User's Manual for Tapeless Digital Answering System Telephone with Time/Day 1815 Fold open this manual for information about this telephone's installation and operation. Please read Part 1 — Important Product Information, included in this package. Part 2 © 1998 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico.
I N S T A L L A T I O N Battery Installation (optional) RING SELECT POWER Telephone Line Cord FOR TABLE/DESK INSTALLATION 1 Install the batteries (optional). • Turn the unit upside down. • Push in on the two tabs at the large end of the base, and lift the base off the unit. • Push in on the two tabs on the battery compartment door, and remove it. • Insert four AA batteries. Always use four new batteries. • Replace the battery compartment door. • Reattach the base by inserting the tabs into the slots.
I N S T A L L A T I O N Reverse the Handset Tab 1 2 3 PULL TABS TO OPEN PULL TABS TO OPEN PULL TABS TO OPEN Figure 1 Figure 2 Figure 3 FOR WALL INSTALLATION 1 2 3 Reverse the handset tab. (This tab holds the handset when you hang up.) Hold down the switchhook, and slide the tab up and out of its slot. Turn the tab so that the end with the “hook” is up. Then insert the tab back into its slot. Remove the base. Push in on the two tabs at the large end of the base, and lift the base off the unit.
T E L E P H O N E O P E R A T I O N Dial Mode Mute This phone comes set to operate with touch tone service. If you have dial pulse (rotary) service, you will need to reset the dial mode. If you hear clicks (not tones) when you dial, you have dial pulse (rotary) service. Mute lets you hear the other party, but prevents the other party from hearing you. To change to dial pulse mode: 1 Press and release G. 2 Press #, #, #, 3. To mute a call, press and release m. The MUTE light goes on.
T E L E P H O N E M E M O R Y Light is on when phone line is in use. When light goes on, battery needs to be replaced. Access telephone subscriber services. Store a pause in a memory dialing number. Put caller on Hold. (Light goes on when call is on Hold.) Dial numbers in telephone memory. Mute handset microphone. Store numbers in telephone memory. Redial last number called. Adjust listening volume during a call.
ANSWERING SYSTEM OPERATION Select number of times line rings before system answers (RING SELECT on back). Set and hear Remote Access Code. Use with other buttons to change settings. Displays number of messages and other indicators. Set and hear time/day. Turn system on or off. Record and hear outgoing announcement. Repeat all or part of a message. Play messages. Stop message playback. Delete all or selected messages. Skip all or part of a message. Adjust listening volume during message playback.
ANSWERING SYSTEM OPERATION Repeat entire message — Press and release ?. Repeat part of message — Hold down ? for a few seconds, then release it to resume playing. The system beeps while the button is held down. Skip to next message — Press and release /. Skip part of a message — Hold down / for a few seconds, then release it to resume playing. The system beeps while the button is held down. Stop message playback — Press and release S.
ANSWERING SYSTEM OPERATION Recording a Memo You can record a memo to be stored as an incoming message. The memo can be up to 3 minutes long, and will be played back with other messages. 1 Press and release M. After the beep, speak toward the microphone. 2 To stop recording, press S. When Memory is Full The system can record approximately 12 minutes of messages, including your announcement, for up to a total of 99 messages.
ANSWERING SYSTEM OPERATION From a Remote Touch Tone Phone Playing Messages 1 2 3 4 Dial your telephone number from a touch tone phone. When the system answers, enter your Remote Access Code. The system announces the number of messages received, then beeps twice. After the two beeps, wait 4 seconds, and the system plays back messages — OR — Press and release 1 to play all messages — OR — Press and release 2 to play only new messages (if there are no new messages, the system announces “No new messages”).
IN CASE OF If this answering system does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 222–3111. D I F F I C U LT Y Messages Are Incomplete • No Dial Tone • • • Make sure all plugs are connected properly. Check the line cord connections at the wall jack and at the telephone. Also check the coiled cord connections at both ends. Unplug the telephone and connect it to another wall jack.
© 1999 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico. 848229605 Issue 2AT&T © 1999 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico.
REMOTE COMMAND PRESS REMOTE COMMAND PRESS Play all messages 1 Play all messages 1 Play only new messages 2 Play only new messages 2 Repeat message 4 while message is playing Repeat message 4 while message is playing Skip message 6 while message is playing Skip message 6 while message is playing Delete all messages 3, 3 Delete all messages 3, 3 Delete selected message 3 while message is playing Delete selected message 3 while message is playing Record announcement 7, *, speak, pr
I N S T A L L A T I O N I N S T A L L A T I O N IN OF If this answering system does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 222–3111. Reverse the Handset Tab Battery Installation (optional) CASE D I F F I C U LT Y Messages Are Incomplete • No Dial Tone • RING SELECT 1 2 3 • PULL TABS TO OPEN • PULL TABS TO OPEN PULL TABS TO OPEN Make sure all plugs are connected properly.
T E L E P H O N E O P E R A T I O N Dial Mode Mute This phone comes set to operate with touch tone service. If you have dial pulse (rotary) service, you will need to reset the dial mode. If you hear clicks (not tones) when you dial, you have dial pulse (rotary) service. Mute lets you hear the other party, but prevents the other party from hearing you. To change to dial pulse mode: 1 Press and release G. 2 Press #, #, #, 3. T E L E P H O N E When light goes on, battery needs to be replaced.
