User manual Dishwasher VA5511AT
Contents Safety information ................................... 2 Product description ................................ 3 Control panel .......................................... 4 First use ................................................. 5 Set the water softener ............................ 5 Use of dishwasher salt ............................ 6 Use of rinse aid ....................................... 7 Daily use ................................................. 8 Load cutlery and dishes ..............
Installation • Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. • All packaging must be removed before use. • Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. • For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way.
Control panel 7 1 2 3 4 5 6 7 On/Off button Digital display Delay start button Programme selection buttons Multitab button (MULTITABLET) Indicator lights Function buttons Indicator lights Salt Comes on when the special salt has run out. Rinse aid Comes on when the rinse aid has run out.
programme is still set. In this case, to return to setting mode, the programme has to be cancelled. To cancel a set programme or a programme in progress Simultaneously press and hold the two function buttons B and C until all the programme button lights come on. The programme has been cancelled and the machine is now in setting mode.
Water hardness Adjusting the water hardness setting Use of salt 19 - 22 33 - 39 3,3 - 3,9 level 5 yes 15 - 18 26 - 32 2,6 - 3,2 level 4 yes 11 - 14 19 - 25 1,9 - 2,5 level 3 yes 4 - 10 7 - 18 0,7 - 1,8 level 2 yes <4 <7 < 0,7 level 1 no Setting electronically The dishwasher is factory set at level 5. 1. Press the On/Off button. The dishwasher must be in setting mode. 2.
The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salt that takes longer to dissolve then this can take longer. The operation of the machine is not affected. Use of rinse aid Warning! Only use branded rinse aid for dishwashers. Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.
Daily use • Check if it’s necessary to refill with dishwasher salt or rinse aid. • Load cutlery and dishes into the dishwasher. • Fill with dishwasher detergent. • Select a wash programme suitable for the cutlery and dishes. • Start the wash programme. Helpful hints and tips Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. • Before loading the dishes, you should: – Remove all left over food and debris.
Load cutlery and dishes The lower basket The lower basket is designed to take saucepan, lids, plates, salad bowls, cutlery etc. A service dish can be placed in front of the cutlery basket. It is possible to adjust the width of the left row of prongs. 1. Take the right-hand row of prongs at the back. 2. Pull it upwards until it disengages. 3. Push it backwards out of the guide. 4. Insert the prong in the other guide. 5. Press it down until it engages into place.
Mix spoons with other cutlery to prevent them from sticking together. To make loading of the cutlery basket easier, lower the cutlery basket handle. To reassemble, reverse the procedure. For best results we recommend that you use the cutlery grids. If the size and dimensions of the cutlery do not allow the use of the grids, they can be easily hidden. The cutlery basket is in two parts which can be separated to give greater loading flexibility.
1. Pull out the basket until it stops. 2. Lift up the upper basket as far as it will go and then lower it vertically. It will latch into the lower or higher position. Glass holder • For glasses with long stems and tall cylindrical glasses, fold up the glass holder. (Picture 1). • To unload or when it is not needed, fold the glass holder back to the right. (Picture 2). Warning! An open door can be a hazard. Close the door after loading your appliance.
Maximum plate sizes with upper basket in lower position. Arrangement of large plates in the lower basket. 20 30 25 Use of detergent Only use detergents specifically designed for use in dishwashers. Please observe the manufacturer’s dosing and storage recommendations as stated on the detergent packaging. Using no more than the correct amount of detergent contributes to reducing pollution. 1 2 Fill with detergent 1. Open the lid. 3.
4. Close the lid and press until it locks in place. Detergent tablets from different manufacturers dissolve at different rates. For this reason, some detergent tablets do not attain their full cleaning power during short washing programmes. Therefore, please use long washing programmes when using detergent tablets, to ensure the complete removal of detergent residuals.
4. To change the setting, press button B again, the digital display indicates the new setting. 5. To memorize the operation, switch off the dishwasher by pressing the On/Off button. If you decide to revert back to the use of individual detergents we advise that you: 1. Deactivate the Multitab function. 2. Fill up the salt container and the rinse aid dispenser again. 3. Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes. 4.
way they will be cooler and the drying will be improved. Unloading the dishwasher steel will eventually become cooler than the dishes. • Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance. • Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one.
The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes. Care and cleaning Cleaning the filters The filters must be checked and cleaned. Dirty filters will degrade the washing result. Warning! Before cleaning the filters ensure that the machine is switched off. NEVER use the dishwasher without filters.
Caution! Do not damage nozzle openings. Be careful when cleaning the spray arms. Ceiling spray arm 1. Turn the fixing screw (A) anticlockwise. 2. Pull the spray arm off the shaft. 3. Clean the spray arm nozzles and the fixing screw. 4. Fasten the spray arm with the fixing screw (A) by turning it clockwise. Upper basket spray arm 1. To remove the upper basket spray arm, turn it laterally. 2. Clean the spray arms nozzles. 3. Replace the spray arm, press upwards until it snaps into place.
Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc...): 1. Unplug it. 2. Turn the water tap off. 3. Remove the water inlet and discharge hoses. 4. Pull the machine out together with the hoses. Avoid over tilting the machine during transportation.
Malfunction Possible cause and solution • The dishwasher door has not been properly closed. Close the door. • The main plug is not plugged in. Insert the main plug • The fuse has blown out in the household fuse box. Replace the fuse. • Delay start has been set. If dishes are to be washed immediately, cancel the delay start. The programme does not start Once these checks have been carried out switch on the appliance and close the door.
Electrical connection - Voltage Overall power - Fuse Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door. Water supply pressure Minimum Maximum 0,05 MPa (0,5 bar) 0,8 MPa (8 bar) Capacity 11 place settings Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values").
3 3 3 6 3 1 8 1 3 3 1 1 3 1 1 3 1 3 1 3 1 1 3 1 1 1 5 5 5 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 7 7 Arrangement cutlery basket Arrangement cutlery basket Installation Warning! Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Remove all packaging before positioning the machine.
The plinth area that can still be seen after the hinged door has been installed. It can be hidden with a matching panel or by extending the panel of the kitchen unit that is under the appliance. To fit the hinged door 1. Fit the two lateral bars A as shown in the figure. 4. Align the machine laterally in the plinth area with the angle AN. Tighten the screw V slightly. 5. Before the installation of the hinge support, screw bottom unit of the hinge into the holes provided in the hinge support. 6.
10. Snap the hinges into the bottom units of the hinges. Hold the hinged door carefully, so that the hinges are not bent. 8. Mark out and drill 8 holes b for the two guides (ø 2 mm, 12 mm deep) at the top of the hinged door. To do this, align the drilling template with the top edge of the hinged door. 9. Screw the hinges using 4 countersunkhead wood screws. Screw the guides to the hinged door using 8 Spax screws (4 x 20 pozidrive). 11.
14. To adjust the depth of the appliance. Open the appliance door carefully, take care not to change the found position. Fix the appliance laterally at the top using wood screws. 15. Tighten screw V to fix laterally the appliance . There are 2 oblong holes at the right and at the left in the hinge support to allow access for the screwdriver. Water connection Water inlet connection This dishwasher may be fed with either hot (max. 60°) or cold water. Nevertheless we advise you use a cold water supply.
Warning! Dangerous voltage Water drain connection The water drain hose can face either to the right or left of the dishwasher Ensure that the hose is not bent or squashed as this could prevent or slow down the discharge of water. The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine. The highest point of the drain hose must not be more than 500 mm from the base of the appliance.
Electrical connection Warning! Safety standards require the appliance to be earthed. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs, connectors and extension cables must not be used.
Nederland Home Product Service (ATAG) Postbus 249 6920 AE DUIVEN tel: 0900 - 5550001 fax: 026 - 8821444 België ATAG België NV 9420 Erpe-Mere tel: 053 - 806208 fax: 053 - 806057 Postbus 1033 • 6920 BA Duiven • Nederland 117970260 - 00 - 022008