User's Manual

ManualsBrandsATD Tools ManualsNoise Reduction MachineATD Tools Noise Reduction Machine 6561

ATD-6561

18” MASKING MACHINE

INSTRUCTION MANUAL

SPECIFICATIONS:

Construction: Sheet Metal

Overall Dimensions: L: 24” x W: 26-3/4” x H: 36”

Capacity: 2 Rolls of Paper

4 Rolls of Tape

Wheels: 1-1/2” x 8” Plastic

Net Weight: 21.5lb

PRODUCT FEATURES

• This cart provides a convenient, movable storage and work unit for masking paper and

tape.

• Hold two rolls of paper and 4 rolls of tape for convenient dispensing of masking

materials.

• Strong steel construction promises long service life

• Sturdy plastic wheels aid mobility, built-in trays and towel rack offer convenient features.

• Large tray stores extra rolls of tape, cleaning towels, cleaner and other materials.

• Small tray conveniently holds trimming knives and other tools.

• Towel rack holds and stores wiping towel.

USING THIS PRODUCT

This masking station will hold two rolls of masking paper, with two rolls of tape for each roll.

By aligning the tape with the edge of the paper, and threading the materials through each

cutter blade, it is possible to dispense and cut off a pre-assembled section of masking

paper with tape along two edges. This makes it very convenient to mask vehicles and other

equipment prior to painting or other treatment.

SAVE THIS MANUAL

You will need this manual for the safety warnings and cautions, assembly instructions,

operating procedures, maintenance procedures, trouble shooting, part list, and diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep both this manual and your invoice in a safe, dry place for future reference.

Summary of content (12 pages)

PAGE 1
ATD-6561 18” MASKING MACHINE INSTRUCTION MANUAL SPECIFICATIONS: Construction: Overall Dimensions: Capacity: Sheet Metal L: 24” x W: 26-3/4” x H: 36” 2 Rolls of Paper 4 Rolls of Tape 1-1/2” x 8” Plastic 21.5lb Wheels: Net Weight: PRODUCT FEATURES • This cart provides a convenient, movable storage and work unit for masking paper and tape. • Hold two rolls of paper and 4 rolls of tape for convenient dispensing of masking materials.
PAGE 2
WARNING Do not overload this masking station; Keep the weight load of material stored on this station balanced to prevent tipping. Use caution in working with the cutter blades, they are very sharp. NOTICE The warnings and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
PAGE 3
ASSEMBLY You will need an assortment of small hand tools to complete assembly of this Masking Station. 1. Find a suitable assembly area, and arrange the parts for the masking station where they can easily worked with. 2. Insert one Front Frame (07) into one Rear Frame (05) as shown in Figure 1. Insert the swaged end of the Front Frame into the curved portion of the Rear Frame near the handle. Be sure the lock buttons on the front frames fit into the holes in the rear frames. 3.
PAGE 4
5. Assemble the wheels. Slide one Wheel (02) and one Axle Nut per side as in Figure 3. Tighten the nuts. 6. Remove the Wing Bolts and Washers from each Spring Bar Assembly. Slide 2 sets of Paper Roll components onto each Spring Bar, as shown in the detail photo on page 10. 7. Place a Spring Bar Assembly between the upper-most holes in the Frame Assemblies. Insert the Wing Bolts and Washers through the holes in the Frame Assemblies and into the Spring Bar assembly as shown in the detail photo below.
PAGE 5
8. Repeat steps 6 and 7, placing the second Spring Bar Assembly between the large holes in the Rear Frame above the Large Bottom Tray. See Figure 4. 9. Insert one long bolt and large washer through the rear frame (as viewed from behind the wheels), using the hole located behind the hand grip. Place a large washer and nut onto the threads and tighten against the rear frame as shown in Figure 5.
PAGE 6
10. Repeat step 9 using the hole below the hand grip in the right rear frame. 11. Repeat step 9 using the holes located on the front frames just above the large bottom tray. 12. Select one of the bolts you have just installed, and thread a wing nut and washer half way onto the bolt. Thread the wing nut on so that the flat side of the wing nut faces to the inside of the frame assembly. See detail photo 13. Insert the metal bushings into the center of the tape roll holders. 14.
PAGE 7
17. Attach the small side tray to the right side of the assembly using two bolts, nuts and washers. 18. Attach the towel holder to the left side of the assembly. Insert the ends of the rack into the holes on the side of the assembly, rotating them upward to “hook” the rack into the frame.
PAGE 8
OPERATION When properly set up, this masking station will hold up to rolls of masking paper and up to 4 rolls of masking tape. These materials may be arranged so the masking station will dispense the paper with the tape pre-applied to the edges of the paper. This paper/tape assembly may be pulled out and cut from the masking station for easy and rapid use in masking work pieces for painting or other treatment. Installing the tape rolls 1.
PAGE 9
Installing the paper rolls: 1. Each spring bar assembly is designed to hold a full roll of paper. Select either spring bar for installation of a new roll of paper. 2. Remove the wing nuts on both sides of the spring bar assembly, and place the assembly on your workbench for installation of the paper. 3. Loosen the screws in one or both of the retainer sets, and slide them off the spring bar. 4. Slide a paper roll onto the spring bar, abutting the remaining retainer set.
PAGE 10
Threading the Paper and Tape through the Cutting Blades: Note: The upper tape rolls and upper paper roll will feed through the upper cutting blade. The lower paper roll and lower tape rolls will thread through the lower cutting blade. 1. Pull out the paper from the roll, and pass it behind the cutting blade, under the spring, over the cutting edge, and out to the front of the masking station. 2. Repeat step 1 with each roll of tape.
PAGE 11
PAGE 12