Motherboard SABERTOOTH Z97 MARK 1/USB 3.
ii
C10094 1.00 版 2015 年 1 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License (“GPL”) and under the Lesser General Public License Version (“LGPL”). The GPL and LGPL licensed code in this product is distributed without any warranty. Copies of these licenses are included in this product.
五年質保 全國聯保 華碩產品質量保證卡 請用剪刀沿虛線剪下 尊敬的華碩產品用戶: 首先非常感謝您選用華碩公司產品,讓我們有機會向您提供優質的服務。為了使我們的服務讓 您更滿意,在購買後請您認真閱讀此說明並妥善保存此質量保證卡。 保修說明注意事項: 一、 請將此質量保證卡下方的用戶資料填寫完整,並由最終直接經銷商加蓋印章,如果沒有加蓋 印章,請找原購買處補蓋以保障您的權益。請務必保留購買發票或複印件,否則華碩公司將 以產品的出廠日期為參照進行保修。 二、 華碩公司對在中國大陸地區(不包括港澳台地區)發售的、經合法渠道銷售給消費者的華碩 主板及顯卡產品實行五年的免費保修服務。 三、 華碩公司對在中國大陸地區(不包括港澳台地區)發售的、經合法渠道銷售給消費者的華碩 主板及顯卡產品實行全國聯保服務。注: A. 消費者必須出具正規購買發票或國家認可的有效憑證方可享受全國聯保。 B. 如消費者無法出具正規購買發票或國家認可的有效憑證,則需送修至原購買經銷商 處享受保修服務。 四、 若經本公司判斷屬下列因素,則不屬於免費保修服務的範圍,本公司將有權利收取維修費 用: A.
vi
目錄內容 華碩產品質量保證卡................................................................................................................... v 安全性須知.....................................................................................................................................x 電氣方面的安全性............................................................................................................x 操作方面的安全性............................................................................................................
目錄內容 2.3 主板後側與音頻連接端口..........................................................................................2-12 2.3.1 後側面板連接端口.........................................................................................2-12 2.3.2 音頻輸出/輸入連接圖標說明....................................................................2-14 2.4 第一次啟動電腦.............................................................................................................2-16 2.5 關閉電源................................................................
目錄內容 4.3 4.4 4.5 4.6 4.2.1 運行驅動程序及應用程序 DVD 光盤....................................................... 4-1 4.2.2 取得軟件用戶手冊........................................................................................... 4-3 軟件信息............................................................................................................................. 4-4 華碩 AI Suite 3 程序..................................................................................................... 4-4 4.4.1 Ai Charger+.....................
安全性須知 電氣方面的安全性 • 為避免可能的電擊造成嚴重損害,在搬動電腦主機之前,請先將電腦電源線暫時 從電源插槽中拔掉。 • 當您要加入硬件設備到系統中時,請務必先連接該設備的數據線,然後再連接電 源線。可能的話,在安裝硬件設備之前先拔掉電腦的電源電源線。 • 當您要從主板連接或拔除任何的數據線之前,請確定所有的電源線已事先拔掉。 • 在使用擴展卡或擴展卡之前,我們建議您可以先尋求專業人士的協助。這些設備 有可能會干擾接地的迴路。 • 請確定電源的電壓設置已調整到本國/本區域所使用的電壓標準值。若您不確定您 所屬區域的供應電壓值為何,請就近詢問當地的電力公司人員。 • 如果電源已損壞,請不要嘗試自行修復。請將之交給專業技術服務人員或經銷商 來處理。 操作方面的安全性 • 在您安裝主板以及加入硬件設備之前,請務必詳加閱讀本手冊所提供的相關信 息。 • 在使用產品之前,請確定所有的排線、電源線都已正確地連接好。若您發現有任 何重大的瑕疵,請儘速聯絡您的經銷商。 • 為避免發生電氣短路情形,請務必將所有沒用到的螺絲、回形針及其他零件收 好,不要遺留在主板上或電腦主機中。 • 灰塵、濕氣以及
關於這本用戶手冊 產品用戶手冊包含了所有當您在安裝華碩 SABERTOOTH Z97 MARK 1/USB 3.
提示符號 為了能夠確保您正確地完成主板設置,請務必注意下面這些會在本手冊中出現的標 示符號所代表的特殊含意。 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到電腦主板元件。 要:此符號表示您必須要遵照手冊所描述之方式完成一項或多項軟硬件 重 的安裝或設置。 注意:提供有助於完成某項工作的訣竅和其他額外的信息。 哪裡可以找到更多的產品信息 您可以通過下面所提供的兩個渠道來獲得您所使用的華碩產品信息以及軟硬件的升 級信息等。 1. 華碩網站 您可以到 http://www.asus.com.cn 華碩電腦互聯網站取得所有關於華碩軟硬件產 品的各項信息。 2.
電子電氣產品有害物質限制使用標識要求:圖中之數字為產品之環保 使用期限。僅指電子電氣產品中含有的有害物質不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 有害物質的名稱及含量說明標示: 有害物質 部件名稱 鉛(Pb) 汞(Hg) 鎘(Cd) 六價鉻 (Cr(VI)) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 印刷電路板及其電 子組件 × ○ ○ ○ ○ ○ 外部信號連接口及 線材 × ○ ○ ○ ○ ○ 本表格依據 SJ/T 11364 的規定編制。 ○: 表示該有害物質在該部件所有均質材料中的含量均在 GB/T 26572 規定的限量 要求以下。 ×: 表示該有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 規定 的限量要求,然該部件仍符合歐盟指令 2011/65/EU 的規范。 備註:此產品所標示的環保使用期限,系指在一般正常使用狀況下。 xiii
SABERTOOTH Z97 MARK 1/USB 3.1 規格列表 中央處理器 支 持採用 LGA1150 規格插槽的第四代/全新第四代/第五代 Intel® Core™ i7/Core™ i5/Core™ i3/Pentium/Celeron 處 理器 支持 22nm 處理器 支持 Intel® Turbo Boost 2.0 技術 * 對 Intel® Turbo Boost 2.0 技術的支持依照處理器的類型而不同 ** 請訪問 www.asus.com.cn 取得最新的 Intel 處理器支持列表 芯片組 Intel® Z97 Express 芯片組 內存 4 x 使用符合 non-ECC unbuffered DDR3 1866/1600/1333 MHz 內存,最高可以擴展至 32GB 內存 支持雙通道內存架構 支持 Intel® Extreme Memory Profile(XMP)技術 * 對高速內存的支持會受到特定處理器之物理特性的影響,請訪問 www.asus.com.
SABERTOOTH Z97 MARK 1/USB 3.
SABERTOOTH Z97 MARK 1/USB 3.1 規格列表 其他特殊功能 USB 3.1 Boost 功能提供 USB 3.1/3.0 傳輸速度 USB BIOS Flashback USB Charger+ Remote GO! 華碩 UEFI BIOS EZ Mode 功能,提供友善的圖形用戶界面 Turbo LAN 推播信息(Push Notice)通過智能型設備實時監控電腦狀態 AI Suite 3 智能管家三代 華碩 Q-Connector 華碩 Q-Shield 華碩 Q-LED(處理器、內存、VGA、啟動設備指示燈) 華碩 Q-Slot 華碩 Q-DIMM 華碩 O.C. Profile 華碩 CrashFree BIOS 3 華碩 EZ Update Disk Unlocker 華碩 EZ Flash 2 多國語言 BIOS 後側面板設備連接端口 1 x DisplayPort 連接端口 1 x HDMI 連接端口 1 x 光纖 S/PDIF 數字音頻輸出連接端口 1 x USB BIOS Flashback 按鈕 1 x RJ-45 網絡連接端口 2 x USB 3.1/3.
SABERTOOTH Z97 MARK 1/USB 3.1 規格列表 內置 I/O 設備連接端口 1 1 1 1 1 1 3 1 1 1 1 x x x x x x x x x x x 前置風扇連接插座(AAFP) 24-pin EATX 電源插座 8-pin EATX 12V 電源插座 系統面板插座(Q-Connector) MemOK! 按鈕 DRCT(DirectKey)插座 溫度感應器插座(T_Sensor) S/PDIF 數字音頻輸出插座 TPM 插座 5-pin Thunderbolt 接口支持 ASUS ThunderboltEX 系列 Clear CMOS 跳線帽 BIOS 功能 64Mb Flash ROM、UEFI AMI BIOS、PnP、DMI 2.7、WfM 2.0、S M B I O S 2.7、A C P I 5.
產品包裝 在您拿到本主板包裝盒之後,請馬上檢查下面所列出的各項標準配件是否齊全。 nual User Ma 華碩 SABERTOOTH Z97 MARK 1/USB 3.1 主板 用戶手冊、認證和保修卡 驅動程序與 應用程序 DVD 光盤 4 x Serial ATA 6.0 Gb/s 排線 1 x ASUS SLI™ 橋接連接器 1 x ASUS Q-Shield 擋板 1 x 二合一 ASUS Q-Connector 套件 1 x 35 mm 輔助風扇 1 x 40 mm 輔助風扇 2 x 短的風扇螺絲 4 x 長的風扇螺絲 3 x PCIe x16 插槽防塵蓋 3 x PCIe x1 插槽防塵蓋 2 x DRAM 插槽防塵蓋 後側 I/O 灰塵過濾器 TUF 配件用戶手冊 1 x 插座蓋組合(LAN 蓋、 HDMI 蓋、DVI 蓋、DP 蓋、前 側 USB 3.0 蓋) 3 x 熱敏電阻排線 2 x 內部 USB 2.
安裝工具與配件 一袋螺絲 Philips (十字) 螺絲起子 PC 機箱 電源供應設備 Intel® LGA1150 處理器 Intel® LGA1150 兼容處理器風扇 內存條 SATA 硬盤 SATA 光驅(選購) 顯卡(選購) 上表所列的工具與元件並不包含在主板包裝盒內。 xix
xx
第一章 1.1 特殊功能 1.1.1 產品特寫 支持 LGA1150 規格的第四代/全新第四代/第五代 Intel® Core™ i7/Core™ i5/Core™ i3/Pentium®/Celeron® 處理器 本主板支持最新 LGA1150 封裝的第四代/全新第四代/第五代 Intel® Core™ i7/i5/ i3/Pentium®/Celeron® 處理器,並通過 GPU、雙通道 DDR3 內存插槽與 PCI Express 2.0/3.0 擴展插槽,能提供最佳的繪圖顯示與系統運算性能。 採用 Intel® Z97 Express 芯片組 Intel® Z97 Express 芯片組採用最新的單芯片設計,是專為支持最新的 LGA1150 插槽的第四代/全新第四代/第五代 Intel® Core™ i7/i5/i3/Pentium®/Celeron® 處理器 所設計,通過連續的點對點鏈接增加帶寬與穩定性,並增強系統性能。原生支持高達 六組 USB 3.0 連接端口、六組 SATA 6 Gb/s 連接端口與 M.
Intel® Smart Response Technology 功能 第一章 Intel® Smart Response Technology 用來提升整個系統性能,通過已經安裝的高速 SSD(最小空間需為 18.
1.1.3 “TUF ENGINE!” 電源設計 數字電源控制 第一章 華碩 DIGI+ 電源控制包括有多重數字電壓控制器,可以極精準的調控 VRAM、 DRAM 內存與處理器。這項革命性的創新與領先企業的華碩技術提供極度精確的電 壓,帶給您最佳的效率、穩定性與系統性能。 TUF Components(電感、電容 & MOSFET;軍用標準認證) TUF 新電感 軍規等級的新電感擁有較以往多出 18.5% 的散熱區域,可以運行 13.6% 之高 的冷卻效果,這也表示您的電腦可以獲得更長的使用壽命。 10K Ti-Caps 電容 日本製的 10K 黑色電容提供高於以往 20% 之溫度耐受性,可以提升五倍的使 用壽命。 TUF MOSFETs 電晶體 TUF MOSFETs 電晶體通過嚴格的軍事標準測試,擁有較低的漏極至源極電阻 (drain-to-source resistance,RDS),可以獲得更好的性能。 * 較低的漏極至源極電阻(RDS)意即電力更有效率,並因此讓電晶體產生較 少的熱度。 1.1.
1.1.5 華碩 EZ DIY 華碩 UEFI BIOS(EZ Mode) 第一章 華碩 UEFI BIOS 程序提供可由鼠標控制操作的友善的圖像化界面,在超越常規鍵 盤的 BIOS 控制,為您提供更多的靈活性、方便性與易於瀏覽 UEFI BIOS,相較常規 的 BIOS 版本,可以提供您雙選擇模式和支持原生大於 2.
1.1.
1.1.7 其他特殊功能 支持 DisplayPort 第一章 DisplayPort 是一個數字顯示界面標準,可以較標準的排線提供高達 10.8 Gbps 的 帶寬,以及億萬種顏色顯示與雙向的溝通,只要通過單一數據線,就可以傳送更快速 的顯示刷新率,以及更高分辨率的數字圖像,並且支持藍光光盤的 HDCP 數字內容 保護。將連接至 DisplayPort 1.
1.2 主板概述 1.2.1 主板安裝前 第一章 主板以及擴展卡都是由許多精密複雜的集成電路元件、集成性芯片等所構成。而這 些電子性零件很容易因靜電的影響而導致損壞,因此,在您動手更改主板上的任何設 置之前,請務必先作好以下所列出的各項預防措施。 • 在處理主板上的內部功能設置時,您可以先拔掉電腦的電源線。 • 為避免生成靜電,在拿取任何電腦元件時除了可以使用防靜電手環之 外,您也可以觸摸一個有接地線的物品或者金屬物品像電源外殼等。 • 拿取集成電路元件時請盡量不要觸碰到元件上的芯片。 • 在您刪除任何一個集成電路元件後,請將該元件放置在絕緣墊上以隔 離靜電,或者直接放回該元件的絕緣包裝袋中保存。 • 在您安裝或刪除任何元件之前,請確認 ATX 電源的電源開關是切換 到關閉(O F F)的位置,而最安全的做法是先暫時拔出電源的電源 線,等到安裝/刪除工作完成後再將之接回。如此可避免因仍有電力 殘留在系統中而嚴重損及主板、外圍設備、元件等。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
1.2.2 主板結構圖 第一章 關於面板連接插座與內部連接插座的相關信息,請參考 1.2.9 內部連接 端口 與 2.3.
主板元件說明 頁數 1. ATX power connectors (24-pin EATXPWR, 8-pin EATX12V) 1-35 2. CPU, optional, chassis, and assistant fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-4; 3-pin ASST_FAN1-2, 4-pin ASST_FAN3) 1-33 3. LGA1150 CPU socket 1-10 4. DDR3 DIMM slots 1-11 5. MemOK! button 1-25 6. USB 3.0 connector (20-1 pin USB3_34) 1-30 7. Intel® Z97 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-2 [brown]; SATA6G_3-4 [black] SATA Express [black at the bottom]) 1-29 8.
1.2.
1.2.4 系統內存 DDR3 內存條擁有與 DDR2 或 DDR 內存條相同的外觀,但是 DDR3 內 存插槽的缺口與 DDR2 或 DDR 內存插槽不同,以防止插入錯誤的內存 條。 內存建議設置 華碩 SABERTOOTH Z97 MARK 1/USB 3.
內存設置 您可以任意選擇使用 2GB、4GB 與 8GB 的 unbuffered non-ECC DDR3 內存條至 本主板的內存插槽上。 第一章 • 您可以在 Channel A、Channel B 安裝不同容量的內存條,在雙通道 設置中,系統會檢測較低容量通道的內存容量。任何在較高容量通道 的其他內存容量,會被檢測為單通道模式運行。 • 根據 Intel 處理器規格,建議內存電壓低於 1.65V 以保護處理器。 • 由於 32-bit Windows 操作系統內存地址的限制,當您安裝 4GB 或 更多的內存條時,系統實際可用的總內存只有 3GB 或更少。為充分 利用內存,您可以運行以下任一動作: a) 若您使用 32-b i t W i n d o w s 操作系統,建議系統內存最高安裝 3GB 即可。 b) 當 您的主板安裝 4G B 或更多的內存時,建議您安裝 64-b i t Windows 操作系統。 c) 若需要更詳細的數據,請訪問 Microsoft 網站 http://support. microsoft.
SABERTOOTH Z97 MARK 1/USB 3.1 主板合格供應商列表(QVL) DDR3 3200MHz 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 2 4 AVEXIR AVD3UH32001304G-4CI(XMP) 16GB ( 4x 4GB ) SS - - 13-15-15-35 1.65V • • G.SKILL F3-3200C12Q-16GTXDG(XMP) 16GB ( 4x 4GB ) SS - - 12-15-15-35 1.65V • • DDR3 3100MHz 記憶體插槽支 援(選購) 供應商 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 2 4 AVEXIR AVD3UH31001204G-4CI(XMP) 16GB ( 4x 4GB ) SS - - 12-14-14-35 1.
DDR3 2800MHz 記憶體插槽支 援(選購) 第一章 供應商 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 AVEXIR AVD3UH28001208G-4BZ1(XMP) 32GB (4x8GB ) DS - - 12-14-14-35 1.65V • • A_DATA AX3U2800W4G12(XMP) 16GB (4x4GB ) SS - - 12-14-14-36 1.65V • • A_DATA AX3U2800W8G12(XMP) 32GB (4x8GB ) DS - - 12-14-14-36 1.65V • G.SKILL F3-2800C12Q-32GTXD(XMP) 32GB (4x8GB ) DS - - 12-13-13-35 1.65V • • G.SKILL F3-2800C12Q-32GTXDG(XMP) 32GB (4x8GB ) DS - - 12-14-14-35 1.65V • • G.
DDR3 2133MHz 記憶體插槽支援( 選購) 供應商 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 A-DATA AX3U2400W4G11-DMV(XMP) 8GB ( 2x 4GB ) SS - - 11-13-13-35 1.65 • • • A-DATA AX3U2400W8G11-DMV(XMP) 16GB ( 2x 8GB ) DS - - 11-13-13-35 1.65 • • • Apacer 78.BAGFL.AFD0C(XMP) 8GB ( 2x 4GB ) DS - - 11-12-12-30 - • • • Apacer 783BAGF3.AFD0C(XMP) 8GB ( 2x 4GB ) DS - - 11-11-11-30 - • • • CORSAIR CMD16GX3M2A2400C10 (Ver4.21)(XMP) 16GB ( 2x 8GB ) DS - - 10-12-12-31 1.
DDR3 2133MHz 記憶體插槽支援( 選購) 第一章 供應商 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 A-DATA AX3U2133W4G10-DR(XMP) 8GB ( 2x 4GB ) SS - - 10-11-11-30 1.65 • • • A-DATA AX3U2133W8G10-DR(XMP) 16GB ( 2x 8GB ) DS - - 10-11-11-30 1.65 • • • Apacer 78.BAGE4.AFD0C(XMP) 8GB ( 2x 4GB ) DS - - 9-9-9-24 - • • • Apacer AHU04GFB33CAQ3R(XMP) 4GB DS - - 11-13-13-31 - • • • CORSAIR CMD16GX3M2A2133C9 (Ver4.21)(XMP) 16GB ( 2x 8GB ) DS - - 9-11-11-31 1.
DDR3 1866MHz 記憶體插槽支 援(選購) 供應商 型號 容量 SS/ DS 晶片 廠牌 晶片 型號 時脈 電壓 1 2 CORSAIR CMD16GX3M2A1866C9 (Ver5.29) (XMP) 16GB ( 2x 8GB ) DS - - 1866 9-9-9-27 1.5 • • CORSAIR CMD16GX3M4A1866C9 (Ver4.13) (XMP) 16GB ( 4x 4GB ) DS - - 9-10-9-27 1.5 • • • CORSAIR CMD16GX3M4A1866C9 (Ver8.16) (XMP) 16GB ( 4x 4GB ) DS - - 9-10-9-27 1.5 • • • CORSAIR CMD32GX3M4A1866C9 (Ver3.24) (XMP) 32GB ( 4x 8GB ) DS - - 9-10-9-27 1.5 • • • CORSAIR CMD8GX3M2A1866C9 (Ver4.
DDR3 1600MHz 記憶體插槽支 援(選購) 第一章 供應商 型號 容量 SS/ DS 晶片廠牌 晶片型號 時脈 電壓 1 2 4 A-DATA AD3U1600W4G11 4GB SS A-DATA 3WCD-1211A 11-11-11-28 - • • • A-DATA AD3U1600W8G11 8GB DS A-DATA 3WCD-1211A 11-11-11-28 - • • • A-DATA ADDU1600W4G11-B 4GB SS A-DATA DWND-1211A 9-9-9-24 - • • • A-DATA ADDU1600W8G11-B 8GB DS ELPIDA J4208EBBG-GN-F 9-9-9-24 - • • • A-DATA AX3U1600W4G9-DB(XMP) 8GB ( 2x 4GB ) SS - - 9-9-9-24 1.
DDR3 1600MHz(表格接上頁) 型號 容量 SS/ DS 晶片廠牌 晶片型號 時脈 電壓 1 2 4 Crucial BLS4G3D1609DS1S00 .16FMR(XMP) 4GB DS - - 1600-9-99-24 1.5 • • • Crucial BLT4G3D1608DT1TX0 .16FM(XMP) 4GB DS - - 8-8-8-24 1.5 • • • Elixir M2X2G64CB88G7N-DG(XMP) 2GB SS Elixir N2CB2G80GN-DG 9-9-9-28 - • • • Elixir M2X4G64CB8HG5N-DG(XMP) 4GB DS Elixir N2CB2G80GN-DG 9-9-9-28 - • • • G.SKILL F3-12800CL9D-8GBSR2(XMP) 8GB ( 2x 4GB ) DS - - 9-9-9-24 1.25 • • • G.
DDR3 1600MHz(表格接上頁) 記憶體插槽支援 (選購) 第一章 供應商 型號 容量 SS/ DS 晶片廠牌 晶片型號 時脈 電壓 Patriot PV316G160C9K(XMP) 16GB ( 2x 4GB ) SS - - 1600-9-99-24 1.5 • • • Patriot PV316G160C9K(XMP) 16GB ( 2x 8GB ) SS - - 1600-9-99-24 1.5 • • • SanMax SMD-4G28N1P-16KM 4GB SS ELPIDA J4208BBBG-GN-F 1600 - • • • SanMax SMD-4G68HP-16KZ 4GB DS Hynix H5TQ2G83BFRPBC - 1.
DDR3 1333MHz 記憶體插槽支援 (選購) 供應商 型號 容量 SS/ DS 晶片廠牌 晶片型號 時脈 電壓 AMD AE32G1339U1-U 2GB SS AMD 23EY4587MB3H - 1.5 • • • AMD AE34G1339U2-U 4GB DS AMD 23EY4587MB3H - 1.5 • • • Apacer 78.B1GDE.
DDR3 1333MHz(表格接上頁) 記憶體插槽支 援(選購) 第一章 供應商 型號 容量 SS/ DS 晶片廠牌 晶片型號 時脈 電壓 1 2 4 Mach Xtreme MXD3U133316GQ 16GB ( 4x 4GB ) DS - - - - • • • Mach Xtreme MXD3V13332GS 2GB SS Mach Xtreme C2S46D30-D313 - - • • • MICRON MT8JTF25664AZ-1G4M1 2GB SS MICRON D9PFJ - - • • • Patriot PSD32G13332 2GB DS Prtriot PM128M8D3BU-15 9 - • • RiDATA C304627CB1AG22Fe 2GB DS RiDATA C304627CB1AG22Fe 9 - • • • RiDATA E304459CB1AG32Cf 4GB DS RiDATA E304459CB1AG32Cf 9
1.2.5 擴展插槽 第一章 安裝或卸除任何擴展卡之前,請暫時先將電腦的電源線拔出。如此可免 除因電氣殘留於電腦中而發生的意外狀況。 插槽編號 插槽說明 1 PCIe 2.0 x1_1 插槽 2 PCIe 3.0/2.0 x16_1 插槽 3 PCIe 2.0 x1_2 插槽 4 PCIe 3.0/2.0 x16_2 插槽 5 PCIe 2.0 x1_3 插槽 6 PCIe 2.0 x16_3 插槽 華碩 SABERTOOTH Z97 MARK 1/USB 3.
PCI Express 運行模式 PCIe x16_3 設置 第一章 PCIe x16_3 PCIe x1_3 Rear USB 3.
1.2.6 主板上的內置按鈕與開關 1. MemOK! 按鈕 在主板上安裝不兼容的內存條可能會導致啟動失敗,而且在 MemOK 按鈕旁的 DRAM_LED 指示燈也會一直亮著。按住 MemOK! 按鈕直到 DRAM_LED 指示燈 開始閃爍,即開始自動將內存調整為兼容直到成功啟動。 • 請參考 1.2.8 內置指示燈 來找到 DRAM_LED 更精確的位置。 • D R A M_L E D 指示燈在內存沒有正確安裝時也會亮起,在使用 MemOK! 功能前,請先關閉系統並重新安裝內存。 • MemOK! 按鈕在 Windows 操作系統下無法使用。 • 在調整過程中,系統會載入與測試故障安全防護內存設置。系統進行 一項故障安全防護設置測試約需要 30 秒的時間,若是測試失敗,系 統會重新啟動並測試下一個項目。DRAM_LED 指示燈閃爍的速度增 加表示正在運行不同的測試過程。 • 由於內存調整需求,系統將於每一組設置值測試時重新啟動。在經過 整個調整過程後若安裝的內存仍然無法啟動,DRAM_LED 指示燈會 持續亮著,請替換為用戶手冊中或華碩網站(www.asus.com.
1.2.7 跳線選擇區 CMOS 配置數據清除(3-pin CLRTC) 第一章 在主板上的 CMOS 內存中記載著正確的時間與系統硬件配置等數據,這些數據並 不會因電腦電源的關閉而遺失數據與時間的正確性,因為這個 CMOS 的電源是由主 板上的鋰電池所供應。 想要清除這些數據,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 將 CLRTC 跳線帽由 [1-2](默認值)改為 [2-3] 約五∼十秒鐘(此時即清 除 CMOS 數據),然後再將跳線帽改回 [1-2]。 3. 插上電源線,開啟電腦電源。 4. 當啟動步驟正在進行時按著鍵盤上的 鍵進入 BIOS 程序畫面重新設 置 BIOS 數據。 除了清除 CMOS 配置數據之外,請勿將主板上 CLRTC 的跳線帽由默認 值的位置卸除,因為這麼做可能會導致系統啟動失敗。 • 若上述步驟無效,請卸除主板上的內置電池並再次卸除跳線帽以清除 CMOS 配置數據。在 CMOS 配置數據清除後,再重新裝回電池。 • 如果您是因為超頻的緣故導致系統無法正常啟動,您無須使用上述的 配置數據清除方式來排除問題。建議可以採用 C.
2. CPU 超壓設置(3-pin CPU_OV) 第一章 這個跳線帽可讓您依照安裝的處理器類型,設置較高的處理器電壓以獲得更有 彈性的超頻系統。若要獲得更多的處理器電壓,將跳線帽針腳設為 2-3,若要恢 復默認的處理器電壓設置,將跳線帽針腳移回 1-2 的位置。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
1.2.8 內置 LED 指示燈 1.
1.2.9 內部連接端口 這些插槽可支持使用 Serial ATA 6.0 Gb/s 排線來連接 Serial ATA 6.0 Gb/s 硬盤。 若您安裝了 Serial ATA 硬盤,您可以通過 Intel® Rapid Storage 技術,與內置 的 Intel® Z97 芯片組來創建 RAID 0、RAID 1、RAID 5、RAID 10 磁盤陣列。 將 SATA 數據線上的直角接口端 (right angle side)連接在 SATA 設備上,或是將直角接口端安裝至 主板內置的 SATA 連接端口,以避 免造成與較大顯卡的衝突。 ‧ 這些插槽的默認值為 [AHCI Mode],若您想要使用這些插槽來建構 Serial ATA RAID 功能,請將 BIOS 程序中的 SATA Mode 項目設置 為 [RAID Mode]。請參考 3.6.3 SATA 設置(SATA Configuration) 一節的詳細說明。 • 在創建 RAID 磁盤陣列之前,請先參考 5.
2. ASMedia® Serial ATA 6.0 Gb/s 插槽(7-pin SATA6G_E1-E2 [米色]) 這些插槽可支持使用 Serial ATA 6.0 Gb/s 排線來連接 Serial ATA 6.0 Gb/s 硬盤。 第一章 ‧ ASMedia 保存控制器僅支持 AHCI 模式。 ‧ 這些 SATA 插槽只能連接數據硬盤。 3. USB 3.0 連接插槽(20-1 pin USB3_34) 這個插槽用來連接 USB 3.0 模塊,可在前面板或後側連接端口擴展 USB 3.0 模塊。當您安裝 USB 3.0 模塊,您可以享受 USB 3.0 的益處,包括有更快的數 據傳輸率最高達 5Gbps、對可充電的 USB 設備更快的充電速度、最佳化能源效 率,以及與 USB 2.0 向下兼容。 • USB 3.0 模塊為選購配備,請另行購買。 • 這些插槽是以 xHCI 規格為基礎,建議您在 Windows® 7 或更新版的 Windows® 操作系統中安裝相關的驅動程序以完整使用 USB 3.
3. 數字音頻連接排針(4-1 pin SPDIF_OUT) 第一章 這組排針是用來連接 S/PDIF 數字音頻模塊,您可以利用這組排針以 S/PDIF 音頻數據線連接到音頻設備的數字音頻輸出端,使用數字音頻輸出來代替常規的 模擬音頻輸出。 S/PDIF 模塊為選購配備,請另行購買。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
5. USB 2.0 連接插槽(10-1 pin USB1112, USB1314) 這些 USB 擴展套件排線插槽支持 USB 2.0 規格,將 USB 模塊排線連接至任 何一個插槽,然後將模塊安裝到機箱後側面板中開放的插槽。這些 USB 插槽與 USB 2.0 規格兼容,並支持傳輸速率最高達 480Mbps。 第一章 請勿將 1394 排線連接到 USB 插槽上,這麼做可能會導致主板的損毀。 若是您的機箱擁有前面板 USB 連接端口,您可以將前面板 USB 排線連 接至 ASUS Q-Connector(USB),然後將 Q-Connector(USB)安裝 至主板內置的 USB 插槽上。 USB 2.
6.
7. 前面板音頻連接排針(10-1 pin AAFP) 這組音頻外接排針供您連接到前面板的音頻排線,除了讓您可以輕鬆地通過主 機前面板來控制音頻輸入/輸出等功能,並且支持 AC’97 或 HD Audio 音頻標 準。將前面板音頻輸出/輸入模塊的連接排線之一端連接到這個插槽上。 第一章 • 建議您將支持高保真(high definition)音頻的前面板音頻模塊連接 到這組排針,如此才能獲得高保真音頻的功能。 • 若是要將高保真音頻前面板模塊安裝至本接針,請將 B I O S 程序中 Front Panel Type 項目設置為 [HD];若要將 AC 97 音頻前面版模塊 安裝至本接針,請將 BIOS 程序設置為 [HD] 或 [AC97]。 8.
9. 主板電源插槽(24-pin EATXPWR, 8-pin EATX12V) 第一章 這些電源插槽用來連接一個 ATX +12V 電源。電源所提供的連接插頭已經過 特別設計,只能以一個特定方向插入主板上的電源插槽。找到正確的插入方向 後,僅需穩穩地將之套進插槽中即可。 • 建議您使用與 2.0 規格的 24-pin ATX 12V 兼容的電源(PSU), 才能提供至少 350W 高功率的電源,以供應系統足夠的電源需求。 • 請務必連接 4-pin/8-pin EATX12V 電源插頭,否則系統可能無法順 利啟動。 ‧ 如果您想要安裝其他的硬件設備,請務必使用較高功率的電源以提供 足夠的設備用電需求。若電源無法提供設備足夠的用電需求,則系統 將會變得不穩定或無法開啟。 ‧ 若是您想要安裝二張或更多的高級 PCI Express x16 顯卡,請使用 1000 瓦以上的電源以確保運行穩定。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
10.
11. TPM 插座(20-1 pin TPM) 第一章 這個插座支持可信任安全平台模塊(T P M)系統,用來安全地保存金鑰、數 字認證、密碼和數據。可信任安全平台模塊(TPM)系統也用來協助加強網絡安 全,保護數字身分,以及確保平台的安全性。 12. DirectKey 連接端口(2-pin DRCT) 這個連接端口用來連接機箱上的按鈕來支持使用 DirectKey 功能。將機箱上支 持本功能按鈕之排線,從機箱連接至主板。 請確認您的機箱配備有支持本功能之排線,請參考機箱的用戶手冊來獲 得詳細的說明。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
13.
第二章 2.1 創建您的電腦系統 2.1.1 安裝主板 本章節的圖標僅供參考,主板的結構可能會隨著型號而有所不同,但是 安裝的步驟仍然是相同的。 1. 安裝華碩 Q-Shield 擋板至機箱的後側 I/O 面板。 2. 將主板放入機箱,並確認後側 I/O 連接端口對齊機箱的後側 I/O 面板。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
3.
2.1.2 安裝中央處理器 第二章 本插槽僅支持 LGA1150 處理器,請確認並安裝正確的處理器,請勿將 LGA1155 與 LGA1156 處理器安裝於 LGA1150 插槽。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
2.1.
第二章 取出散熱片與風扇 華碩 SABERTOOTH Z97 MARK 1/USB 3.
2.1.
第二章 2.1.5 安裝 ATX 電源 或 或 華碩 SABERTOOTH Z97 MARK 1/USB 3.
2.1.
2.1.7 安裝前面板輸出/輸入連接端口 PWR Ground Reset Ground HDD LED R SW POWE RESET SW 第二章 HDD LED+ HDD LED- HDD LED 安裝 ASUS Q-Connector 安裝 USB 2.0 連接插槽 安裝前面板音頻連接插槽 AAFP USB 2.0 安裝 USB 3.0 連接插槽 USB 3.0 華碩 SABERTOOTH Z97 MARK 1/USB 3.
2.1.
2.2 BIOS 更新應用程序 USB BIOS Flashback USB BIOS Flashback 提供最簡單更新 BIOS 的方法。用戶可以輕鬆嘗試使用新的 BIOS 版本來進行超頻,不需要進入 BIOS 或操作系統,只要插入 USB 存儲設備然後 按下 BIOS Flashback 按鈕三秒鐘,BIOS 程序就會自動在待機狀態下更新。 請依照以下步驟使用 USB BIOS Flashback: 1. 將包裝盒內附的驅動程序與應用程序 DVD 光盤放入光驅,然後安裝 USB BIOS Flashback 安裝向導。請依照屏幕指示的步驟來完成程序的安裝。 2. 將 USB 存儲設備插入 USB Flashback 連接端口。 • 建議您使用 USB 2.0 存儲設備來保存最新的 BIOS,可以獲得更好的 兼容性與穩定性。 3. 啟動 USB BIOS Flashback 安裝向導來自動下載最新的 BIOS。 4. 按下 BIOS Flashback 按鈕約三秒鐘直到指示燈開始閃爍,表示 BIOS Flashback 功能已經啟動。 5.
2.3 主板後側與音頻連接端口 2.3.1 後側面板連接端口 第二章 後側面板連接端口 1. USB 2.0 連接端口 7-10 6. HDMI 連接端口 2. DisplayPort 連接端口 7. USB 3.0 連接端口 5-6,支持 ASUS USB 3.0 Boost 底端連接端口支持 USB BIOS Flashback 和 USB Charger+ 3. LAN(RJ-45)網絡連接* 8. USB 3.1 連接端口 E1-E2 4. LAN(RJ-45)網絡連接* 9. 音頻輸出/輸入接口** 5.
• USB 3.1/3.0 設備只能用來作為數據磁盤。 • 強烈建議您將 USB 3.1 設備連接至 USB 3.1 連接端口、USB 3.0 設 備連接至 USB 3.0 連接端口,才能讓您的 USB 設備獲得更快更好的 性能表現。 • 由於 Intel® 9 系列芯片組的設計,所有連接至 USB 2.0 與 USB 3.
2.3.2 音頻輸出/輸入連接圖標說明 音頻輸出/輸入連接端口 橘色 淺藍色 黑色 草綠色 粉紅色 連接耳機與麥克風 第二章 連接立體聲喇叭 連接 2.
連接 4.1 聲道喇叭 第二章 連接 5.1 聲道喇叭 連接 7.1 聲道喇叭 華碩 SABERTOOTH Z97 MARK 1/USB 3.
2.4 第一次啟動電腦 1. 確認所有排線與接腳都接妥,然後蓋上機箱的外蓋。 2. 確定所有的開關都已關閉 3. 將電源線接上機箱背面的電輸入插座。 4. 情況許可的話,最好將電源線路上加接突波吸收/保護器。 5. 您可以先開啟以下周邊的電源: a. 顯示屏 b. 外接式 SCSI 接口外圍設備(從串連的最後端開始) c. 系統電源(ATX 的電源不會因為送電而馬上動作,而是等待面板上的按鈕 動作後才會工作) 第二章 6.
第三章 3.
3.
3.2.1 EZ Mode 本主板的 BIOS 設置程序的默認值為 EZ Mode。您可以在 EZ Mode 中查看系統 基本數據,並可以選擇顯示語言、喜好設置及啟動設備順序。若要進入 Ad vanced Mode,請點擊畫面右下角 Advanced Mode,或是按下 快捷鍵。 進入 BIOS 設置程序的畫面可個人化設置,請參考 3.
3.2.
功能表列 BIOS 設置程序最上方各菜單功能說明如下: My Favorites 本項目將記錄時常使用的系統設置及設置值。 Main 本項目提供系統基本設置。 Ai Tweaker 本項目提供超頻設置。 Advanced 本項目提供系統高級功能設置。 Monitor 本項目提供溫度、電源及風扇功能設置。 Boot 本項目提供啟動磁盤設置。 Tool 本項目提供特殊功能設置。 Exit 本項目提供退出 BIOS 設置程序與出廠默認值還原功能。 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,即選擇 M a i n 菜單所出現的項 目。 點擊菜單中的其他項目(例如:Ai Tweaker、Advanced、Monitor、Boot 與 Exit)也會出現該項目不同的選項。 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記,代表此為子菜單,您可利用 方向鍵來選擇,並按下 鍵來進入子菜單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程序界面顯示的語言。點擊這個按 鈕來選擇您想要的 BIOS 畫面顯示語言。 第三章 我的最愛(F3) 這個按鈕位在
快速筆記(F9) 按下此按鈕,可讓您針對已在 BIOS 中進行的設置輸入筆記。 • 快速筆記不支持以下鍵盤功能:刪除、剪下、複製與貼上。 • 您只能使用英文字母與數字來輸入筆記。 快捷鍵 這個按鈕位在功能表列的上方,包含有 BIOS 程序設置的導引方向鍵,使用箭頭按 鍵來選擇菜單中的項目並更改設置。 滾動條 在菜單畫面的右方若出現滾動條,即代表此頁選項超過可顯示的畫面,您可利用上 /下方向鍵或是 PageUp/PageDown 鍵來切換畫面。 在線操作說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。使用 按鍵來抓取 BIOS 屏幕畫面,並保存至攜帶式存儲設備。 設置值 此區域顯示菜單項目的設置值。這些項目中,有的功能選項僅為告知用戶當前運行 狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方向鍵 移動項目時,被選擇的項目以反白顯示。 設置值被選擇後以反白顯示。要改變設置值請選擇此項目,並按下 鍵以顯 示設置值列表。 上次修改的設置按鈕 按下此按鈕可查看您在 BIOS 設置中上一次所做的修改項目。 第三章
3.2.3 QFan Control Q F a n C o n t r o l 用來設置風扇設置文件,或手動設置處理器與機箱風扇的運行速 度。 選擇要應用至風 扇的設置文件 點擊以啟動 PWM 模式 點擊以啟動 DC 模式 第三章 點擊來選擇要 設置的風扇 點擊以應用風扇設置 點擊以恢復更改 點擊回到主菜單 選擇手動設置風扇 華碩 SABERTOOTH Z97 MARK 1/USB 3.
手動設置風扇 從設置文件清單中選擇 Manual 來手動設置風扇運行的速度。 速度點 點擊或輕觸以手動設置風扇 第三章 請依照以下步驟設置風扇: 1. 選擇想要設置的風扇並查看該風扇現在的狀況。 2. 點擊並拖曳速度點來調整風扇的運行速度。 3.
3.2.4 EZ Tuning 向導 EZ Tuning 向導用來超頻處理器和內存條、電腦使用與處理器風扇至最佳設置。通 過這個功能您也可以輕鬆設置系統的 RAID 功能。 系統超頻設置 RAID 設置 第三章 調整系統設置 請依照以下步驟調整設置: 1. 在鍵盤按下 鍵或在 B I O S 程序畫面中點擊 Tuning 向導窗口,然後點擊 下一步(Next)。 來啟動 E Z 2. 選擇電腦狀態為 Daily Computing 或 Gaming/Media Editing,然後點擊 下一步 (Next)。 3. 選擇安裝的處理器風扇類型(Box cooler、Tower cooler 或 Water cooler)然後 點擊 下一步(Next)。 若是無法確定處理器風扇類型,點擊 我不確定(I’m not sure),系統 將會自動檢測處理器風扇類型。 4. 點擊 下一步(Next) 然後點擊 確定(Yes) 來確認自動調整。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
3.
新增項目至我的最愛 請依照以下步驟新增項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程序畫面中點擊 圖畫面。 來啟動設置樹狀 2. 在設置樹狀圖畫面中選擇想要保存至我的最愛的 BIOS 項目。 主菜單面板 已選擇的快 捷方式項目 子菜單面板 3. 從主菜單面板選擇項目,然後點擊子菜單中想要保存至我的最愛的選項,再點擊 或輕觸 或是按下 按鍵。 • 有子菜單的項目。 • 用戶自訂項目,例如:語言、啟動設備順序。 • 設置項目,例如:內存 SPD 信息、系統時間與日期。 4. 點擊 Exit (ESC) 或按下 鍵來關閉樹狀圖窗口。 5. 到我的最愛菜單查看已保存的 BIOS 項目。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
3.4 主菜單(Main Menu) 當您進入 BIOS 設置程序的高級模式(Advanced Mode)時,首先出現的第一個 畫面即為主菜單。主菜單顯示系統信息概要,用來設置系統日期、時間、語言與安全 設置。 安全性菜單(Security) 本菜單可讓您改變系統安全設置。 第三章 • 若您忘記設置的 BIOS 密碼,可以採用清除 CMOS 實時鐘(RTC) 內存。請參考 1.2.6 主板上的內置開關 一節的說明。 • Administrator 或 User Password 項目默認值為 Not Installed,當您 設置密碼之後將顯示為 Installed.
系統管理員密碼(Administrator Password) 當您設置系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設置程序中的某 些信息無法查看或更改設置。 設置系統管理員密碼 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 窗口輸入欲設置的密碼,輸入完成按下 。 3. 請再一次輸入密碼以確認密碼正確。 更改系統管理員密碼 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
3.
Ai Overclock Tuner [Auto] 本項目可以讓您設置 CPU 的超頻選項來達到您所想要的 CPU 外頻。請選擇以下 任一種默認的超頻選項: [Auto] 載入系統最佳化設置值。 [Manual] 自動最佳化處理器比值與 BCLK 頻率。 以下項目只有在 Ai Overclock Tuner 設置為 [Manual] 時才會出現。 CPU Strap [Auto] 本項目提供您選擇一個接近目標 B C L K(基本時鐘)的 s t r a p,或按照原本 設置為 [Auto] 來讓 BIOS 自動決定。設置值有:[Auto] [100MHz] [125MHz] [166MHz] [250MHz]。 以下項目只有在 CPU Strap 設置為 [100MHz]、[125MHz]、[166MHz] 或 [250MHz] 時才會出現。 Source Clock Tuner [Auto] 本項目用來依照指派的 CPU strap 選擇來源時鐘以獲得更好的超頻能力。 設置值有:[8Ohm dbl] [7Ohm dbl] [6Ohm dbl] [5Ohm dbl] [4Ohm dbl] [3O
ASUS MultiCore Enhancement [Auto] [Auto] 通過華碩核心比率的設置,可以獲得最佳超頻性能的最大值。 [Disabled] 本項目用來設置默認的核心比率。 CPU Core Ratio [Per Core] 本項目用來設置 CPU 比值與自動同步。設置值有:[Auto] [Sync All Cores] [Per Core]。 CPU Core Ratio 設置為 [Per Core] 時會出現以下項目: 1-Core Ratio Limit [Auto] [Auto] 選擇並應用 CPU 默認的 Turbo 倍頻設置。 [Manual] 選擇手動指定 1-Core Ration Limit 數值高於或等於 2-Core Ratio Limit。 2-Core Ratio Limit [Auto] [Auto] 選擇並應用 CPU 默認的 Turbo 倍頻設置。 [Manual] 選擇手動指定 2-Core Ration Limit 數值高於或等於 3-Core Ratio Limit。 若您要設置 2-Core Ratio Limit 數值,請
Internal PLL Overvoltage [Auto] 本項目用來設置 Internal PLL 電壓,讓 K 型號的處理器能獲得最大的超頻性能。 設置值有:[Auto] [Enabled] [Disabled]。 BCLK Frequency : DRAM Frequency Ratio [Auto] 本項目用來設置 BCLK 頻率到內存頻率比值。 [Auto] 內存速率設為最優化設置。 [100:133] BCLK 頻率到內存頻率比為 100:133。 [100:100] BCLK 頻率到內存頻率比為 100:100。 DRAM Frequency [Auto] 本項目可讓您設置內存的運行頻率。設置選項會隨著 BCLK Frequency 設置值 變動。設置值有:[DDR3-800MHz] [DDR3-1066MHz] [DDR3-1333MHz] [DDR31400M H z] [D D R3-1600M H z] [D D R3-1800M H z] [D D R3-1866M H z] [D D R32000M H z] [D D R3-2133M H z] [D D R
DRAM Timing Control 本項目可讓您設置 DRAM timing 控制功能,您可以使用 <+> 與 <-> 鍵調整數值。 當您要恢復默認值時,請使用鍵盤輸入 並按下 鍵。 自行更改數值將會導致系統的不穩定與硬件損毀,當系統出現不穩定的 狀況時,建議您使用默認值。 Primary Timings DRAM CAS# Latency [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# to CAS# Delay [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# PRE Time [Auto] 設置值有:[Auto] [1] – [31]。 DRAM RAS# ACT Time [Auto] 設置值有:[Auto] [1] – [63]。 DRAM COMMAND Mode [Auto] 設置值有:[Auto] [1] – [3]。 第三章 Secondary Timings DRAM RAS# to RAS# Delay [Auto] 設置值有:[Auto] [1] – [15]。 DRAM REF
Third Timings tRDRD [Auto] 設置值有:[Auto] [1] – [7]。 tRDRD_dr [Auto] 設置值有:[Auto] [1] – [15]。 tRDRD_dd [Auto] 設置值有:[Auto] [1] – [15]。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
tWRRD [Auto] 設置值有:[Auto] [1] – [63]。 tWRRD_dr [Auto] 設置值有:[Auto] [1] – [15]。 tWRRD_dd [Auto] 設置值有:[Auto] [1] – [15]。 tWRWR [Auto] 設置值有:[Auto] [1] – [7]。 tWRWR_dr [Auto] 設置值有:[Auto] [1] – [15]。 tWRWR_dd [Auto] 設置值有:[Auto] [1] – [15]。 Dec_WRD [Auto] 設置值有:[Auto] [0] – [1]。 tRDWR [Auto] 設置值有:[Auto] [1] – [31]。 tRDWR_dr [Auto] 設置值有:[Auto] [1] – [31]。 tRDWR_dd [Auto] 設置值有:[Auto] [1] – [31]。 MISC MRC Fast Boot [Auto] 第三章 本項目用來啟動或關閉 MRC fast boot 功能。設置值有:[Auto] [Enable] [Disable]。 DRAM CLK Period [Auto] 設
Skew Control 調整這些項目可以提升內存的超頻兼容性與穩定性。 Transmitter Rising Slope [Auto] 設置值有:[Auto] [0] – [31]。 Transmitter Falling Slope [Auto] 設置值有:[Auto] [0] – [31]。 Transmitter Control Time [Auto] 設置值有:[Auto] [0] – [31]。 Receiver Rising Slope [Auto] 設置值有:[Auto] [0] – [31]。 Receiver Falling Slope [Auto] 設置值有:[Auto] [0] – [31]。 Receiver Control Time [Auto] 設置值有:[Auto] [0] – [31]。 External DIGI+ Power Control CPU Load-Line Calibration [Auto] Load-line 是根據 Intel 所訂立之 VRM 規格,其設置值將影響 CPU 電壓。CPU 運行電壓將依 CPU 的負載呈比例性遞減,當您將此項目的設置值設
以下項目只有在 CPU VRM Switching Frequency 設置為 [Manual] 時才 會出現。 Fixed CPU VRM Frequency (KHz) [300] 本項目可讓您設置固定的 VRM 頻率。請使用 <+> 與 <-> 鍵調整數值。數 值以 50kHz 為間隔,更改的範圍由 300kHz 至 500kHz。 VRM Spread Spectrum [Disabled] 本項目可讓您啟動 VRM Spread Spectrum 項目以增加系統穩定性。設置值 有:[Enable] [Disable]。 Active Frequency Mode [Disabled] 本項目可讓您啟動 Active Frequency Mode 項目以增強省電性能。設置值有: [Enable] [Disable]。 CPU Power Phase Control [Auto] 本項目用來依照 CPU 的需求控制電源相數。設置值有:[Auto] [Standard] [Optimized] [Extreme] [Powe Phase Response]。 當本項目設置為 [Powe Phase
CPU Power Thermal Control [120] 較高的溫度帶給 CPU 電力更大的散熱範圍,並擴展超頻容忍度來增加超頻的 潛力。使用 <+> 與 <-> 按鍵調整數值,數值會依照安裝的處理器而異。 請勿將散熱系統卸除,散熱環境需受到監控。 DRAM Current Capability [100%] 較高的數值提供更大的總電力範圍,同時擴展超頻頻率的範圍。設置值有: [100%] [110%] [120%] [130%]。 DRAM Switching Frequency [Auto] 本項目用來調整內存切換頻率。指派固定的高內存頻率來增加超頻的範圍,或 低內存頻率以獲得較佳的系統穩定度。設置值有:[Auto] [Manual]。 以下項目只有在 DRAM Switching Frequency 設置為 [Manual] 時才會出 現。 Fixed DRAM Switching Frequency (KHz) [300] 本項目用來設置固定的內存頻率。使用 <+> 與 <-> 鍵調整數值,設置值以 50kHz 為間隔,更改的範圍從 300kHz 至 500kHz。 [Auto] 設置
Turbo Mode [Enabled] 本項目用來設置核心處理器的速度,使其在運行電力、電流與溫度條件限制 下,可以比基本運行頻率更快的速度運行。設置值有:[Enabled] [Disabled]。 以下項目只有在 Turbo Mode 設置為 [Enabled] 時才會出現。 Turbo Mode 參數 Long Duration Package Power Limit [Auto] 本項目用來設置渦輪倍頻(turbo ratio)的瓦數,默認值為散熱設計功率 (thermal design power)。請使用 <+> 與 <-> 鍵調整數值,數值更改的範 圍為 1W 至 4096W。 Package Power Time Window [Auto] 本項目用來設置渦輪倍頻(turbo ratio)維持的時間長度。請使用 <+> 與 <-> 鍵調整數值,數值更改的範圍為 1 至 127 秒。 Short Duration Package Power Limit [Auto] 本項目用來設置渦輪倍頻(turbo ratio)的更高瓦數來提供系統保護,默 認值為 long duration limit 的
CPU Internal Power Configuration CPU Integrated VR Efficiency Management [Auto] 本項目可使處理器處於低電源狀態時提升節能性能。關閉此項目可使全 集成電壓調節器總是以高性能運行。設置值有:[A u t o] [H i g h P e r f o r m a n c e] [Balanced]。 Power Decay Mode [Auto] 當處理器進入低電流狀態時,允許系統提升全集成電壓調節器的節能模式。設 置值有:[Auto] [Disabled] [Enabled]。 Idle Power-in Response [Auto] 當全集成電壓調節器進入手動覆寫模式時,允許您設置它的電壓轉換速率。設 置值有:[Auto] [Regular] [Fast]。 Idle Power-out Response [Auto] 當全集成電壓調節器離開手動覆寫模式時,允許您設置它的電壓轉換速率。設 置值有:[Auto] [Regular] [Fast]。 Power Current Slope [Auto] 本項目用來設置瞬時載入時的
Power Saving Level 2 Threshold [Auto] 較低的設置值可提供充足的超頻範圍,以提升超頻潛能。而較高的設置值可提 供較好的節能性。請使用 <+> 與 <-> 鍵調整數值,設置值以 1Amp 為間隔,更 改的範圍從 0A 至 50A。 Power Saving Level 3 Threshold [Auto] 較低的設置值可提供充足的超頻範圍,以提升超頻潛能。而較高的設置值可提 供較好的節能性。請使用 <+> 與 <-> 鍵調整數值,設置值以 1Amp 為間隔,更 改的範圍從 0A 至 30A。 Extreme Over-Voltage [Disabled] 關閉本項目可以保護處理器不因過高的電壓而燒毀。當啟動本項目時,您可以 選擇較高層級的電壓來進行超頻,但可能會降低處理器的使用壽命。設置值有: [Disabled] [Enabled]。 只有在內置的 OC_CPU 跳線帽設置為 ON 時才能將本項目設置為啟動。 請參考 1.2.
以下項目只有在 CPU Cache Voltage 設置為 [Manual Mode] 時才會出 現。 CPU Cache Voltage Override [Auto] 本項目用來設置處理器緩存電壓覆寫。默認值為依照安裝的處理器所得的標準 數值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間隔,更改的範圍從 0.001V 至 1.920V。 以下項目只有在 CPU Core Voltage 設置為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] [+] 設置正數值偏移電壓。 [–] 設置負數值偏移電壓。 CPU Cache Voltage Offset 本項目用來設置 CPU Cache Voltage Offset。默認值為依照安裝的處理 器所得的標準數值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間 隔,更改的範圍從 0.001V 至 0.
SVID Support [Auto] 當系統超頻時將本項目設置為 [Enabled]。關閉 SVID 支持以中斷處理器與外接電 壓調節器的連線。設置值有:[Auto] [Disabled] [Enabled]。 以下項目只有在 SVID Support 設置為 [Enabled] 時才會出現。 SVID Voltage Override [Auto] 本項目用來設置 S V I D 電壓覆寫。默認值為依照安裝的處理器所得的標準數 值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.001V 為間隔,更改的範圍從 0.001V 至 2.440V。 CPU Input Voltage [Auto] 本項目用來設置處理器的輸入電壓。默認值為依照安裝的處理器所得的標準數值。 請使用 <+> 與 <-> 鍵調整數值,設置值以 0.010V 為間隔,更改的範圍從 0.800V 至 3.040V。 DRAM Voltage [Auto] 本項目用來設置內存電壓。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.005V 為 間隔,更改的範圍從 1.20V 至 1.
DRAM CTRL REF Voltage [Auto] 本項目用來設置內存控制參考電壓。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.00500x 為間隔,更改的範圍從 0.39500x 至 0.63000x。 若要設置 D R A M 內存參考電壓的數值,建議您設置接近標準值 0.500000x 的數值。 DRAM DATA REF Voltage on CHA/CHB [Auto] 本項目用來設置在通道 A 與 B 的內存控制參考電壓。請使用 <+> 與 <-> 鍵調整數 值,設置值以 0.00500x 為間隔,更改的範圍從 0.39500x 至 0.63000x。 若要設置 D R A M 內存參考電壓的數值,建議您設置接近標準值 0.500000x 的數值。 Clock Crossing Voltage [Auto] 本項目用來設置當 BCLK DN 上緣等於 BCLK DP 下緣時,時鐘交叉電壓的啟動 值。請使用 <+> 與 <-> 鍵調整數值,設置值以 0.00625V 為間隔,更改的範圍從 0.1V 至 1.
3.
3.6.1 處理器設置(CPU Configuration) 本項目可讓您得知中央處理器的各項信息與更改中央處理器的相關設置。 Intel Adaptive Thermal Monitor [Enabled] 本項目通過處理器到達溫度調節點時降低頻率來保護處理器。溫度監控包括有 TM1(溫度監控 1)、TM2(溫度監控 2)與 EMTTM(增強多段式溫度監控)。設 置值有:[Disabled] [Enabled]。 Hyper-Threading [Enabled] 啟動本項目可以讓高速運行緒處理器在操作系統內作為兩個邏輯處理器,允許操作 系統同時處理二個運行緒或處理器。 Active Processor Cores [All] 本項目用來設置在每個處理封包中啟用的處理器核心數量。設置值有:[All] [1] [2] [3]。 Limit CPUID Maximum [Disabled] [Enabled] 本項目可以讓系統無處理器 CPUID 功能支持時亦可正常啟動。 [Disabled] 關閉此功能。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
Execute Disable Bit [Enabled] 啟動此選項來保護系統免於遭到某些病毒或惡意軟件的攻擊。設置值有: [Disabled] [Enabled]。 Intel Virtualization Technology [Disabled] [Enabled] 啟動 Intel 虛擬技術(Virtualization Technology)讓硬件平台可以同 時運行多個操作系統,將一個系統平台虛擬為多個系統。 [Disabled] 關閉此功能。 Hardware Prefetcher (L2 Cache) [Enabled] [Enabled] 本項目可以讓硬件平台獨立和同步運行多重操作系統。 [Disabled] 關閉此功能。 Adjacent Cache Line Prefetch [Enabled] [Enabled] 本項目可以讓硬件平台運行 Adjacent Cache Line Prefetch 功能。 [Disabled] 關閉此功能。 Boot Performance Mode [Max Non-Turbo Performance] 本項目用來
CPU states [Auto] 本項目用來設置 C P U s t a t e s 的電源節能。設置值有:[A u t o] [D i s a b l e d] [Enabled]。 以下項目只有在 CPU states 設置為 [Enabled] 時才會出現。 Enhanced C1 state [Enabled] 本項目可以讓處理器在閒置時降低電力消耗。設置值有:[E n a b l e d] [Disabled]。 CPU C3 Report [Enabled] 本項目可以讓您啟動或關閉 C P U C3 報告給操作系統。設置值有: [Enabled] [Disabled]。 CPU C6 Report [Enabled] 本項目可以讓您啟動或關閉 C P U C6 報告給操作系統。設置值有: [Enabled] [Disabled]。 C6 Latency [Short] 本項目可以讓您設置 C6 s t a t e 的 C6 延遲期間。設置值有:[S h o r t] [Long]。 CPU C7 Report [CPU C7s] 本項目可以讓您啟動或關閉 C P U C7 報告給操作系統。設置
3.6.2 PCH 設置(PCH Configuration) PCI Express Configuration 本項目用來管理與設置 PCI Express 插槽。 PCIe Speed [Auto] 本項目用來讓系統自動選擇 PCI Express 連接端口速度。設置為 [Gen1] 時, PCI-E 連接端口會以 PCI-E 1.0 速度運行。設置為 [Gen2] 時,PCI-E 連接端口會 以 PCI-E 2.
Hybrid Hard Disk Support [Disabled] 本項目用來啟動或關閉混合磁盤功能。設置值有:[Enabled] [Disabled]。 Intel Smart Connect Technology [Disabled] 本項目用來讓系統支持 Intel Smart Connect Technology,當系統進入睡眠模式時 會定期更新選定的應用程序。設置值有:[Enabled] [Disabled]。 3.6.
SATA Mode Selection [AHCI] 本項目可設置 SATA 硬件設備的相關設置。 [Disabled] 關閉 SATA 功能。 [IDE] 若要將 Serial ATA 作為 Parallel ATA 物理保存接口,請將本項目設 置為 [IDE]。 [AHCI] 若要 Serial ATA 硬件設備使用 Advanced Host Controller Interface (AHCI) 模式,請將本項目設置為 [AHCI]。AHCI 模式可讓內置的存 儲設備啟動高級的 Serial ATA 功能,通過原生命令排序技術來提升 工作性能。 [RAID] 若要在 Serial ATA 硬盤設置 RAID 磁盤陣列,請將本項目設置為 [RAID]。 以下項目只有在 SATA Mode Selection 設置為 [RAID] 時才會出現。 Pcie Nand Configuration [Auto] 本項目用來啟動或關閉 PCIe NAND。設置值有:[Disabled] [Enabled]。 Aggressive LPM Support [Disabled] 本項目為 L
3.6.4 系統代理設置(System Agent Configuration) Graphics Configuration 本項目用來選擇以 CPU 或 PCIe 顯示設備作為優先使用的顯示設備。 Primary Display [Auto] 本項目用來選擇以 iGPU 或 PCIe 顯示設備作為優先使用的顯示設備。設置值 有:[Auto] [CPU Graphics] [PCIE]。 CPU Graphics Memory [Auto] 本項目用來授權給集成性和獨立顯示設備作為多重顯示屏輸出使用。處理器 繪圖顯示共享系統內存固定為 64 MB。設置值有:[Auto] [32M] [64M] [96M] [128M] [160M] [192M] [224M] [256M] [288M] [320M] [352M] [384M] [416M] [448M] [480M] [512M] 。 DMI Configuration DMI Gen 2 [Auto] 設置為 [Enabled] 時,DMI 會以 PCI-E 2.
3.6.5 USB 設備設置(USB Configuration) 本菜單可讓您更改 USB 設備的各項相關設置。 在 USB Devices 項目中會顯示自動檢測到的數值或設備。若無連接任何 設備,則會顯示 None。 Legacy USB Support [Enabled] [Enabled] 啟動在常規操作系統中支持 USB 設備功能。 [Disabled] USB 設備只能在 BIOS 程序設置中使用,無法在啟動設備列表中被檢 測到。 [Auto] 系統可以在啟動時便自動檢測是否有 USB 設備存在,若是,則啟動 USB 控制器。 第三章 Intel xHCI Mode [Smart Auto] [Auto] 當操作系統安裝有 xHCI 驅動程序,xHCI 會自動啟動並以 USB 3.0 模式運行。 [Smart Auto] xHCI 驅動程序在系統自我檢測(POST)過程中與操作系統中都支持 USB 3.
Mass Storage Devices [Auto] 本項目用來讓系統依照硬件格式檢測設備。設置值有:[Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM]。 USB Single Port Control 本項目用來啟動或關閉個別 USB 連接端口。 USB 連接端口的位置請參考 1.2.2 主板結構圖 的說明。 3.6.
PCH - PCI Express 選項 DMI Link ASPM Control [Disabled] 本項目用來設置 D M I L i n k 上北橋與南橋的 A S P M(A c t i v e S t a t e P o w e r Management)功能。設置值有:[Disabled] [Enabled]。 ASPM Support [Disabled] 本項目用來選擇 A S P M s t a t e 的節能狀態。設置值有:[D i s a b l e d] [L0s] [L1] [L0sL1] [Auto]。 SA - PCI Express 選項 DMI Link ASPM Control [Disabled] 本項目用來設置 DMI Link 上 CPU 與 PCH 的 ASPM(Active State Power Management)功能。在 CPU 與 PCH 中的 ASPM Control 都要設置為啟動才能使 ASPM 功能生效。設置值有:[Disabled] [L0s] [L1] [L0sL1]。 PEG ASPM Support [Disabled] 本項目
3.6.7 內置設備設置(OnBoard Devices Configuration) 將滾動條往下滾動來顯示以下項目。 [Enabled] 啟動高保真音頻控制器。 [Disabled] 關閉這個控制器。 以下選項只有在 HD Audio Controller 設置為 [Enabled] 時才會出現。 Front Panel Type [HD] 本項目可以讓您依照前面板音頻模塊支持的音頻標準,將前面板音頻連接端口 (AAFP)模式設置為 legacy AC’97 或是高保真音頻。 [HD] 將前面板音頻連接端口(AAFP)模式設置為高保真音頻。 [AC97] 將前面板音頻連接端口(AAFP)模式設置為 legacy AC’97。 SPDIF Out Type [SPDIF] [SPDIF] 設置為 SPDIF 輸出。 [HDMI] 設置為 HDMI 輸出。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
ASMedia USB 3.1 Controller [Enabled] 本項目用來啟動系統的 A S M e d i a ® U S B 3.1 控制器。設置值有:[D i s a b l e d] [Enabled]。 以下項目只有在 ASMedia USB 3.1 Controller 設置為 [Enabled] 時才會 出現。 ASMedia USB 3.1 Battery Charging Support [Disabled] 本項目用來啟動系統支持 A S M e d i a ® U S B 3.
以下項目只有在 Realtek LAN Controller 設置為 [Enabled] 時才會出現。 Realtek PXE Option ROM [Disabled] 本項目可讓您開啟或關閉 Realtek 網絡控制器的 PXE OptionRom。設置值有: [Enabled] [Disabled]。 Intel LAN Controller [Enabled] [Enabled] 啟動 Intel LAN 網絡控制器。 [Disabled] 關閉此控制器。 以下選項只有在 Intel LAN Controller 設置為 [Enabled] 時才會出現。 Intel PXE OPROM (LAN1-LAN2) [Disabled] 本項目可讓您開啟或關閉 Intel 網絡控制器的 PXE OptionRom。設置值有: [Enabled] [Disabled]。 ErP Ready [Disabled] 在 S4+S5 或 S5 休眠模式下關閉某些電源,減少待機模式下電力的流失,以符 合歐盟能源使用產品(Energy Related Product)的規範。網絡喚醒功能(WOL)、
Power On By RTC [Disabled] [Disabled] 關閉實時時鐘(RTC)喚醒功能。 [Enabled] 當您設為 [Enabled] 時,將出現 RTC Alarm Date (Days) 與 Hour/ Minute/Second 子項目,您可自行設置時間讓系統自動啟動。 3.6.
3.6.
3.
CPU Q-Fan Control [Auto] 本項目用來設置 CPU Q-Fan 運行模式。 [Auto] 檢測安裝的處理器風扇類型並自動切換控制模式。 [PWM Mode] 在 PWM 模式啟動 CPU Q-Fan 控制來使用 4-pin 處理器風扇。 [DC Mode] 當安裝 3-pin 的處理器風扇時,請選擇本項目來使用 Q-Fan 控 制的 DC 模式。 [Disabled] 關閉 CPU Q-Fan 控制功能。 以下的項目只有在 CPU Q-Fan Control 設為 [Auto]、[PWM Mode] 與 [DC Mode] 時才會出現。 CPU Fan Speed Low Limit [300 RPM] 本項目可以讓您設置 CPU Q-Fan Control 的功能及處理器風扇速度。設置值 有:[Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]。 CPU Fan Profile [Standard] 本項目用來設置處理器風扇適當的性能。 [Standard] 設置為 [Standard]
Chassis Fan 1/4 Q-Fan Control 1/4 [Enabled] 這些項目用來設置主板機箱風扇的 Q-Fan control 為 DC 模式、PWM 模式或關閉 Q-Fan controls 功能。設置值有:[Disabled] [DC Mode] [PWM Mode]。 以下項目只有在 Chassis Fan 1/4 Q-Fan Control 1/4 設置為 [PWM Mode] 或 [DC Mode] 時才會出現。 Chassis Fan 1/4 Q-Fan Source [DC Mode] 本項目用來根據選擇的溫度來源控制指派的風扇。設置值有:[C P U] [M B] [VRM] [PCH Core] [T_SENSOR1]。 若選擇 T_SENSOR1,請將熱敏電阻排線插在 T_SENSOR1 接口,並將 熱敏電阻排線接口貼在溫度來源的元件上。 Chassis Fan 1/4 Speed Low Limit 1/4 [300 RPM] 本項目用來關閉或設置機箱風扇警告轉度。設置值有:[I g n o r e] [200 R P M] [300 RPM] [400 RPM]
Allow Fan Stop 1/3 [Disabled] 本項目用來讓您的風扇在來源溫度掉到最低溫以下時可以 0% 工作週期運行。 設置值有:[Disabled] [Enabled]。 ASST Fan 1/3 Q-Fan Control 1/4 [Enabled] 這些項目用來設置輔助風扇的 Q-Fan control 為 DC 模式、PWM 模式或關閉 Q-Fan controls 功能。設置值有:[Disabled] [DC Mode] [PWM Mode]。 以下項目只有在 ASST Fan 1/3 Q-Fan Control 1/4 設置為 [PWM Mode] 或 [DC Mode] 時才會出現。 ASST Fan 1/3 Q-Fan Source [DC Mode] 本項目用來根據選擇的溫度來源控制指派的風扇。設置值有:[C P U] [M B] [VCORE (BACK)] [DRAM] [PCH Core] [USB 3.
ASST Fan 1/3 Lower Temperature [40] 使用 <+> 與 <-> 鍵調整輔助風扇溫度的最小值。數值可能會隨著 Qfan 調 整而異。 ASST Fan 1/3 Min.
3.
Network Stack Driver Support [Disabled] [Disabled] 在 POST 時略過載入網絡協定堆棧驅動器。 [Enabled] 在 POST 時載入網絡協定堆棧驅動器。 Next Boot after AC Power Loss [Normal Boot] [Normal Boot] 電源中斷後,在下一次啟動時恢復至正常啟動速度。 [Fast Boot] 電源中斷後,在下一次啟動時加快啟動速度。 DirectKey (DRCT) [Enabled] [Disabled] 關閉 DirectKey 按鈕功能,當按下 DirectKey 按鈕時系統僅會啟動或 關機。 [Enabled] 當按下 DirectKey 按鈕時系統會啟動並直接進入 BIOS。 Boot Logo Display [Auto] [Auto] 設置在開機自檢(POST)過程中的啟動畫面。 [Full Screen] 設置在開機自檢(POST)過程中的啟動畫面為全屏。 [Disabled] 關閉全屏個人化啟動畫面功能。 以下項目只有在 Boot Logo
Option ROM Messages [Enabled] [Enabled] 選購設備固件信息會在開機自檢時顯示。 [Disabled] 在開機自檢時關閉選購設備固件信息並只顯示華碩啟動圖標。 Interrupt 19 Capture [Disabled] 本項目用來使用隨選內存(R O M)限制中斷 19。設置值有:[D i s a b l e d] [Enabled]。 Above 4G Decoding [Disabled] 本項目用來讓您在 4G 地址空間上解碼 64 位設備。設置值有:[D i s a b l e d] [Enabled]。 Setup Mode [EZ Mode] [Advanced Mode] 將 Advanced Mode 設置為 BIOS 設置程序的默認值。 [EZ Mode] 將 EZ Mode 設置為 BIOS 設置程序的默認值。 CSM(兼容性支持模塊) 本項目用來設置 CSM(兼容性支持模塊)項目來完全支持各種 VGA、啟動設備和 附加設備,藉以獲得更佳的兼容性。 Launch CSM [Auto] [Auto] 系統將自動檢測啟動設
Boot from Storage Devices [Legacy OpROM first] 本項目用來選擇想要運行的存儲設備類型。設置值有:[B o t h, L e g a c y OpROM first] [Both, UEFI first] [Legacy OpROM first] [UEFI driver first] [Ignore]。 Boot from PCIe/PCI Expansion Devices [Legacy OpROM first] 本項目用來選擇想要運行的 PCIe/PCI 擴展設備類型。設置值有:[Legacy OpROM first] [UEFI driver first]。 Secure Boot 本項目用來設置 Windows® 安全啟動的相關參數以及管理系統金鑰,以提升系統在 開機自檢(POST)時的安全性,避免受到未授權的用戶與惡意軟件的危害。 OS Type [Windows UEFI mode] [Windows UEFI Mode] 本 項 目 用 來 選 擇 安 裝 的 操 作 系 統 。 運 行 Microsoft ® 安全啟動檢查。只有在 Wind
Load PK from File 本項目用來由 USB 存儲設備載入已下載的平台金鑰(PK)。 PK 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 KEK Management KEK(金鑰交換金鑰 [Key-exchange Key] 或金鑰註冊金鑰 [Key-Enrollment Key])用來管理簽名數據庫(db)與撤銷簽名數據庫(dbx)。 Key-exchange Key(KEK)指的是 Microsoft ® Secure Boot KeyEnrollment Key(KEK)。 Delete the KEK 本項目用來刪除系統中的 KEK。設置值有:[Yes] [No]。 Load KEK from File 本項目用來由 USB 存儲設備載入已下載 KEK。 Append Var to KEK 本項目用來由存儲設備載入附加的 KEK,以管理附加的簽名數據庫(db) 與撤銷簽名數據庫(dbx)。 KEK 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 DB Management Delete the db 本項目用來刪除系統中的 db 文件。設置值有:[Ye
DBX Management dbx(撤銷簽名數據庫)列出 db 項目中不再被信任且無法被載入之被禁止的 圖片圖像。 Delete the dbx 本項目用來刪除系統中的 dbx 文件。 Load dbx from File 本項目用來由 USB 存儲設備載入已下載的撤銷簽名數據庫(dbx)。設置 值有:[Yes] [No]。 Append dbx from File 本項目用來由存儲設備載入附加的撤銷簽名數據庫(d b x),以使更多的 db 圖片圖像無法被載入。 dbx 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 Boot Option Priorities 本項目讓您自行選擇啟動磁盤並排列啟動設備順序。依照 1st、2nd、3rd 順序分 別代表其啟動設備順序,而設備的名稱將因使用的硬件設備不同而有所差異。 • 欲進入 Windows 安全模式時,請在開機自檢(POST)時按下 (Windows 8 不支持這項功能)。 • 啟動時您可以在 ASUS Logo 出現時按下 選擇啟動設備。 Boot Override 本項目將顯示可使用的設備,設備的名稱將因使用
3.9 工具菜單(Tools menu) 本工具菜單可以讓您針對特別功能進行設置。請選擇菜單中的選項並按下 鍵來顯示子菜單。 Setup Animator 本項目用來啟動或關閉設置動畫。設置值有:[Disabled] [Enabled]。 本項目可以讓您啟動華碩 EZ Flash 2 程序,按下 會出現再次確認的窗 口,請使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 3.11.2 華碩 EZ Flash 2 的說明。 華碩 SABERTOOTH Z97 MARK 1/USB 3.1 主板用戶手冊 3-57 第三章 3.9.
3.9.2 ASUS O.C.
3.9.3 ASUS SPD Information 第三章 本菜單顯存插槽的相關信息。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
3.
3.11 更新 BIOS 程序 華碩網站上提供有最新的 B I O S 程序,可以強化系統的穩定度、兼容性或運行性 能,但是運行 BIOS 程序更新是具有潛在性風險的,若是使用現有版本的 BIOS 程序 都沒有發生問題時,請勿手動運行更新 BIOS 程序。不適當的 BIOS 程序更新可能會 導致系統啟動失敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程序。 請訪問華碩網站(http://www.asus.com.cn)來下載本主板最新的 BIOS 程序。 1. EZ Update:在 Windows 操作系統中更新 BIOS 程序。 2. ASUS EZ Flash 2:使用 U 盤來更新 BIOS。 3. ASUS CrashFree BIOS 3:當 BIOS 文件遺失或損毀時,可以使用 U 盤或主板的 驅動程序與應用程序光盤來更新 BIOS。 4. ASUS BIOS Updater:在 DOS 環境下,使用主板驅動程序與應用程序光盤與 U 盤來更新並備份 BIOS。 上述軟件請參考相關章節的詳細使用說明。 3.11.
3.11.2 華碩 EZ Flash 2 華碩 EZ Flash 2 程序讓您能輕鬆的更新 BIOS 程序,可以不必再通過啟動盤的冗 長程序或是到 DOS 模式下運行。 請至華碩網站 http://www.asus.com.cn 下載最新的 BIOS 程序文件。 請依照以下步驟通過 EZ Flash 2 更新 BIOS 程序: 1. 將保存有最新的 BIOS 文件的 U 盤插入 USB 連接端口。 2. 進入 BIOS 設置程序的 Advanced Mode,選擇 Tool > ASUS EZ Flash Utility, 接著請按下 鍵。 第三章 3. 請使用 鍵操控 Drive 區域。 4. 請利用上/下方向鍵找到存放有最新 B I O S 文件的 U 盤,接著請按下 鍵。 5. 請使用 鍵操控 Folder Info 區域。 6.
• 本功能僅支持採用 FAT 32/16 格式的單一磁區 U 盤。 • 當更新 BIOS 時,請勿關閉或重置系統以避免系統啟動失敗。 請讀取出廠默認值來保持系統的穩定。請參閱 3.10 退出 BIOS 程序 一節 中 Load Optimized Defaults 項目的詳細說明。 3.11.3 華碩 CrashFree BIOS 3 華碩最新自行研發的 CrashFree BIOS 3 工具程序,讓您在當 BIOS 程序和數據被 病毒入侵或丟失時,可以輕鬆的從驅動程序及應用程序光盤,或是從含有最新或原始 的 BIOS 文件的 U 盤中恢復 BIOS 程序的數據。 在驅動程序及應用程序光盤中的 B I O S 程序版本可能會比官方網站上 的 BIOS 程序版本舊,若是想要使用更新的 BIOS 程序,請至 http:// support.asus.com 網站下載,並保存在便攜存儲設備中。 恢復 BIOS 程序 請依照下列步驟使用應用程序光盤恢復 BIOS 程序: 1. 啟動系統。 2.
3.11.4 華碩 BIOS Updater 華碩 BIOS Updater 讓您可以在 DOS 環境下更新 BIOS 程序,還可以用來複製現 有的 BIOS 文件,當您的 BIOS 程序在更新過程中失敗或中斷時,可以作為備份使 用。 以下的程序畫面僅供參考,您實際操作的畫面可能會與手冊所示的畫面 不盡相同。 更新 BIOS 之前 1. 準備本主板的驅動程序與應用程序光盤,以及 USB 存儲設備。 2. 訪問華碩網站 http://support.asus.com 下載最新的 BIOS 程序與 BIOS Updater, 然後保存在 USB 存儲設備。 DOS 環境下不支持 NTFS 格式,請確認 USB 存儲設備為 FAT32/16 格 式且單一磁區的格式。 3. 將電腦關機。 4. 請確認電腦配備有光驅。 DOS 環境下啟動系統 1. 將存有最新 BIOS 文件與 BIOS Updater 的 USB 存儲設備插入 USB 連接端口。 2. 啟動電腦,按下 來顯示 BIOS 啟動設備選擇菜單。 3.
4. 當啟動信息出現時,在五秒鐘內按下 鍵來進入 FreeDOS 彈出窗口。 ISOLINUX 3.20 2006-08-26 Copyright (C) 1994-2005 H. Peter Anvin A Bootable DVD/CD is detected. Press ENTER to boot from the DVD/CD. If no key is pressed within 5 seconds, the system will boot next priority device automatically. boot: 5. 當 FreeDOS 出現時,輸入命令 d:,然後按下 ,將磁盤 C(光驅)改為磁 盤 D(USB 存儲設備)。 Welcome to FreeDOS (http://www.freedos.org)! C:/> d: D:/> 更新 BIOS 文件 請依照以下步驟更新 BIOS 文件: 1.
4. BIOS Updater 檢查所選的 BIOS 文件後,選擇 Yes 來確認 BIOS 更新。 Are you sure you want to update the BIOS? Yes No 由於安全規則,不支持 BIOS 備份功能。 5. 選擇 Yes 然後按下 ,當 BIOS 更新完成時,按下 退出 BIOS Updater。 6. 重新啟動電腦。 請勿在 BIOS 進行更新時,運行關機或重新啟動電腦,以防止 BIOS 更新 失敗。 請載入 BIOS 程序的默認值以確保系統的兼容性與穩定度。在 3.
第四章 4.1 安裝操作系統 • 本主板支持 Microsoft ® 32-bit/64-bit Windows ® 7、32-bit/64bit Windows ® 8、32-bit/64-bit Windows ® 8.1 操作系統(OS, Operating System)。 • 由於主板和周邊硬件設備的選項設置繁多,本章僅就軟件的安裝程序 供您參考。您也可以參閱您使用的操作系統說明文件以取得更詳盡的 信息。 4.2 驅動程序及應用程序 DVD 光盤信息 隨貨附贈的驅動程序及應用程序 DVD 光盤包括了數個有用的軟件和應用程序,將 它們安裝到系統中可以強化主板的性能。 華碩驅動程序及應用程序 D V D 光盤的內容會不定時地更新,但不另行 通知。如欲得知最新的信息,請訪問華碩的網站 http://www.asus.com. cn。 4.2.1 運行驅動程序及應用程序 DVD 光盤 當您在 Windows 7、Windows 8 或 Windows 8.1 操作系統中運行驅動 程序及應用程序 DVD 光盤之前,請先確認您擁有管理員帳號。 請依照以下步驟運行驅動程序及應用程序 DVD 光盤: 1.
驅動程序及應用程序 DVD 光盤 驅動程序菜單顯示系統檢 測到連接設備可使用的驅 動程序,請安裝適當的驅 動程序來使用該設備 軟件菜單顯示 本主板支持的 應用程序與其 他軟件 取得 RAID/AHCI 驅動程序 手冊菜單顯示本光盤 所附的用戶手冊,點 擊想要的項目來開啟 用戶手冊的文件夾 點擊聯絡信 息標籤頁顯 示與華碩聯 絡的信息 點擊圖標顯 示 DVD/主 板信息 點擊安裝各 項驅動程序 第四章 4-2 第四章:軟件支持
4.2.2 取得軟件用戶手冊 您可在驅動程序 DVD 光盤中找到軟件用戶手冊,請依照以下步驟來取得您需要的 軟件用戶手冊。 軟件用戶手冊文件為 P D F 格式,在您開啟用戶手冊文件前,請先安裝 Adobe® Acrobat® Reader 瀏覽軟件。 1. 點擊 M a n u a l(用戶手冊) 標 籤頁,由列表中選擇 A S U S Motherboard Utility Guide。 2. 進入 Manual(用戶手冊) 文件 夾後,在您需要的用戶手冊文件 夾用鼠標左鍵點二下。 第四章 3. 請由數個語言的用戶手冊中選擇 您需要的用戶手冊。 本章節的圖標僅供參考,在驅動程序 D V D 光盤中所包含的軟件用戶手 冊,會依照您所購買的型號而有不同。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.3 軟件信息 驅動程序及應用程序光盤中大部分的應用程序都會有安裝指導向導來協助您一步一 步輕鬆地安裝軟件。您也可以由個別軟件所提供的在線說明文件或讀我文件取得安裝 方式及其他信息的說明。 4.4 華碩 AI Suite 3 程序 通過友善的用戶界面,華碩 AI Suite 3 程序將所有的華碩獨家功能集成在一個軟件 套件中,可以同時操控並運行各項功能及應用程序。 安裝華碩 AI Suite 3 程序 在您將 AI Suite 3 程序安裝至 Windows 7、Windows 8 或 Windows 8.1 操作系統之前,請先確認您擁有管理員帳號。 請依照下列步驟將華碩 AI Suite 3 程序安裝到您的電腦: Windows 7 操作系統 1. 將驅動程序及應用程序 DVD 光盤放入光驅。 2. 在自動播放(AutoPlay)對話框中點擊運行 ASSETUP.exe。 3.
Windows 8 與 Windows 8.1 操作系統 1. 將驅動程序及應用程序 DVD 光盤放入光驅,然後依照屏幕的指示來完成安裝步 驟。 2. 從驅動程序及應用程序 DVD 光盤主菜單中選擇應用程序(Utilites)標籤頁,然 後點擊 AI Suite 3。 3. 請依照屏幕的指示運行。 若是驅動程序及應用程序 DVD 光盤主菜單沒有出現,請參考以下步驟: a. 到 開始 畫面,然後點擊或輕觸桌面的應用程序。 b. 在桌面的左下角點擊或輕觸 File Explorer 觸或雙擊 設置。 ,然後選擇 DVD 磁盤並輕 運行華碩 AI Suite 3 程序 Windows 7 操作系統 從桌面點擊 開始 > 所有應用程序 > ASUS > AI Suite 3> AI Suite 3。 您也可以在 Windows 7 的通知任務欄中點擊 。 Windows 8 與 Windows 8.
AI Suite 3 主畫面 AI Suite 3 主畫面提供您輕鬆進入控制和了解電腦發生了什麼狀況 - 能提供您將性 能做最佳化設置,並同時確保系統的穩定性。 AI Suite 主畫面包含一個快速進入的主菜單工具列,可以讓您快速開啟任何集中在 這裡的華碩應用程序。點擊主畫面右上方 圖標便可以開啟此主菜單工具列。 點擊以啟動 AI Suite 3 菜單工具列 AI Suite 3 主畫面僅供參考,請以您實際看到的畫面為準。 AI Suite 3 主菜單工具列 Thermal Radar 2 Ai Charger+ 第四章 USB 3.1 Boost EZ Update USB BIOS Flashback 推播信息 系統信息 USB Charger+ 版本 • 本章節的畫面僅供參考,請以您實際看到的畫面為準。 • 請參考驅動程序 D V D 光盤中軟件手冊的說明,或訪問華碩網站 http://www.asus.com.
Thermal Radar 2(熱敏雷達 2)程序 Thermal Radar 2(熱敏雷達 2)讓您可以實時控制風扇、監控顯卡與其他元件的 溫度,或自動調整溫度設置。 Fan Control(風扇控制) 本項目用設置安裝在系統中的風扇,您也可以載入或保存風扇設置文件來調整系統 的溫度狀況。 點擊以載入已保存的設置文件 點擊以在項 目間切換 點擊以保存為 新的設置文件 風扇超時設置 Dust de-Fan 設置 VGA 本項目用來設置已安裝的華碩顯卡的散熱設置。 • Thermal Radar 2 的 VGA 標籤頁只有在安裝有選用的華碩顯卡時才 會出現。 • Thermal Radar 2 的 VGA 功能僅支持華碩 NVidia 700 系列顯卡。 VGA - Auto Mode 第四章 系統將載入顯卡散熱設置的最佳化數值。 點擊以動態調整已安裝之 顯卡的電力與風扇速度 點擊以儲存新的設置文件 點擊以載入已保存的設置文件 華碩 SABERTOOTH Z97 MARK 1/USB 3.
VGA - Smart Mode 本項目用來手動調整顯卡風扇的加速與加速時間。 點擊以應用設置 顯示散熱設置之圖形 點擊滑桿以 調整設置 點擊以還原更改 點擊以儲存新的設置文件 點擊以載入已保存的設置文件 VGA - RPM Mode 本項目用來手動調整風扇的轉速(rpm)。 當本項目為關閉會以灰色顯示,請按下風扇調整(Fan Tuning)按鈕。 第四章 上下移動滑桿來調整設置 4-8 第四章:軟件支持 點擊以儲存新的設置文件 點擊以載入已保存的設置文件
Thermal Tuning(熱敏調校) 這個功能會依照系統現在的溫度設置,自動為系統提供最佳化冷卻解決方案。可以 讓您設置處理器、機箱與獨家 TUF 渦輪風扇來獲得冷卻性能與低噪音之間的平衡。 點擊以自動開始進 行熱敏調校操作 Thermal Status(熱敏狀態) 顯示系統現在的溫度狀況。 點擊以評估現 在的溫度設置 Recorder(記錄) 顯示與監控溫度設置的狀況與系統狀態。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
DIGI+ Power Control 程序 華碩 DIGI+ Power Control 電源控制擁有革命性與創新的數字 VRM 與 DRAM 內 存電壓控制器。這些控制器提供極度精確的內存與電壓調整,帶給您最佳的效率、穩 定性與系統性能。 點擊以進入處 理器設置畫面 點擊以進入內 存設置畫面 DIGI+ Power Control - CPU 點擊回到上 一個畫面 點擊以在項 目間切換 點擊以取消更改 點擊以應 用更改 DIGI+ Power Control - DRAM 第四章 點擊回到上 一個畫面 4-10 第四章:軟件支持 點擊以取消更改 點擊以應 用更改
4.4.1 Ai Charger+ 這個程序可以對連接在 USB 連接端口上的便攜 BC 1.1* 行動設備進行快速充電, 並且充電速度較標準 USB 設備快三倍**。 運行 Ai Charger+ 若要運行 Ai Charger+,請點擊屏幕右上方 單工具列上的 Ai Charger+。 圖標,然後點擊 AI Suite 3 主菜 只有某些型號的主板有 Ai Charger+ 功能。 Ai Charger+ 主畫面 勾選以啟動或關閉 Ai Charger+ 點擊以應用 • *請確認您的 USB 設備製造商是否完整支持或兼容 BC 1.1 功能。 • **實際的充電速度會隨著您的 USB 設備狀況而有不同。 • 在啟動或關閉 Ai Charger+ 程序之後,請卸除並重新連接您的 USB 設備,以確保能正常使用充電功能。 第四章 • Ai Charger+ 不支持 USB 集線器、USB 延長線以及一般的 USB 排 線。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.4.
手動更新 BIOS 與選擇啟動圖標 點擊以搜索您想使用的啟動圖標文件 點擊以回到 EZ Update 主畫面 點擊以運行更新 BIOS 與啟動圖標 第四章 在您點擊 BIOS Update 按鈕後,點擊 Flash 開始更新 BIOS 與上傳啟動圖標文 件至您的系統。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.4.3 USB BIOS Flashback 向導 USB BIOS Flashback 向導可以查看並將最新版 BIOS 程序保存至 USB 存儲設備, 配合 ASUS USB BIOS Flashback 的硬件特色,讓您不需重新啟動即可更新 BIOS 程 序。 運行華碩 USB BIOS Flashback 程序 若要運行 USB BIOS Flashback,請點擊 AI Sutie 3 主菜單右上方的 然後選擇 USB BIOS Flashback。 圖標, USB BIOS Flashback 只適用於特定的主板型號。 使用 USB BIOS Flashback 程序 設置下載 BIOS 更新的排程 點擊以取消下 載的排程設置 點擊以確認是否有 BIOS 固件更新可下載 點擊以應用下 載的排程設置 設置下載 BIOS 更新的排程 1. 請於 Download Setting(下載設置) 中勾選 Schedule (days)(排程),並選擇 下次進行下載更新的天數。 2.
下載最新版 BIOS 下載前請先確認已經將支持 USB BIOS Flashback 的 USB 存儲設備連接 至電腦的 USB 連接端口。請參考 2.3.1 後側面板連接端口 一節的詳細說 明。 請依照以下步驟下載最新版 BIOS: 1. 在 USB BIOS Flashback 主畫面中點 擊 Check for New BIOS Update 查 看是否有 BIOS 固件更新可下載。 請等待系統確認最新版的 BIOS 固件 版本。 2. 當檢測到新版 B I O S 固件時,請由 Save to 點擊 ,選擇 USB 存儲設 備後請點擊 Download。 SABERTOOTH Z97 MARK 1/USB 3.1 第四章 3 下載完後請點擊 OK。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.4.4 推播信息(Push Notice) 這個應用程序讓您可以將系統狀態的詳細信息傳送至智能型設備,您也可以使用這 個程序傳送信息至智能型設備。 使用這個應用程序之前,請先確認您的電腦與智能型設備已經完成配 對。請參考 配對電腦與智能型設備 一節的詳細信息。 啟動電腦的推播信息(Push Notice) 若要啟動推播信息,請點擊 AI Sutie 3 主菜單右上方的 Push Notice。 圖標,然後選擇 推播信息(Push Notice)主畫面 點擊以啟動或關閉推播信息(Push Notice) 勾選智能 型設備 點擊以放棄設置 點擊以應用設置 您也可以通過屏幕右上角的 P u s h N o t i c e 快捷方式來啟動推播信息功 能,請點擊 << 然後點擊 ,再選擇 。 配對電腦與智能型設備 請依照以下步驟配對電腦與智能型設備: 1. 在智能型設備點擊 來啟動推播信息(Push Notice)。 2.
設置要發出警告的模式 本功能用來設置當電腦重新啟動、關機或進入睡眠模式時,傳送警示信息至智能型 設備。 勾選這些項目來選擇 欲啟動警示的模式 勾選智能 型設備 設置日期與時 間來啟動模式 設置在模式啟動前 幾分鐘要傳送警示 輸入要傳送的信息 設置電腦狀態警示 本功能用來將電腦上不正常的狀態,如:電壓、溫度和風扇設置等信息傳送警示至 智能型設備。 勾選智能 型設備 勾選欲傳送至智 能型設備的項目 第四章 勾選本項目當元件恢復正常狀 態時傳送警示至智能型設備 華碩 SABERTOOTH Z97 MARK 1/USB 3.
傳送信息至智能型設備 本功能用來傳送信息至智能型設備。 您也可以通過屏幕右上角的推播信息(Push Notice)信息快捷方式來傳 送信息,請點擊 << 然後點擊 ,再選擇 。 勾選智能 型設備 點擊來傳 送信息 點擊來輸入信息 點擊來清除信息 欄中的所有文字 點擊來保存信息 在智能型設備查看電腦狀態 在智能型設備點擊 來啟動推播信息(Push Notice)。 Push Notice 點擊以查看 警示模式 點擊以查看 警示狀態 點擊以查看傳 送過的信息 點擊以掃描 更多主機 第四章 4-18 第四章:軟件支持 點擊以刪 除警示
4.4.5 華碩 USB 3.1 Boost 程序 華碩 USB 3.1 Boost 程序支持 USB 連接 SCSI 協議(UASP,USB Attached SCSI Protocol)。通過華碩 USB 3.1 Boost 程序,可輕鬆提升您的 USB 設備之傳輸速 度。 運行華碩 USB 3.1 Boost 程序 若要運行 USB 3.1 Boost,請點擊 AI Sutie 3 主菜單右上方的 選擇 USB 3.1 Boost。 圖標,然後 使用華碩 USB 3.1 Boost 程序 點擊以啟動 USB 設備 的正常數據傳輸率 點擊以選擇 USB 設備 點擊以啟動 UASP 或 Turbo 模式來獲得更快 的數據傳輸率 請將您的 USB 3.1/3.0 設備連接到支持 USB 3.1 Boost 的 USB 3.1/3.0 連接端口,請參考 2.3.1 後側面板連接端口 以了解更多說明。 • USB 3.1 Boost 程序會自動檢測支持 UASP 功能的 USB 3.1/3.0 設 備。 第四章 • 使用 USB 3.1/3.
4.4.
查看 SPD 信息 第四章 從系統信息主畫面,點擊 SPD 標籤頁來查看內存的相關信息。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.4.7 USB Charger+ USB Charger+ 用來快速充電您的便攜 USB 設備,即使在電腦關機、睡眠狀態或 休眠狀態仍可進行充電。 在使用 USB Charger+ 之前,請先確認關閉在 BIOS 設置中 Advanced 模式的 Advanced > APM > ErP Ready 的 Erp Ready 選項。 運行 USB Charger+ 若要運行 USB Charger+,請點擊 AI Sutie 3 主菜單右上方的 擇 USB Charger+。 圖標,然後選 USB Charger+ 主畫面 點擊來檢測 已連接的 USB 設備 點擊以快速 充電您的 USB 設備 顯示連接的 USB 設備正處 於充電中模式 點擊以停止 充電您的 USB 設備 點擊以應 用設置 點擊您想要在系統關機時進 行充電的 USB 設備類型 點擊以取消 應用設置 請確認將您的 U S B 設備連接至支持本程序之 U S B 連接端口。請參考 2.3.
4.4.8 版本 第四章 顯示已經安裝的軟件或應用程序現在的版本。 華碩 SABERTOOTH Z97 MARK 1/USB 3.
4.
4.
選擇音頻輸出 Realtek HD Audio Manager 讓您依照使用的輸出設備來選擇音頻輸出類型。 請依照以下步驟選擇輸出音頻: 1. 將設備接口插入聲音輸出(草綠色)連接端口,若是設備接口已經插入至相對應 的連接端口,點擊 Realtek HD Audio Manager 中的 圖標。 2. 在彈出窗口中勾選插入至聲音輸 出端的設備,然後點擊 下一步 (Next)。 a. 若 選 擇 耳 機 (Headphone),請點擊 安裝的耳機類型然後再點 擊 OK。 b.
第五章 5.1 RAID 功能設置 本主板支持以下 SATA RAID 解決方案。 • Intel® Rapid Storage Technology:支持 RAID 0、RAID 1、RAID 10 和 RAID 5。 5.1.
5.1.2 安裝 Serial ATA(SATA)硬盤 本主板支持 Serial ATA 硬盤。為了最佳的性能表現,當您要創建陣列模式設置 時,請盡可能採用具備相同型號與容量的硬盤。 請依照以下安裝方式來建構 SATA RAID 磁盤陣列: 第五章 1. 將硬盤安裝至硬盤槽中。 2. 安裝硬盤連接排線,將欲建構磁盤陣列的硬盤連接至主板。 3. 將 SATA 電源線連接到每一部硬盤。 5.1.3 在 BIOS 程序中設置 RAID 在您開始創建陣列之前,您必須先在 BIOS 程序設置中設置對應的 RAID 選項。請 依照下列步驟進行操作︰ 1. 在啟動之後系統仍在內存的啟動自我測試(Power-On Self Test,POST)時,按 下 按鍵進入 BIOS 設置程序。 2. 進入主菜單(Main)後,選擇 Advanced > SATA Configuration 選項,然後按 。 3. 將 SATA Mode 選項設置為 [RAID Mode]。 4.
5.1.4 進入 Intel® Rapid Storage Technology Option ROM 應用程序 請依照下列步驟來進入 Intel® Rapid Storage Technology Option ROM 應用程序: 1. 啟動您的電腦。 Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID RAID Volumes: None defined. Physical Devices: Port Device Model 0 ST3160812AS 1 ST3160812AS 2 ST3160812AS 3 ST3160812AS [↑↓]-Select MENU ] 4.
創建 RAID 設置 請依照下列步驟創建 RAID 設置: 1. 選擇 1. Create RAID Volume 然後按下 按鍵,會出現如下圖所示的窗口 畫面。 第五章 Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: Disks: Strip Size: Capacity: Sync: Create volume [ HELP ] Enter a unique volume name that has no special characters and is 16 characters or less. [↑↓]-Select [ESC]-Exit [ENTER]-Select Menu 2. 為您的 RAID 磁區鍵入一個名稱,然後按下 按鍵。 3.
6. 使用向上、向下方向鍵來選擇 RAID 磁盤陣列(RAID 0、RAID 10、RAID 5)要 分區的容量,然後按下 按鍵。分區的數值可由 4KB 遞增至 128KB,數 據分區的數值應該以硬盤使用的目的來決定。下列為推荐: RAID 0: 128KB RAID 10: 64KB RAID 5: 64KB 若此系統欲作為服務器使用,建議您選擇較低的磁區大小;若此系統欲 作為多媒體電腦用來運行影音的編輯製作,建議您選擇較高的磁區大小 來獲得最佳的性能。 7. 輸入您所要的陣列容量,接著按下 按鍵。本項目默認值是採用最高可容 許的磁盤容量。 8. 在 Create Volume 的提示對話框中再按下 按鍵來創建磁盤陣列,接著便 會出現如下圖的窗口畫面。 WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 9.
刪除 RAID 陣列 當您要刪除 RAID 設置時請小心,保存在硬盤中的數據會被全部刪除。 第五章 請依照以下步驟刪除 RAID 陣列: 1. 選擇 2. Delete RAID Volume 然後按下 按鍵,會出現如下圖所示的窗口 畫面。 Name Volume0 [ DELETE VOLUME MENU ] Level Drives RAID0(Stripe) 2 Capacity 298.0GB Status Normal Bootable Yes [ HELP ] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED. (This does not apply to Recovery volumes) [↑↓]-Select [ESC]-Previous Menu [DEL]-Delete Volume 2.
5.2 在安裝 Windows® 操作系統時安裝 RAID 驅動程序 請依照下列步驟在 Windows® 操作系統中安裝 RAID 驅動程序: 2. 將搭載有 RAID 驅動程序的光盤/ U 盤安裝光驅/ USB 連接端口,並點擊 Browse (瀏覽)。 3. 請選擇您的設備後,選擇 Drivers > RAID,然後選擇 RAID 驅動程序文件,再按 下 OK。 4. 請依照屏幕指示來完成驅動程序的安裝。 在從 U 盤載入 RAID 驅動程序之前,您必須使用另一台電腦來將應用程 序光盤中的 RAID 驅動程序複製到 U 盤。 要在 RAID 模式下設置 Windows ® UEFI 操作系統,請先為光驅載入 UEFI 驅動程序。 華碩 SABERTOOTH Z97 MARK 1/USB 3.1 主板用戶手冊 5-7 第五章 1.
第五章 5-8 第五章:RAID 支持
附錄 華碩的聯絡信息 華碩電腦(上海)有限公司 ASUSTEK COMPUTER (SHANGHAI) CO., LTD 市場信息 技術支持 地址: 上海市閔行莘庄工業區春東路508號 電話:+86-21-54421616 傳真:+86-21-54420099 互聯網:http://www.asus.com.cn/ 電話: +86-20-28047506(400-6206655) 電子郵件: http://vip.asus.com.cn/VIP2/ Services/QuestionForm/ TechQuery 在線支持: http://www.asus.com/support 華碩電腦公司 ASUSTeK COMPUTER INC.(亞太地區) 市場信息 技術支持 地址: 台灣臺北市北投區立德路15號 電話:+886-2-2894-3447 傳真:+886-2-2890-7798 電子郵件:info@asus.com.tw 互聯網:http://www.asus.com.tw 電話:+86-21-38429911 傳真: +86-21-58668722, ext.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Original Declaration Date : Corrected Declaration Date : Signature : Representative Person’s Name : Sep. 29, 2014 Jan. 27, 2015 Steve Chang / President This device complies with part 15 of the FCC Rules.