Zhone 6218-i3 4-Port Wi-Fi Ethernet Router User Manual Version 1.
Table of Contents GENERAL INFORMATION .......................................................................... 3 Package Contents ........................................................................ 3 Important Safety Instructions.......................................................... 3 Front Panel View ......................................................................... 4 Back Panel View .......................................................................... 5 INSTALLING THE ROUTER .......
Tone Settings .....................................................................47 Port Mapping.............................................................................48 IPSec.......................................................................................49 Certificate ...............................................................................50 Local ...............................................................................50 Trusted CA ..............................................
General Information The 4-Port Wireless Ethernet Router features 4 LAN ports for added convenience and accessibility. Package Contents Included in the package is one of each of the following— x x x x x 4-Port Wireless Ethernet Router 12V 1.5A power adapter RJ-11 telephone cable RJ-45 Ethernet cable User Manual Important Safety Instructions x Place your router on a flat surface close to the cables in a location with sufficient ventilation.
Front Panel View LED Power Status Mode Indication Solid Router is powered on. Router is not powered. Check if the router is plugged in and if the power switch is turned on. Connection established. The router is able to communicate with your ISP via ADSL. The router is trying to connect to your ISP. ADSL is connected. ADSL is not connected. The ALARM led will be red. The router is connected to ADSL. Router is connected to the LAN. No connection to the LAN.
Back Panel View NOTE: The below port descriptions are listed as they appear on the back panel from left to right. Port Description Power Connects to a 15VAC 1A power adapter. Restart—press the button for less than 4 seconds. Default settings—press the button for 4 seconds or longer. RJ-45 connects the unit to an Ethernet device such as a PC or a switch. RJ-11 cable connects to telephone (no external splitter necessary; unit has internal splitter).
Installing the Router Connect the ADSL Line and Telephone x Connect one end of an RJ-11 cable from your ADSL connection and the other end to the LINE port of the router using a splitter if needed. NOTE: See connections on the installation diagram. Connect the PC to the Router x To use the Ethernet connection, connect the Ethernet cable from the computer directly to the router.
Installation Diagram Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Mounting the Router The router can be mounted on the wall with the screws provided. Mounting can be done on wall material including concrete, wood, or drywall. Select an appropriate location free from obstructions or any possible interference. Make sure the cables can be easily attached to the router without strain. The illustration below shows how to mount the router horizontally on a wall. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Configuring Your Computer Prior to accessing the router through the LAN or the USB port, note the following necessary configurations— x Your PC’s TCP/IP address: 192.168.1.__( the last number is any number between 2 and 254) x The router’s default IP address: 192.168.1.1 x Subnet mask: 255.255.255.0 Below are the procedures for configuring your computer. Follow the instructions for the operating system that you are using. Windows 2000 1.
Windows XP 1. In the Windows taskbar, click on the Start button and point to Settings and then click Network Connections. 2. In the Network Connections window, right click on the Local Area Connection icon and click on properties. 3. Listed in the Local Area Connection window are the installed network components. Make sure the box for Internet Protocol (TCP/IP) is checked and then click on Properties. 4.
Log in to the Router This section will explain how to log in to your router using the following steps— 1. Launch your web browser. 2. Enter the URL http://192.168.1.1 in the address bar and press Enter. A login screen like the one below will be displayed after you connect to the user interface. 3. Enter your user name and password, and then click on OK to display the user interface. NOTE: There are two default user name and password combinations.
Device Info This section describes the system information that can be accessed using the menu items under Device Info. Summary Access the general information of the router by clicking on “Summary” under “Device Info”. It shows details of the router such as the version of the software, bootloader, LAN IP address, etc. It also displays the current status of your DSL connection as shown below— Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
WAN Access the WAN status report from the router by clicking on “WAN” under “Device Info”. Below is how the screen will look once a WAN connection is set up. Statistics LAN Statistics Access the LAN statistics from the router by clicking on the “LAN” item under “Statistics” Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
WAN Statistics Access the WAN statistics from the router by clicking on the “WAN” item under “Statistics”. ATM Statistics Access ATM statistics from the router by clicking on the “ATM” item under “Statistics”. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
ADSL Statistics You can view ADSL statistics by clicking on the “ADSL” item under “Statistics”. Information contained in this screen is useful for troubleshooting and diagnostics of connection problems. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
ADSL BER Test A Bit Error Rate Test (BER Test) is a test that reflects the ratio of error bits to the total number transmitted. If you click on the ADSL BER Test button at the bottom of the ADSL Statistics page, the following pop-up screen will appear allowing you to set the tested time and to begin the test. Below is an ADSL BER Test result screen displaying information about the test and the error bits and ratio. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Route Access the routing status report from the router by clicking on the “Route” item under “Device Info”. ARP Access the ARP status report from the router by clicking on the “ARP” item under “Device Info”. ARP (Address Resolution Protocol) maps the IP address to the physical address, labeled HW Address (the MAC address) and helps to identify computers on the LAN. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
DHCP Access the DHCP Leases screen by clicking “DHCP” under “Statistics”. This shows the computers, identified by the hostname and MAC address that have acquired IP addresses by the DHCP server with the time that the lease for the IP address is up. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Quick Setup This section will explain how to quickly configure the router for the sole purpose of connecting to the Internet. ATM PVC Configuration To enable the auto-connect process, click on the box labeled DSL Auto-connect, a process that will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To continue, click on the Next button. If you uncheck the DSL Auto-connect box, the resulting screen is seen below.
Following is the Connection Type screen where you select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use. The following is a PPPoA example. Click on Next to continue. Enter the PPP username and password as given by your ISP. Then decide if you will be using any features such as dial on demand, PPP IP extension, keep alive and then click on Next. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
The next step is to configure the Network Address Translation (NAT) settings. For the example, NAT will be enabled. The remaining fields are left as default and then click on Next to continue. You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond to your LAN’s IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers.
The next screen allows you to enable or disable the router’s wireless option. Also be sure to enter the SSID and click on Next to continue. After all of the WAN configurations have been made, the WAN Setup Summary screen displays all WAN settings that you have made. Check that the settings are correct before clicking on the Save / Reboot button. Clicking on Save / Reboot will save your settings and restart your router. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Advanced Setup This section of the setup is an advanced version of the quick setup. If you want to make specific configurations to your router such as firewall, port mapping, quality of service, DNS, etc., consider going through this advanced setup for a more comprehensive configuration. WAN Configure the WAN settings as provided by your ISP. Click on the Add button if you want to add a new connection for the WAN interface. The ATM PVC Configuration screen follows as seen below.
Find out the following values from your ISP before you change them. x x x VPI: Virtual Path Identifier. The valid range is 0 to 255. VCI: Virtual Channel Identifier. The valid range is 32 to 65535. Service Category: Five classes of traffic are listed— o UBR Without PCR (Unspecified Bit Rate without Peak Cell Rate)— UBR service is suitable for applications that can tolerate variable delays and some cell losses.
After you click on Next, the below screen appears allowing you disable the bridge service if desired. When the settings are complete, the next screen shows a WAN Setup – Summary screen displaying the WAN configurations made. Click on Save to save the settings. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
After the settings are saved, the below screen will follow displaying the WAN settings that you made with the option to Add or Remove any of the connections that you have made. When satisfied with the settings click on the Finish button. After selecting the Finish button, the below screen will appear. At this point, the router will reboot to save the changes made. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
LAN Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond to your LAN’s IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers. Disable the DHCP server if you would like to manually assign IP addresses. Click on Next to continue.
Ethernet Mode Ethernet mode allows you to select the speed of your Ethernet connection. Modes include—auto, 100 full, 100 half, 10 full and 10 half. If you select “auto” then the router will use the common mode that all the connected interfaces can operate at. NAT If you enable NAT (Network Address Translation), you can configure the Virtual Server, Port Triggering, and DMZ Host.
Select the virtual server from the drop-down list and complete the server IP address, then click on the Save / Apply button. The following screen appears after you save your selection. To add additional virtual servers, click on the Add button. If you need to remove any of the server names, select the check box and click on the Remove button. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Port Triggering Click on the Add button to add Port Triggering to your Internet application. The below screen appears when you click on Add allowing you to select the application that you want to set the port settings for. After a selection has been made, click on the Save / Apply button. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
The below screen appears after you save your selections. You will be able to add or remove selections made by clicking on the Add and Remove buttons. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save / Apply. ALG ALG, Application Layer Gateway can be used to allow firewall traversal with SIP. To enable voice packets to successfully pass through firewalls and NATs, click on the SIP enabled checkbox. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
Firewall IP Filtering—Outgoing The outgoing filter will block the LAN traffic from entering the WAN side. Click on the Add button to create filters. The below screen will appear when you click on Add. Input the filter name, source information (from the LAN side), and destination information (from the WAN side). Then click on Save / Apply. The following screen appears when you Save / Apply the IP filter. The screen lists the IP filters that were added from the previous screen.
IP Filtering—Incoming Incoming IP filter filters the WAN traffic to the LAN side. Click on the Add button to add incoming filter settings. Enter a filter name, information about the source address (from the WAN side), and information about the destination address (to the LAN side). Select the protocol and WAN interface, then click on Save/Apply to add the setting. You can view and delete the incoming filter settings from this screen. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. If you click on Change Policy, a confirmation dialog allows you to verify your change. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save / Apply to save it. After you save the settings, a screen showing the settings will appear. On this screen you will be able to view and delete MAC filtering rules. Parental Control In a home setting, parents can also restrict the day of the week certain computers can access the router.
After you click you Add, you will see the below screen. You will be able to enter the MAC address of the PC that you wish to place on a time of day restriction. Click on Save / Apply to save the settings and to continue. Zhone 4-Port Wireless Ethernet Router User Manual Version 1.
