Specifications



ChangingtheDirectionofRotation
Thedirectionofrotationcanbechangedwiththeforward/reverseselector(4).
Thisislocatedabovethevariablespeedswitch(7)(seeFig.4).Toselectthe
forwarddrillingposition,pushtheforward/reverseselector(4)hardleft.To
selectthereversedrillingposition,pushthe
forward/reverseselector(4)hard
right.Thevariablespeedswitch(7)canbelockedoffbypushingthe
forward/reverseselector(4)intothemiddleofboththeforwardandreverse
positions.Donotchangethedirectionofrotationwhilethekeylesschuck(1)is
inmotion.

SpeedControl
Thedrill
hasa2speedgearbox.Thespeedselector(3)islocatedonthetopof
thedrill(seeFig.5).Firstgearhasarangeof0‐350/min.Secondgearhasa
rangeof0‐1150/min.

TorqueSettings(Tighteningpowerofyourdrill)
Whenusingyourdrillforvariousdriving
applications,itbecomesnecessaryto
increaseanddecreasethepowerandtorqueinordertopreventthepossibility
ofdamagingscrewheads,threads,workpieces,etc.Ingeneral,powerand
torqueshouldcorrespondtothedifficultyofthescrewtobedriven.Iftorqueistoohigh,thescrewscan
be
damagedorbroken.

ToAdjustTorque
• Locatethearrowonthefrontofthedrillhousing(seeFig. 6).
• Identifythetorquesettingsand1drillsettingonthetorqueadjustment
collar(2).
• Rotatethetorqueadjustmentcollar (2)tothedesiredsetting,aligning
therequired
numberonthetorqueadjustmentcollar(2)withthe
arrowonthedrillhousing.
• Toincreaseordecreasetorque,rotatethetorqueadjustmentcollar(2).

Thelowerthenumber,thelowerthetorquesetting.Thehigherthenumber,thehigherthetorquesetting.Always
checkthatthecorrecttorque
isselectedbypracticingonscrapmaterialpriortocarryingoutajob.Thetorque
settingrequiredtodrivescrewswilldifferwith differentmaterials.Startwiththetorquesettingonthenumber
youthinkisappropriate(Eg:4)andsimplyincreasethetorqueadjustmentcollartoahighernumber
ifthescrew
headisnotsittingflushwithyourworkpiece.Removethescrewafteradjustingandre‐drivethescrewbackinto
theworkpieceuntilthecorrecttorqueadjustmentleavesthescrewheadflushwithyourworkpiece.

KeylessChuck
Akeylesschuck(1)isincludedonyourdrilltoallow
foreasyinstallationandremoval
ofbits/accessories.Toopenandclosethekeylesschuck(1),rotatethechuckbody
withyourotherhand(seeFig.7).Thearrowsonthechuckindicateinwhichdirection
torotatethechuckbodyinordertoGRIP(tighten)orRELEASE(unlock)thedrill
bit.
Warning!Donotholdthechuckbodywithonehandandusepowerofthedrillto
tightenorloosenthechuckjaws.Thechuckbodycouldslipandyourhandcould
comeincontactwitharotatingaccessory.Thiscouldcauseanaccidentresultingin
personalinjury.
