User's Manual

ManualsBrandsATD Tools ManualsWork LightATD Tools ATD 5493

Wireless Battery System Tester

User Manual

For Testing 6V & 12V Vehicle Batteries individually & in

Battery Packs. Also for testing 6V, 12V, 24V and 36V

Charging & Starter Systems

ATD-5493

Wireless to IR

to USB cable and

Adapter

Remote

Battery Module

Summary of content (8 pages)

PAGE 1
ATD-5493 Wireless Battery System Tester For Testing 6V & 12V Vehicle Batteries individually & in Battery Packs.
PAGE 2
INTRODUCTION The ATD5493 Wireless Battery System Tester tests all 6V and 12V lead acid batteries individually or in parallel and series battery packs. The tester will display the battery or battery pack condition as % available capacity, rated capacity (i.e. CCA’s), state of charge voltage and good, marginal or replace status. The ATD5493 also tests 12V, 24V and 36V starter and charging systems including starter draw, alternator output (loaded/unloaded), and diode ripple.
PAGE 3
UTILITY MENU OPTIONS The utility menu allows the user to set up the Language, Date & Time, Company Name, address, and phone #. To enter the Utility Menu: press MENU and HOLD DOWN the NEXT + button. Setting up the Language: The B600 will default to English. Press NEXT + to select the desired language and then press ENTER. Setting up the Date and Time: Press NEXT +. The display will show Date Time Setup. Press ENTER. The flashing cursor will blink over day month year format (dd/mm/yy).
PAGE 4
In Vehicle Tests BATTERY TEST: Connect the ATD 5493 Local Transmitter to the battery to be tested. The green Ready LED and the yellow Activity LED will blink. Press the MENU ON/OFF button to turn on the remote. “ATD 5493” will appear momentarily on the display and then the display will show WAITING TO CONNECT. When connected the green LED will stop blinking and the display will show IN VEHICLE TEST? PRESS YES (←). The display will then prompt the user to SELECT BATTERY/SYSTEM VOLTAGE.
PAGE 5
CHARGING SYSTEM TEST: IMPORTANT: Engine must be off before testing charging system. Charging system can also be road tested while driving vehicle*. After completing the starter test, press NEXT +. The display will prompt the user TEST CHARGING SYSTEM. (Note: the maximum starter/charging voltage is 36V). To test the charging system: 1. 2. 3. Press ENTER←: The user will be prompted to START THE ENGINE (ACCESSORIES OFF).
PAGE 6
Installing the USB CD System Requirements: Windows XP Service Pack 2 Minimum (Home or Pro), Vista (Home or Pro), Windows 7* (Home or Pro) & 32 Bit System 1. 2. Insert the CD into your CD-Rom Follow the simple onscreen instructions. The software will prompt you through each step of the installation. 3. If the software does not start automatically:  Click START on the Windows Taskbar  Chose RUN  Type D:\setup.exe (where D is your CD-ROM drive  Click OK.
PAGE 7
Printing the Data on your PC Printer To print the data using your PC printer, click on print button. The last entry will print. To print a different entry, click on the row to highlight. The data will print out on standard 81/2 x 11 size computer paper. Header information is entered in Setup (see page 3) NOTE: To properly test the Electrical System (Full Test) the test sequence should be Battery Test, Starter Test, and then Charging System Test.
PAGE 8
REPLACEMENT PARTS PART# PRT5493-01 PRT5493-02 PRT5493-03 PRT5493-04 PRT5493-05 PART DESCRIPTION BRASS POST ADAPTER FEMALE SET BRASS POST ADAPTER MALE SET CARRYING CASE LOCAL TRANSMITTER MODULE WIRELESS TO IR TO USB MINI CABLE PRODUCT SPECIFICATIONS Model # Name Battery Size Range DC Voltage: Range/Accuracy LCD Display mA Range (Parasitic drain test) Power Supply Cable Length (Local Transmitter) Wireless Signal Weight, lbs Warranty Wireless Range Normal dist.