Motherboard A8V-E Deluxe
E1781 First Edition December 2004 Copyright © 2004 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ............................................................................................... vii Safety information ............................................................................ viii About this guide ................................................................................. ix How this guide is organized .................................................... ix Where to find more information ..............................................
Contents 2.5.3 Interrupt assignments .......................................... 2-17 2.5.4 PCI slots ................................................................ 2-18 2.5.5 PCI Express x16 slot ............................................. 2-18 2.5.6 PCI Express x1 slot ............................................... 2-18 2.6 Jumpers .............................................................................. 2-19 2.7 Connectors ..............................................................
Contents 4.3 4.4 Main menu .......................................................................... 4-15 4.3.1 System Time ......................................................... 4-15 4.3.2 System Date ......................................................... 4-15 4.3.3 Language .............................................................. 4-15 4.3.4 Legacy Diskette A ................................................ 4-15 4.3.5 Primary and Secondary IDE Master/Slave ............. 4-16 4.3.
Contents 5.3 5.2.1 Running the support CD ......................................... 5-1 5.2.2 Drivers menu .......................................................... 5-2 5.2.3 Utilities menu .......................................................... 5-4 5.2.4 ASUS Contact information ...................................... 5-6 5.2.5 Other information ................................................... 5-6 Software information ........................................................... 5-9 5.3.
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
A8V-E Deluxe specifications summary CPU Socket 939 for AMD Athlon™ 64FX/AMD Athlon™ 64 processor Supports AMD 64 architecture that enables simultaneous 32-bit and 64-bit architecture Supports AMD Cool ‘n’ Quiet! Technology Chipset Northbridge: VIA® K8T890 Southbridge: VIA® VT8237R System Bus 2000 MT/s Memory Dual-channel memory architecture 4 x 184-pin DIMM sockets support ECC/non-ECC unbufferred 400/333/266 MHz DDR memory modules Supports up to 4 GB system memory Expansion slots 1 x PCI Express x1
A8V-E Deluxe specifications summary AI Overclocking ASUS AI Overclocking (Intelligent CPU frequency tuner) ASUS C.P.R. (CPU Parameter Recall) ASUS JumperFree CPU, Memory, and chipset voltage adjustable Stepless Frequency Selection(SFS) from 200 MHz up to 400 MHz at 1 MHz increment Special features ASUS Wi-Fi@HOME ASUS Post Reporter™ ASUS Q-Fan2 ASUS CrashFree BIOS 2 ASUS Multi-language BIOS ASUS MyLogo2 ASUS Instant Music BIOS features 4 MB Flash ROM, Phoenix-Award BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.
A8V-E Deluxe specifications summary Power Requirement ATX power supply (with 24-pin and 4-pin 12 V plugs) ATX 12 V 2.0 compliant Form Factor ATX form factor: 12 in x 9.6 in (30.5 cm x 24.4 cm) Support CD contents Device drivers ASUS PC Probe ASUS Live Update Utility Antivirus software (OEM version) WiFi-g™ One-touch wizard *Specifications are subject to change without notice.
xiv
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® A 8 V - E D e l u x e m o t h e r b o a r d ! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The AMD Athlon™ 64FX and Athlon™ 64 desktop processors are based on AMD’s 64-bit and 32-bit architecture, which represents the landmark introduction of the industry’s first x86-64 technology. These processors provide a dramatic leap forward in compatibility, performance, investment protection, and reduced total cost of ownership and development. See page 2-6.
PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to-point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI specifications. See page 2-18 for details.
Temperature, fan, and voltage monitoring The CPU temperature is monitored by the ASIC (integrated in the Winbond Super I/O) to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection. The ASIC monitors the voltage levels to ensure stable supply of current for critical components. See section “4.5.4 Hardware Monitor” on page 4-36. 1.3.2 ASUS Proactive features ASUS WiFi-g™ ASUS WiFi-g™ is an IEEE 802.
1.3.3 Innovative ASUS features Precision Tweaker Designed for overclocking aficionados, this feature allows you to gradually increase the CPU and memory voltage to achieve maximum system performance. PEG Link mode This feature allows you to adjust the PCI Express graphics frequency according to your system configuration for optimized graphics performance. CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted.
ASUS MyLogo2™ This new feature present in the motherboard allows you to personalize and add style to your system with customizable boot logos. See page 5-9 for details. ASUS Instant Music This unique feature allows you to playback audio files even without booting the system to Windows™. Just press the ASUS Instant Music special function keys and enjoy the music! See page 4-32 for details.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-6 2.4 System memory ................................................................. 2-10 2.5 Expansion slots ................................................................... 2-14 2.6 Jumpers ...........................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 Motherboard layout 24.5cm (9.6in) ATX12V Top:Line In Center:Line Out Bottom:Mic In FLOPPY EATXPWR VIA WL_LED K8T890 Marvell 88E8053 PCIEX1_1 PRI_IDE SEC_IDE WL_ANT 30.5cm (12.
2.2.4 2-4 Layout Contents Slots Page 1. DDR DIMM slots 2-11 2. PCI slots 2-18 3. PCI Express x16 slot 2-18 4. PCI Express x1 slot 2-18 Jumpers Page 1. Clear RTC RAM (3-pin CLRTC) 2-19 2. USB Device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) 2-19 3. Keyboard power (3-pin KBPWR) 2-19 Rear panel connectors Page 1. Parallel port 2-22 2. IEEE 1394 port 2-22 3. RJ-45 port 2-22 4. Rear Speaker Out port (gray) 2-22 5. Side Speaker Out port (black) 2-22 6.
Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-24 2. Primary IDE connector (40-1 pin PRI_IDE) 2-24 3. Secondary IDE connector (40-1 pin SEC_IDE) 2-24 4. Serial ATA connectors (7-pin SATA1, SATA2) 2-25 5. CPU fan connector (4-pin CPU_FAN) 2-26 6. Power fan connector (3-pin CHIP_FAN) 2-26 7. Chassis fan connector (3-pin CHA_FAN1) 2-26 8. Chassis fan 2 connector (3-pin CHA_FAN2) 2-26 9. Serial port connector (10-1 pin COM1) 2-27 10.
2.3 Central Processing Unit (CPU) 2.3.1 Overview The motherboard comes with a surface mount 939-pin Zero Insertion Force (ZIF) socket designed for the AMD Athlon™ 64FX or AMD Athlon 64™ processor. The 128-bit-wide data paths of these processors can run applications faster than processors with only 32-bit or 64-bit wide data paths. Take note of the marked corner (with gold triangle) on the CPU. This mark should match a specific corner on the socket to ensure correct installation. Gold triangle 2.3.
2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°-100° angle. Socket Lever Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely. 3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it fits in place. Gold triangle Small triangle The CPU fits only in one correct orientation.
2.3.3 Installing the heatsink and fan The AMD Athlon™ 64FX or AMD Athlon 64™ processor require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan. 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base. • The retention module base is already installed on the motherboard upon purchase.
2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place. Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base, otherwise you cannot snap the retention bracket in place. 4.
3. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. Rotation +12V GND CPU_FAN A8V-E DELUXE ® A8V-E DELUXE CPU_Fan connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector. 2.4 System memory 2.4.1 Overview The motherboard comes with four 184-pin Double Data Rate (DDR) Dual Inline Memory Modules (DIMM) sockets.
2.4.2 Memory Configurations You may install 256 MB, 512 MB and 1 GB unbuffered ECC or non-ECC DDR DIMMs into the DIMM sockets using the memory configurations in this section. • For dual-channel configuration, the total size of memory module(s) installed per channel must be the same for better performance (DIMM_A1+DIMM_A2=DIMM_B1+DIMM_B2). • Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor.
Size Vendor 256MB 256MB 512MB 256MB 512MB 1024MB 512MB 256MB 256MB 512MB 256MB 512MB 512MB 256MB 256MB 512MB 256MB 512MB 256MB 512MB 512MB 1024MB 256MB 512MB 256MB 256MB 512MB 256MB 512MB 256MB 512MB TwinMOS TwinMOS TwinMOS Transcend Transcend Transcend Transcend Transcend Apacer Apacer Apacer Apacer A DATA A DATA A DATA A DATA Winbond Winbond KINGMAX KINGMAX ATP ATP NANYA NANYA BRAIN POWER ProMOS ProMOS Deutron Deutron Novax Novax Model M2G9I08AIATT9F081AADT M2G9I08A8ATT9F081AADT M2G9J16A8ATT9F081AADT
2.4.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. DDR DIMM notch 1 1 Unlocked retaining clip A DDR DIMM is keyed with a notch so that it fits in only one direction.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.5 PCI Express x16 slot This motherboard supports PCI Express x16 graphic cards that comply with the PCI Express specifications. The figure shows a graphics card installed on the PCI Express x16 slot. 2.5.
2.6 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 3 4 5 6 7 17 16 15 14 13 12 11 10 9 8 1. P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. 2. I E E E 1 3 9 4 a p o r t . This 6-pin IEEE 1394 port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. L A N R J - 4 5 p o r t . This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.
8. W i F i - g ™ a n t e n n a p o r t . This port connects to the optional dipolar antenna for the onboard ASUS WiFi-g™ solution. (Wireless Edition only ) W i r e l e s s L A N d a t a t r a n s m i s s i o n L E D . This green A I R LED indicates the data transmission status of the onboard wireless LAN adapter. Refer to the table below for the LED indications. 9. Wireless LAN LED indications Status Indication On The onboard WiFi-g™ is on but has no data activity.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. The Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND 3. A8V-E DELUXE SATA2 SATA1 GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND R A8V-E DELUXE SATA connectors Important notes on Serial ATA • The Serial ATA RAID feature (RAID 0, RAID 1) is available only if you are using Windows® 2000/XP.
4. CPU, Chassis, and Power fan connectors (3-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHIP_FAN, CHA_FAN2) The fan connectors support cooling fans of 350mA~2000mA (24 W max.) or a total of 1A~3.48A (41.76 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. • Do not forget to connect the fan cables to the fan connectors.
5. Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. COM1 A8V-E DELUXE PIN 1 ® A8V-E DELUXE COM port connector 6. USB connectors (10-1 pin USB56, USB78) A8V-E DELUXE USB78 1 A8V-E DELUXE USB 2.
7. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Use of an ATX 12 V Specification 2.0-compliant power supply unit (PSU) that provides a minimum power of 350 W is recommended for a fully-configured system.
8. Internal audio connectors (4-pin CD, AUX) Right Audio Channel Ground Ground Left Audio Channel Right Audio Channel Ground Ground Left Audio Channel These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV-tuner, or MPEG card. AUX CD A8V-E DELUXE ® A8V-E DELUXE Internal audio connectors 9. GAME/MIDI port connector (16-1 pin GAME) This connector is for a GAME/MIDI port.
1 0 . Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
Line out_L NC Line out_R MICPWR MIC2 1 2 . Front panel audio connector (10-1 pin FP_AUDIO) This connector is for a chassis-mounted front panel audio I/O module that supports legacy AC ‘97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. BLINE_OUT_R +5VA AGND FP_AUDIO BLINE_OUT_L A8V-E DELUXE ® A8V-E DELUXE Front panel audio connector GND GND SPDIF_IN +5V SPDIF_OUT 1 3 .
1 4 . System panel connector (20-pin PANEL) This connector supports several chassis-mounted functions. +5V Ground Ground Speaker SPEAKER PLED- PLED+ PLED A8V-E DELUXE IDE LED Reset Ground IDE_LED+ IDE_LED- ExtSMI# Ground PWR Ground PANEL RESET ® SMI PWR * Requires an ATX power supply. A8V-E DELUXE System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer .................................................. 3-2 3.3 ASUS POST Reporter™ ..........................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® XP: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
3.3 ASUS POST Reporter™ This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter™. This feature lets you hear vocal messages during POST that alerts you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem. These POST messages are customizable using the Winbond Voice Editor software that came with your package. You can record your own messages to replace the default messages. 3.3.
POST Message Action CPU temperature too high • Check if the CPU fan is working properly. CPU fan failed • Check the CPU fan and make sure it turns on after you apply power to the system. • Make sure that your CPU fan supports the fan speed detection function. • Check your power supply and make sure it is not defective. • Call ASUS technical support for assistance. See the “ASUS contact information” on the inside front cover of this user guide.
3.3.2 Winbond Voice Editor The Winbond Voice Editor software allows you to customize the vocal POST messages. You can install this application from the support CD. To avoid conflicts, do not run the Winbond Voice Editor while running the ASUS PC Probe application. Launching the Voice Editor You can launch the program from the Windows® desktop by clicking S t a r t > A l l P r o g r a m s > W i n b o n d V o i c e E d i t o r > V o i c e E d i t o rr. The Winbond Voice Editor screen appears.
Changing the default language To change the default language: 1. Click the L o a d button from the Voice Editor main window. A window with the available languages appears. 2. Select your desired language, then click O p e n n. The event messages for the language you selected appear on the Voice Editor main window. Not all events on some languages have a corresponding message due to file size constraints. 3. Click the W r i t e button from the Voice Editor main window to update the EEPROM. 4.
Customizing your POST messages The Voice Editor application allows you to record your own POST messages if your language is not supported or if you wish to to replace the pre-installed wave files. To customize your POST messages. 1. Launch the Voice Editor application and note the list of POST events on the leftmost column of the screen. 2. Prepare your message for each event. 3. Use a recording software (e.g. Windows® Recorder) to record your messages, then save the messages as wave files (.WAV). 4.
6. Select a POST event on the Voice Editor main window, then click the E d i t button. The E v e n t S o u n d E d i t o r window appears. 7. Locate and select your wave file for the event, then click on the arrow opposite Voice1. The file you select appears on the space next to it. 8. Click O K to return to the Voice Editor main window. 9. Do steps 6 to 8 for the other events. 10. When done, click S a v e e. A window appears prompting you to save your configuration. 11. Type a file name with an .
