Manual

ManualsBrandsAtdec ManualsComputersSD-AT-DW-BK

Component Checklist

Articulated Arm

Assembly (x1)

Cable Wrap

Applicator (x1)

Top Cap Tool (x1)

2.5mm Allen

Key (x1)

Cable Clip

(x3)

Extension

Clip (x4)

Component Checklist

Check you have received all parts against the Component Checklist above.

Bits Box

Mounting Fasteners

M4x10mm

Screw (x4)

M4x12mm

Screw (x4)

M4x16mm

Screw (x4)

16mm Cable

Wrap (x1)

5mm Allen

Key (x1)

Nylon Anchor

Plugs (x4)

M6x40mm

Coach Screw (x4)

Direct Wall Mount

Timber Stud

Wall

Direct Wall Mount

Bracket

4mm Hole

M6 Washer

M6 Coach Screw

B.1.2.

B.1. For Timber Stud Mounting - Use the Direct Wall

Mount Bracket to mark out the location of the required

four holes. (see diagram B.1.1.) Drill 4mm holes deep

enough to receive the M6 Coach Screws, insert the screws

and secure the bracket to the wall. (see diagram B.1.2.)

B.2. For Masonry Mounting - Use the Direct Wall Mount

Bracket to mark the location of the required four holes. (see

diagram B.1.1.) Using an

8mm masonry drill bit, drill four holes

41mm deep. Insert the Nylon Anchors and then secure the Bracket

to the wall using the M6 Coach Screws. (see diagram B.2.1.)

Installation Instructions

SPACEDEC ACROBAT

SD-AT-DW / WALL ARTICULATED ARM

Direct Wall Mount

Bracket

8mm Hole

M6 Washer

M6 Coach Screw

Brick or Concrete Wall

B.2.1.

S8 Nylon Anchor

Front View of the Direct Wall

Mount Bracket

B.1.1.

Direct Wall Mount

Bracket Assembly (x1)

M6 Washer (x4)

Refer to Ergonomic guidelines overleaf to determine best position to mount wall bracket.

Note: Ensure Bracket is

mounted Vertically

Top Cap

Threaded Rod

Bottom Cap

Direct Wall Mount

Bracket

Summary of content (4 pages)

PAGE 1
Installation Instructions SPACEDEC ACROBAT SD-AT-DW / WALL ARTICULATED ARM Component Checklist Bits Box Cable Wrap Applicator (x1) Cable Clip (x3) M6 Washer (x4) M6x40mm Coach Screw (x4) Nylon Anchor Plugs (x4) Articulated Arm Assembly (x1) 16mm Cable Wrap (x1) Direct Wall Mount Bracket Top Cap Tool (x1) Extension Clip (x4) Top Cap 2.
PAGE 2
B Direct Wall Mount Continued. B.3. Attach the Spacedec Arm to the Direct Wall Mount Bracket. (see diagram B.3.1) Tighten the Top Cap with the supplied Top Cap Tool. (see diagram B.3.2.) 4 Tighten using the Top Cap Tool Insert Threaded Rod and Top Cap C 75mm x 75mm (3” x 3”) mounting hole pattern Display 75mm (3”) 75mm (3”) 4x10mm Screws 3 Arm with inner tube 1 100mm x 100mm (4” x 4”) mounting hole pattern 4x12mm or 4x16mm Screws Plastic Bottom Cap B.3.1.
PAGE 3
f Ergonomic Guidelines Recommended Mounting Position When mounting the Spacedec Acrobat Wall Articulated Arm, ensure the correct focal distance can be achieved for ultimate visual comfort (Refer to Recommended Viewing Distance / Height below) Wall Mount Recommended Viewing Distance / Height B Ergonomists recommend that the optimal position of your screen should be slightly below eye level. When looking at the screen’s centre the user should have a downward visual angle of approximately 10°-20°.
PAGE 4
G Adjusting the Display The Spacedec Acrobat Wall Articulated Arm comes factory set to support 6kg displays. Adjust the arm to suit the weight of your display as shown in the following steps: G.1. Adjusting the Ball Joint Resistance Depending on the weight of the display, it may be necessary to make adjustments to the Ball Joint Mechanism.