USER’S MANUAL Part 2 2.4 GHz Expansion Handset 2300 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones.
Visit us at www.telephones.att.com © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones. Printed in China.
BEFORE YOU BEGIN . . . . . . 1 Parts List . . . . . . . . . . . . . . . 1 Compatiblity . . . . . . . . . . . . . 2 About Handset Registration . . 2 INSTALLATION . . . . . . . . . . 3 Charging Stand Installation . . . 3 Belt Clip . . . . . . . . . . . . . . . . 5 Headset . . . . . . . . . . . . . . . . 5 FEATURE SETUP AND OPERATION . . . . . . . 6 DEFAULT SETTINGS . . . . . . . 7 TECHNICAL SPECIFICATIONS . . . . . . .
BEFORE YOU BEGIN BEFORE YOU BEGIN Parts List Your box should include: USER’S MANUAL Part 2 This User’s Manual Handset 2.4 GHz Expansion Handset 2300 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones. All rights reserved. AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones.
BEFORE YOU BEGIN Compatibility This AT&T 2300 expansion handset is compatible with the AT&T 2320, 2325, 2355 and 2365 telephones. You may add up to three expansion handsets to your compatible telephone, for a total of four handsets. If you try to install a fifth handset, registration will be blocked. About Handset Registration Each expansion handset must be individually registered with your AT&T 2320, 2325, 2355 or 2365 base.
INSTALLATION Charging Stand Installation INSTALLATION Install the charging stand away from electronic NOTE: equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. 1 Connect the power cord to an electrical outlet not controlled by a wall switch.
INSTALLATION 2 Install the handset battery. Use only AT&T Battery 3301, SKU# 91076. a) Remove battery compartment cover by pressing on indentation and sliding downward. b) Plug the battery pack connector into handset. Place the battery pack and wires in the compartment. c) Replace cover by sliding it on its track up over battery case until it snaps firmly into place. 3 4 5 4 Charge the handset battery. • Place the handset in the charging stand. • Charge the battery at least 12 hours.
Belt Clip a) Pull clip away from handset to remove. Headset b) Press tabs on belt clip into slots on back of handset to reattach. INSTALLATION You can remove the belt clip from the handset. You can use this telephone hands-free when you install any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Plug the headset into the jack located on the right side of the handset (under the small rubber flap).
FEATURE SETUP AND OPERATION FEATURE SETUP AND OPERATION FOR INSTRUCTIONS TO SETUP AND OPERATE THIS EXPANSION HANDSET, REFER TO THE MANUAL THAT CAME WITH YOUR ORIGINAL BASE TELEPHONE.
DEFAULT SETTING FUNCTION: DEFAULT SETTING: Dial Method Tone Handset Volume 2 Ring Volume 6 External Ring Pattern 0 Internal Ring Pattern 1 Key Click ON DEFAULT SETTINGS DEFAULT SETTINGS 7
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Frequency Range 2400 MHz – 2483 MHz Channels 95 Channel Spacing 864 kHz Output Power 23 dBm Sensitivity -92 dBm Modulation GFSK Operating Temperature 0°C – 40°C 8 Base Unit Voltage 96 – 144 Vrms (AC Voltage, 60Hz) Base Unit Voltage 9 Vdc (AC Adapter Output) Handset Voltage 3.6– 4.