Specifications

ManualsBrandsAtdec ManualsTVs & monitorsSD-SA-DK-DB-P

Component Checklist

Installation Instructions

SPACEDEC ACROBAT

SWING ARM DOUBLE

Swing Arm

Assembly (x2)

Cable Wrap

Applicator (x1)

Top Cap Tool (x1)

2.5mm Allen

Key (x1)

Cable Clip

(x4)

Extension

Clip (x8)

Bits Box

Mounting Fasteners

M4x10mm

Screw (x8)

M4x12mm

Screw (x8)

M4x16mm

Screw (x8)

16mm Cable

Wrap (x2)

Washer (x1)

Base Casting (x1)

Spacer Tube

Assembly (x2)

M8 Interscrew

(x1)

M8 Nyloc Nut (x1)

Cable Manager

Tube Clip (x1)

5mm Allen

Key (x1)

M4x16mm

Countersunk

Screw (x3)

Desk Clamp Box

M8 Desk Clamp

Screw (x1)

Pressure

Plate (x1)

Inner Tube Post

Desk Clamp

Bracket (x1)

Component Checklist

Threaded Rod

and Top Cap

(x1)

Component Checklist

Possible Configurations

Spacedec Acrobat Swing Arm Double can be

assembled in a number of different configurations

depending on the users requirements.

Two such examples are shown below and right.

Arm, Spacer, Arm, Spacer

Side by side displays

Arm, Arm, Spacer, Spacer

Back to Back displays

Summary of content (4 pages)

PAGE 1
Installation Instructions spacedec ACROBAT swing arm Double Component Checklist Component Checklist Bits Box Cable Wrap Applicator (x1) Swing Arm Assembly (x2) 16mm Cable Wrap (x2) Spacer Tube Assembly (x2) Cable Manager Tube Clip (x1) Cable Clip (x4) M8 Interscrew (x1) Base Casting (x1) Washer (x1) Threaded Rod and Top Cap (x1) M4x16mm Countersunk Screw (x3) Inner Tube Post M8 Nyloc Nut (x1) Desk Clamp Box 5mm Allen Key (x1) Pressure Plate (x1) Desk Clamp Bracket (x1) M8 Desk Clamp Screw (x1)
PAGE 2
Component Checklist a Check you have received all parts against the Component Checklist on the previous page. Assemble the Arm b B.1. Disassemble the Tube Assembly You will need to disassemble the Tube Assembly before assembling the Swing Arm Top Cap and Threaded Rod B.2. Assemble the Swing Arm Assemble the Swing Arm in the desired configuration ensuring all components are used as shown.
PAGE 3
C Mounting Options Continued C.2. Bolt Through Top Cap Tool C.2.1. Drill Mounting Hole Drill a 13mm (½”) hole in your work surface at the desired location for your arm. C.2.2. Install as shown Insert the M8 Interscrew up through the hole in the work surface. C.2.3. Using both hands, secure the M8 Interscrew with the 5mm Allen Key supplied in the Desk Clamp Box and use the other hand to tighten the Threaded Rod into the Interscrew with the supplied Top Cap Tool. (see diagram C.2.3.
PAGE 4
G Ergonomic Guidelines Recommended Mounting Position When mounting the Spacedec Acrobat Swing Arm Double, ensure the correct focal distance can be achieved for ultimate visual comfort. H Adjusting the Display The Spacedec Acrobat Swing Arm Double comes factory set to support 6kg displays. Adjust the arm to suit the weight of your display as shown in the following steps: G.1.