU Intel® LGA 1200 compatible CPU Fan DDR4 DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) M.2 SSD module (optional) 1 Bag of screws The tools and components in the table above are not included in the motherboard package.
Product Introduction Product Introduction 1.1 Before you proceed 1 Chapter 1 Chapter 1: Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
1.2 Motherboard layout 5 4 1 24.4cm(9.6in) 4 2 12 Chapter 1 RGB_HEADER1 CPU_FAN CPU_OPT KBMS _U32G1 _34 EATX12V_2 EATX12V_1 DIGI+ VRM ASM 1442K ADD_GEN2 18 M.2_2(SOCKET3) 6 CHA_FAN1 2280 PCIE SATA V X4 IRST V 2260 2242 M.2_2(SOCKET3) USB3.2_5 PCIEX16_1 SATA6G_5 Intel® I219-V Intel® Z490 3 128Mb BIOS PCIEX1_2 Super I/O BATTERY 5 9 SATA6G_6 PCIEX1_1 U32G1_910 AIO_PUMP AUDIO 11 30.
Z490-GUNDAM (WI-FI) Page 1-4 1-5 1-7 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-19 1-20 1-21 1-21 Chapter 1 Layout contents 1. CPU socket 2. DIMM slots 3. Expansion slots 4. Fan and Pump headers 5. Power connectors 6. M.2 slots (SOCKET 3) 7. SATA 6Gb/s ports 8. USB 3.2 Gen 2 Front Panel connector 9. USB 3.2 Gen 1 header 10. USB 2.0 headers 11. AURA Addressable Gen2 header 12. AURA RGB headers 13. Clear CMOS header 14. COM Port header 15. Front Panel Audio header 16. System Panel header 17.
1. CPU socket The motherboard comes with a LGA1200 socket designed for 10th Gen Intel® CoreTM, Pentium® Gold and Celeron® Processors. Chapter 1 LGA1200 1-4 • Ensure that you install the correct CPU designed for LGA1200 socket only. DO NOT install a CPU designed for other sockets on the LGA1200 socket. • The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU.
2. DIMM slots The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR4 (Double Data Rate 4) memory modules. Chapter 1 DIMM_B2* DIMM_B1 DIMM_A2* DIMM_A1 A DDR4 memory module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
Memory configurations You may install 4 GB, 8 GB, 16 GB, and 32 GB unbuffered and non‑ECC DDR4 DIMMs into the DIMM sockets. Chapter 1 You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
3. Expansion slots Chapter 1 Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
Recommended VGA configuration Chapter 1 2. 4. Slot Description PCIe 3.0 x16_1 PCIe 3.0 x16_2 Single VGA x16 - Dual VGA x16 x4 • We recommend that you provide sufficient power when running CrossFireX™ or SLI® mode. • Ensure to connect the 8-pin and 4-pin power plugs when running CrossFireX™ mode. • Connect a chassis fan to the chassis fan connectors when using multiple graphics cards for better thermal environment. PCIe 3.0 x16_3 shares bandwidth with PCIe3.0 x1_1 and PCIe3.0 x1_1. Hyper M.
4. Fan and Pump headers CPU_FAN B CPU_OPT C AIO_PUMP D CHA_FAN1 E CHA_FAN2 F CHA_FAN3 GND A FAN PWM FAN IN FAN PWR A B Chapter 1 The Fan and Pump headers allow you to connect fans or pumps to cool the system. E Header CPU_FAN CPU_OPT CHA_FAN1 CHA_FAN2 CHA_FAN3 AIO_PUMP GND FAN PWR FAN IN FAN PWM C D F • DO NOT forget to connect the fan cables to the fan headers. Insufficient air flow inside the system may damage the motherboard components.
5. Power connectors These Power connectors allow you to connect your motherboard to a power supply. The power supply plugs are designed to fit in only one orientation. Find the proper orientation and push down firmly until the power supply plugs are fully inserted.
6. M.2 slot Chapter 1 The M.2 slot allows you to install M.2 devices such as M.2 SSD modules. A B A M.2_2(SOCKET3) B M.2_1(SOCKET3) • M.2_1 slot (Key M), type 2242/2260/2280/22110 (supports SATA & PCIe 3.0 x4 mode). • M.2_2 slot (Key M), type 2242/2260/2280 (supports SATA & PCIe 3.0 x4 mode). • M.2_1 shares bandwidth with SATA6G_2. When M.2_1 runs SATA mode, SATA6G_2 will be disabled. • M.2_2 shares bandwidth with SATA6G_56. When M.2_2 is occupied, SATA6G_56 will be disabled. • M.
7. SATA 6Gb/s ports The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and hard disk drives via a SATA cable.
8. USB 3.2 Gen 2 Front Panel connector Chapter 1 The USB 3.2 Gen 2 connector allows you to connect a USB 3.2 Gen 2 module for additional USB 3.2 Gen 2 ports. The USB 3.2 Gen 2 connector provides data transfer speeds of up to 10 Gb/s. CC2 D+ DGND RX2RX2+ GND TX2TX2+ VBUS VBUS TX1+ TX1GND RX1+ RX1VBUS CC1 SBU1 SBU2 USB3.2_5 The USB 3.2 Gen 2 module is purchased separately.
9. USB 3.2 Gen 1 header The USB 3.2 Gen 1 header allows you to connect a USB 3.2 Gen 1 module for additional USB 3.2 Gen 1 ports. The USB 3.2 Gen 1 header provides data transfer speeds of up to 5 Gb/s. Chapter 1 U32G1_910 A PIN 1 USB3+5V IntA_P2_SSRXIntA_P2_SSRX+ GND IntA_P2_SSTXIntA_P2_SSTX+ GND IntA_P2_DIntA_P2_D+ USB3+5V IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ GND The USB 3.2 Gen 1 module is purchased separately. The plugged USB 3.
10. USB 2.0 header Chapter 1 Connect the USB module cable to these connectors, then install the module to a slot opening at the front of the system chassis. These USB headers comply with USB 2.0 specifications and support up to 480 Mbps connection speed. USB6 A USB+5V USB_P6USB_P6+ GND PIN 1 USB1112 PIN 1 A B USB+5V USB_P2USB_P2+ GND USB+5V USB_P1USB_P1+ GND NC B DO NOT connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB 2.
11. Aura Addressable Gen2 header The Addressable Gen2 header allows you to connect individually addressable RGB WS2812B LED strips or WS2812B based LED strips. Chapter 1 ADD_GEN2 Ground Data +5V PIN 1 The Addressable Gen2 header supports WS2812B addressable RGB LED strips (5V/ Data/Ground), with a maximum power rating of 3A (5V), and the addressable headers on this board can handle a combined maximum of 500 LEDs.
12. AURA RGB LED header The AURA RGB LED header allows you to connect RGB LED strips. A RGB_HEADER1 Chapter 1 A PIN 1 +12V G R B B RGB_HEADER2 B R G +12V PIN 1 B The AURA RGB LED header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum power rating of 3A (12V). Before you install or remove any component, ensure that the power supply is switched off or the power cord is detached from the power supply.
13. Clear CMOS header Chapter 1 This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. +3V_BAT GND CLRTC PIN 1 To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Use a metal object such as a screwdriver to short the two pins.
14. COM Port header Chapter 1 This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. PIN 1 DCD TXD GND RTS RI RXD DTR DSR CTS COM The COM module is purchased separately. 15. Front Panel Audio header The front panel audio header is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this header.
16. System Panel header The System Panel header supports several chassis-mounted functions. Chapter 1 +5V Ground Ground Speaker Intruder# PLED+ PLEDPWRBTN# GND PLED PWRSW SPEAKER CHASSIS PANEL GND PLED- HDD_LED+ HDD_LEDGround RSTCON# NC PLED+ PIN 1 HDD_LED RESET PLED • System Power LED header (PLED) The 2-pin header allows you to connect the System Power LED.
17. Thunderbolt header I2C_SCL I2C_SDA I2C_IRQ# RTD3_POWER_EN S_SLP_S0#_IDLE PERST_N WAKE# Chapter 1 The Thunderbolt header allows you to connect an add-on Thunderbolt I/O card that supports Intel’s Thunderbolt Technology, allowing you to connect up to six Thunderbolt-enabled devices and a DisplayPort-enabled display in a daisy-chain configuration. TB_HEADER RTD3_SW FORCE_PWR GND SLP_S3# SLP_S5# GND PIN 1 The add-on Thunderbolt I/O card and Thunderbolt cables are purchased separately. 18.
Chapter 1 1-22 Chapter 1: Product Introduction
Chapter 2: Basic Installation Basic Installation 2.1 Building your PC system 2 The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. CPU installation • Ensure that you install the correct CPU designed for LGA1200 socket only. DO NOT install a CPU designed for LGA1155, LGA1156, and LGA1151 sockets on the LGA1200 socket.
Chapter 2 2-2 Chapter 2: Basic Installation
2.1.2 Cooling system installation Apply Thermal Interface Material to the CPU cooling system and CPU before you install the cooling system, if necessary.
To install an AIO cooler If you wish to install an AIO cooler, we recommend installing the AIO cooler after installing the motherboard into the chassis.
DIMM installation Chapter 2 2.1.
2.1.4 M.2 installation For type 22110 M.2 on M.2_1 slot 11 For type 2242 / 2260 / 2280 M.2 on M.2_1 slot 11 11 22 22 33 11 Chapter 2 1 1 66 66 44 1 3 44 4 1 3 88 7878 88 7 8 88 OPTIONAL 8 4 4 77 66 6 8 4 1 66 6 56 1 2 2 6 5 11 2 33 44 44 6 33 3 OPTIONAL 11 22 22 1 1 2 5656 2 55 3 3 11 1 33 11 4 66 8 55 6 55 5 7 2-6 78 8 • This M.2 rubber pad is optional for when installing a single 6 6 sided M.2 storage device.
Fan bracket installation Chapter 2 2.1.5 When using high performance settings whilst overclocking, ensure to install the fan holder for additional fan(s). • You may install 12V (1A, 12W), 40mm x 40mm fans or 50mm x 50mm fans. • Ensure to use the bundled screws that came with your fans. • Fans are purchased separately.
2.1.6 1. Motherboard installation Install the ASUS I/O Shield to the chassis rear I/O panel. Some sharp edges and points might cause physical injury. We recommend you put on cut or puncture resistant gloves before motherboard and I/O shield installation. Chapter 2 2. 2-8 Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel.
Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. Chapter 2 3. DO NOT over tighten the screws! Doing so can damage the motherboard.
2.1.7 ATX power connection Chapter 2 OR 2-10 AND • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power plugs.
2.1.
2.1.9 Front I/O connector To install the front panel header To install USB 3.2 Gen 2 connector USB 3.2 Gen 2 Chapter 2 This connector will only fit in one orientation. Push the connector until it clicks into place. To install USB 3.2 Gen 1 connector To install USB 2.0 connector USB 3.1 Gen 1 USB 2.
2.1.
To install ThunderboltEX 3-TR card 6-pin PCIe power connector USB Type-C® port connects to Thunderbolt devices Chapter 2 MiniDP in port connects to DP out port on the motherboard or a VGA card USB 2.0 header Thunderbolt header Ensure to install the ThunderboltEX 3-TR card to a PCIe slot from PCH. 2-14 • Step 6 is optional, please connect a 6-pin PCIe power connector when you wish to use the USB Type-C® port Thunderbolt quick charge feature to charge a 5V or more device.
2.1.11 Wi-Fi antenna installation Installing the ASUS 2x2 dual band W-Fi antenna • Ensure that the ASUS 2x2 dual band Wi-Fi antenna is securely installed to the Wi-Fi ports. • Ensure that the antenna is at least 20 cm away from all persons. Chapter 2 Connect the bundled ASUS 2x2 dual band Wi-Fi antenna connector to the Wi-Fi ports at the back of the chassis. The illustration above is for reference only.
2.2 Motherboard rear and audio connections 2.2.1 Rear I/O connection 1 5 2 3 4 6 7 5 8 9 10 Chapter 2 Rear panel connectors 1. 2. 3. 4. 5. 6. 7. PS/2 mouse/keyboard combo port DisplayPort USB 3.2 Gen 2 Type-A port Ethernet (RJ-45) port* USB 3.2 Gen 1 Type-A ports 34 and 78 HDMI™ port USB Type-C® 8. Wi-Fi 802.11 a/b/g/n/ac/ax, Bluetooth V5.1 9. Optical S/PDIF OUT port 10. audio jacks** * and ** : Refer to the tables on the next page for LAN port LEDs, and audio port definitions.
* Ethernet port LED indications Activity Link LED Speed LED Status Description Status Description Off No link Off Orange Linked Orange 100 Mbps connection Blinking Data activity Green ACT/LINK LED SPEED LED 10 Mbps connection 1 Gbps connection LAN port 4-channel 5.1-channel 7.
Connect to Stereo Speakers Connect to 2-channel Speakers Chapter 2 Connect to 4-channel Speakers 2-18 Chapter 2: Basic Installation
Chapter 2 Connect to 5.1-channel Speakers Connect to 7.
2.3 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Ensure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: 6. a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
Chapter 3: BIOS and RAID Support BIOS and RAID Support 3 For more details on BIOS and RAID configurations, please refer to www.asus.com/ support. 3.1 Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system.
3.2 BIOS setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screens include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup, press or during the Power-On Self Test (POST). If you do not press or , POST continues with its routines. Entering BIOS Setup after POST To enter BIOS Setup after POST: • Press ++ simultaneously.
3.3 ASUS EZ Flash 3 The ASUS EZ Flash 3 feature allows you to update the BIOS without using an OS‑based utility. Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu or press hotkey . To update the BIOS by USB: • This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only.
3.4 ASUS CrashFree BIOS 3 The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the BIOS file. The BIOS file in the motherboard support DVD may be older than the BIOS file published on the ASUS official website. If you want to use the newer BIOS file, download the file at https://www.asus.
3.5 RAID configurations The motherboard comes with the Intel® Rapid Storage Technology that supports RAID 0, RAID 1, RAID 5 and RAID 10 configuration. For more information on configuring your RAID sets, please refer to the RAID Configuration Guide which you can find at https://www.asus.com/support, or by scanning the QR code. RAID definitions RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
Chapter 3 3-6 Chapter 3: BIOS Setup
Appendix Appendix Notices FCC Compliance Information Responsible Party: Address: Phone / Fax No: Asus Computer International 48720 Kato Rd., Fremont, CA 94538, USA (510)739-3777 / (510)608-4555 Identification of the assembled product: INTEL Wi-Fi 6 AX201 Identification of the modular components used in the assembly: Model Name: Wi-Fi 6 AX201 FCC ID: PD99560NG This device complies with part 15 of the FCC Rules.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Google™ License Terms Copyright© 2020 Google Inc. All Rights Reserved. Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements. Please refer to http://csr.asus.com/Compliance.
DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products. DO NOT throw the mercury-containing button cell battery in municipal waste.
Appendix Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/ The WiFi operating in the band 5150-5350MHz shall be restricted to indoor use for countries listed in the table below: Déclaration simplifiée de conformité de l’UE ASUSTek Computer Inc.
Z490-GUNDAM (WI-FI) ASUSTek Computer Inc. ขอประกาศในที่นี้ว่าอุปกรณ์นี้มีความสอดคล้องกับความ ต้องการที่จำ�เป็นและเงื่อนไขที่เกี่ยวข้องอื่น ๆ ของบทบัญญัติข้อกำ�หนด 2014/53/EU เนื้อหาที่สมบูรณ์ของประกาศความสอดคล้องกับ EU มีอยู่ที่ https://www.asus.com/support/ การทำ�งานของ WiFi ที่ 5150-5350MHz ถูกจำ�กัดให้ใช้ในอาคารสำ�หรับประเทศที่แสดงในตาราง Basitleştirilmiş AB Uyumluluk Bildirimi ASUSTek Computer Inc.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax Web site Technical Support Telephone Online support 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 https://www.asus.com +86-21-38429911 https://qr.asus.com/techserv ASUS COMPUTER INTERNATIONAL (America) Address 48720 Kato Rd., Fremont, CA 94538, USA Telephone +1-510-739-3777 Fax +1-510-608-4555 Web site https://www.asus.
