User's Manual

FEATURES
♦ Limits torque applied with reduced-friction release mechanism.
♦ Can be used with confidence in all automotive, aircraft, marine
and industrial applications.
♦ Lock ring prevents accidental change of torque setting.
♦ Pliable handgrip of soft Thermoplastic rubber protects painted
surfaces and simplifies use with greasy hands. Resistant to
mechanical damage and impervious to automotive fluids such
as gasoline, oil, kerosene, etc.
♦ Ratchet action requires only 10 degrees handle travel.
♦ Extra str
ength ratchet design for long life.
♦ May be used continually at maximum torque capacity.
♦ Wrench cannot be damaged by normal handling or dropping
from workbench.
♦ Mechanism protected from routine contamination.
♦ Finished with tough, durable chromium-nickel plating.
♦ All parts corrosion proofed.
♦ Wrench made of highest quality CR-MOLY steel.
SUGGESTIONS
Proper use of this professional torque wrench will give you
complete satisfaction in its performance and reliability. Following
are some helpful tips:
1. Greater torque accuracy is assured by gripping it properly.
Grasp the GRIP, not the SHAFT, and pull smoothly.
2. Each torque wrench is lubricated before leaving the factory. If it
has not been used for some time, it should be operated several
times to re-distribute the lubricant within the working
mechanism.
3. Never attempt to turn the GRIP when the LOCK RING is in the
"LOCK" position.
4. Never set for higher or lower torque values than those indicated
on your wrench.
5. For greater accuracy, clean all thread surf
aces and remove any
burrs on the fasteners being used.
6. WARNING- Never use your torque wrench to apply more
torque than its rated capacity.
7. It is not necessary to return this wrench to its lowest calibrated
value after use unless it is to be stored for an extended period
of time.
DO NOT OVERTORQUE
CERTIFICATION
This torque wrench is certified to be calibrated prior to
shipment to accuracy of +/-4% in the right hand direction on
readings 20% to 100% of capacity. On readings below 20% of
capacity, the accuracy is +/- two scale increments
.
LIMITED WARRANTY
If within 90 days from the date of purchase, this wrench fails
due to defects in materials or workmanship, we will repair
and recalibrate it free of charge. After 90 days and until one
year from the date of purchase we will repair any defect in
material or workmanship in the torque wrench free of charge.
This warranty does not include recalibration.
PROOF OF PURCHASE MUST BE INCLUDED WITH EACH
REQUEST FOR WARRANTY SERVICE.
For warranty service send the wrench to:
REPAIR AND CALIBRATION SERVICE
All torque wrenches should have periodic accuracy checks
and recalibration as required. This should be done at least
once a year or every 5000 torque application cycles,
whichever comes first.
Recalibration is also recommended after any abnormal
handling. For service send the wrench to one of the
Warranty Centers listed above of contact our Customer
Service department at [phone] for a list of additional
Approved Repair Centers.
REVISED/PRINTED IN USA APR 2014 FORM 6000M-90
ATD-112
INDUSTRIAL DUTY
MICRO-ADJUSTING
TORQUE WRENCH
OPERATING INSTRUCTIONS
1. STUDY THIS BOOKLET CAREFULLY
BEFORE ATTEMPTING TO OPERATE THIS
WRENCH.
2. NEVER APPLY MORE TORQUE THAN THE
MAXIMUM SCALE SETTING.
3. This Torque Wrench is designed for manual
tightening of threaded fasteners only. DO
NOT USE IT AS A NUT-BREAKER OR FOR
ANY OTHER PURPOSE.
4. Over torqued or defective fasteners and
sockets may suddenly break. Ratchets on
plain drives that are improperly engages,
worn out, damaged or over torqued, may
slip or break. TO PREVENT INJURY, KEEP
PROPER FOOTING AND BALANCE AT ALL
TIMES.
DO NOT USE THE WRENCH IN
PLACES FROM WHICH YOU MAY FALL OR
SLIP OR AROUND ROTATING MACHINERY.
5. This wrench will not prevent you from
applying more torque than set, it is not a
torque limiting tool. Learn how different
amounts of torque “feel”, so you will reduce
the possibility of damage and/or injury due
to accidental over torquing.
6. APPLY FORCE TO THE GRIP ONLY. DO
NOT USE “CHEATER BARS” (A Piece of
pipe placed over the hand grip for more
leverage).
7. There are no user-serviceable components
inside the wrench. Disassembling the
wrench or making any adjustments will
result in the lo
ss of accuracy, and will void
the warranty.
In the U.S.A.
Angle Repair & Calibration
175 Angle Drive
Beckley, WV 25801
www.anglerepair.com
972-864-6762
In Canada
ATG Torque Repair
7631 Bath Road
Mississauga, ON L4T3T1
1-866-691-6212