ATD‐10525 12V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual
KNOW YOUR PRODUCT (DRILL) 1. Keyless chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery 6. Battery release buttons 7. Variable speed switch 8. LED light 9. Quick Battery Charger Drill Specifications: Motor: 12V Charge time: 90 minutes No load speed: 0 – 350/min, 0 – 1150/min Chuck: 10mm Keyless Torque: 11 ft. lbs. Battery: 1.3Ah Lithium Ion Weight with 1 battery: 1.
KNOW YOUR PRODUCT (DRIVER) 1. Quick Release chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery 6. Battery release buttons 7. Variable speed switch 8. LED light 9. Quick Battery Charger Driver Specifications: Motor: 12V Charge time: 90 minutes No load speed: 0 – 350/min, 0 – 1150/min Chuck: Quick Release Chuck Torque: 11 ft. lbs. Battery: 1.
THIS SECTION CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY CHARGER. Danger! If the battery pack case is cracked or damaged, do not insert into charger. There is a danger of electric shock or electrocution. Warning! Do not allow any liquid to get inside charger. Electric shock may result. To facilitate cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an un‐insulated trailer.
Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in all of the warnings refers to your mains‐operated (corded) power tool or battery‐operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Over Current Protection Should the battery be overloaded and the maximum current draw be exceeded the battery will temporarily stop working to protect the internal components. The battery will resume to normal operation once the excessive current draw has returned to normal safe level. This may take a few seconds. Short Circuit Protection If the battery pack was to short circuit the short circuit protector would immediately stop the battery pack from operating.
Thermal voltage protection indication In the event that the thermal or voltage protection circuit has been activated the battery will cease to operate. This can happen when the tool has been used for extended periods or worked hard with large drill bits or accessories. If you place the battery on the charger the LED lights will give you the appearance that the battery is fully charged. Leave the battery on the charger to charge for 90 minutes.
Changing the Direction of Rotation The direction of rotation can be changed with the forward/reverse selector (4). This is located above the variable speed switch (7) (see Fig. 4). To select the forward drilling position, push the forward/reverse selector (4) hard left. To select the reverse drilling position, push the forward/reverse selector (4) hard right. The variable speed switch (7) can be locked off by pushing the forward/reverse selector (4) into the middle of both the forward and reverse positions.
Installing Drill or Driver Bits • Remove the battery (5) from the drill. • Open or close the keyless chuck (1) to a point where the opening is slightly larger than the drill or driver bit you intend to use. • Insert the drill or driver bit into the keyless chuck (1), ensuring the end of the drill or driver bit does not touch the screw inside the keyless chuck (1). • Tighten the keyless chuck (1) onto drill or driver bit as above (See Fig. 8).
• • • • When not in use, the drill should be stored in a dry, frost free location, out of reach of children. Keep ventilation slots of the drill clean at all times and prevent any foreign matter from entering. If the housing of the drill requires cleaning, do not use solvents but a moist soft cloth only. Blow out the ventilation slots with compressed air periodically.
WARRANTY 1 YEAR REPLACEMENT WARRANTY THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES The warranty is only made available by returning the product to the point of sale. PURCHASED FROM:________________________________________________ DATE PURCHASED: ________________________________________________ INVOICE/RECIEPT NUMBER:_________________________________________ Your ATD10525 is warranted for a period of 12 months from the original date of purchase.
