Listening to music using the stereo headphones GAVDP A2DP AVRCP This section describes how to use the stereo headphones to listen to your favourite music or other audio files stored on your PC. Configuring the stereo headphones Connecting to the stereo headphones Listening to music or other audio files Playing music using remote control Copyright protection function Configuring the stereo headphones Procedure 1. Right-click on the Bluetooth icon in the task tray, and click on [Add New Connection].
The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] will appear. 2. Switch ON the stereo headphones and activate "Discoverable" mode Please refer to the user guide for the stereo headphones for further information on how to operate them. 3. Confirm that [Express Mode] has been selected, and then click on the [Next] button The [Add New Connection Wizard (Searching for Bluetooth Devices)] screen will appear.
Once the search for the devices has ended, the [Add New Connection Wizard (Select Device)] screen will appear. 4. Select the device name of the stereo headphones from the list, and click on the [Next] button The [Add New Connection Wizard (Searching for Services)] screen will appear. 5. Configure the type and name of the icon to appear once registration is complete, and click on the [Next] button Please click the [Next] button once you are satisfied with the configuration.
The [Add New Connection Wizard (Configure Connection Name)] screen will appear. 6. Click on the [Finish] button The settings will be registered, and the icon will appear on the [Bluetooth Settings] screen. Connecting to the stereo headphones You can connect to the stereo headphones from the icon registered in [Bluetooth Settings]. Please refer to the user guide for information on how to make a connection from the stereo headphones.
Listening to music or other audio files 1. Playing music or other audio files on your PC Important o Please confirm the points below if you are unable to hear anything despite having properly connected the stereo headphones. Click [Start] [All Programs] [Accessories] o o o [Entertainment] [Volume Control]. Remove the tick next to [Mute] if it has been ticked. If the volume is at its lowest setting, please adjust it to an appropriate level.
1. Right-click on the icon for the currently connected mode from [Bluetooth Settings] on your PC, and click on "Disconnect." A message confirming the disconnection may appear. 2. Click on the "Yes" button after having followed the instructions in the message. The icon will indicate that the device has been disconnected.
The procedure below can be performed in order to change the position where the receive command is displayed or to not have the command displayed. Procedure 1. Double-click on the Bluetooth icon in the taskbar Launches "Bluetooth Settings." 2. Click on [Bluetooth] [Select AV Player] from the menu bar. The [Select AV Player] screen will appear. 3. Select the appropriate item from the pull-down menu of positions where the receive command is to be displayed, and then click on the [OK] button.
• • • • Right Select Root menu Angle Copyright protection function A copyright protection function is supported according to the SCMS-T format as defined in the Bluetooth specifications. Follow the configuration procedure below to establish connections only with devices that support this function. Procedure 1. Double-click on the Bluetooth icon in the task tray. Launches "Bluetooth Settings." 2. Select [Bluetooth] from the menu, and click on [Copyright Protection Setting].
Using a wireless keyboard [HID] This section describes how to connect a Bluetooth-compatible keyboard to a PC. Setting up the wireless keyboard Procedure 1. Right-click on the Bluetooth icon in the task tray, and then click on [Add New Connection] Note o Alternatively, click [Start] [All Programs] [Bluetooth] [Bluetooth Settings], and then click on [New Connection] from the active [Bluetooth Settings] window. The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)] window will appear.
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear. Once the program has finished searching for the devices, the [Add New Connection Wizard (Device Selection)] window will appear. 3.
The [Add New Connection Wizard (Searching for Services)] window will appear. 4.
Once the program has detected the services successfully, connection to the device and registration of settings information will be performed automatically. The [Add New Connection Wizard (Connection Name Settings)] window will appear. 5. Enter the type and name of the icon displayed after registration, and then click on the [Next] button Please click on the [Next] button if you are satisfied with the settings.
Note o You can change the connection icon and icon name. "Changing a connection icon name" "Changing a connection icon" The [Add New Connection Wizard (Completing the Add New Connection Wizard)] window will appear. 6. Click on the [Finish] button The settings information will be registered, and an icon will appear in the [Bluetooth Settings] window. Note • Pressing any key on the wireless keyboard will automatically connect it to the PC thereafter.
Using a wireless mouse [HID] This section describes how to connect a Bluetooth-compatible mouse to a PC. Setting up the wireless mouse Procedure 1. Turn on the wireless mouse, and set it to be connectable via Bluetooth Please refer to the instruction manual for details on how to operate the mouse. 2.
3. Confirm that [Express Mode] has been selected, and then click on the [Next] button The [Add New Connection Wizard (Searching for Bluetooth devices)] window will appear. Once the program has finished searching for the devices, the [Add New Connection Wizard (Device Selection)] window will appear.
4. Select the device name of the mouse from [Device List], and then click on the [Next] button The [Add New Connection Wizard (Searching for Services)] window will appear. A message confirming a device connection will appear. 5.
The [Add New Connection Wizard (Connection Name Settings)] window will appear. 6. Enter the type and name of the icon displayed after registration, and then click on the [Next] button Please click on the [Next] button if you are satisfied with the settings. Note o Please use this window to change the connection name and icon. - Changing the connection icon name - Changing the connection icon The [Add New Connection Wizard (Completing the Add New Connection Wizard)] window will appear. 7.
Note o Clicking on one of the mouse buttons or otherwise operating it will automatically connect it to the PC thereafter. Please connect manually if automatic connection is unsuccessful.
Exchanging files with a PC or PDA [FTP] You can send and receive files other than business card data with a Bluetooth-enabled PC or PDA. Use "File transfer" in the Bluetooth Information Exchanger to exchange files. Note • • The same operations will be valid as long as the PC and PDA support the FTP profile. "File transfer" cannot be used to send or receive business card data. Please instead use "Object Push" to perform these activities.
o Alternatively, opening Explorer and clicking on the Bluetooth Information Exchanger folder will produce the same result. The [Bluetooth Information Exchanger] window will appear. 3. Double-click on the [File transfer] icon A list of devices will appear in the [File transfer] window.
Note If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. o You can also use "Image transfer" when sending individual image files. 4. Use the mouse to drag and drop the file you wish to send over the destination icon In this case, the file will be sent to a PC named "PC-1". o Note When using "File transfer", you can send individual files as well as entire folders. 5.
If the file has been sent successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the file transmission was unsuccessful. Please click on the [OK] button to close the message, and repeat the procedure. Note o o Files that have been sent will be saved in a file transfer shared folder on the destination device.
o You can use Properties in the Bluetooth Information Exchanger to change the location of the "Shared folder" on the hard drive. Sending files to a PC or PDA (by right-clicking the mouse) 1. Turn on the PC or PDA Confirm that a Bluetooth connection has been enabled before proceeding. 2.
Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [to Bluetooth] [Search other devices]. Once the devices have been detected, the message below will appear. Please select the destination device, and then click on the [Send] button.
3. Confirm that the file is being sent The file will be sent to the PC. Note o When sending files using "File transfer", a message requesting permission to receive the files may appear on the destination (receiving) device. The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided. If you are using the Bluetooth Utility, a message similar to the one below will appear.
If the file has been sent successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the file transmission was unsuccessful. Please click on the [OK] button to close the message, and then repeat the procedure. Note o Files that have been sent will be saved in a file transfer shared folder on the destination device. Receiving files from a PC or PDA Your PC is able to receive files that have been saved in the shared folder on the destination PC or PDA.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop Note o Alternatively, opening Explorer and clicking on the Bluetooth Information Exchanger folder will produce the same result. The [Bluetooth Information Exchanger] window will appear. 3. Double-click on the [File transfer] icon A list of devices will appear in the [File transfer] window.
In this case, the file will be received from the PDA named "My Mobile". 4. Double-click on the [PDA-1] icon The file saved in the shared folder in "My Mobile" will appear. 5. Right-click on the file you wish to receive, and then select "Receive file". The file will be received from a PDA.
o With "File transfer", you can send individual files as well as entire folders. Please right-click on the folder you wish to receive, and select "Receive folder". Subsequent operations should be performed in the same manner as when receiving individual files. If the file has been received successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the file transmission was unsuccessful.
You can use Properties under the Bluetooth Information Exchanger to specify the location of the "Shared folder" on the hard drive.
Sending images to a mobile telephone [BIP] You can send image data to a Bluetooth-compatible mobile telephone. Large images will be automatically reduced to fit on the telephone display screen. Images are sent using "Image transfer" under Bluetooth Information Exchanger. Note • • The mobile telephone must support the BIP profile. The following image file formats can be sent and received using "Image transfer": o Bitmap (*.bmp) o JPEG (*.jpg, *.jpeg) o PNG (*.
o Alternatively, opening Explorer and clicking on the Bluetooth Information Exchanger folder will produce the same result. The [Bluetooth Information Exchanger] window will appear. 3. Double-click on the [Image transfer] icon A list of devices will appear in the [Image transfer] window.
If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. 4. Drag and drop the file you wish to send over the destination icon In this case, the image will be sent to a mobile telephone named "BT-Phone-1". o The image will be sent. If the image has been sent successfully, the message below will appear. Please click on the [OK] button.
Sending images to a mobile telephone (by right-clicking the mouse) 1. Turn on the mobile telephone Confirm that a Bluetooth connection has been enabled before proceeding. 2. Right-click on the file you wish to send, and then click on its destination from [to Bluetooth] Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [to Bluetooth] [Search other devices]. Once the devices have been detected, the message below will appear.
The image will be sent. If the image has been sent successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the image transmission was unsuccessful. Please click on the [OK] button to close the message, and repeat the procedure.
Sending images to a PC or PDA [BIP] You can send image data to a Bluetooth-enabled PC or PDA. Images are sent using "Image transfer" under Bluetooth Information Exchanger. Note • The following image file formats can be sent and received using "Image transfer": o Bitmap (*.bmp) o JPEG (*.jpg, *.jpeg) o PNG (*.png) Sending images to a PC or PDA (using icons) Sending images to a PC or PDA (by right-clicking the mouse) Procedure Sending images to a PC or PDA (using icons) 1.
The [Bluetooth Information Exchanger] window will appear. 3. Double-click on the [Image transfer] icon A list of devices will appear in the [Image transfer] window. Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed.
4. Drag and drop the file you wish to send over the destination icon In this case, the image will be sent to a PC named "PC-1". The image will be sent. If the image has been sent successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the image transmission was unsuccessful. Please click on the [OK] button to close the message, and repeat the procedure.
o o o Images that have been sent will be saved in an image transfer folder on the destination device. Images received using "Image transfer" in the Bluetooth Information Exchanger will be saved in the "Image Box" in "Image transfer". You can use Properties under the Bluetooth Information Exchanger to change the location of the "Image Box" folder on the hard drive. Sending images to a PC or PDA (by right-clicking the mouse) 1.
Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [to Bluetooth] [Search other devices]. Once the devices have been detected, the message below will appear. Please select the destination device, and then click on the [Send] button.
The image will be sent. If the image has been sent successfully, the message below will appear. Please click on the [OK] button. The message below will appear if the image transmission was unsuccessful. Please click on the [OK] button to close the message, and repeat the procedure.
Note o When you send images by right-clicking the mouse, the image data that has been sent will be saved in the image transfer shared folder on the destination device. This is also the case when you send images using icons.
Exchanging business card data with a PC or PDA [OPP] You can exchange business card data with a Bluetooth-enabled PC or PDA. Business card data are exchanged using "Object Push" under Bluetooth Information Exchanger. Note • • • • Data compliant with the "vCARD" standard are the only type of business card data able to be sent and received with "Object Push". Business card data can be used by applications such as Microsoft Outlook.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop Note o Alternatively, opening Explorer and clicking on the Bluetooth Information Exchanger folder will produce the same result. The [Bluetooth Information Exchanger] window will appear. 3. Double-click on the [Object Push] icon A list of devices will appear in the [Object Push] window.
Note If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. 4. Use the mouse to drag and drop the business card you wish to send over the destination icon In this case, the business card will be sent to a PC named "PC-1". o The business card will be sent.
o When you try to send a business card, a message requesting permission to receive the card may appear on the device belonging to the other party (i.e., on the receiving end). The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided. If you are using the Bluetooth Utility, a message similar to the one below will appear. If the business card has been sent successfully, the message below will appear.
You can use Properties under Bluetooth Information Exchanger to configure whether or not you would like such an application to start automatically. Selecting a business card and sending it to a PC or PDA (by right-clicking the mouse) 1. Turn on the PC or PDA Confirm that a Bluetooth connection has been enabled before proceeding. 2.
Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [to Bluetooth] [Search other devices]. Once the devices have been detected, the message below will appear. Please select the destination device, and then click on the [Send] button. The business card will be sent.
o When you try to send a business card, a message requesting permission to receive the files may appear on the device belonging to the other party (i.e., on the receiving end). The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided. If you are using the Bluetooth Utility, a message similar to the one below will appear. If the business card has been sent successfully, the message below will appear.
You can prepare a business card bearing your name and other details such as your company and telephone numbers, and then send it to another party. Note • • Please use Properties under Bluetooth Information Exchanger beforehand to configure which data to use for your own business card. You can only have one business card registered as your own that is able to be sent. 1. Turn on the PC or PDA Confirm that a Bluetooth connection has been enabled before proceeding 2.
3. Double-click on the [Object Push] icon A list of devices will appear in the [Object Push] window. Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. 4. Right-click on the destination icon, and then click on [Send business card To] In this case, your personal business card will be sent to a PC named "PC-1".
The business card will be sent. Note o When you try to send a business card, a message requesting permission to receive the files may appear on the device belonging to the other party (i.e., on the receiving end). The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided. If you are using the Bluetooth Utility, a message similar to the one below will appear.
o Data that has been sent will be saved in a folder for exchanged business cards on the destination device. Acquiring a business card from another party You can use your PC to acquire a business card from a party containing their details. 1. Turn on the PC or PDA Confirm that a Bluetooth connection has been enabled before proceeding 2.
Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. 4. Right-click on the icon of the party whose card you wish to acquire, and then click on [Receive business card] In this case, the business card of the other party will be acquired from a PC named "PC-1".
The business card will be received. Note o When you try to acquire a business card, a message requesting permission to send the files may appear on the device belonging to the other party (i.e., on the sending end). The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided. If you are using the Bluetooth Utility, a message similar to the one below will appear.
Exchanging business cards Simultaneously exchange your business card with one belonging to another party. 1. Turn on the PC or PDA Confirm that a Bluetooth connection has been enabled before proceeding. 2. Double-click on the Bluetooth Information Exchanger icon on the Desktop Note o Alternatively, opening Explorer and clicking on the Bluetooth Information Exchanger folder will produce the same result. The [Bluetooth Information Exchanger] window will appear. 3.
Note o If the desired device does not appear in the list, please confirm that the device has been turned on, and then select [Bluetooth] [Search Devices]. A device search will be performed. 4. Right-click on the icon of the party with whom you wish to exchange business cards, and then click on [Object Push] In this case, the business cards will be exchanged with a PC named "PC-1".
The business card from the party who executed the "Exchange business cards" command will be sent first. Note o When you try to send a business card, a message requesting permission to receive the files may appear on the device belonging to the other party (i.e., on the receiving end). The content of the message will vary with the Bluetooth software installed on the destination device, so please be sure to follow the instructions provided.
A message of confirmation will appear if the card has been successfully received. Note o Business cards that have been received will be saved in the "Inbox" under "Object Push". You can use Properties under the Bluetooth Information Exchanger to set the location of the Inbox on the hard drive.
Creating business card data in the vCARD format This section describes how to create business card data in the vCARD format using Microsoft Outlook 2002. Important • The method for creating business card data will differ according to the type and version of application used. Please refer to the application user guide for details. Procedure 1. Start Outlook, and then click on the [Contacts] icon. The list of your contacts will appear. 2.
3. In the [vCard file] dialog box, specify the file name and save destination, and then click on the [Save] button. A vCARD file will have been created in the specified location.
Using a Bluetooth-compatible camera [BIP] By connecting a Bluetooth-compatible digital camera to your PC via Bluetooth, you will be able to operate the camera shutter from the PC and transmit the captured images to it as well. Connecting the camera Taking pictures Viewing images saved on your PC Connecting the camera Use the "Remote Camera" tool in the Bluetooth Utility to connect the camera to your PC. Procedure 1.
Different cameras are operated in different ways, depending on the manufacturer and model used. Please refer to the instruction manual for further details on how to operate your camera. 3. Click on the [Camera Search...] button o The camera will be detected and its icon displayed.
4. Right-click on the camera icon, and select [Connect] The camera will be connected, and images from the camera will appear on-screen. Taking pictures By placing the mouse cursor over the on-screen image, the camera's operating window will appear. You can operate the camera from this window.
1. Click on the button in the operating window. A single image will be captured and sent to the PC. Taking several consecutive frames button in the operating window 1. Click on the A succession of images will be captured and sent to the PC. Note o o The remote camera shutter cannot be operated while the camera is connected to the PC.
1. [Bluetooth] In the [Remote Camera] window, click on [Properties] [Consecutive Image Settings] The [Change number of consecutive images] dialog box will appear 2. Click on the [<][>] buttons to select the number of consecutive images to be captured Important o o Images are not only sent to the PC, but are stored in the camera's on-board memory as well. Please be aware of the remaining memory capacity when you are taking a large number of pictures.
Note • This window is an example showing pictures when [Filmstrip] has been selected from the [View] menu in Explorer.
Using a headset to communicate [HSP] This section provides a description of how to use a Bluetooth-compatible wireless headset to communicate (chat) using Microsoft NetMeeting or other software. Registering the headset Making a connection to the headset Disconnecting from the headset Registering the headset Procedure 1.
2. Turn the headset power on Once you have turned on the headset, set the mode to enable a Bluetooth connection. Important The procedure for operating the headset may differ depending on the manufacturer and model. Please consult your user guide for a detailed description of how to operate the unit. 3. Confirm that [Express Mode] has been selected, then click on the [Next] button o The [Add New Connection Wizard (Searching for Bluetooth Devices)] screen will appear.
