958_book_1ATT 6/3 6/3/02 4:27 PM Page i USER’S MANUAL Part 2 Telephone with Caller ID 958 DRAFT 6/3/02 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones.
958_book_1ATT 6/3 6/3/02 4:27 PM Page ii Visit us at www.telephones.att.com © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones. Printed in China.
958_book_1ATT 6/3 6/3/02 4:27 PM Page iv CONTENTS BEFORE YOU BEGIN . . . . . . . . . 1 TELEPHONE DIRECTORY . . . . 13 About Caller Identification (Caller ID) . . . . . . . . . . . . . . . 1 About Call History . . . . . . . . . . . 1 About Home Area Code and Local Area Codes . . . . . . . . . . 1 Storing Directory Numbers & Names . . . . . . . . . . . . . . . 13 Storing a Pause or Flash in a Directory Number . . . . . . . . 14 Storing Call History Numbers in Directory . . . . . . . . . . . . .
958_book_1ATT 6/3 6/3/02 4:27 PM Page 1 BEFORE YOU BEGIN About Caller Identification (Caller ID) This product has a Caller ID with Call Waiting feature that works with service from your local phone service provider. Caller ID with Call Waiting lets you see who’s calling before you answer the phone, even when you’re on another call. You may need to change your phone service to use this feature.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 2 INSTALLATION Table/Desk Installation 1 (Optional) You can adjust how much the phone tilts by flipping out the “feet” underneath the phone. Place your thumbs as shown in figure a and flip the feet over. They will look like figure b. figure a 2 figure b Connect the line cord to the telephone.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 3 INSTALLATION 4 5 6 Connect the line cord to a modular jack. Connect the power cord to a standard electrical outlet not controlled by a wall switch. NOTE: When you first plug in the power cord, the screen displays WHICH LANGUAGE?. Follow the programming steps on page 6 after installation is complete. Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 4 INSTALLATION Wall Installation 1 Reposition the base wedge for wall use. Make sure the pull-out feet are not extended. Press on the base wedge as shown in figure a to remove the wedge. Turn the wedge so that the larger end is toward the bottom of the telephone. Reattach the wedge by positioning it as shown in figure c and pressing in the direction of the arrows until it locks in place. figure a 2 4 figure b figure c Connect the line cord to the telephone.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 5 INSTALLATION 4 Reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook, and slide the tab up and out of its slot. Turn the tab so that the end with the “hook” is up. Then insert the tab back into its slot. Switchhook Handset tab 5 Plug the power cord into the jack labeled POWER. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111.
58_book_1ATT 6/3 6/3/02 4:27 PM Page 6 FEATURE SETTINGS NOTE: You can exit feature setup at any time by pressing C or by lifting the handset when there is no incoming call. The order features appear in the menu changes after initial setup. For complete feature setup, see pages 8 and 9. Language Selection You can select ENGLISH, ESPANOL (Spanish) or FRANCAIS (French) as the language in which your Caller ID information is displayed.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 7 FEATURE SETTINGS Set Home Area Code You must program your area code, so your phone can properly recognize and dial calls. If for calls within You dial Enter in Step 2 your area code 7 digits (phone number, no area code) Your home area code 10 digits (area code + phone number) — OR — 11 digits (1 + area code + phone number) 000 1 Press N until the screen displays: HAC-___ HOME AREA CODE? 2 Use the keypad to enter the three digits of your home area code.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 8 FEATURE SETTINGS Set Remaining Features You can customize how the features of this product work. 1 Press and release N until the screen displays the feature you want to set. 2 Press CALL LIST + or CALL LIST - until the screen displays your selected setting. Refer to the “Feature Summary”for a full description of the features and your choices. 3 Press N. This saves your selection and automatically moves you to the next option.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 9 FEATURE SETTINGS Feature/Options: Choice: VMW LOCK Check with your phone service provider for more information about signal requirements. System turns off Stutter Detect for message NO * waiting. YES CALL HISTORY ALL CALLS * NO CALLS UNANS. CALLS REPEATED CALLS System receives both Stutter Detect and FSK signals. Choose which incoming calls are displayed. The screen displays all calls received. The screen displays no call history.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 10 TELEPHONE OPERATION Redial Lift the handset or press K, then press R to call the last number dialed (up to 32 digits). Flash/Call Waiting Press to connect to the new call when you receive a call waiting signal. Press again to return to original call. Also use to access other phone company subscriber services. Hold Press to put a call on hold. To return to the call, press H again, press K, or lift the handset.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 11 TELEPHONE OPERATION Ringer Volume Adjust RINGER volume (LO or HI) or turn RINGER OFF. Flashes when a call is coming in, on steadily when a line is in use. Press to dial number displayed on screen (see CALLER ID OPERATION). MUTE Press to prevent the other party from hearing you (you will still be able to hear the other party). Press again to return to two-way conversation. Adjust Handset or Speaker Volume Press to adjust volume.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 12 TELEPHONE OPERATION Screen Icons Screen Displays: When: Indicates you have unreviewed voice mail. Indicates a transmission error from phone company. Flashes when line is ringing. Remains steady when this phone or another phone on the same line is in use.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 13 TELEPHONE DIRECTORY This telephone can store up to 50 telephone numbers (with names) that you can dial just by pressing d, selecting a directory entry using CALL LIST - or +, and then pressing D. When entering a number or name, you can use CALL LIST - to backspace. Press C at any time to exit directory without saving changes and return to the idle screen. Storing Directory Numbers & Names 1 Press d, then O.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 14 TELEPHONE DIRECTORY NOTE: Entries cannot be edited after screen displays STORED. Storing a Pause or Flash in a Directory Number Press + twice to store a pause in the dialing sequence (the screen displays P). Press F to store a press of the flash button (the screen displays F). Storing Call History Numbers in Directory 1 2 Press CALL LIST + or CALL LIST - to scroll through the call history. Press d to store displayed call information in the telephone directory.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 15 CALLER ID OPERATION Time call was received Date call was received Indicates unreviewed call information Caller’s telephone number Indicates repeat call Position of call in call history Caller’s name Setting Display Screen Options You can customize how the Caller ID features of this product work. See “Set Remaining Features” on page 10 for instructions.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 16 CALLER ID OPERATION Message Waiting and NEW CALL Light This light stays on when you have received call information but have not yet reviewed it. If you subscribe to a voice mail service, this light flashes when you have unretrieved messages waiting. Removing Call Records Removing a Specific Call Record 1 Press CALL LIST + or CALL LIST - to display the call record you want to remove. 2 Press and release r. The system beeps and the call record is removed.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 17 CALLER ID OPERATION Call Display Between the first and second rings, the screen displays: • Your caller’s name (15 letters are sent by your phone company), • The caller’s area code and telephone number (area code is not displayed if it is programmed as the Home Area Code), • The time and date of the call, and • The call’s position in call history. Call information is displayed for about 30 seconds.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 18 IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 800 222–3111. Please retain your receipt as your proof of purchase. No Dial Tone • • Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends.
958_book_1ATT 6/3 6/3/02 4:27 PM Page 19 IN CASE OF DIFFICULTY Message Waiting/New Call Light Stays On • • Make sure you have reviewed all calls. Unplug the power cord for 10 seconds, then plug it back in. Message Waiting/NEW CALL Light Flashes • • Make sure you have reviewed all telephone company voice mail. Reset the voice mail waiting indicator.
