REVISED 1/18/99 1 User’s Manual for Tapeless Digital Answering System with Time/Day AS45 Fold open this manual for information about this product’s installation and operation. Please read Part 1 – Important Product Information, included in this package. Part 2 © 1999 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico.
INSTALLATION TEL LINE TEL SET Strain Relief Tab Telephone Set Cord Modular Telephone Jack Standard Electrical Outlet Power Cord 1 Connect the telephone line cord. Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system. Plug the other end into a modular telephone jack. 2 Connect the telephone. Telephone Line Cord 3 NOTE: If you do not want to connect a telephone, skip to Step 3. Connect the power cord.
OPERATION Displays number of messages and other information Adjust volume Set and hear time/day Delete all or selected messages Use with other buttons to change/hear settings Turn system on or off Record and play outgoing announcement / Skip all or part of a message Microphone Play/Stop messages Record a memo / Repeat all or part of a message PLAY Light indicates messages Setting the Clock Recording Your Announcement You’ll need to set the clock so that it can announce the day and time that each me
OPERATION Press P to exit — OR — The system will time out after 30 seconds and save any changes already made. Answering Calls When the system answers a call, the caller hears the announcement you recorded, followed by a beep. After the beep, the system begins recording your caller’s message. A caller can leave a message up to three minutes long.
OPERATION Announcement Monitor Saving Messages You can choose whether to hear the announcement when your system answers a call, or have it silent (off) on your end (your caller will still hear an announcement). 1 Press and hold S. After the Ring Select setting is announced, continue to press and release S until the system announces “Monitor is on (or off)”. or 2 Press and release until the system announces your selection. 3 Press and release P or S to exit.
REMOTE OPERATION Connect with the Answering System Deleting Messages 1 After you have listened to all messages and heard the two beeps, press 3 3. 2 3 Delete All Messages Dial your telephone number from a touch tone phone with a different telephone number. When the system answers, enter your three-digit Access Code during or after the announcement. The system announces the number of messages, then beeps twice.
REMOTE OPERATION Turn System Off Memory Full Press 0 0. The system answers after 10 rings, then announces “Memory is full,” and beeps twice, you must delete messages to make room for new ones. 1 Enter the Remote Access Code after two-beep signal. 2 Listen to messages, and delete some or all of them. 3 Press 0 to make sure your system is on before you hang up. Turn System On When the system is off, it answers after 10 rings, announces “The machine is off,” and beeps twice.
I N C A S E O F D I F F I C U LT Y System Does Not Respond To Remote Commands If this answering system does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 722–9125. • Message Window Is Blank • • Make sure the power cord is securely connected to both the answering system and an electrical outlet not controlled by a wall switch. Press O to make sure the system is on.
© 1999 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico. 848317749 Issue 1AT&T © 1999 Lucent Technologies Consumer Products L.P. All rights reserved. Printed in Mexico.
ONE KEY REMOTE COMMANDS ONE KEY REMOTE COMMANDS Play All Play New Delete Play All Play New Delete Repeat Stop/Exit Skip Repeat Stop/Exit Skip System On Record Memo Annc. Annc.
INSTALLATION REVISED 1/18/99 TEL LINE OPERATION OPERATION Displays number of messages and other information Strain Relief Tab Adjust volume Telephone Set Cord Modular Telephone Jack Standard Electrical Outlet Set and hear time/day Delete all or selected messages Use with other buttons to change/hear settings Turn system on or off Power Cord Record and play outgoing announcement / Skip all or part of a message Telephone Line Cord Microphone 1 2 1 Connect the telephone line cord.
OPERATION REMOTE OPERATION Announcement Monitor Saving Messages You can choose whether to hear the announcement when your system answers a call, or have it silent (off) on your end (your caller will still hear an announcement). 1 Press and hold S. After the Ring Select setting is announced, continue to press and release S until the system announces “Monitor is on (or off)”. 2 Press and release or until the system announces your selection. 3 Press and release P or S to exit.