Operation Manual

19
GB
* Depending on model and options
W Remove the shelves as shown in the
illustration:
- Lift the glass shelf*, align the recess over
the support, tilt to the side and remove
towards you at an angle.
- Always insert shelves with the raised
edge or guard bar at the back pointing
upwards, otherwise food may freeze
onto the rear wall.
W Always remove the top door rack (butter
and cheese compartment) together with
the ap*. Then press one of the side
walls carefully to the outside to release
the ap pin. The ap can then be lifted
out.
- The shelves and door racks can be
dismantled for cleaning. Remove the
trims and sides from the glass shelves.
- Remove the protective lm from the
decorative trims.
W Clean the drain hole on the rear wall above the vegetable
bins frequently,
arrow in illustration. If
necessary, clean with a thin object,
e.g. a cotton swab or similar.
W
Then connect/switch on the appliance and
insert the food to be frozen.
If the appliance is to be
leftswitchedoforanylengthof
time
empty the appliance, disconnect from the mains, clean as
described above and leave the door open so as to avoid odours.
Troubleshooting
Your appliance is designed and manufactured for a long life span
and reliable operation.
If a malfunction nonetheless occurs during operation, check
whether it is due to an operating error. Please note that even
during the warranty period the resultant servicing costs in this
case will have to be borne by the owner.
You may be able to rectify the following faults by checking the
possible causes yourself:
Malfunction - Possible cause and remedy
______________________________________________
Appliancedoesnotwork,displayiso
- Is the appliance switched on properly?
- Is the mains plug properly inserted in the socket?
- Is the socket fuse intact?
The interior light does not come on
- Is the appliance switched on?
- Has the door been open for more than 15 minutes? The interior
light switches o automatically after the door has been opened
for approx. 15 minutes.
- If it does not switch on when the door is opened briey, but the
temperature display is working, it may be defective.
Mains Voltage
Important! To prevent injury or damage, always ask our
customer service department to carry out any repairs and
replace the LED interior light.
Caution - class 1M laser radiation. When cover
is removed, do not look directly at light through
optical instruments.
Loud running noise
- Is the appliance standing rmly on the oor, or does the com-
pressor cause nearby items of furniture or objects to vibrate?
If necessary, move bottles and containers apart.
-
Burbling noises are normal. These are caused by the refriger-
ant owing round the refrigerant circuit.
A short
clicking sound: This will be heard whenever the
refrigeration unit (the motor) switches on or o automatically.
Motor noise: This will be slightly louder for a brief period when
the refrigeration unit switches on.
The temperature is not cold enough
- Is the temperature setting correct? If necessary, set a lower
temperature and check the display after 24 hours.
- Does the door close properly?
- Is the appliance built in properly?
- Is the appliance suciently well ventilated?
Clear ventilation grilles if necessary.
- Is the ambient temperature too hot? (See "Safety regula-
tions")
- Has the appliance been opened too often or left open too
long?
- If applicable, wait until the appliance reaches the required
temperature itself.
Customer service and type plate
If none of the above causes apply and you cannot rectify
the fault yourself, or if the temperature display reads
"
F 0" to "F 5", this means that there is a fault. Please contact
your nearest customer service department (see enclosed list for
addresses), indicating the
fault number displayed, together
with the
type designation 1,
service number 2 and
serial number 3
as given on the type plate. This
will help us to provide you with a
faster and more accurate service.
The type plate is located inside the
appliance on the left-hand side.
Leave the appliance shut until the
customer service engineer arrives
so as to prevent any further cold loss.