INSTRUCTIONS FOR USE GB HG3011A 1
Congratulations from ATAG Dear Customer, Congratulations with your new Hob. It is important that you become familiar with the functions and features of the Hob. You should therefore read these operating instructions as they will help you get the most out of your new Hob. Pay extra attention to sections marked . These are warning texts to help you avoid accidents. Keep the operating instructions.
Table of contents Contents Page no For the user Your new aplliance ....................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 6 Operations .................................................................................................... 7 Burner ring/cover ........
Safety information Never leave the hob unattended while deep fat frying, or heating fats and oils. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. The appliance is not intended for use by young children or infirm persons without supervision.
Description of the product Burner Control knob 5
Operations Burner markings Symbols at each control knob indicates which burner is adjusted with the control knob. Front Burner Back burner Panel markings Each control knob has a ring showing the scale of markings. Off.
Hulpgasring / branderdeksel In de door de branderkelk samen met de branderdeksel en hulpgasring gevormde ruimte vindt de vermenging van gas en lucht plaats, waardoor het gas op juiste wijze brandt. NB.: Het is daarom zeer belangrijk dat elk branderdeksel c.q. elke hulpgasring correct op de brander worden aangebracht. Als de hulpgasring of het branderdeksel verkeerd is aangebracht, dan werkt de brander niet goed, en kunnen de branders binnen korte tijd beschadigd raken.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Maintenance and cleaning Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish. To ensure that the steel retains its shine, it is recommended that you use a polishing agent for stainless steel on a regular basis. Always polish in the direction of the steel finish (crosswise). Never use steel wool, metal sponges or other abrasive cleaning agents.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top. Tighten the brackets on to the table top with an ordinary screwdriver.
It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges.
Do not install the hob above drawers.
It is not necessary to attach the reinforcement beam to the work top surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges.
Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary. Pressure test The unit should be pressure-tested at Max. 150 mbar.
Technical data Type of gas Adjusted to natural gas: G20 - 20 mbar G25 - 25mbar Cable type 0,75 mm² HO5 V2V2-F 240 V 1N + PE N L1 Category and pressures BE: II2E+3+ 20/25 - 28/37 mbar The Dropinett must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) NL: II2L3B/P 25 - 30 mbar Max.
Service If the hob is not working correctly, please carry out the following checks before contacting your local ATAG Service Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
Guarantee Please refer to the accompanying guarantee booklet and guarantee card for guarantee conditions.
Important Advice This appliance has been constructed to ensure safety. However, repairs performed by non-specialists could impair the safety of the appliance. To ensure safety and prevent any damage, it is recommended to only allow people with the appropriate professional skill to repair this appliance. We recommend that your have this appliance repaired and/or checked only by a your local professional serviceman or by ATAG Service and use only original ATAG parts.
325 88-9162 Rev. 1-320 Postbus 1033. 6920 BA Duiven.
