Quick start guide TR1909 Trimline® telephone with caller ID/call waiting For customer service or product information, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
Handset layout CALL LIST IN USE light / When the telephone is in idle mode, press to display caller ID information. Flashes quickly when there is an incoming call. Flashes slowly when the telephone line cord is not plugged into a wall jack or another telephone on the same line is in use. CLEAR Press to exit dialing, to exit storing a number in memory, to exit the call log, or to return to the idle screen anytime without saving the changes. OPTION Press to display the setting options.
Handset layout M1, M2, M3 Switch hook Press to dial a onetouch number from the memory. When held, the telephone is in idle mode. When released, the telephone is ready to make a call. Listening volume Slide to adjust the handset listening volume to LO, MED, or HI. PAUSE/REDIAL When the handset is lifted, press to redial the last number dialed. When storing a number in the memory, press to insert a three-second dialing pause. MEMORY Press to access telephone numbers stored in the memory.
Screen display messages Screen icons CALL# Call number in the call log. NEW New (unreviewed) call. REP Repeat call from the same number. • The telephone line cord is not plugged into the wall jack. • The telephone or another telephone on the same line is in use. LOW The battery power is low. Screen display messages REMOVE ALL? Remove all call log entries. -END OF LIST- You have reached the end of the call log entries. Pro Program a one-touch or twotouch memory.
Battery installation Before using the telephone, you should install four good AA alkaline batteries (not included) to provide memory backup and enable the use of some features. The four AA batteries are required for caller ID features and the IN USE light to work. If good batteries are not installed, the display only works when you lift the handset.
Battery installation 2. Install four new AA batteries (not included) in the battery compartment according to the labels + and - engraved in the compartment. 3. Close the battery compartment cover. Make sure it clicks into place. NOTES: • Do not mix old and new batteries and do not mix alkaline and standard (carbon-zinc) batteries. • When the batteries are installed, the screen will show 12:00 and the clock will begin to run. It will reset to the correct time when the first caller ID data is received.
Telephone installation If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone lines, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. Install the telephone as shown below. 1.
Installation options Your telephone base is ready for tabletop use. If you want to mount your telephone on a wall, use the provided wall-mount bracket to connect with a standard dual-stud telephone wallmounting plate. If you do not have this mounting plate, you can purchase one from many hardware or consumer electronic retailers. You might need a professional to install the mounting plate.
Installation options 2. Remove the bracket from the base. Hold the telephone base with both hands and then slide the bracket upwards as the arrows indicate. 3. Rotate the bracket to the wall installation position. Push the bracket upwards as shown below until it clicks into place. 4. Route the telephone line cord through the slot as shown below and plug the other end of the telephone line cord into a telephone wall jack.
Installation options 5. Place the handset back on the telephone base. Tabletop installation To return the bracket from the wall installation to tabletop use, follow the instructions below. 1. Remove the telephone base from the wall mounting plate. Unplug the telephone line cord from the telephone wall jack and remove the cord from the slots under the telephone base. 2. Lift the handset and place it aside. On the telephone base, pull out the handset tab and rotate it 180 degrees.
Installation options 3. Remove the bracket from the base. Hold the telephone base firmly and then slide the bracket downwards as the arrows indicate. 5. Route the telephone line cord through the slot as shown below. Plug the other end of the telephone line cord into the telephone wall jack. DSL filter (not included) 10 4. Rotate the bracket to the tabletop installation position. Push the bracket down as shown below until it clicks into place. 6. Place the handset back on the telephone base.
www.telephones.att.com Trimline® is a registered trademark of Advanced American Telephones. © 2009 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China.
