User's Manual

ManualsBrandsAtdec ManualsAudio Visual PresentationSingle Monitor Spring Arm Desk Mount

A-HDA-0818 Page 1 of 4

Installation Guide

A-HDA-0818

Heavy Duty Monitor Arm

COMPONENT CHECKLIST

REQUIRED TOOLS

Lower Arm

(x1)

Upper Arm

(x1)

VESA Plate

(x1)

Screw

M4x12mm

(x4)

6mm Allen Key

(x1)

4mm Allen Key

(x1)

Screw

M8x160mm

(x1)

Bolt Through

Plate

(x1)

Desk Clamp

(x1)

• Phillips Head Screwdriver

WEIGHT RANGE

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and oset VESA locations exert additional leverage that can exceed the

capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like

further information.

Flat Monitors

8 - 18kg

(17.6 - 40lbs)

Curved Monitors

8 - 10kg

(17.6 - 22lbs)

Summary of content (4 pages)

PAGE 1
Installation Guide A-HDA-0818 Heavy Duty Monitor Arm COMPONENT CHECKLIST A Desk Clamp (x1) B Lower Arm (x1) a Screw M4x12mm (x4) b Screw M8x160mm (x1) c Bolt Through Plate (x1) REQUIRED TOOLS • Phillips Head Screwdriver WEIGHT RANGE C Upper Arm (x1) D VESA Plate (x1) d 6mm Allen Key (x1) e 4mm Allen Key (x1) Flat Monitors 8 - 18kg (17.6 - 40lbs) Curved Monitors 8 - 10kg (17.
PAGE 2
82 49 (1.93”) (3.23”) (2.36”) 60 1A Base (7.87”) 1 d 170 170 75 (6.69”) 345 (6.69”) 170 (2.95”) 170 (13.58”) 515 345 (6.69”) (6.69”) (20.27”) (13.58”) 515 170 170 (20.27”) (6.69”) 345 75 75 (6.69”) (13.58”) (2.95”) 75 (2.95”) 515 170 170 (20.27”) (2.95”) (6.69”) 345 (6.69”) (13.58”) 515 (20.27”) 395 (15.55”) 240 82 (3.23”) 9.45”) 49 (1.93”) (2.36”) 82 (3.23”) 49 (1.93”) 240 1 (9.45”) 10-50 (0.4 - 2”) NW A ±90° Packing size N.W(kg) ±90° （mm） 10-50 (15.
PAGE 3
4 Adjust Arm Spring Tension Ⅰ ntity 4.1 Ⅱ Arm must be in horizontal position while adjusting Ⅲ Monitor remove e Ⅰ Adjust tension until the arm holds the monitor in top and bottom positions. Allow an extra cable length through the joints for movemet of arm Ⅲ Try more to make above adjustment based on monitor weight to get best 5 Cable management free-stop effect 5.
PAGE 4
8-20 Product Dimensions Product Size 60 200 (2.36”) Installation – Desk Clamp 10-50 (0.4 - 2”) 240 (7.87”) O Inner/Outside: 3/1 75 (2.95”) 100*100 395 (15.55”) (9.45”) 1 82 (3.23”) 49 (1.93”) I ±90° ±90° -30° 360° A 170 345 (6.69”) (13.58”) 515 (20.27”) 170 (6.69”) d+75° Desk thickness 10 - 50mm (0.4 - 2”) 75 (2.95”) 360° 10-50 (0.4 - 2”) Installation – Thru-desk ±90° ±90° Install 1 Procedure 2 +75° -30° 360° B d b Hole size ≥ 8.5mm (0.